Search Documents

By C. E. Rodgers

WHEN I was asked to prepare, for presentation at the 1938 Annual Meeting of the Institute, some data concerning low-discharge grinding at the Sylvanite mill, it seemed entirely reasonable to expect to have at my disposal the results of at least four full months' operation after the last unit, as then proposed, was installed. Delays in delivery of equipment, nevertheless, shortened the interval, as will be shown herein. In submitting the data contained in this discussion, I wish distinctly to state that the intention is not to claim that final conclusions can be reached at this time concerning our operation. Test periods, in certain instances at least, have been too short for this purpose, although some, where so stated, have been extended through March and April. It is hoped, however, that an advantageous trend in practice can be shown and that the experience related may be of interest to others who are now operating, or who are considering the operation of, low-discharge grinding mills. In the plant under review, four mills are in use: one primary and three secondary. Present mill capacity (grinding, as shown by screen test, about 99 per cent through-200-mesh and approximately 88 to 89 per cent minus-325-mesh with infrasizer giving about 90 per cent of the latter) averages about 525 tons per day. A brief description of each unit will be given and comments will also be made relating to operation. This will be followed by certain test data from which, in conclusion, operating results are summarized.

Jan 1, 1938

By Eugene McAuliffe

IT is not possible to include in this paper, limited as it is in scope, the many diverse steps toward the reduction of mine accidents that are taken in the mines that produce the nation's coal. Every coal-producing state has enacted laws covering proper mining practices, and the major portion of these are directly related to the safety of the mine employees. The United States Bureau of Mines, the American Institute of Mining and Metallurgical Engineers, The American Mining Congress, a number of national, regional and state organizations, as well as the coal technical press, have covered time and time again all of the "do" and "don't" phases of mine operation that bear on the important question of mine and employee safety. Within the past 15 years The Union Pacific Coal Co. has attempted to put into practice in its mines in southern Wyoming these many good recommendations, finding some value in all, and yet, to secure substantial results, the management found it necessary to resort in the end to what might be referred to as "extra-territorial" methods. It is the writer's purpose to show in this paper that marked and even extraordinary betterment can be brought about when employer and employee work together with due sincerity. In presenting our own experi-ence, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go. Safety work in some form has been carried on in and about the mining properties of The Union Pacific Coal Co. since the first mine was opened at the now long-abandoned town of Carbon, Wyo., in 1868. On June 30, 1903, an explosion and subsequent mine fire occurred in mine No. 1 at Hanna, taking 169 lives, and a second explosion occurred in tile same mine on March 28, 1908, in which 59 additional lives were lost. Looking back with impartiality on the causes leading up to these two unfortunate disasters, we can only conclude that shooting from the solid, the absence of adequate ventilation, rock dusting, the use of water at the face to allay

Jan 1, 1938

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported J, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simplification to determine an economically feasible procedure that mould require a minimum of expensive equipment for plant erection and a minimum of regent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth Mile to utilize available facilities in a search for difficulties, that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 rounds per day of metal and operated under simulated -plant practice.

Jan 1, 1938

By H. J. Hand

STATISTICAL methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,' written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science,, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should .they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. † Many Useful Statistical Devices Available.-Many statistical methods of attack are available for the analysis of plant data. It is the object of this paper to discuss applications of some of these methods to the solution

Jan 1, 1938

WHY IS IT that smoke-abatement efforts do not bring more satisfactory results? The main reason is an incorrect estimate of the kind and size of the job. When an industrial community realizes that keeping the air clean is a project of similar magnitude to keeping streets clean, providing clean water, removing city waste, or guarding the moral atmosphere, then there maybe a real hope of success. We usually think of the project in too small terms. It is thought of as is the dog catcher or the boiler inspector--a matter of a man or two, a job or two, a small appropriation of variable and uncertain amount, to be abolished in a fit of economy and reestablished under pressure of a vigorous minority. Even so, it is surprising how much is obtained for the effort; but the community is rarely satisfied, for the job is bigger than it was conceived to be. Continuous, never-ceasing effort is required to clean up a smoky city. A few months of relaxation and the situation slips back some years of effort.

Jan 1, 1938

Jan 1, 1938

By Will H. Coghill, Fred D. DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force[+] of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub- sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

Jan 1, 1938

Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress -appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions end hearings2/ relative to the need for the survey, the opinion was expressed that crude oil held is storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to

Jan 1, 1938

By H. M. Day, C. H. Mathewson

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy' in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in. the right region. PREPARATION OF ALLOYS The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By E. T. Knight, John D. Gill

Much has been written and said concerning the alleged wasteful and uneconomic use of natural gas and petroleum. Espccially condemned has been the use of natural gas for the production of carbon black and the use of heavy fuel oil under steam boilers.' The critics of these usages of gas and oil have sought to make effective their verbal attacks on the industry by the repetitive expression of the words "inferior" and "superior" uses2 of petroleum. Thus, to employ natural gas for residential heating was to use it in a superior way; to use it for the production of carbon black was to use it in a wasteful and uneconomic way. To use petroleum for the production of automotive fuel was to use it in a superior way; to employ it as a residential fuel and as the prime source of power in an industrial plant was to use it in an inferior and uneconomic way. No doubt the objections to such employment of gaseous and liquid natural hydrocarbons originated in the belief that natural gas and petroleum are limited, nonregenerative mineral resources, and that the functions they perform can be just as well performed by other natural resources like coal13 of which practically unlimited reserves are known. The generations that have dominated each of the last four decades have counted reserves4 of petroleum in terms of a few years supply. Meanwhile, domestic demand for motor fuel rose spectacularly from a few million barrels in 1900 to more than 500,000,000 bbl. last year.5 The more imaginative and vocal critics drew startling word pictures of the catastrophe of 25,000,000 motor vehicles made useless and of the great automotive manufacturing and allied industries brought to an untimely end, and millions of workers left hopelessly unemployed by what they called the deplorably rapid depletion of the petroleum reserve. Many of the critics have been sincere advocates of the conservation of natural resources; many others, and in recent years probably the majority, have espoused the doctrine of conservation to promote their own self-interest rather than that of the public. The latest advocate of severe restriction in the use of petroleum for the alleged purpose of conserving the petroleum resource proposes to achieve that end by a bill,6 now before

Jan 1, 1938

By H. l. Burghoff, D. E. Lawson

The presence of tellurium in copper and, by inference, in copper alloys, has been considered seriously detrimental and has been avoided. In particular, very small amounts of tellurium have been found to produce red-shortness, although the effects on cold-working and ordinary physical and mechanical properties have not been known so definitely. References in the literature are few, but as long ago as 1881, Eglestonl reported that 0.083 per cent tellurium in fire-refined copper rendered the copper red-short and therefore worthless for hot-rolling. In hot-rolling copper cakes containing this amount of tellurium, he found that fine cracks appeared in the cakes on the first pass through the rolls, the cracks opening further in successive passes. When cold, the metal was said to be tough and malleable. A few years ago, during the course of an investigation in our laboratory on copper-base alloys, it was found that tellurium-bearing alloys could be machined much more freely than similar alloys not containing tellurium. The study was pursued further in this direction, and considerable data were obtained, which indicated that certain tellurium-bearing alloys might have properties of commercial interest. The work eventually led to patent protection,2 a wide range of tellurium-bearing copper-base alloys being covered. This article presents results obtained on the effect of tellurium on the mechanical properties of three copper-base alloys: commercial bronze (90 Cu, 10 Zn), 1.5 per cent tin bronze (98.5 Cu, 1.5 Sn), and silicon bronze (96 Cu, 3Si, 1 Zn). Several alloys were cast in each series, with tellurium content ranging from 0 up to about 1 per cent. The alloys were melted under charcoal in a clay-graphite crucible, using a high-frequency induction furnace, and were cast without undue difficulty in rod form, 15/8 in. in diameter. Charges for the zinc and tin series were made up from the following materials: cathode copper, electrolytic zinc, tin, and tellurium in slab

Jan 1, 1938

By L. C. IlsLey

The cool drills that have received the approved of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3363, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.

Jan 1, 1938

[ ]

Jan 1, 1938

By David Segura

THE Huitzuco mercury deposits have been described by C. W. Vaupell,1 therefore the general information such as location, history, production, etc. will not be repeated here. The present owners acquired the property when the deep levels of the Cruz mine were flooded, and it was believed that a relatively large tonnage of low-grade ore and fills would be encountered in the flooded section, because of the early mining methods used in the Cruz mine. The mine was partly unwatered and about 187,000 tons of fills was pit-sampled in the San Cayetano stope. These fills average 2.4 kg. Hg per ton. During the period of maximum production at Huitzuco, the ores were sorted in the mine and cobbed into 3-in. pieces, which were treated in Scott furnaces. Large pieces of raw ore are found in the sinter, and it is indicated that both recovery and costs were not very satisfactory. Recent practice has been to treat the ores in closed retorts made of 10-in. pipes. Because of the presence of combined antimony in the mineral livingstonite (HgS.2Sb2S3) and considerable native sulphur, little or no metallic mercury is recovered in the condensers and a second retorting of the condenser muds is necessary. This makes the treatment of the ores expensive and tends to low recoveries of mercury. The principal costs of retorting are, in their relative order: (1) fuel, (2) low recovery of mercury, (3) replacement of retort pipes, (4) labor. METHODS TESTED Three series of experiments have been made, with the object of reducing the costs of recovering mercury and antimony from the ores, by: (1) wet metallurgical methods, (2) bulk roasting in large mechanical furnaces, (3) concentration to reduce the bulk to be followed by roasting in some mechanical furnace. The wet metallurgical methods did not appear feasible because of the high cost of the alkaline solvents used, and investigations of these were not carried beyond the preliminary stage.

Jan 1, 1938

[ ]

Jan 1, 1938

By A. H. Taitt

The original basis for the search for oil in Great Britain was described last year.t During 1937 the exploratory drilling by the D'Arcy Exploration Company, Ltd. has been continued. Three wells have been completed in the south of England and a fourth is nearing completion. In addition, test wells are now being drilled in Scotland and East Yorkshire. Southern England The test well on the Portsdown structure, which at the end of 1936 was drilling in the Lower Lias at 5792 ft., entered the Triassic at 6540 ft. and was completed in that formation at a depth of 6556 ft., without encountering further indications of petroleum. The Henfield well encountered the Lias at a depth of approximately 4090 ft., and after drilling 800 ft. of an argillaceous development of that formation entered a series of marls, breccias and conglomeratic limestones of the Carboniferous. Drilling was suspended at a depth of 5105 ft., in the latter formation. The consistently impermeable nature of the strata encountered in the Portsdown and Henfield test wells focused attention on the desirability of obtaining shore-line conditions of the Jurassic. With this end in view the Kingsclere anticline, a few miles south of Newbury in Berkshire, was selected for a next test. The Kingsclere well has now reached a depth of 5032 ft. in the Lower Lias and has encountered a full development of the Jurassic. With the exception of the Portland sand, which has a slightly greater porosity, and the Corallian, in which relatively great thicknesses of impervious limestone were met, conditions of sedimentation have been found to be comparable with those of the earlier wells. Small traces of petroleum have been found in cuttings and cores, but formation tests carried out at frequent intervals have yielded no flow of oil. In order to test the Corallian, from which series an outcropping oil sand had been found, a test well was drilled in a near-by anticline at Poxwell in Dorset. The Poxwell well started in the Portland beds and entered the Corallian at 995 ft. The sands at the horizon of the out-

Jan 1, 1938

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938