Search Documents

By Sage B. H., G. W. Billman, Lacey W. N.

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

By L. F. Marek, G. W. King, A. Bogrow

The purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction of FeO to Fe. Unless the gas has a CO!CO, ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles .at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available): the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity of the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"—i.e., the efficiency of conversion of the "available" CO supplied— is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1948

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By Leon W. Dupuy

A brief elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kid or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico1-' during the 1920's. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will Serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. Selection of Method of Drilling Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. Factors Governing Selection of Diamond Drilling The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1948

By Vaughn Moyer

A method for incorporating well drawdown effect into reservoir calculations is presented in detail, together with examples of its use for widely divergent conditions that could be normally encountered in oil reservoir sands. Tentative conclusions as to the effect such factors as permeability, producing interval, well spacing, or well damage caused by completion or repair practice could have upon economic ultimate recovery are reached. It is carefully pointed out that the conclusions reached are subject to limitations indicated in the text, and placed upon all calculations made in the paper. Introduction Papers have been presentedl-3 in which theoretical depletion histories for reservoirs under equilibrium conditions and no appreciable well-bore drawdown pressure are determined. However, except for a limited number of cases, appreciable drawdown Pressures in a well bore exist, and Pressure and saturation gradients consequently vary throughout a reservoir. This Paper is an attempt to incorporate well-pressure drawdown into reservoir history, and to analyze certain factors, such as those involving recovery, well spacing, and productivity index, from the standpoint of permeability and drainage radius. BY incorporation of drawdown into reservoir history, it is believed that theoretical considerations will more closely approxi- mate actual reservoir behavior experienced in an oil field. For purposes of simplification, a solution gas-drive type field1 without primary gas cap, has been selected. Basic Data and Assumptions Details of equilibrium saturation conditions for no drawdown production for various pressures in a reservoir are deter-minable by methods described by several are permitting the construction of a curve of oil saturation vs Pressure for any selected combination of initial interstitial water and hydrocarbon saturation (Fig I). This curve is then a description of equilibrium saturation conditions at any given pressure in a reservoir. Developing the above, details of saturation and flow permeability may thus be determined for any increment or portion of a well drainage area or reservoir. In this manner the effect of pressure differential (drawdown) may be incorporated into reservoir and well drainage considerations. It is pointed out that this method thus makes use of no-drawdown equilibrium production data, superimposing a draw-hwn effect upon them. It also assumes that net flow conditions in any considered increment of reservoir are not materially altered by the entrance of fluids from other increments into them, but approach equilibrium for the existing pressure and saturation (i.e., each increment behaves in more or less independent fashion, dependent largely upon the equilibrium considerations mentioned above)

Jan 1, 1948

By G. Sachs, S. I. Liu

INTRODUCTION IN a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in, Fig I,§ the ductility (EF) retained after prestraining in tension by a certain amount (EI) and measured in a subsequent tension test is represented by a straight line sloping down under 45°. If a compression of the same magnitude as the first tension is inserted (E2 - EI) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. . The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.2 As also shown in Fig I, the ductility in subsequent tensile tests decreased with compression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount E1, subsequently straining in compression by an amount E2, and finally determining the retained ductility, Ef, in a tensile test. Prestraining in tension is then represented by E1 > o and E2 = o. Prestraining in compression is given by E1 = o and e2 < o. Balanced cyclic straining is defined. by the condition E1 > o and E2 = -El. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, E1, and the compression strain, E2, within extreme limits; El varied between 0.06 and 0.28 and E2 between -0.008 and -0.60 approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date. The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the subsequent tensile tests.

Jan 1, 1948

By W. B. Mather

The object of this paper is to record and interpret data collected during the examination of over 250 barite deposits in the Central Mineral District of Missouri. In the course of this study, the origin of the deposits, which the author believes to be hydrothermal, has been given particular attention. Economic barite deposits occur in two main areas in Missouri: (I) in the Washington County District of Southeast Missouri, from which over 90 pct of the state&apos;s production is derived; and (2) in the Central Mineral District, which includes portions of 15 counties in Central Missouri (Fig I). Barite in the smaller Washington County District is mined from widespread low grade, relatively shallow residual deposits, whereas in the Central District, it is mined

Jan 1, 1948

By P. de Vitry, Willis P. Mould

The wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually pis or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired anale. The usual drive is by a 10-hp. motor through a gear reducer, on which are Insti- two grooved sheaves, One of which is keyed and the other free running On the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1948

By M. R. Geer, H. F. Yancey

WITH the exception of pneumatic processes and ii few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral- dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficiation process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and else- where, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment for many years, and more recently driers employing centrifugal force have gained in popularity. 1 A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal-a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. OBJECT AND SCOPE OF INVESTIGATION Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it on coal slurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1948

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook&apos; has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries&apos; method for grain-size measurements consists of counting the number

Jan 1, 1948

By Thomas E. Leontis

INTRODUCTION THE importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication,1 attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne.2 The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Zn† alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-1Zn,†Mg-3Zn, Mg-4.4Zn, Mg-6Zn, and Mg-10Zn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. LITERATURE The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison.3 Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,4 Dumas and Rockaert,5 Haughton and Prytherch,6 and by Spitaler, the last being reported by Beck.7 A slight superiority in the tensile strength of chillcast Mg + 8 Zn alloy over the sand-cast alloy was noted by Maybrey 8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1948

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard&apos;s rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By Axel Hultgren

IN ingots of silicon-killed carbon steel made without addition of - aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially. In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents arid, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,10,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis17 and their amount to increase from the top downward in the axial region .2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form," by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.15 Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19,20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping&apos; or of refractory material from various sources1,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistance to hydrofluoric acid, imparted by the alumina content. Silicate inclusions, are often referred to as. the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1948

By J. R. Lewis

During the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remainig constant, the time for reduction of a given sample of ore is inversely propor-tiofid to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i,e., where carbon reacts directly with the ore. Some recent work by philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the rA, ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author&apos;s intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to Say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner&apos;s theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed4 he concludes that: "In genera&apos;, the carbon in blastfurnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. hlartin,3 in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the Proper sizing of the Ore particles&apos; Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1948

By H. P. Croft

[ ] Professor Hibbard&apos;s paper presents a very interesting theory concerning the influence of texture on the tendency of brass tube to stress-corrosion crack. I should like to present the result of some work done in 1941 which may throw further light on the subject. In the first place, in regard to his review of the influences of grain boundaries, we not only confirmed the findings which he quoted, but also were unable to crack single crystals of beta brass in the standard mercurous nitrate test in 50 hr under loads up to 18,500 psi. Samples containing two or more crystals of beta brass always cracked at grain boundaries and generally followed the same pattern as for alpha brass, although cracking occurred sooner than in alpha brass under the same conditions. Such a specimen is shown in Fig 4. Second, at the possible risk of repetition, we should like to call attention to the reported role of grain size as influencing the tendency to stress-corrosion crack. This phenomenon, originally mentioned by Dr. Allan Morris in the Transactions, AIME, 1931, is illustrated in Fig 5, showing the effect of variations in grain size on the tendency of drawn brass wires to crack under load in the mercurous nitrate solution. This was taken from my work published in Proceedings A.S.T.M. 41, (1941), 905.

Jan 1, 1948

By John L. Lamont, Walter Crafts

SECONDARY hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to the secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at 1100°F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader.3 Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to 1100°F, but the mechanism of the process has received little consideration .

Jan 1, 1948

By M. Howard Berliner

During the spring of 1944, the Bureau of Mines investigated the Crescent mine area near the village of Rewey, Iowa County, Wis., as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the Nation&apos;s war program. The Bureau of Mines completed 24 churn-drill holes in an area immediately to the west of a mineralized section which had been mined through shallow workings for lead and zinc more than 40 years earlier.

Jan 1, 1948

By A. Ignatieff

This is the first in a series of Coal Technology Reviews being prepared in accordance with a recommendation voted by the Coal Division in session at the Jubilee Meeting, Vancouver, April, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review&apos; of Coal Technology, for distribution among those concerned in the production and use of coal in Canada. This recommendation was subsequently endorsed both by the Council of the Institute and by the Dominion Coal Board. Further reviews (or digests) will appear at intervals in the Bulletin, or will be published and distributed by the Board which, meanwhile, has undertaken to distribute reprints of Mr. Ignatieff&apos;s review.-En. * * * The fields in coal mining technology which are considered to demand most attention and study at the present time are reviewed under the headings appearing below. Mechanization In the light of the growing shortage of skilled miners and the necessity of mitigating constantly increasing mining costs, interest continues to centre in mining methods and applications of mechanization chat will produce the maximum reduction of man power. The growth of strip or open-cut mining, also, is a consequence of this trend. Mechanization at the face attracts most attention and the trend is toward developing and adopting machines capable of cutting and loading the coal in one operation instead of having the separate operations of cutting, drilling, blasting, and loading. In Great Britain, where longwall mining is? the general practice, the A.B. Meco-Moore machine still receives much attention, and accounts describing its performance over reasonably long periods have appeared in the technical press.

Jan 1, 1948

By Reynold Q. Shotts

INTRODUCTION THE small domestic underfeed stoker as now designed is unusually sensitive to the coking and plastic properties of coals, and when the attempt is made to burn the high rank coking and caking coals of the Appalachian fields, serious trouble may occur. Part of the trouble may be caused by the ash content and clinkering characteristics of the particular coal in use, but more often it is the result of an excessive accumulation of coke in the form of "trees" or masses in the fuel bed. Often the zone of burning becomes so restricted that the fire goes out, and in extreme cases the fire may be lifted completely out of the fuel bed and away from the air ports. Even if the fire is preserved, excessive coking may cause response to subsequent heat demand to be slow and irregular. Coke trees seem to grow. most readily during periods of hold-fire operation, so that in order to preserve the fire in mild weather it is often necessary to set the timer for such a long operating period each hour that much unneeded and unwanted heat is developed, causing discomfort. During demand periods the fire may pick up so slowly that the intense burning which develops just before stoker cut-off causes a serious overshooting of the thermostat. Stoker coal performance tests which have been made in a number of laboratories 1, 2, 3, 4, 5 are one method of approach to the problem of selecting stoker coals. As yet these tests have not been standardized and they are expensive and time-consuming. The value of the results probably increases with the length of the test. Sherman and co-workers at Battelle Memorial Institute believe that even a one-week test is not too reliable a trial2 and it is quite likely that others will agree. A great advantage of such tests is that characteristics of coals, other than the tendency to form coke masses, may be evaluated from them. The selection of stoker coals would be greatly facilitated if there existed some simple measure of the tendency of a coal to form coke in a fuel bed. Although possessing all of the disadvantages of any small-scale laboratory test, the test for the free-swelling index of coal has been found useful for evaluating the probable effects of swelling properties upon combustion. 7 Ostborg, Limbacher and Sherman, have shown that the test can predict, roughly, the tendency of coke to accumulate in the fuel bed of a domestic stoker. They also gave instances of its value in predicting combustion behavior in some large installations. The use of the test for free-swelling index has become well established and has been adopted as a standard by the American Society for Testing Materials.8 When domestic stoker coal investigations began at the State Mine Experiment Station in the summer of 1944, it was decided

Jan 1, 1948