Search Documents

By D. J. Coolidge, H. L. Sheakley

This paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is cornrnonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. I). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. Properties of the St. Peter Sand From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1948

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

INTRODUCTION IN a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-16 By "technical cohesion limit" is meant the technically determinable resistance to fracture. The four important factors are the stress system, plastic deformation, temperature, and the strain rate. The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously-mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal. In a recent paper of the series,15 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress.[$] Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence of plastic deformation at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air. As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not only by the work-strengthening, but also by strain aging. The present paper presents results of further investigation of the influence of strain aging on the fracture stress. There are two kinds of aging of steel.

Jan 1, 1948

By Bernard Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to be porous. In- [ ] deed, sponge iron, prepared by reduction of the oxide in a reducing gas, is generally accepted as quite porous, with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig I shows commercial tungsten powder magnified at 10,000X by the electron microscope,1 both etched and unetched. In an earlier paper by one of the authors,2 the existence of pores in tungsten powder [ ] was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these pores are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than 100 A, and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1948

By W. Rostoker

INTRODUCTION THE process of diffusion alloying of mixed powders offers attractive possibilities both commercially and experimentally. It avoids the fabrication difficulties arising from high alloy contents. Indeed, the process is facilitated by larger alloy additions. The direct formation of the part or test piece and the opportunity to perform machining operations under more favorable conditions are of no small importance. However, it is necessary to make only brief mention of the interesting features. As yet there have been few attempts to study this process in detail and to carry it to completion, if such is possible. It was intended not only to measure the intermediate and optimum magnetic properties of sintered alloys but to use magnetic testing itself as a means of following the progress of alloying under various conditions. Having established that alloys could be successfully synthesized by this technique, the opportunity was taken to study the magnetic properties of several alloys of iron and silicon which had hitherto been too difficult to prepare in suitable test piece form, While avoiding some of the difficulties inherent in the fabrication of alloys by orthodox methods, the diffusion alloying process introduces a few of its own. The first of these is the evaluation of the approach to homogenization. In recent years some notable contributions have been made to this question, but considerable uncertainty remains in its definition and evaluation. This work has concerned itself with further study of this problem and it is hoped that more light has been shed on it, The second of these difficulties arises from the presence of porosity. It is inevitable that in the consolidation of a loose bulk of powder, there should remain some voids unless extremely high pressures are repeatedly applied. It was therefore of importance to investigate their effect on magnetic properties. Recently this effect has been studied and certain predictions made of its behavior. It is believed that the experimental results presented here provide a sound substantiation of the theoretical treatment. The attempt has been made to synthesize five alloys of the iron-silicon system and three each of the iron-nickel and iron-cobalt systems. A series of experiments was also conducted on some of these alloys to test their susceptibility to heat treatment. Some unfortunate experiences have provided opportunity to report data on the deleterious effects of nitrogen on magnetic properties when present as a contaminant in protective atmospheres. MATERIALS, PREPARATION OF SAMPLES AND TESTING The purest materials available were employed for this work. A specially purified,

Jan 1, 1948

By W. C. Ellis, E. S. Greiner

METALLIC titanium has been prepared in small quantities since the beginning of the century. Hunter1 reported in 1910 that he obtained a malleable product of 99.9 pct purity by the reduction of the tetrachloride by sodium in a closed container. Later Van Arkel2 and Fast3 prepared small quantities of malleable titanium by thermal decomposition of titanium iodide. Another method for producing malleable titanium from tetrachloride was reported by Kroll4 who used magnesium as the reducing agent. More recently Dean, Long, Wartman, and Anderson5 working at the U.S. Bureau of Mines have reported the preparation of the metal on a pilot plant scale by the reduction of titanium tetrachloride by magnesium in an atmosphere of helium. Their product, which is malleable, was used in the present investigation. Early in 1948 after the work of this paper: was completed Campbell, Jaffee, Blocher, Gurland, and Gonser6 described the strength and working characteristics of pure titanium which was prepared by the iodide method on a scale producing 300 to 600 g per run, in the form of 0.3- to 0.4-in. diam rods. Their product is characterized by low hardness and large capacity for cold work which they attribute to a high degree of purity with respect to oxygen, nitrogen, and carbon. Titanium has a melting point of about 1725°C5 it may be classed as a light metal since the specific gravity is 4.5 g per cc-1. The crystal structure is close-packed hexagonal from room temperature t0 885°C. Above this temperature the structure is reported7 as body-centered cubic. The change in crystal structure has been associated with discontinuities in specific heat8 electric resistance9 and thermoelectric force10 at temperatures near 890°C. It is reported11 that annealed titanium has a tensile strength 0f 78,700 psi which can be increased by cold-work to 123,000 psi. In the present investigation, the lattice constants at room temperature, the thermal expansivity between 30 and 800°C, as well as the electrical resistivity and thermoelectric force against platinum between - 200 and 1000°C have been determined. MATERIALS For the measurements, two series of specimens were prepared from titanium furnished by the U. S. Bureau of Mines. The first was lade from an annealed sintered compact, 0.38 in. thick. Sections of the compact were cold-swaged with intermediate anneals in vacuum to the sizes used. Sizes over 0.25-in. diam were annealed at 1000°C and smaller sizes at 800°C. Specimens originating from the sintered compact are designated in this paper as A. The second series of specimens was lade from a rod of titanium, 0.19 in. in dial, which was cold-swaged with the necessary intermediate anneals to the required sizes. This series of specimens is designated B. The impurities in the specimens of titanium, determined by chemical analysis, are given in Table I. Oxygen and nitrogen which were not determined by analysis, are probably present although in small quantities in view of the ductility of the material.

Jan 1, 1948

Jan 1, 1948

By H. W. Graham

AS these annual occasions in honor of Henry Marion Howe continue through the years: there is progressively less likelihood that the lecturer will have had personal knowledge of Dr. Howe. The present speaker is one of those who unfortunately had no opportunity to come under the inspiring presence of this great metallurgist. A review of Howe's work shows it to cover a comprehensive range of interests and to evidence an impressive richness of detail. Not only was Howe at home in the laboratory, but he was familiar with the processes of iron and steel making and had a real understanding of them. His writings include much that is descriptive of processes with a wealth of material that is becoming of increasing historical value. He recorded his studies of the theoretical aspects of processes and published at least two process classifications, one in 1890 that was lengthy and somewhat theoretical, and a second in 1906 that was more of a practical listing. Wide as Howe's field of interest was, it is significant of the circumstances of his time that he gave- little consideration to raw materials or to their effect on iron and steel making processes. In 1933, Waterhouse, Howe lecturer for that year, presented a descriptive summary of the major steel making processes, and in 1946 Joseph discussed the blast furnace process. Otherwise Howe lectures have not dealt with processes as major subjects. In today's lecture, with no effort to describe the mechanical arrangements of iron and steel making facilities, it is proposed to examine the essential technological elements of the processes, to explore the inter-relation of these elements, and particularly to seek recognition and understanding of those factors which determine why certain processes are or are not used. The discussion of this lecture will deal with the major well-known large tonnage processes, with only such attention to processes of minor tonnage and special character as may be warranted for explanation by contrast. Subject to the errors of generalization and the shortcomings of condensation involved in presentation limited to a single hour, it is proposed to examine broadly but intensively those operations which convert raw materials into steel. It is an innovation for a Howe lecturer to discuss the raw materials of the iron and steel industry, but the changing circumstances of passing years intensify the influence of raw materials on processes and require the metallurgist to be alert for the process adjustments that may become advisable or mandatory. For a half century the metallurgical processing of iron and steel has followed a surprisingly straight path, but this does not necessarily mean that there are no curves in the road ahead. Ages ago primitive man came to know iron in its metallic form, not only by the

Jan 1, 1948

Jan 1, 1948

By Norman L. Wimmler, H. G. Iverson, S. Ricker, P. E. Oscarson, S. H. Lorain

This paper has been prepared with the principal objective of recording the results of the Bureau of Mines exploration of five major clay deposits in the Western Region. It is based mainly on data contained in unpublished Bureau of Mines reports. Acknowledgment is made to the Federal Geological Survey for its cooperative work with the Bureau of Mines, to the various State geological and mining departments, and other State and local agencies. Clay Exploration by the Bureau of Mines Much has been written and published on clays and clay deposits relating to their refractory, ceramic, and other qualities but such literature is lacking in analyses of the available alumina content of the clays and provides little indication of their possibilities as a source of alumina. With this new objective in view, a great many of the known clay deposits were reexamined and new ones discovered. The Bureau of Mines made preliminary examination of numerous areas in the western United States. Five of those most favorably indicated were systematically drilled, and in each a large amount of high-alumina clay has been found. These five major projects are Molalla and Hobart Butte, in western Oregon; Cowlitz-Castle Rock, in southwestern Washington; Ione, in California; and the Olson-Troy area in Idaho (Fig. I). Preliminary scout drilling was done in the Stockton deposit at Coeur d'Alene, Idaho; the White ware deposit near Lewis-town, Mont.; and 13 areas in the Spokane or eastern Washington region, where the most favorably indicated area, known as the Excelsior, is now being drilled more systematically. Preliminary drilling was undertaken in numerous areas adjacent to the major deposits and others more remote. As a result, large additional clay possibilities were found. The Clay Deposits The clay deposits under consideration are of the sedimentary or transported types, parts of which have been altered further by the agencies of weathering, ground water, or hydrothermal action. There are extensive deposits of residual clays in northern Idaho and in eastern Washington, but they have been found to be low in the available alumina and to contain much free quartz, mica, and unaltered feldspar. To be of value, they must first be subjected to beneficiation to remove these gangue minerals. The sedimentary clays have been derived largely from the decomposition, erosion, and transportation of granites, gneisses, schists, and basalts. At Molalla, some

Jan 1, 1948

By J. D. Lubahn, R. P. Carreker, J. G. Leschen

THE formation of slip bands in crystalline solids undergoing plastic deformation has recently been treated as a problem of nucleation and growth.1 A simplified theory was developed and shown to be qualitatively consistent with certain experimental observations reported in the literature, such as the frequent failure of slip bands to traverse the entire crystal, the effect of specimen diameter and temperature on the yield stress, and the occurrence of incubation periods in the deformation of suddenly loaded crystals. The theory further predicts the appearance of transients in the rate of strain of a crystal when the applied stress is suddenly changed from one constant value to another. A transient consists of a discontinuous change in the strain rate followed by a gradual approach to a steady-state value. Such transient behavior apparently has not been recognized in previous experimental work. The preliminary experiments reported in the present paper were undertaken to confirm the existence of the predicted transients and thus to determine whether a more detailed treatment of the nucleation theory of slip might be theoretically and experimentally fruitful. EXPERIMENTAL PROCEDURE A simple creep apparatus was assembled as shown in Fig 1. Very little insulation was used on the furnace in order to facilitate rapid changes of temperature. Temperature was measured with a thermometer placed in the center of the furnace and was [ ] controlled by adjusting the Variac setting. The specimens were cold-headed in split-cylinder grips. The strain was measured as total elongation by a dial gauge sensitive to 1/10,000-in. movement of the weight pan. Since the specimen gauge lengths were

Jan 1, 1948

By G. Sachs, L. J. Ebert, W. F. Brown

INTRODUCTION ISOTHERMAL transformation, or "austempering," of a carbon-containing austenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.1 Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4-5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.6-7 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels.8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140). The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1948

By Frederick L. Knouse

The south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19º to 21º and 30º south latitude; and from 40º to 41º and 30º west longitude. This includes the central part of Espirito santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Mar-tines, Espirito Santo (Fig. I). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through vitoria; and by the E. F. Minas-Vitoria and E. F. Centra] do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter- mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatite~, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. Early Operations Mining of quartz crystal in this region began in 1928 and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crysta1 as small as 10 grams. Since '94' only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of 100 grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, 01 Domingos Martines, Espirito Santo. Marketable quartz crysta1 was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large 'ores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. Production The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1948

By L. G. Sprague

The fact that this latest and most modern of the Universal Atlas Cement Company's plants at Northampton, Pa., is the fifth to be built on these same properties, and their development has been coincidental with the development of the portland cement industry in the United States, makes it appropriate to sketch briefly the history of the successive steps. In 1889 the original Atlas Portland Cement Co. started its first plant at Coplay, Pa., which is just across the Lehigh River from the present operation. Here the first successful rotary kiln was operated. These kilns were 6 ft. in diameter and 60 ft. long; they used oil for fuel until 1895, when the company developed the first burner for pulverized coal. Shortly thereafter the Atlas company acquired property on the Northampton side of the river and built its plants Nos. 2, 3 and 4 within the following 10 years. During the same period the production of portland cement in the country was increasing rapidly; owing largely to the development of the rotary kiln and improved grinding machinery, which lowered the cost and improved the quality of cement. The general tendency has been to increase the length of the kiln and grind both raw material and finished product Liner. In 1930 the Atlas Portland Cement Co. and the Universal Portland Cement Co. united to form the Universal Atlas Cement Co., and the same policy of improving the product has been continued. Because of the large amount of research carried on by manufacturers and consumers, including government agencies, there is a demand for cement of different chemical and physical characteristics for different kinds of structures. Hence many engineers in recent years have been asking for cements of certain definite chemical analyses, which they think are best for their particular jobs. This has compelled the manufacturer to make several different types of cement by variations of chemical composition. These are generally made by adding silica, iron and lime to the standard mixture, which necessarily increases the cost of the product. Therefore the Universal Atlas Cement Co., in planning the modernization of its Northampton plant, gave this particular phase of the problem considerable study. Research and experimentation have developed the practicability of making a wide variety of differently proportioned raw materials for cement by a process of subtraction rather than by addition. With such process, it is possible to discard the undesirable aluminates and silicates from the ample supply of impure limestone available from the company's property rather than by adding high-grade limestone obtained from distant sources. This procedure requires mineral separation by centrifugal sedimentation and froth flotation. Since the chemical and mineral constituents of Lehigh Valley "cement rock," together with the methods of separating them, have been thoroughly described in published

Jan 1, 1948

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By E. O. Binyon

The Blue Metal corundum-andalusite deposit, in the Buckskin Mining district, Douglas County, Nev., was explored by the Bureau of Mines in 1945. The results of that work were presented in Report of Investigations 3895, exploration of the Blue Metal Corundum Property, Douglas County, Nev. published in August 1946. That report also describes the property in detail, giving location, ownership, history, geology, and data on beneficiation tests. Further exploration was carried on in April and Way 1947, the results of which are presented in this report. The work consisted of 175 feet of drift and crosscut, bringing the total to 398 feet of underground working, as shown in figures 1 and 2. The 23-foot drift, which was the last work of the initial project, was extended 99 feet northward along the shear zone, and three crosscuts, spaced at approximately equal intervals along the drift, were driven to country rock on the hanging and foot walls of the zone.

Jan 1, 1948

By B. M. Larsen, T. E. Brower

INTRODUCTION AND SUMMARY BY "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath, To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over 1 million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct, The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 lb oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 lb oxygen replacing 145 lb ore per ton of steel) decreased the

Jan 1, 1948

By V. F. Parry

"INTRODUCTION During the war period the Bureau of Mines expanded its investigations on western coals principally in connection with Investigations of raw material resources for western steel production. Owing to the expansion of the steel industry, there was some concern regarding the availability of suitable coking coals; end because of the potential steel shortage, the production of sponge iron, using the lower-rank fuels, was considered. Work was conducted by the Bureau of Mines on exploration projects and on testing of coals both at the Central Experiment. Station at Pittsburgh, Pa., and at the Bureau of Mines Station at Golden, Cole.The results of these investigations are being published by the Bureau in several reports of investigations and technical papers. In making this resume of coal investigations, the work done by the Bureau of Mines at Pittsburgh in the Mining and Coal Carbonization Sections will be discussed and the investigations at Golden described in greater detail.INVESTIGATIONS OF WESTERN COALSThe Mining and Coal Carbonization Sections of the Coal Division, Bureau of Mines, under the supervision of A. L. Teeny es and J. D. Davis, respec¬tively, conducted many field investigations to locate and evaluate new sources of coking coals. Drilling explorations were made in Colorado, Wyoming, Utah, New Mexico, and Washington and revealed two important new reserves of coking coal. The first one studied was the Willow Creek bed at Kemmerer, Wyo., which was reported in 1945.3/ A recoverable reserve estimated at 11,200,000 tons was blocked out, and samples of coal were extracted for coking tests. The coking properties of the coal were not quite equal to those of Sunnyside coal, but it was indicated that a 50-percent blend of the Willow Creek with Lower Sunnyside will produce a satisfactory metallurgical coke based on Columbia steel standards."

Jan 1, 1948

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, 'iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other *producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since her particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely he kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1948

By R. D. Lee

A simplification of the method of Hurst and McCarty for conducting potentiometric model studies by the single probe method is presented along with experimentally determined invasion patterns for certain idealized flow problems. The analytical solution for one class of these problems is given. Finally, a general description is given of a newly developed instrument which permits direct mapping of flow lines and determination of transit times in potentiometric-model studies. Introduction The object of this paper is to present: I. A simplification of the method of Hurst and McCarty for conducting poten-tiometric-model studies of oil and gas reservoirs by the single probe method. 2. Results of a series of studies of certain idealized flow problems and the general conclusions to be drawn therefrom. 3. A description of a new instrument, the Chronocartograph, which greatly reduces the labor and time required for conducting potentiometric-model studies. Certain general conclusions may be drawn as results of the investigation of the idealized flow problems. They are: I. Injection and extraction areas should be separated by as great a distance as conditions permit since, in general, the recovery prior to first breakthrough tends to vary as the square of this distance. 2. Little advantage is to be gained by use of more than eight injection wells or groups of injection wells for the case of circular productive limits. 3. Elongated shapes of productive limits are best exploited by injection on the extended major axis only, with a line of extraction wells lying on the major axis. 4. The use of peripheral injection wells for elongated shapes is permissible, if necessary, but requires extension of the line of extraction wells. The exploitation of an oil or gas field is effected either by the expansion of the gas and oil, or by their displacement by another fluid. Both methods may be used simultaneously. When the displacement of the oil or gas is the controlling factor there arises the problem of mapping the progress of the boundary between the fluid in place and the displacing fluid. This problem is of particular interest in the operation of a cycling project in a gas-condensate field, where the wet gas is produced from one or more wells, commonly called "extraction wells.'' This wet gas is taken into a processing plant where the condensate is removed. The remaining "dry" gas is injected back into the field through one or more wells, called "injection wells," both to conserve the gas for future use and also to maintain the pressure in the field. In an operation of this type it is essential to anticipate the manner in which the dry gas will spread through the field, because the ultimate recovery of the wet gas depends

Jan 1, 1948