Search Documents

By Fred C. Bond, Fred T. Agthe

When some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material. and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media during normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many commercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an important one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain laboratory tests were made from which it was found that different materials form coatings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qualities, like coal and graphite. In general, the softer materials tend to coat at coarser sizes than the harder or more brittle materials. Limestone, as an example, will coat more readily than quartz, even though limestones of different- texture and composition exhibit great differences in coating potentialities. Various materials were tested in the laboratory to show the variation in coating qualities. It was found that in most tests quartz must be ground to a fineness that would permit it to pass through 325 mesh before coating became markedly detrimental to the grinding operation. Siliceous rocks, however, tend to coat more readily than quartz. Granite, which is composed essentially of feldspar, quartz and mica, has been found to start coating at about 92 per cent through 200 mesh, and feld-spathic minerals alone usually show a tendency to coat at the same fineness. Barite has been ground in the laboratory to a fineness of 99 per cent through 325 mesh without showing serious coating of the grinding media. Gypsum coats readily. Apatite and phosphate rock usually tend to coat. Hematite usually coats, although when mixed with charcoal it does not do so. In testing the carbonate rocks and minerals, it has been found that burned magnesite, dolomite, and dolomitic limestone coat, whereas calcite and calcined calcite do not coat so readily. It has been found that commercial glass, slate, talc, steatite and coke have little tendency to coat. The relative tendencies toward coating during grinding operations, exemplified by

Jan 1, 1943

Jan 1, 1943

DAVID THOMAS 1871 R. W. RAYMOND 1872-1874 A. L. HOLLEY 1875 ABRAM S. HEWITT 1876 T. STERRY HUNT 1877 ECKLEY B. COXE 1878-1879 WILLIAM P. SHINN 1880 WILLIAM METCALF 1881 RICHARD P. ROTHWELL 1852 ROBERT W. HUNT 1883 JAMES C. BAYLES 1884-1855 ROBERT H. RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B. POTTER 1888 RICHARD PEARCE 1889 ABRAM S. HEWITT 1890 JOHN BIRKINBINE 1891-1892 H. D4. HOWE 1893 JOHN FRITZ 1894 J. D. WEEKS 1895 E. O. SPILSBURY 1896 THOMAS M. DROWN 1897 CHARLES KIRCHHOFF 1898

Jan 1, 1943

By George M. Fowler, R. E. Illidge

Part I. Developing BY GEORGE M. FOWL INTRODUCTION The Tri-State district comprises an area of about 2000 square miles in southwestern Missouri, southeastern Kansas, and north [ ] eastern Oklahoma. The part that is in and contiguous to Missouri is still sometimes designated as the Joplin district (Fig. I). EARLY OPERATIONS Mining operations in what is now the Tri-State district date from about 1848 and have been continuous to the present. Apparently the first discoveries of ore were made about the same time near the present sites of Joplin, Oronogo, and Granby. Lead minerals were found at grass roots, probably in shattered rock in shallow excavations, then these minerals were followed in shear zones to deeper horizons. The mining of zinc followed. Before 1874, zinc ore was worthless and discarded as waste. According to published records, the total production of lead to that date was 49,000 tons of metal from 70,000 tons of concentrates. PRODUCTION The aggregate ore production from the Tri-State district was recorded at interval

Jan 1, 1943

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By G. L. Craig

In order to meet the unprecedented demand for copper it has proven necessary not only to develop every primary source, but also thoroughly to exploit the vast reservoir of metal in use that is not directly serving the war effort. To accomplish this, industry has been called upon to use its resourcefulness for developing methods of recovery that have not been previously utilized. It is in this connection that we have been asked to review the methods suggested for recovering the basic constituents of various types of the so-called clad or composite steels. As a background for a discussion of recovery processes, it seems appropriate to consider clad materials in general and their processes of manufacture. A composite steel has been defined as one consisting of two or more component parts of which the smallest shall comprise at least 3 per cent of the total mass. Clad materials or composites are produced commercially by several different methods of which the most important may be classified as: I. The Blacksmith or Forge Weld Method. This method is limited to carbon steels or low-alloy steels as the presence of even small amounts of common alloying metals prevent the formation of a satisfactory weld. The principle is the application of pressure to sections in contact at elevated temperatures. Because of the tendency of the iron to oxidize, borax is generally used as a flux to absorb the iron oxide. 2. Casting Process-In this method a composite ingot, billet or cake is produced by pouring one metal onto or about another. The bond may be accomplished by the action of the molten metal against a solid, in which case the bond may be referred to as mechanical; while in other instances alloying occurs at the interface producing an anchor by the formation of component parts of the two materials. 3. Cementation Process.-In this process any number of combinations of metallic and nonmetallic constituents which are mixed together may be used as a bonding agent. The combinations, whatever they may be, are placed between the materials to be joined and subjected to pressures at elevated temperatures to produce the desired bond. 4. Fusion Welding Processes.-Gas and electric joining for direct use or subsequent fabrication. 5. The, Assembly Process.-This method involves the joining together of prefabricated bars or plates followed by hot and/or cold working the assembly to the desired finished form. This method is advantageous in many cases because of its flexibility on small quantities as compared to the casting method. It is also possible to control the relative proportion of components more accurately. In this discussion we are concerned only with the scrap resulting from the manufacture of clad materials and our interest,

Jan 1, 1943

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

Jan 1, 1943

By E. C. Carris

THE particular field of application of machines utilizing air cur¬rents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 12,000,000 tons of bituminous coal were cleaned by air machines during 1940. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful com¬mercial pneumatic oscillating machine for cleaning bituminous coal in 1916, by the Sutton, Steele and Steele Co., Dallas, Texas, and the Ameri¬can Coal Cleaning Corporation, formerly of Welch, W. Va., four other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine, 1924. 2. Arms "Concentrator," oscillating table, 1924. 3. Heyl and Patterson oscillating table, 199.7. 4. "Stump Air-Flow," pulsating air jig, 19391. Out of these five developments only the Sutton, Steele and Steele, or American Oscillating, and the Stump Air-Flow Jig remain on the market. They are the predominating pneumatic coal-cleaning machines in use in the United States. HISTORY OF AMERICAN TYPE SEPARATOR The first successful American machine, the CJ table (Fig. 1) was developed by the Sutton, Steele and Steele Co. The SJ table was the first standard model designed specifically for the cleaning of coal. It was installed in the original Crane Creek plant, owned and operated by the American Coal Co. at McComas, West Virginia. This plant was designed by The Roberts and Schaefer Co., Chicago, Ill., working in cooperation with the American Coal Cleaning Corpora¬tion, which had taken over the patent rights and sale of the pneumatic separators. Eight machines were installed in this plant. They were known as the type SJ. They were 60 by 84 in., the short dimension being the width of

Jan 1, 1943

By J. W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By Earl S. Greiner, Eric R. Jette

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. 'This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,' who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are presented in some detail. Basic principles ,are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and on form, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance cones and jigs are usually dispensed with, and other methods, such as the Hydrotator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh. In assuming this variable upper limit of particle size in a coal slurry, it is recognized that the size ranges discussed will duplicate sizes dealt with

Jan 1, 1943

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company's discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By A. A. Smith, J. S. Smart

THE elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses, When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range 0 to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorily determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing and oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B. and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold, The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300° and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type, All samples were quenched from the annealing temperature in 10 per cent H2SO4 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.1 EFFECT OF SILVER Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By T. H. Miller

THE CHAIRMAN.-This session has to do largely with the question of specifications and conservation as regards secondary metals produced from scrap. We are all familiar with the many varieties of scrap metals and the astonishing number of secondary metals of various specifications produced from the treatment of those scraps. The impact. of the war on this industry has required a great many changes in the types of secondary metals produced from scrap, and in their utilization. In the short period available we cannot cover very much of this field, but we do hope to give you through the various papers a brief introduction to some of the principal problems. Mr. James S. Earle will present the first paper. Mr. Earle:

Jan 1, 1943

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE studies of the mechanism of precipitation and of the resulting property changes in aluminum-silver alloys1-3 have presented some new concepts of the aging reaction-concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.1,4 These platelets grow in lateral dimensions and in thickness with aging time until they are thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstätten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuous precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 EXPERIMENTAL PROCEDURE The alloys were made using 99.97 per cent Al or distilled magnesium, with

Jan 1, 1943

By C. M. Romanowitz, H. A. Sawin

Placer dredging as we know it today, especially gold dredging, is an industry about 40 years old, dating from the beginning of this century, when a few mining men in California saw the possibilities in adapting earlier dredging methods to California placer fields in and immediately adjacent to streams. At first it was thought that dredges must be operated in existing stream beds, but experience soon pointed the way to dredging alluvial deposits of old stream beds, operating on landlocked dredging ponds. Within the first five or six years of modern dredging, experience was gained so rapidly that dredges to dig 60 ft. below water level were *designed and built. This depth was believed by many operators to be the maximum at which successful dredging could be carried on. Alluvial deposits of gold, suitable for dredging, were readily handled by equipment available and developed early in the industry's history. Much of the gravel was easily dug and if deposits were cemented, contained large boulders, or for some other reason could not be handled by a dredge, the ground was abandoned in favor of other deposits that could be handled easily. Many failures, adversely affecting the dredging industry, resulted from attempts at that time to extend the scope of placer dredging with equipment not suited to the formation being dredged. Dredging ground suited to early equipment was exhausted eventually, but many supposedly undredgeable alluvial fields containing gold in commercial quantities were found and became known to dredgemen. Improved equipment was needed to work deposits known to exist at great depths or associated with unusual obstructions. Operating companies looked to dredge manufacturers and metallurgists, particularly manganese-steel foundries, for improved designs and materials. Experience developed in California has spread throughout the world, and dredges of improved types have been adapted to the mining of platinum and tin as well as gold. Space will not permit a description of all the improvements in dredging since the early days, but a few of the recent developments are worthy of note, because they make possible the dredging of placer deposits of great depth, those having hard, irregular bedrock or containing large boulders in great quantities, and compacted or cemented gravel deposits. Deep Dredging At Hammonton, calif., yuba consolidated Gold Fields has, within= the past two years, built its dredge No. 20. The company has operated continuously in that field since 1904, digging successively at maximum depths of 60 ft., 80 ft., 112 ft., and now 124 ft. below water level. The first dredges were equipped with buckets of 6 and 7½-cu. ft. capacity; six dredges operating in the field today have 18-cu. ft. buckets, digging now 65 to 124 ft. below water level. Some ground near Hammonton has been dug for the third time, owing to the devel-

Jan 1, 1943

By Earl S. Greiner, Eric R. Jette

The constitution of the iron-rich iron-nickel-silicon alloys at 600ºC. has been determined by X-ray crystal structure methods. If the results are represented isothermally by a conventional equilateral triangular plot, the single-phase solid solution (body-centered cubic structure) of the iron-rich alloys at 600°C. is bounded by four two-phase areas. Three three-phase areas separate the respective two-phase areas. Three of the phases in the polyphase areas have the same structures as the corresponding phases in the binary iron-nickel or iron-silicon alloys. There are two phases, however, that have not been reported previously and whose structures have been tentatively identified in the present investigation. The solid solubility limit of the iron-rich solid solution at 600°C. was determined by comparing the lattice constants of this body-centered cubic phase in the single and polyphase areas. It has been shown that the lattice constants of ternary alloys may be represented by surfaces whose distances above the ternary plot (representing atomic composition) are proportional to the lattice constants of the respective alloys. Then the intersections of the surface for the single-phase alloys with those for the corresponding phase in the polyphase alloys, at the respective temperatures, are the solid solubility limits of the single-phase alloys at these temperatures. The data of the present investigation were evaluated by this method, although by a system of orthographic projection it was possible to represent the three-dimensional model in two-dimensional diagrams. This investigation has shown that the solid solubility of nickel in the body-centered cubic phase of the iron-rich iron-nickel-silicon alloys at 600°C. changes from 3.7 weight per cent (Owen and Sulley) in the binary iron-nickel alloys to 5.0 per cent in the ternary alloys containing 4.8 per cent silicon. Further additions of silicon increase the solid solubility limit of nickel to 16.0 per cent at 12.6 per cent silicon. From this point the limit decreases to 9.5 per cent nickel at 15.5 per cent silicon and is, of course, zero at 15.3 per cent silicon in the binary iron-silicon alloys.

Jan 1, 1943

By Frederic Benard

This paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel colltent is low enough to permit the slimes to proceed to the dorè furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfartory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. . It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1943