Search Documents

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By Walter S. Weeks

IN this paper the effect of natural ventilation pressures is considered a part of the mine resistance and it is shown that their effect on the mine resistance is not the same as the total natural ventilation pressure of the shafts if the mine has several levels. It is shown that increasing the fan pressure causes the division of the air to approach the condition that would obtain if there were no natural ventilation pressure present. It is shown that if an appreciable difference in pressure is maintained between the beginning and end of a group of splits, the value of the integrated effect of the natural ventilation pressures on the individual splits does not change substantially with moderate changes of this pressure. A method is outlined for determining the resistance factor of the mine and the value of the effect of natural ventilation with the fan operating; also a method for determining this factor when circulation is caused by natural ventilation alone. NATURAL VENTILATION PRESSURE Natural ventilation pressure (N.V.P.) is caused by the difference in weight of the air in two similar columns between two horizontal planes, and the difference in weight is caused principally by the difference in temperature of the two columns. The fan pressure causes some variation in density, but, since it is usually small and affects both columns, its effect is relatively unimportant. It has been suggested that "N.V.P." be called "stack effect"; but, since the term N.V.P. was used in a previous Institute paper,' applied in exactly the same manner, the term will be used. FRICTIONAL RESISTANCE The frictional resistance to flow in a mine without natural ventilation may be expressed as RQ2 where R is a constant for a given air density and Q is the rate of flow. This frictional resistance plus the effect of velocity changes will be called the F pressure (F.P.) and a curve of F.P. against Q, the F characteristic of the mine. If a pressure is applied to a mine by a fan, the air flow so adjusts itself that the drop in pressure through any path from entrance to exit of mine, due to frictional resistances and velocity changes, is the same as that in any other path. The mine resistance varies as the square of the quantity. The air distribution without N.V.P. will be called "normal." NATURAL VENTILATION PRESENT When N.V.P. is irregularly distributed in a mine, it is more convenient in analysis to consider the N.V.P. as a part of the duct resistance. If it is so considered the resistance no longer varies as the square of the quantity, and if N.V.P. exists between levels the distribution of the air is no longer normal. The total N.V.P. of the mine is the pressure caused by the full length of the shafts. If a mine has several levels, N.V.P. exists

Jan 1, 1944

By C. J. Bier, J. F. O?Keefe

THIS study was carried out with copper because it represents the simplest form of sintering, in that but one metal is involved and all reactions occur in the solid state. [ ] The present work will cover three variables affecting the sintering process; namely, briquetting pressure, sintering temperature and time in hot zone. Although strength and dimensional changes were observed, this is primarily a metallographic study of the sintering process in copper. The term "sintering" should be understood to mean the process by which the metal powder particles of the compact become united into one body. MATERIAL USED The copper powder used was made from reduced copper oxide, and is typical of a grade used for the mass production of parts formed of metal powders. The screen analysis of the powder was as follows: [ ] The minus 325-mesh analysis was made by using a Roller Air Analyzer.1,2 The apparent density is here defined as the weight per cubic centimeter of the [ ] loose, unpacked powder as measured with the Hall flowmeter. The value for the powder used was 2.57 grams per cubic centimeter.

Jan 1, 1944

THE metal iron has physical and chemical properties which are somewhat different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron, the former being the ordinary form at room temperature. When heated above the "A2 point," 1400°F. (760°C.), the metal becomes non-magnetic, and at the "As point," 1670°F. (910°C.), it undergoes a change in crystalline form to become gamma iron. In the range 1400 to 1670°F., it is sometimes called beta (0) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 2550°F. (1400°C.), it changes into delta (d) iron, which is identical with beta or non-magnetic alpha iron. Pure iron melts (in a hydrogen atmosphere) at 2795°F. (1535°C.); the melting point is generally lowered by alloys or impurities. PROPERTIES OF IRON AT HIGH TEMPERATURES Many of the properties of iron undergo abrupt changes at the transition temperatures. (1) For example, in heating through the As point a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 27 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly within the range of stability of a given form, but this is not always the case. For example, the specific heat reaches a sharp maximum at the A2 point although no transformation occurs. Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals which are liquid at the melting point of iron only lead, silver, and bismuth refuse to dissolve to an appreciable extent. The non-metals presumably dissolve by virtue of the formation of an iron compound; for example, sulphur is thought to dissolve as the compound FeS. However, there is no satisfactory method of proving that this

Jan 1, 1944

By McHenry Mosier

Mercury is one of the strategic metals the supply of which has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributes substantially to increased production of mercury in the United States and to consequent accumulation of Governments stock. Other contributing factors were higher prices for mercury and Government loans to operators. The Bureau has undertaken 15 exploration projects, 13 of which have been completed. This work comprised 40,307 feet of drilling arid 35,082 linear feet of sure ace trenching and has indicated commercial ore containing 37,400 flasks of mercury and marginal ore contain¬ing 29,200 flasks - a total of 66,600 flask , equivalent, respectively, to domestic production at 50,000 flasks per year for 9 months , 7 months, and 16 months. Early in 1944, as Government stocks had become adequate, domestic production was gradually curtailed cancellation of Government contracts for the purchase of mercury and Government control of labor and operating supplies.

Jan 1, 1944

By A. T. Sweet, C. E. Plummer, H. W. St. Clair, S. F. Ravitz

The ammonium sulphate process for recovering alumina from clays was proposed by Rinman, Buchner, and others many years ago, and more recently various modifications have been investigated both here arid abroad.l-Is The process, as it is being investigated by the Bureau of Mines, involves the following essential steps: (I) sulphating the alumina in the clay by baking with ammonium sulphate at approximately 4m°C., (2) leaching with water to extract aluminum sulphate and ammonium sulphate, (3) crystallization of ammonium alum, (4) conversion of the alum to aluminum hydroxide by the ammonia gases given off during the baking, and (5) calcining the aluminum hydroxide to alumina. The over-all reaction between kaolinite (the most important alumina mineral in most clays) and ammonium sulphate during the baking step may be expressed as follows: Al2O8.2SiO2.2H2O + 4(NH4)2SO4 = (NH4)2SO4.A12(SO4)3 + 6NH3(g) + SH2O(g) + 2SiO2 [i] There is definite evidence. as is shown later. that the aluminum occurs in the baked product as anhydrous ammonium alum rather than as aluminum sulphate, provided the baking temperature is not much above 4o0°C. It is probable that the reaction takes place in the following steps: (NH4)2SO4 = NH3 -(- NH4HSO4 [2] Al2O3.2SiO2.2H2O + ;}NH4HSO4 = A12(SO4)3 + 3NH3 + 5H2O + 2SiO2 [3] A12(SO4)3 + (NH4)2SO4 = (NH4)2SO4.A12(SO4)3 [4] In onc modification of the process, the ammonium sulphate is first decomposed according to Eq. z, and the clay is treated with the resultant ammonium acid sulphate. Reaction I is highly endothermic. On the basis of the best available data, the following values have been estimated for the changes in heat content and free energy in calories per mol: -AH = 331,040 - 34T -AF = 331~040 - 78.3T log T - 671.8T The heat required' at 25OC is 320,900 cal. per mol, or 5650 B.t.u. per pound of alumina. The theoretical equilibcium pressure of NHa, based on the free-energy equation given above, increases very rapidly as the temperature rises above 3o0°C., and reaches one atmosphere at 43s°C. Ammonium alum solutions are almost ideal for crystallization. A saturated solution of ammonium alum contains 126. grams of AlzOa per 1000 grams of water at 90°C. and only 16.5 at 20 C. Hence most of the alum crystallizes out when the

Jan 1, 1944

By F. R. Archibald, F. C. Jackson

The. prospect of winning aluvinum from clay was recorded almost a century ago at a time when the metal was no more than a curiosity.$ As the industry developed, and it has probably developed faster than that of any other metal, the expanding need for raw materials was adequately met by the ample supplies of bauxite ore. As with the other metals older in industry, however, lower grade ores have gradually entered the raw-material field through improvements in ore dressing, insufficienoy of high-grade ore supplies, favorable geographic location, or national necessity for domestic supply. So with aluminum, or alumina, which has been established as the requisite intermediate, the time may have come when a satisfactory process, with favorable location and suitable raw materials, can hold a sound place both in metallurgy and economics. It is the purpose of this paper to describe the Ancor process and its proposed application in treatment of clay in a plant now under construction at Harleyville, South Carolina, by the Defense Plant Corporation. Development of the AncoR Process The Ancor process has developed through successive stages of laboratory investigation, pilot-plant demonstration using neph-eline syenite and pilot-plant demonstration using kaolin-type clay from South Carolina, and is now in preparation for unit trial on an operating plant basis using the latter material. The laboratory studies were carried out over a number of years in the laboratory of the American Nepheline Corporation in Rochester, N. Y., and for the same company in the ore-dressing laboratory of Beattie Gold Mines, Que. Ltd. at Dupar-quet, Quebec. Both companies are associated with Ventures Ltd., Toronto, and its associated American companies. The work was originally undertaken with a view to recovery of alumina and alkalies from nepheline syenite as an adjunct to the American Nepheline Company's established business in the glass and ceramic trades, but as a process developed the possibility of application to clay and other aluminous raw materials became apparent and the laboratory studies were broadened to include these as well. Under the more pressing impetus of wartime needs and possibilities, pilot-plant operations were undertaken at the Canadian Bureau of Mines Ore Dressing Laboratories in Ottawa, and for purposes of demonstration under joint sponsorship of the Canadian Bureau of Mines, The American Nepheline Corporation, and The Aluminium company of canada Ltd. Upon completion of this program, of

Jan 1, 1944

By F. R. Archibald, C. F. Jackson

THE prospect of winning aluminum from clay was recorded almost a century ago at a time when the metal was no more than a curiosity.? As the industry developed, and it has probably developed faster than that of any other metal, the expanding need for raw materials was adequately met by the ample supplies of bauxite ore. As with the other metals older in industry, however, lower grade ores have gradually entered the raw-material field through improvements in ore dressing, insufficienoy of high-grade ore supplies, favorable geographic location, or national necessity for domestic supply. So with aluminum, or alumina, which has been established as the requisite intermediate, the time may have come when a satisfactory process, with favorable location and suitable raw materials, can hold a sound place both in metallurgy and economics. It is the purpose of this paper to describe the Ancor process and its proposed application in treatment of clay in a plant now under construction at Harleyville, South Carolina, by the Defense Plant Corporation. DEVELOPMENT OF THE ANCOR PROCESS The Ancor process has developed through successive stages of laboratory investigation, pilot-plant demonstration using nepheline syenite and pilot-plant demonstration using kaolin-type day from South Carolina, and is now in preparation for unit trial on an operating plant basis using the latter material. The laboratory studies were carried out over a number of years in the laboratory of the American Nepheline Corporation in Rochester, N. Y., and for the same company in the ore-dressing laboratory of Beattie Gold Mines, Que. Ltd. at Duparquet, Quebec. Both companies are associated with Ventures Ltd., Toronto, and its associated American companies. The work was originally undertaken with a view to recovery of alumina and alkalies from nepheline syenite as an adjunct to the American Nepheline Company's established business in the glass and ceramic trades, but as a process developed the possibility of application to clay and other aluminous raw materials become apparent and the laboratory studies were broadened to include these as well. Under the more pressing impetus of wartime needs and possibilities, pilot-plant operations were undertaken at the Canadian Bureau of Mines Ore Dressing Laboratories in Ottawa, and for purposes of demonstration under joint sponsorship of the Canadian Bureau of Mines, The American Nepheline Corporation, and The Aluminum Company of Canada Ltd.

Jan 1, 1944

By L. L. McMurray

ILMENITE is the most important raw material for manufacture of titanium dioxide.1 Industrially, several other products are made from ilmenite, the most important of which are: ferrotitanium, ferro carbon-titanium, copper-titanium, titanium carbide and titanium nitride. The production of titanium metal is still in the laboratory stage because of the difficulty of extraction and as yet no important application for the metal has been found. Ilmenite has received considerable attention as an industrial raw material. Imports of ilmenite concentrates for the first nine months of 1941 were 156,737 short tons, the chief source being Travancore, India.2 Domestic production of ilmenite has here-tofore been confined to Amherst and Nelson Counties, Virginia, where a complex rutile, ilmenite, and apatite ore is mined and treated to utilize all three of these minerals. A recent report3 has described development of the large titaniferous magnetite ore body at Tahawas, New York, where it is expected that 800 tons of ilmenite concentrates, containing 48 per cent Ti02 will be produced daily. Additional domestic production is expected from a large ilmenite deposit recently opened in Caldwell County, North Carolina. Flotation tests indicate that a high-grade concentrate containing 53 per cent Ti02 can be made from the North Carolina ore. Prospecting of domestic ores in other areas has been reported.4 It appears that increased domestic production of ilmenite may well save considerable shipping space so vitally needed in these times. The composition and chemical structure of pure ilmenite is given by Dana as: FeO, TiO2; Ti, 31.6 per cent, Fe, 36.8 per cent, 02, 31.6 per cent. This composition is variable in that some iron or titanium may be replaced, giving a variable iron-titanium ratio. As an example, the iron-titanium weight ratio of ilmenite in Caldwell County, North Carolina, has been determined to be 0.94 (using 97.1 per cent ilmenite concentrate obtained by heavy liquids on minus 150-mesh ore) compared with theoretical 1.16. No rutile was noted in this ore to account for the low value. This North Carolina ore is free of magnetite, which is a common associate of ilmenite ores. In view of a large potential production from North Carolina, the Tennessee Valley Authority conducted a study of methods of concentration of that ore, of which the results are reported herein. THE ORE Five samples of ore were taken from the deposit at various exposed locations and were mixed for the study and testing. An attempt was made to proportion the amount of weathered and unweathered portions in making the composite sample, so as to approximate actual operating conditions. An examination of representative specimens of the sample showed the following general facts: I. The black mineral comprising nearly 70 per cent of the ore is ilmenite.

Jan 1, 1944

By J. C. Hartley

The most important single operation in mining is the ventilation of underground areas in a manner conducive to the health and safety of employees. Adequate volumes of pure air must be supplied at the working faces, along the haulageways, and wherever men work, so as to dilute and carry away the methane liberated from the coal and adjoining strata, noxious gases evolved by the use of explosives, and the carbon dioxide exhaled by men and formed by oxidation of carbonaceous material, as well as any other gases, and also dusts which may be found in mine workings. A sufficient quantity of air must also sweep abandoned or worked-out areas of the mine to prevent the accumulation of gases, where sealing methods are not utilized to isolate old workings. Air, in a quantity adequate to meet the needs of the particular mine to which it is applied, is necessary, and supplying it can be made very expensive through failure to observe good practices in its direction and apportionment." Leaky stoppings, doors, and overcasts rob the working faces of air and add to the ventilating cost by burdening the fans with fugitive air,

Jan 1, 1944

By J. Murray Riddell, George A. Morrison

THIS paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.[+] Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Barberton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 20-40 ft. Fractured. sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), 3/8 by 4 by 4-in. angle irons; spacing of sets, 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. THE SHAFT-SINKING OPERATION The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (I) a storage pocket of 300 cu. ft. capacity with truck servicing facilities, and (2) pneumatically operated dump doors, which were actuated by the hoistman, thus caring for the dumping of the "ball-and-chain"

Jan 1, 1944

By Frederick N. Rhines

Because of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding their occurrellce, even though the fundamental mechanisms invalved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by Processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpiet the next. It is the purpose of the present Paper to present, by means of examples drawn from practice, a brief survey of the ways in which gas-metal diffusion serves and obstructs the Purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with ' but brief mention of parallel cases. The Nature of Gas-metal Diffusion The term ugas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of " substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain.temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. NO element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.'' The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

Trans No. Place Date Vol. 1. Wilkes-Barre, Pa. May, '71 1 2. Bethlehem, Pa. Aug., '71 1 3. Troy, N. Nov., '71 1 4. Philadelphia, Pa. Feb., '72.. 1 5. New York, N. Y. May, '72 1 6. Pittsburgh, Pa. Oct., '72 1 7. Boston, Mass. Feb., '73 1 8. Philadelphia, Pa. May, '73 2 9. Easton, Pa. Oct., '73 2 10. New York N. Y. Feb., '74 2 11. St. Louis, Mo. May, '74 3 12. Hazleton, Pa. Oct., '74.. 3 13. New Haven, Conn. Feb., '75 3 14. Dover, N. J. May, '75 4 15. Cleveland, Ohio Oct., '75 4 16. Washington, D. C. Feb., '76 4 17. Philadelphia, Pa. June, '76 5 18. Philadelphia, Pa. Oct., '76 5

Jan 1, 1944

By F. Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimoniallead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1944

By H. I. Najarian

This paper is a companion piece to the description of the electrothermic process that begins on page 141. It will be confined to a brief story of the development. of the Weaton-Najarian vacuum condenserf at this plant, together with up-to-date design and operating data. The Josephtown smelter was designed primarily for production of zinc oxide. However, the development of a method for production of zinc metal had always been under consideration, and accordingly one of the original eight units of the elcctro-thermic furnaces built in 1930 was set up to produce metal. The design of this furnace was identical with that of the oxide furnaces except that in place of oxide tewels opening into oxide manifolds, conventional conical clay condensers—similar to condensers used in horizontal retort smelting—were installed around the periphery of the furnace and in several tiers vertically for condensing the zinc vapors. The early experimental work in trying to condense zinc out of the mixtures of zinc vapor and carbon monoxide gas from the electrothermic furnaces indicated that, while the gases from electrothermic smelting would condense in surface-type condensers, the formation of blue powder was excessive and condenser efficiency low. Furthermore, operating a large unit of electric furnace with several hundred small condensers, with attendant high labor cost and unfavorable operating conditions, did not appeal to us. We also realized that a single unit of surface condenser capable of condensing 12 torg tons of metal per day would be of huge dimensions and possibly difficult of control. So we took as our aim the development of a method whereby a single condenser unit of reasonable dimensions would condense zinc, in one step, from the large volume of gases that the electric furnaces produced. We set about searching for knowledge on zinc metallurgy and design of zinc condensers in particular. Our study of the prior art focused our attention on the oft-repeated statement by earlier experimenters, that the most efficient way to condense metallic vapors, such as zinc vapors, was to bring the vapors into "intimate contact" with molten metal; but the methods offered for securing this "intimate contact" in any practical manner left much to the imagination. We were handicapped by not having some-one on the Josephtown smelter staff who could lay claim to being an expert zinc metallurgist and could give guidance from actual experience on the practicability of various schemes that haunted our imagination. Laboratory Experiments However, we had an expert ex-steam engineer in the person of George I?. Weaton, manager of the Josephtown smelter, who had had long experience with steam-jet condensers and would reiterate his belief at every opportunity that the logical and the most efficient way to condense zinc would be with a jet-type condenser. We became intrigued by the possibilities of a zinc con-

Jan 1, 1944

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 9, Article I, of the Bylaws of the Institute (see page 62 and following pages). During 1934, sundry amendments were made for the purpose of improving the student relationship. Postgraduate students are now eligible; and associateship can be maintained, with the payment of the regular dues of $2 per year, for 18 months following graduation in June. With his regular dues, each Student Associate is entitled to receive during the year his choice of MINING AND METALLURGY, METALS TECHNOLOGY, MINING TECHNOLOGY, PETROLEUM TECHNOLOGY, or two "classes" of Technical

Jan 1, 1944

By E. L. Jones

THE concentration of tin in the tailing from Sullivan ore has been de-scribed by H. R. Banks, superintendent of the Sullivan concentrator, in a paper presented at the annual meeting of the B.C. Division of the Institute in October, 1941(1). The reduction of the concentrate EARLY EXPERIMENTAL WORK Experimental work on the smelting of Sullivan tin concentrate was done in Trail. Preliminary tests in the laboratory indicated that the concentrate could be successfully treated in an electric furnace. A small electro-thermic pilot plant was built and, at the same time, reduction tests were made in an oil-fired reverberatory furnace. Both types of treatment gave satisfactory results. It developed that no fluxes, other than those already in the ore and in the ash of the reducing agent (either coke or coal), were needed. By using an excess of iron, a complete recovery of the tin in the slag was obtained, but with 20 to 30 per cent iron in the tin. A counter-current treatment was thus indicated, viz., the primary slag was first treated with hard-head (iron-tin alloy) from the refining and final slag smelting, producing tin with 2 to 4 per cent Fe. This secondary slag was subsequently treated with scrap iron to produce tin-iron alloy, and a final slag low enough in tin to waste. By following this line of endeavour, a tentative flow-sheet was drawn up and a successful operation was established. Without resorting to electrolytic refining, a metal comparable in purity to standard tin was produced. Metallurgical results and operating costs were found to be very similar with an electric furnace or a fuel-fired furnace. 'However, electric furnace smelting was chosen because the furnace required was smaller, and because some doubt existed as to the cleaning of the final slag in the reverberatory furnace reduction.

Jan 1, 1944