Search Documents

Jan 1, 1932

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By W. P. Yant

Canister-type gas masks Pave become an essential part of the equipment of many industries, not only for use in .emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau bas become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely, remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760° C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and sub-sequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove..

Jan 1, 1932

By G. S. Price

This paper, which describes the milling practice at the Page concentrator of the Federal Mining and Smelting Co., is one of a series being prepared by the Bureau of Mines. The Page mine and mill are located on Silver Creek, 3 miles west of Kellogg, Idaho, and 1 mile south of United States Highway No. 10. Supplies and concentrates are hauled by truck over an automobile road which connects Highway No. 10 with the property. The concentrator has capacity to treat 300 tons of ore per day and utilizes all-flotation methods of treatment. Power is supplied from the main line of the Washington Water Power Co. which runs from Spokane, Wash., to Kellogg, Idaho. Water is obtained from the mine and also from a well which is situated 1 mile distant from the concentrator and about 600 feet in elevation below the concentrator.

Jan 1, 1932

By R. G. Knickerbocker

THE copper smelter and refinery of The Messina (Transvaal) Development Co. Ltd., at Messina, South Africa, was erected in 1920 and 1921, but initial operations were deferred until late in 1922 on account of the collapse of the copper market in the interim. Because the anticipated production was to be only 20 tons of copper per day from a high-grade matte containing 60 per cent copper, and because the ore did not contain gold or silver in quantities sufficient to pay for separation from the copper bullion, it was decided to design the plant along lines quite different from the modern smelteries treating large quantities of sulfide ores carrying appreciable amounts of gold and silver. The plant was built, therefore, for the production of copper by the Nicholls-James process. By this method two-thirds of the copper matte produced was roasted in a Merton calciner and charged into a bath of the remaining one-third portion of unroasted matte in a reaction furnace. The original design was not only novel in providing for the Nicholls-James process, but also in comparison with new plants built elsewhere, because of factors inherent in the locality. Sources of supply for machinery were very remote; it takes three months after the placing of an order to accomplish delivery of machinery into Messina from the United States. Native labor was available at 30 to 40¢ per 8-hr. shift. These factors permitted plant design which provided no overhead cranes, no matte ladles, no slag pots or other usual mechanical means of transportation between departments. The design resulted in a compact simple plant with furnaces arranged close together and. terraced so as to provide for gravity transfer of molten material from one furnace to another and for manual disposal of products. Fig. 1 shows the relative location of furnaces. The three furnaces are parallel on successively decreasing elevations. A superimposed feed floor was provided above the furnaces. All three furnaces were provided with coal-dust burners served from a Bonnot system of coal-dust transportation, and the waste gases were discharged into waste-heat boilers.

Jan 1, 1932

By H. N. Herrick

The flow characteristics of drilling muds, as described in this paper, and the method given for solving problems relating to the flow of these muds through pipe and accessory equipment, are based on a conception that drilling muds are plastic solids like paints or greases; not liquids. The data presented in this report have been obtained from studies of California muds, chiefly those used in the Kettleman Hills field, by the Producing Department of the Standard Oil Company of California. Although no claim of scientific exactness is made for the formulas and diagrams, since the data upon which they are based are not complete even for California muds, the method has proved to be a convenient means for estimating, closely enough for practical purposes, the pressures required to force muds at various rates through pipe systems in which-they are handled. Certain approximations have been made to simplify the procedures so that they can be used easily in the field. Viscosity and Shearing Strength of Mud For the purpose of this discussion a plastic solid is defined as a material in which no deformation or flow takes place when the material is subjected to shearing forces, until the shearing force reaches a value called the "yield point." With liquids, the smallest force will produce continuous deformation; that is, the yield point of liquids is zero. The difference between true liquids and muds is illustrated in Fig. 1, which shows rates of flow through a small tube under different pressures. The flow rate of the liquids is directly proportional to the pressure and that of the muds is not. The behavior of drilling mud does not conform in every detail with the definition of a plastic solid as given, because mud actually flows slightly at pressures below its yield point. However, for practical purposes the definition describes the condition adequately and has the advantage of simplicity. In order to make mud-flow calculations based on the theory that mud is a plastic solid, it is necessary to know the "yield point" of the mud, which hereinafter is defined by equation 1 under the caption "Viscosity

Jan 1, 1932

By A. O. Dufresne

A Step which, it is believed, will prove extremely beneficial to the Quebec asbestos-mining industry was taken during 1931, when the asbestos mine operators of the Province assembled to work out a uniform method of naming the products of their mines. The outcome of several meetings was the drawing-up of a classification which defined, limited, and designated anew the numerous grades of asbestos marketed. It entailed no drastic departure from the existing processes of grading, nor any revolutionary changes in methods of testing, but aimed rather to perfect existing methods. The classification proposed has been accepted by all operators in the Province, who, from January first of this year, began introducing the new nomenclature. Unless one is conversant with the properties and mode of occurrence of chrysotile asbestos, with the unique milling methods devised for its recovery, and with the history of the development of their technique, he may not readily understand the basis of the new classification. For information on these and other data concerning the industry, the reader is referred to a recent publication, Chrysotile Asbestos in (Canada, by James Gordon Ross, issued by the Mines. Branch of the Department of Mines, Ottawa. The object of this paper is to present briefly some of the phases in the evolution of the classification of Canadian chrysotile asbestos, in the hope that the recent effort to standardize the marketable products of one of Canada's most important non-metallic mineral industries will open a field for discussion, fruitful in new ideas and constructive suggestions. The necessity for the grading of asbestos results fundamentally from the fact that the price per ton depends on the length of fibre. At all times in the history of the industry, the very limited available supply of the longer grades, as well as the requirements of the trade, have caused relatively very high prices to be paid for fibre over half an inch in length, while for the shorter grades the price decreases rapidly, and at a rate which bears no proportionate relation to the length of fibre.

Jan 1, 1932

By B. R. MacKay

Introduction Of all Canada's mineral resources, its coal deposits have probably received the most continued attention by the Geological Survey since its inception ninety years ago. A casual review of the many geological maps of coal areas by the Geological Survey will show how geological and topographical detail on the maps has gradually increased to meet the ever urgent demands of the mining industry. In the early stages of exploration, the mapping done, especially in the coalfields of the Rocky mountains, was largely of a reconnaissance nature. On these maps the topographical relief, where shown, is indicated by form lines or by hachures, the boundaries of the coal-bearing formations are only approximately defined, and the geological structure of the coal seams is illustrated by one or more generalized cross-sections. Once mining development on a coal area began, there arose a demand for more detailed maps. To meet this need, topographical and geological maps on a scale of one inch to a mile were made, in which the ?topographical relief is shown by contour lines having generally an interval of 100 or 200feet. On the geological maps, the boundaries of the formations are accurately delineated, and the geological structure of the area is illustrated by one or more structure sections drawn across the area, which show the position and attitude of fault lines, the crests and troughs of folds, and the attitude of the various formations (See maps of Costigan Coal Field, 1905, and Cascade Coal Basin, 1907, by D. B. Dowling).

Jan 1, 1932

Jan 1, 1932

In another paper the author described the electrolytic preparation of highly-purified lead. One of the most difficult parts, yet perhaps the most essential part, of that research was to ensure, firstly, that the purification process should be effective; secondly, that it should remain effective; thirdly, that the lead should not be contaminated during the tests that were done on it. All this necessitated periodic analyses of the lead.The purpose of this paper is to describe the work done by the author to check the accuracy of some known rapid methods for the estimation of impurities in highly-purified lead, with the intention of applying them to the control of the electrolytic process above-mentioned.METHODS ALREADY IN USEThe literature sets out accurate methods for the estimation of impurities in lead, but these methods are both lengthy and expensive. For example, the method described by Hemingway is used in the Port Pirie laboratory of the Broken Hill Associated Smelters Pty. Ltd., but it requires a sample as large as 1000 grm., and the time required to analyse a sample extends over days, and is too long to allow of quick control over a running process. This method was used by the Associated Smelters to obtain the analyses quoted in another paper by the author.

Jan 1, 1932

From time to time failures occur in structures made of lead, and the failure may be due to corrosion involving a definite thinning of the lead sheet, or it may be of such a nature that cracks develop and the lead appears to disintegrate. The idea of lead cracking will at once suggest something abnormal, for common experience shows that this metal is very ductile and will withstand considerable bending without showing any sign of fracture. Cracking, on the other hand, is usually associated with brittleness.Fig. 1 is a natural-size photograph of a cracked sheet of lead. Prior to photographing, the sheet was etched byimmersion in a solution of ammonium molybdate. Several characteristics of this crack will be evident. First of all it is distinctly a zigzag crack, and secondly it passes between, rather than through, certain well-defined areas which appear bright in the photograph. This is particularly noticeable at the lower end where the crack appears to terminate.

Jan 1, 1932

By J. B. Newsom

DURING July and August, 1931, the Bloomington Limestone Co.,. at Bloomington, Ind., ran a single wire saw on ledge No. 2 at Maple Hill quarry. The ledge was hard rock, much harder than the average Indiana limestone. It was opened at two ends for a depth of about 20 ft., leaving a 130-ft. section between. During the tests 21 cuts were made in this ledge, to an average depth of 10.42 ft., for a total effective cutting area 028,445 sq. ft. The actual area sawed was about 20 per cent higher, as we did not level down in the center, preferring to cut deeper on the ends. The various cuts were carefully, logged, and the results plotted. A study of these results is interesting, as it enables a forecast of probable future costs to be made, and also because it points out the limitations of wire saws, and the lines development should logically take. Some of the inferences to be drawn are discussed below. Best Length of Cut.-No. trouble was due to length of cut, except that we could not easily level down a long cut, and it is probable that longer cuts, say up to 200 f t., can be made. Obviously, longer cuts will result in a higher sawing rate, in square feet per hour if- they do not cause stoppages. Working Higher Ledges.-The cuts averaged 10.42 ft. high by 130 ft. long. A study of several logs indicated that during only about 15 per cent of the cutting time was the saw cutting to its full efficiency; that is, during about 85 per cent of the time the saw was bedding in at the ends and not cutting well in the center, or the ends were below the floor line and only part of the wire was doing effective cutting. This does not mean that the wire was cutting to only 15 per cent of its capacity, but it means that during about 85 per cent of the time part of the cutting was being wasted. If higher ledges had been worked, the wire would have cut to its full efficiency a large part of the time, as it would have had a greater distance; to saw after it had bedded in to the ledge before the ends went down below the floor level. The exact saving to be expected cannot be calcu-lated, but it would be large, if really high cuts were made.

Jan 1, 1932

Jan 1, 1932

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd M.emoria1 Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense.

Jan 1, 1932

By T. W. Guy

DuRing recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures. Early Cleaning Methods In the early days, the tipples were simple wooden structures, with bar screens for separating the fines from the lump coal. All cleaning was done by the miners at the face, or by pickers in the railroad cars. Gates were provided in the chutes by which the flow of coal could be stopped when necessary while the pickers raked the surface of the coal in the car and picked out the impurities. A large percentage of the fine coal or slack was used for making coke at the mines in beehive ovens. The

Jan 1, 1932

By Irwin Roman

The literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years,' but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data.2 There seems to be a general reluctance among geologists and engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1932

By J. E. Gill

Introduction During the past summer, detailed geological mapping was extended to cover the entire group of 31 claims owned by Waite-Ackerman-Montgomery Mines, Ltd., and considerable new information was revealed by development and exploratory work underground. These new facts provide a more complete view of the lithology and structure of the area than has heretofore been available. They also necessitate revision of certain interpretations presented last year by Peale (l), and have served to straighten out some of the problems suggested by Porritt (2). The purpose of this paper is to outline in a broad way the relations as now understood and to discuss in detail certain points which should be of interest to members of the Institute. Maps and records by the mine staff have been freely used in arriving at the interpretation presented in the following pages. The writers are especially indebted to Mr. R. V. Porritt, the mine manager, with whom many of the problems touched upon were discussed on the ground and whose intimate knowledge of the geology of the underground workings aided greatly in testing various hypotheses. The writers have profited greatly, also, from close association with Dr. W. F. James during the course of the work. Permission to publish the included data has very kindly been given .by the management.

Jan 1, 1932

Jan 1, 1932

By Arthur Phillips

THE study of anisotropy in metals has been greatly stimulated in recent years by the rapid development of X-ray methods for determining the crystallographic relationships of wrought and annealed materials. Prior to this time the knowledge regarding the directional properties of commercial alloys consisted almost exclusively of observations of a practical nature made during the fabrication of metal objects, supplemented by a limited number of mechanical tests on specimens cut at various angles to the direction of working. Such observations clearly indicate that the common methods of cold-working metals cause both a crystallographic and a mechanical fibering varying in character and degree according to the nature and extent of the deforming process. Even after annealing, following certain not too well known combinations of reductions and anneals, a preferred orientation may exist, thereby constituting a residual fiber effect sufficiently pronounced to manifest directional properties. With the application of the X-ray the experimental horizon was extended chiefly because the study of anisotropic metals promised to offer direct and quantitative evidence regarding the involved mechanism of fragmentation and plastic flow. As a natural consequence the intensive studies in this direction have yielded a vast accumulation of data of ultimate potential value. Unfortunately, however, as is commonly the case in entering a virgin field of experimentation, many of the data cannot be molded into complete and coherent form because of the many unrelated conditions of the experimental projects. Again, the results of the study of single crystals have been rather naturally but at times indiscriminately applied to polycrystalline metals. Furthermore, sweeping statements have been made regarding the behavior during working and annealing of metals and alloys, entirely on the basis of similarity in lattice arrangement. There is abundant reason for believing that relatively small concentration variables, differences, in magnitude and distribution of applied stresses, and the character of associated annealing treatments may in some cases greatly influence the mechanics of flow and consequently largely determine the final structural characteristics of the metal.

Jan 1, 1932