Search Documents

By E. B. Olds, Burt. B. P.

THE mines of the Consolidated Coppermines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. [ ] The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 1 ½ miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1946

By S. H. Ash

The paramount responsibility of Government is to protect the general welfare. One of the chief functions of the Bureau of Mines is to investigate and publicize methods of increasing safety and efficiency in mining operations. In an industrial civilization, energy resources constitute the foundation of a sound economic structure (14).4/ Coal is only one source of energy, but it provides more than half the energy consumed in the United States.

Jan 1, 1946

By Blake M. Loring, Robert A. Colton

MeltiXg procedures for most metals and alloys usually include some provision for the control of oxygen, since this element frequently has some undesirable effect on the properties of the metal or alloy concerned. In the melting of the various bronzes, this is especially true, since oxygen can be introduced into the melt in a number of ways, most of which are difficult to control. In making bronzes from virgin materials, oxygen is usually present in the commercial grades of copper used; electrolytic fire-refined copper ingots usually contain from 0.02 to 0.05 per cent oxygen. When ingot metal or scrap bronze is used in the charge, oxides are almost always present to some degree. Under certain melting conditions and in certain types of melting equipment the atmosphere over the metal may be highly oxidizing. This, of course, may be desirable in the melting practice used, but is certain to introduce appreciable amounts of oxygen into the melt, and that may not be entirely desirable. From the foundry viewpoint oxygen may have several harmful effects on bronzes. The formation of excessive amounts of oxides may produce drossy metal, which, in turn, means dirty castings and a potentially high rejection rate. It is claimed, too, that oxides in the metal may combine with hydrogen to form steam and thereby produce porosity in certain of the bronzes. The presence of certain refractory oxides, such as SnOz, may be undesirable from the viewpoint of making machining difficult, or as possible stress-raisers in the metal matrix. It is often said that excessive oxide present in the liquid metal makes the metal run sluggishly. Since it appears impractical to try to control the amount of oxygen introduced into the metal beyond taking the economical limit of precaution about charging dirty scrap, it would seem' that control of the oxygen content of the liquid metal offers the most promising approach to this problem. This might be done by using slags, or covers, or by the use of some element or compound added to the melt to remove oxygen preferentially. Most aspects of this problem have been considered and considerable work has been done along these lines. A reconsideration of the problem is indicated, however, by the controversial nature of the evidence at hand, especially on the possibility of using a chemical deoxidizer to control the oxygen content of bronzes. Choice of Deoxidizer The choice of the chemical agent selected as a deoxidizer would naturally depend first on the alloy in which it is to ~he used: in this particular case the alloy is Navy gun metal. In Table. I are listed a group of elements that might be considered as deoxidizers for bronze, with some of their properties that should be considered in

Jan 1, 1946

By Walter T. Lewieki

"INTRODUCTION Numerous deposits of iron ore are found in Cherokee, Bartow, Floyd, and Polk Counties in northwest Georgia. The deposits are generally small and irregular in shape. The ore is usually referred to as ""brown ore"" and is predominately limonite. The crude or ""bank ore"" has to be washed and concentrated before being shipped.The proximity of the deposits to the Birmingham furnaces and a favorable freight differential permit the operation of many deposits that otherwise would be uneconomical. The district produced 413,468 long tons of brown-ore concentrates, averaging 45.53 percent iron in 1943.The necessity of developing additional iron-ore reserves for the war energeucy to supplement the production of the Birmingham district, prompted the Bureau of Mines to initiate exploration of the more promising northwest Georgia deposits. Thirteen properties in the four counties were explored during the program (fig. 1).HISTORY AND PRODUCTIONSeveral furnaces were operated in the district until the early 1900's, ranging from charcoal furnaces to more modern plants with capacities up to 50 tons of pig iron. No furnaces have operated for about 40 years, the product being shipped to Alabama and Tennessee.Bartow County iron mining is declining, although formerly it was the principal producer of the district. Most of the known merchantable ore deposits have been exhausted. For the past 3 years the Mitchell-Hodge mine has annually produced about 225,000 long tons of concentrates containing 46 to 43 percent iron and at present is the only large producer in Bartow County."

Jan 1, 1946

By W. A. West

ONE who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion of the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1946

By Donald W. Scott

GENERALLY speaking, there is nothing very difficult about taking good micrographs of photogenic thin sections or grains with a petrographic micro-scopecamera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. I[a]) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. I[b]) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this is an incorrect interpretation is evident by reexamining the micrograph of Fig. I[a]. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. is the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1946

By F. B. Plummer, I. W. Walling

Bastin and others have demonstrated the presence of sulphate-reducing bacteria in oil wells producing salt water. Analyses show that at 125°F. bacteria alone reduce sulphates in East Texas salt water by only 3 per cent in 30 days, forming principally hydrogen sulphide and sodium or calcium hydroxide. The hydrogen sulphide reacts with soluble iron compounds to produce iron sulphide in the absence of oxygen, and ferric hydroxide where oxygen and air are present. Where iron or other metals and iron sulphide are already in the water containing bacteria, I00 per cent reduction of the sulphates is complete in 30 days or less; where magnesium is present, reduction is complete in 15 days. The effects of changes in temperature, of different bactericides, and of concentration of bactericides on sulphate reduction are described in detail and illustrated by tables and curves. The significance of sulphate reduction on corrosive properties of oil-field water is briefly discussed. Chemistry of East Texas Oil-field Water The chemical composition of the water in the East Texas field salt-water disposal pits is shown in Table I. This salt water corrodes pipes, pumps, and steel tanks excessively, principally because of its content of oxygen, hydrogen, sulphide, and carbonic acid. The carbonates in the water when exposed to air tend to give up carbon dioxide and to precipitate calcium carbonate in large quantities. This forms coatings in tanks, settling pits, and ditches, and soon, unless removed by acid treatment, will effectively clog an injection well and reduce the flow of water back into the ground. The iron compounds in the water, most of which are dissolved from tanks and pipes, are in the ferrous form, and when exposed to the air are oxidized from soluble ferrous carbonate to insoluble ferric hydroxide, resulting in the precipitation of a gelatinous precipitate that will clog oil-field sands effectively: 2Fe(HCO3)2 + O + H2O -> 2Fe(OH)3 + 4CO2 The sulphates in strong sulphate-bearing water may be attacked by swarms of sulphate-reducing bacteria and more hydrogen sulphide may be produced. The hydrogen sulphide reacts with soluble minerals in the water to form black sludges. A knowledge of the chemistry of each reaction in oil-field water is important to the oil-field engineer, since means must be devised to prevent the formation of harmful precipitates that clog injection wells and to prevent corrosion of tanks by harmful products of biochemical processes. Methods of Treating Water before Injection into Ground* The open system of handling the waste salt water in the East Texas field consists of aerating and chemically treating the water to precipitate the unstable iron,

Jan 1, 1946

By E. C. Carris

THE loading of bituminous coal mechan¬ically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous pro¬duction in the United States was loaded by mechanical means. During the past i6 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all¬time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase in mechanical cleaning. The importance of mechanical cleaning of coal was recognized many years before the mechanical loader was introduced, because of the impossibility of cleaning manually the sizes below 2 in., and the increasing competition from other fuels. Utilization of mechanical loaders without mechanical cleaning on the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely intro¬duced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problems have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expendi¬tures; the solution taking the pattern of rearranging and improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. LARGE IMPURITIES The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1946

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By J. F. Myers, S. E. Sharp

THE safety data presented in this paper are based upon replies to a Questionnaire sent out to representative mining companies. The authors feel that it is a fair cross section of the milling industry, in that the 17 companies, of the United States and Canada, reporting on 22 mills, are scattered from the Hudson Bay to the Mexican border and from coast to coast. These data concern the accident records of the. various plants from 1939 to 1944, inclusive and the six years are divided into two periods. The first period (1939, 1940 and 1941) represents something of a normal operating condition. The second period (1942, 1943 and 1944) represents the period of time that was most affected by war con¬ditions. During the second period there was a high labor turnover, inexperienced workers were numerous, women replaced men in many kinds of work, a labor shortage existed more or less throughout the industry, and supervision was pushed for peak production. All of the companies reporting compiled their accident experiences for these six years in accordance with the standards set up by the American Standards Association (Engineering Societies Building, New York, N. Y.), consequently the tabulated data presented herein are comparable. The authors of this paper feel that the industry as a whole is greatly indebted to the personnel of the companies that furnished these data, which make this study possible for presentation. This survey covers a total exposure of 74,528,880 man-hours, with 105,471 man-days of lost time from 870 accidents. SAFETY RECORDS In Table I, the safety record is shown of the various mills reporting. The severity rate is usually conceded to be the most vital statistical figure in safety parlance, therefore the participating companies are listed in order of their severity rate for the combined six-year period, under size of organization. The table also shows the frequency rate as well as the frequency-severity ratio (F/S). As noted in Table 1, most of the companies suffered an increase in both severity and frequency rates during the second period; only six of the 22 enjoyed an improvement. From correspondence with the various plants, it seems that a few had very little labor shortage or turnover, and these were not greatly affected. A few plants, anticipating the situation, strengthened their training facilities and actually were able to show a better experience during the second period. This gives great credence to the value of organized training in any safety program. The frequency-severity ratio (F/S) shown in the last column of Table I offers

Jan 1, 1946

By John Mullen

Impingers TWO types of midget impinger apparatus are used at Climax. The Mine Safety Appliances Company's midget impinger (MSA) and the Climax Molybdenum Company's midget impinger (CMC) (Fig. I). The Leiman Brother's No. 25, positive displacement pump is used in the CMC impinger instead of the four-cylinder radial pump that is used in the MSA impinger. With the MSA apparatus it is possible to obtain the proper vacuum by adjusting the needle valve on the vacuum chamber, while with the CMC impinger the proper vacuum is obtained by varying the rate at which the pump is cranked. The Leiman Brother's No. 25 pump is built to displace 0.1 cu. ft. of air per min. when operated at 145 r.p.m. In the CMC impinger this pump is so geared that the required crank speed is approximately 59 r.p.m. Both types of impinger apparatus are equipped with a water gauge mounted on top of the case and they are calibrated and operated in reference to the gauge. The MSA impinger flasks and nozzles are used with both types. Calibrating Impingers A calibrated precision Sargent wet-test meter (Fig. 2) is used in calibrating the impinger apparatus. The apparatus is set up as for taking a sample in the field, except that the hose from the outlet side of the meter is attached to the impinger nozzle. One revolution of the large hand of the meter indicates 0.1 cu. ft. of air displaced. The impinger pump is cranked for one minute, therefore, at a rate that will cause the large hand of the meter to make one revolution. The gauge reading is noted, then the impinger is cranked at this rate for 10 min. and is checked for error. If the meter indicates that more or less than I cu. ft. of air has been displaced, the impinger must be cranked—ither slower or faster according to the error—for another 10 min. and again checked for error. This operation is repeated until the proper gauge reading for a sampling rate of 0.1 cu. ft. per min. has been determined. This gauge reading is used in all sampling operations until the impinger is again calibrated. An impinger is calibrated at least twice each week. MlCROPROJECTOR A Bausch and Lomb model B micro-projector is used (Fig. 3). It consists of a substantial metal base supporting the light source and a microscope. Illumination is provided by a Bausch and Lomb 4.5-amp. arc lamp with mechanical feed. A glass water cell filled with a heat-absorbing and color-filter solution is placed between the arc lamp and the microscope. Two types of solution have been found satisfactory— a 2 per cent solution of copper sulphate or a 2 per cent solution of picric acid and distilled water. This percentage may be varied to give the desired color to the light reflected upon the screen. Any standard microscope may be used. A Bausch and Lomb microscope with

Jan 1, 1946

By C. H. Frick

BEFORE presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. INTRODUCTION The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accu¬mulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3f 6-in. round-hole screen and over a 332-in. or a M 6-in. round-hole screen. USE OF SMALLER SIZES The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced-a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. TABLE I.-Screen Sizes Used for Small Sizes of Anthracite [ ] At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1946

By John W. Vanderwilt

THE unpredictable behavior of ground movement and subsidence has complicated the problems that attend the extraction of large quantities of ore. Special studies, particularly relating to coal mining, have yielded such a voluminous literature and so many involved controversial theories that a partial review would be difficult. Limited space makes any kind of a review impractical. The features to be considered cover only a relatively small part of the broad problems of ground movement and subsidence, but it is believed that this small part is critical. The practical aspects are important, since they bear directly on safety of mine workings, on recovery of ore and on dilution of ore in block caving and related systems for extracting large quantities of rock. The ground movement to be described occurs outside the vertical boundaries of a caved block in the area that is commonly referred to as being in the "zone of draw." "Draw" is a term that originated in the subsidence problems related to coal mining, and it is defined by a line drawn from the margin of the area caved underground to the most distant fracture at surface on the same side of the caved area as shown in Fig. I.1 " A line thus drawn is called the cave line, and its angle with respect to the horizontal is the cave angle or angle of draw. It is understood that the line is taken normal to the limit of mining, and in a vertical plane. The prevailing theories as to draw and angle of draw assume that appreciable movement occurred along the cave line, which has been described as a fracture resulting from the shearing action brought about by the weight of the overlying load. Fig. 2 shows diagrammatically the mechanics of ground movement adjacent to an area of subsidence according to the prevailing theory of draw (A, from Royce2) and, for comparison, ground movement observed in the Climax mine (B). The text in Peele's Handbook2 referring to Fig. 2 does not state the meaning of the "original position of top of workable ore" in the rectangular space above "ore in place," and the arrows are not explained. However, this presentation is most concerned with the zones outside the rectangle. According to the prevailing theory, as shown at the extreme left under A, Fig. 2, the vertical tension cracks at surface change at a shallow depth to shear fractures forming the cave line, and it is assumed that appreciable movement takes place along the cave line toward and into the subsiding caved block. The mechanics of ground movement observed in the Climax mine, as shown under B, Fig. 2, does not accord with the prevailing theory, particularly as regards the cave angle and draw. The vertical

Jan 1, 1946

By F. C. von der Weid

THE mining district of São Fidelis, in the northern part of the State of Rio de Janeiro, is situated on the Paraiba River, where it crosses the Serra do Mar (Mountain of the Sea), in the center of a mountainous country having numerous graphitic outcrops. For a long time, these outcrops were irregularly explored by local people, who had little means and no technical advice. A few years ago, the Cia. Brasileira de Mineração de Grafite took over the control of some of the more important outcrops and entrusted to me the task of studying the ores and establishing a flowsheet for a pilot plant to be situated in Sao Fidelis-the ore to be concentrated being mostly of a very high grade. MINERALIZATION AND ORES The rocks of the district are mostly gneiss and crystalline schists, with occasional interstratification of dolomitic limestone belonging to the Archean Brazilian Fundamental Complex. The general direction of the beds is roughly between 60° and 80°E., with variable dip, generally nearly vertical. Mostly, direction and dip of the graphitic outcrops is concordant with the embanking gneisses or schists. These outcrops seem to be aligned in two or three parallel zones (Pádua, São Fidelis, Macabú), the São Fidelis zone being the best known and the most important to date. Two outcrops of the São Fidelis zone, Saudade and São Benedito, are now being exploited. Mining has been carried out, so far, on a small scale. The mineralization consists of a vein of nearly massive graphite in a very compact, partially granitized gneiss, with vertical dip. The vein is most irregular, with nests and lenses irregularly distributed along the fracture plane. The ore consists chiefly (particularly in São Benedito) of massive graphite appearing and disappearing along the main direction of the vein, forming a succession of irregular lenses in a sort of rosary design. The average width is more or less one foot, with variations from zero to 6 feet. The lode minerals are quartz, a little feldspar and garnet (the latter having its origin perhaps in the embedding gneisses), with rare ferruginous clays on the outcrops. In Saudade a little pyrite, pyrrhotite and chalcopyrite is found occasionally, as well as a carbonaceous mineral, very light, black and shiny, with conchoidal fracture, looking like a sort of jet. The composition of this mineral has not yet been established, but it seems to be very complex. The mineralization seems to be hydrothermal at a rather low temperature, perhaps mesothermal. The paragenesis, according to samples from Saudade, seems to be as follows, the earlier minerals being listed first: pyrrhotite, pyrite, chalcopyrite, with quartz concomitant to the three and

Jan 1, 1946

By J. B. Macelwane

Geophysics differs from geology and physics in in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, vol-canology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratow system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist—the exploration geophysicist —calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist—the paleontologist— needs some knowledge of geology. Development of a Geophysicist Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydro1 ogist, or an exploration geophysicistp we may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1946

By L. D. Jaffe, John H. Hollomon

THE hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions .often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not, apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. HARDENABILITY If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and proeutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum4,5 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1946

By Fred C. Bond

A study of the settling and thickening of finely divided pulps was undertaken with the object of obtaining certain fundamental relationships, with resulting improvements in the design and operation of mechanical equipment. The subject has been treated in two parts: testing and batch thickening, and continuous thickening, including calculations of capacity and dimensions. Part 1. ? Testing and Batch Thickening The usual method of making thickening tests is to agitate the pulp with a plunger in a graduated glass cylinder and let it settle, while recording the time rate of settling. The settling rates corresponding to different pulp dilutions are found, the ultimate dilution obtained is measured, and the necessary thickener area in square feet per ton of dry solids per 24 hours is calculated, for each pulp dilution. The largest area found is used in selecting the proper thickener size.

Jan 1, 1946