Search Documents

Jan 1, 1937

By W. J. Reagan

In a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the various sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be invoIved.

Jan 1, 1937

Executive R. C. ALLEN, Chairman ERLE V. DAVELER, Vice-chairman WILDER JUDSON R. M. ROOSEVELT G. B. WATERHOUSE Finance H. G. MOULTON, Chairman HENRY KRUMB PAUL D. MERICA H. T. HAMILTON, Consultant Admissions W. B. HEROY, Chairman GEORGE D. BARRON, Vice-chairman H. T. HAMILTON PHILIP KRAFT W. A. SINSHEIMER

Jan 1, 1937

By H. R. Reed

THE cost of hoisting with electricity in deep mines is a matter about which little information has been published. This paper makes a detailed study of such costs and presents the information in a series of curves. In particular the curves show the cost of hoisting ore from depths varying from 500 to 7000 ft. Vertical with the shaft at 70° incline for the double cylindroconical and double cylindrical drums, the hoists operating balanced, using Ward Leonard and Ilgner-Ward Leonard control, and designed for most economical operation from each depth. Operation with the double cylindrical drum is expanded to cover hoisting from 2000 to 5000 ft. using equipment designed for 5000 ft. and from 4000 to 7000 ft. using equipment designed for, 7000 ft. Additional curves are included to show the ratings of the necessary hoist motors, energy input per hoisting cycle and size of flywheel in tons for complete equalization when the Ilgner-Ward Leonard system is used, also hoisting efficiency. The duty imposed on a mine-hoist motor fluctuates between wide limits during a cycle of operation. The demand on the motor may vary from a large horsepower value' near the beginning of the cycle to a small or a negative demand near the end of the cycle. Such factors as tonnage to be raised per hour, depth of shaft, and balanced or unbalanced opera-tion have such a marked effect on the operating cycle and vary to such an extent for different mines that no set of rules can he formulated for quickly determining the size of the motor required. The duty cycle from which the motor rating is (derived must he determined for each case according to the conditions of the proposed hoisting operations. The motor torque required at the cardinal points of the duty cycle is determined from the moment or torque in pound-feet necessary to raise and lower the load and ropes, accelerate and retard the load, ropes, drum, etc. The torque diagram depends largely upon the type of drum. Two different types of drums, if used on exactly the same duty cycles, may have widely different peak demands and capacities of hoist motors. The essential feature in the design of hoisting drums and in determining

Jan 1, 1937

By Paul A. Beck

It is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation. the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and " consume " the deformed hard material. The extent of stability attainable through recovery is limited, especially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or polycrystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "istraight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals—a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By J. M. Hassler

Nowhere can there be found a more misleading statement than the old one that "Iron can be manufactured cheaper in the South." During the past decade ironmakers and users of iron have heard varied and sundry stories of the wonderful resources of the Birmingham district, including abundant ore and coal fields, cheap labor, a wonderful climate and similar industrial Utopian statements. Birmingham represents the major portion of the iron business in the South, and as Birmingham fares so goes the iron business of the South. The intent of this paper is to shed some light on the actual conditions surrounding ironmaking in the South, especially in the Birmingham, or North Alabama, district. By a presentation of facts it is desired to point out that the "cheap iron" of the industrial South is a thing of the past, primarily because of increased labor cost and because labor is radically different in performance to what it was years ago. Also, because most of the raw materials needed in ironmaking that would be classed better than inferior are gone. Important Factors The several important factors that have been responsible for this change are : 1. Shrinkage of the iron business in the South. 2. Increased labor cost. 3. The development of the South, with an industrial trend, without a substantial increase of its own iron-consuming market. 4. Increased freight rates, which has narrowed the market that might be reached from this district. 5. Depletion of the better grades of raw materials, both ore and coal. Shrinkage of Iron Business in South.—Table 1 was prepared in early 1936 and revised in 1937, of blast-furnace units in the North Alabama district, considering the year 1936 compared with a maximum number of furnace units of previous years, the peak point being very near the year

Jan 1, 1937

By Walter Kauenhowen

GeRmany's crude-oil production during 1936 totaled 3,112,494 bbl., an increase of 5.2 per cent over the 3,007,711 bbl. produced in 1935. The official monthly production figures published in 1936 report only the individual production figures of the three old established fields, whereas since 1936 official reports combine the production of all other fields into one figure. According to these published data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1936 was as follows:

Jan 1, 1937

By N. A. Rose, E. L. Spain

THIS study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. INTRODUCTION When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel- exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfulls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. SOURCES AND TYPES OF MATERIALS The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1937

By E. L. Garton

Michigan is becomining one off the important oil-producing States of the country, The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 1935.4/ The Bureau of Mines method of crude-oil analysis and classification indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the tame amount of kerosene and gas-oil combined, 12 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue of about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in S counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

Masjid-i-Sulaiman Field.—During the past year, drilling activities have been limited to repair work. No new developments of importance can be recorded in production technique. Fall of dome pressure is maintained at the 1 lb. per sq. in. per annum rate mentioned in previous reports. Acid treatment of wells is being increasingly used and for wells in fissured areas has been very successful. Such wells have been converted into first-grade producers with substantial drops in bottom-hole differential pressures. The effect of acid treatment has been to increase the flowing lives of wells so treated. The normal procedure consists of threo treatments of 500 gal. commercial acid diluted 100 per cent but success has been met with fewer applications. The policy of returning products to the resorvoir has been continued. The total quantity of products returned since the policy was commenced in 1929 now amounts to approximately 30 million barrels. Haft Kel Field.—The drilling of the main Haft Kel structure for production purposes has now been completed. Production and control wells have been completed to meet the rate of production anticipated over the next few years.

Jan 1, 1937

By A. V. Henry

THE kaolins of the southeastern United States were known to civiliza-tion as early as the latter part of the eighteenth century-and yet the Fig. 1.-KAOLIN PRODUCTION AND IMPORTS. commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported.

Jan 1, 1937

By Frank C. Greene

Drilling for oil and gas in Missouri continued at a slightly lower rate than has been prevailing. A summary of operations for the past few years as compiled and published by the Missouri Geological Survey and Water Resources is as follows: Two oil pools are being developed in Cass County. Neither area has been drilled completely, and detailed descriptions will not be given at this time. In the Endicott pool in the southern part of T. 44 N., R. 33 W., oil is found in the Warrensburg sand, which is now considered to be the Big Lake sand of eastern Kansas. The top of the sand is about 125 ft. below the Herthalimestone. The best well is reported to have made 14 bbl. per day for the first four days. The oil is 30" to 32' BB. gravity. This is the only pool in the state, aside from the older areas on the east and west edges of Lees Summit, Jackson County, that is producing oil from the Warrensburg sand. Drilling continues in the Knoche pool in the central part of T. 46 N., R. 33 W., where the oil is found in the Squirrel sand. The oil produced by both these pools is sold by truck in Kansas City.

Jan 1, 1937

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing gypsum mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation so that there may be no misunderstanding of the scope of the cost tabulation. This paper deals specifically with the mining and crushing methods employed by Victor Plaster, Inc., Victor, Ontario County, N. Y. The maximum annual production capacity of this company is 150,000 tons of crushed gypsum. The methods and practices employed arc typical of those followed in the gypsum mines in western New York State. The shaft is, perhaps, the deepest and the thickness of the gypsum mined is above the average for the section.

Jan 1, 1937

Jan 1, 1937

By E. J. Bruderlin

A metallurgical process to be economically successful must be carried on under proper conditions of control and equipment. The question of equipment is always of primary importance. In the distillation process for the recovery of zinc by retorting, the retort is the all-important piece of equipment. Each retort in a working blóck must function as a separate unit. Over-all block efficiency is the result of the ability of the individual retort to withstand the severe conditions of operation for a maximum period of time. Therefore retort manufacture has been an ever present problem with the operator of a zinc-retorting plant. During recent years the zinc-plant operator has been faced with rapid changes in the character of the ores and concentrates. Operating costs have increased as a result of the introduction of the flotation process and the amount of flotation concentrates to be handled. To counteract increasing costs, the operator has found it necessary continually to attempt heavier loading of retorts, until a 45 to 50-lb. charge per cubic foot of retort space has become common practice. Heavy loading has brought about severe firing conditions, which, in turn, have emphasized the necessity for further improving the quality of the retort. Increasing percentages of detrimental impurities in the retort charges have also added to the operator's difficulties. Amarillo Silicon Carbide Retorts At the Amarillo plant of the American Smelting and Refining Co. a retort made of a suitable plastic clay grogged with silicon carbide has been found to best meet the present-day requirements. Retorts of this kind have been in use at Amarillo for 8 years and have shown an average furnace life of approximately 175 calendar days. The Amarillo retort is cylindrical in shape and after burning is approximately 83/4 in, inside diameter by 60 in. over-all length. The wall thickness is 136 in., except for the butt of the retort, which is approximately 2½ in. thick. The retort mud has a shrinkage of 3 per cent, or approximately % in. per foot. The silicon carbide retort after being properly dried weighs about 211 lb. When the retort is fired and ready to go into use the weight decreases to approximately 203 lb.

Jan 1, 1937

By T. B. Gyles

Zinc is made by the National Smelting Co. and its associates by both the horizontal retort process and the vertical retort process developed by the New Jersey Zinc Co. This paper deals only with the horizontal retort practice at Avonmouth. That the horizontal retort process does survive in all countries in some form or other is due to at least partial success in overcoming some of the inherent difficulties of the process. The horizontal retort furnaces ran into considerable difficulties when the product of the selective flotation of mixed lead and zinc ores became the normal material for treatment. It is necessary, therefore, to make some reference in connection with the process to the preliminary treatment of the ore prior to distillation.. Therefore we include some small reference to this aspect in our description. Furnace Design and Structure Of the types of furnaces in operation at the company's various works, those at Avonmouth are perhaps more typical of the trend to utilize large units, with a subsequent saving in costs, such as heating and supervision.

Jan 1, 1937

By W. E. Cockfield

THE object of this paper is to review recent geological work in the Cariboo district and to present notes on the recent development of mineral properties. The Geological Survey has done considerable work in the Cariboo district, extending over a period of years. In 1885 and 1886, Bowman (1) mapped the geology of a large area. In 1922 and 1923, Johnston and Uglow (2) mapped Barkerville area in some detail and prepared a report on the placer and lode gold deposits. In 1931 and 1932, Cockfield and Walker (3) mapped the Quesnel Forks area. In 1933, Hanson reported on Willow River area ( 4), and in 1934 made a detailed examination of part of the Barkerville area (5). In 1935, Lang commenced work on the Keithley area, lying to the southeast of the Barkerville area, and in 1936 published a preliminary re-port (6). The work on Keithley area was continued in 1936 by both authors of the present paper. As the results of the earlier work have been published, this paper will be concerned largely with Keithley area, that is, the part of the region lyinp between longitudes 121° 00' and 121° 30', and latitudes 52° 45' and 53° 00 . This area lies astride Cariboo (Swamp) river and extends north some 17 miles from Keithley, which is situated near the southern border of the map-area (see sketch-map). Points in the western part of the map-area are fairly accessible. A road extends from Barkerville to upper Cunningham creek, and from this a trail crosses Snowshoe plateau to Keithley. A second trail from this road leads to the lower falls on Cariboo river. From this road, a branch road leads to upper Antler creek, with a trail leading from this branch road to Keithley. Part of this western half of the area is made up of the Snowshoe plateau, which constitutes a gently rolling surface, at or above timber line, where trails are largely unnecessary.

Jan 1, 1937

By H. A. Doerner

The process for smelting zinc developed several centuries ago is still in use. Through the experience accumulated over this long period of time, details of the process have been perfected until there is little opportunity to make any further improvement except by a radical change in method. Such a change was accomplished by the process recently developed by the New Jersey Zinc Co. The process to be herein discussed is a still more radical departure, which has been developed to large-scale laboratory operation by the Metallurgical Division of the U. 5. Bureau of Minesl. † The reduction of zinc oxide by carbon is a highly endothermic reaction, which requires temperatures in the range 1200° to 1400' C. for even a slow reaction rate. The transfer of the heat of reaction through thick fire-clay walls, the high radiation loss in the type of furnace used, and the practical impossibility of recovering or using the combustible products of the reduction (CO) cause a deplorable waste of fuel. With the one exception mentioned, all zinc smelting is done in small retorts manually charged and discharged. Attempts to mechanize these operations have been only partly successful, and there seems to be no way to avoid or improve the uncomfortable conditions in which the work is done. The reduction of zinc oxide by methane has a relatively high reaction rate at 1000' C. At this temperature most ore residues do not sinter, and it is possible to use metal retorts. These factors make gaseous reduction especially adapted to a continuous operation and compared to reduction by carbon make possible: (1) higher rate of reaction at lower temperature, (2) more nearly complete extraction of the zinc, and (3) much better utilization of fuel and reagent. Although the reaction between methane and zinc oxide requires 105,900 calories per mole, compared to 86,860 cal. in the carbon reduction, it is obvious that much less fuel will be required to supply 105,900 cal. through 36 in. of metal at 1000' C. than to transfer 86,860 cal. through 1 in. of fire clay at 1300° C. Moreover, the gaseous products of gaseous reduction (CO and H2) can supply 183,430 cal. by complete combustion.

Jan 1, 1937

By E. L. Bruce

GOLD occurs in many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at. Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be conned to representative types of deposits, chiefly those of major importance; a few others, differ-ing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwest-ern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubt-edly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however,, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambriang old deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937

By Oliver C. Ralston

Nonmetallic technologic investigations of the U. S. Bureau of Mines are headquartered at experiment stations in three widely separated localities of the United States. During 1936, the Nonmetals Division of the Technologic Branch was formally set up by combining the direction off the work of these three experiment stations under one administration. The New Brunswick (N.J.) station which in the past has been known as the Nonmetallic Minerals Experiment Station, is henceforth to be at College Park, Md., as part of the Eastern Experiment Station, and its principal activities will be related to the nonmetallic resources of the Eastern and New England States.

Jan 1, 1937