Search Documents

By Jack White, Ralph B. Adair

The Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1934, 1935, 1936, 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. Ore Treated The ore consists of fine grained highly siliceous, felspathic and argillaceous quartz- ites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about I oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or,, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct- Crushing Operations The first stage of crushing is done under. ground where the oversize from I2-in. grizzlies is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35O slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a.rate of over 500 tons per

Jan 1, 1949

By H. E. Heide

The serious shortage of domestically produced asbestos during the war prompted the Bureau of Mines to investigate reported asbestos deposits in Alaska. The most promising' appeared to be these in the Cosmos Hills and Jade Hills areas along the Kobuk River in northwestern Alaska. The deposits along the west side of Shungnak River, a tributary of the Kobuk River, were the first to be investigated by the Bureau, in the summer of 1944. Four bulldozer trenches were excavated, from Which a 2-ton sample was taken. This sample was shipped to Rolla, Mo., for testing in the Bureau of Mines laboratory. In the summer of 1945 an investigation of asbestos deposits on Cosmos Creek, also a tributary of the Kobuk River, was begun; the work was completed during the field season of 1946.

Jan 1, 1949

By George B. Clark

The "Munroe effect" of shaped explosive charges was discovered by Charles E. Munroe more than 50 years ago (in 1888), but it was not until World War II that it was put to any practical use. Both Allied and Axis armies used the principle effectively in bazooka projectiles, artillery projectiles and in fixed shaped charges. The first two were used primarily to combat tanks and other armor and the latter to assault pillboxes and other fixed concrete emplacements. Many engineers and others who saw the military application of the jet effect of shaped charges believed application would be possible in many industrial fields where blasting is used, such as mining and quarrying. Some work has already been done on the problem of making shaped charges applicable to mining operations. Experimentation conducted at the National Tunnel and Mines1 was directed primarily along the lines of use of shaped charges for secondary blasting in connection with long-hole stoping methods. Experimentation initiated earlier and conducted by the author2 at the University of Utah on a more scientific basis was directed at revealing the basic principles of the functioning of shaped charges, as well as the feasibility of using them in mining operations after the principles of their operation had been clearly defined. It was found that: (I) a given design of charge required an optimum standoff to make it most effective, either in penetrating solid rock or steel (see Fig 3); (2) for a given design of charge there exists an optimum ratio of charge diameter to charge height above which the increase in effectiveness of the charge decreases rapidly (see Figs 4 and 5); (3) partial confinenlent has the effect of making charge performance much more consistent; (4) the higher power and higher velocity explosives tested are much more effective than relatively low-strength explosives; and (5) shaped charges may be adaptable to mining operations in secondary breakage and drilling blasting holes. Fig I is a diagrammatic sketch of the action of a shaped charge for two types of cavities, while Fig 2 shows the approximate manner in which the jets are believed to be formed when an explosive wave encounters the cavity, approaching it from the top. The experimentation already completed has laid the foundation for further research in the study of shaped charges. Standoff effects, effect of the strength of explosives and other features have been fairly well established. Such elements in the design of shaped charges as (I) geometry of cavity liners, (2) relative horizontal dimensions of explosive column, (3) effect of various metals and alloys in cavity liners, (4) percentage studies of jet energies, and

Jan 1, 1949

By Nathan C. Rockwood

LIME is a very general term applied to products of limestone, in popular treatises often incorrectly, including ground or pulverized limestone used in agriculture. When used without qualifying adjective, the term usually means burned or calcined limestone, or quicklime, or calcia. The corresponding calcined product of magnesite is magnesia. If the calcined rock is relatively pure calcium carbonate, the resulting lime is a "high-calcium" lime; if the rock is dolomite, or a combination of calcium and magnesium carbonates, the lime is a "dolomitic" or a "high- magnesium" lime. There are various grades in between, depending on the percentage of magnesium carbonate and other ingredients in the raw rock. For some industrial purposes only high-calcium limes are suitable; in other processing-as, for example, neutralizing acid wastes -the relative percentages of magnesium and calcium carbonates in the raw material are not important. Limestone is burned (roasted or calcined) in furnaces known as lime kilns by direct exposure to the hot gases and flames. When heated to incandescence, the carbon dioxide content of the rock is expelled, leaving calcium and magnesium oxides, according to the formula usually written: [ ] This thermal reaction is reversible, which requires that the lime be withdrawn from the "calcining zone" of the kiln about as fast as made. Pure calcium carbonate would lose 44 pct of its weight in the calcining process; dolomite, 48 pct. Generally, the lime will retain the approximate size and shape of the piece of rock from which it is made but some few limestones tend to break down into granules or dust. Hence lime (quicklime) comes from the kilns in lumps or granules and normally is packed in water- tight containers in these forms, or is pulverized after calcination.

Jan 1, 1949

In, one stage of the purification sequence of the zinc sulphate electrolyte used at Risdon, cobalt is, precipitated as cobalt nitroso-,B-naphtholate, which is separated from the solution by filtration. Owing to the method of conducting the purification the filter cake contains much gypsum, unconsumed calcium hydroxide, basic zinc sulphate, and entrained zinc sulphate solution, Small amounts of iron and copper that have escaped previous purification steps are also precipitated with the cobalt as nitroso-,B-naphtholate. Thisprecipitate, normally carrying about 18% cobalt, is the raw material for the production of cobalt oxide, cobalt sulphate and cobalt metal.COBALT OXIDEThe main problem in the preparation of a reasonable grade of cobalt oxide from the filter cake is the economic separation ,of the cobalt nitroso-,B-naphtholate from the gypsum. This was solved by the application of flotation. It was discovered that the cobalt nitroso-,B-naphtholate, under correct conditions, would float without any addition agent, giving a relatively high grade concentrate. A plant, was built and has been in operation since 1936. The filter cake is pulped with water and pumped to one of two mechanically agitated tanks, eath capable of holding one day's output. Sulphuric acid is added until the free acid concentration reaches about 3 gm. per litre. Basic zinc sulphate is dissolved and calcium hydroxide converted to gypsum. The pulp, carrying about 2t lb. of solids per gallon, is pumped at a suitable rate to the first of a series of 10 flotation, boxes.. Each box is 3 ft. by 2 ft. 9 in. by 5 ft. deep, and, all have a common, pulp level, since the...

Jan 1, 1949

IT is a pleasure for the translators to record their gratitude to the Seeley W. Mudd Memorial Fund of the American Institute of Mining and Metallurgical Engineers for underwriting the cost of publication of this volume, to the Printing-Office of the Yale University Press for doing an unusually fine printing job, and to the following for granting permission to reproduce the title pages of volumes in their collection: The Bibliothèque Nationale of Paris, for edition A of the Bergbüchlein; the Osler Library of McGill University, Montreal, for editions B and G of the Bergbüchlein and edition D of the Probierbüchlein; Mr. Herbert Hoover, Jr., for editions C and E of the Bergbüchlein and editions E, M, N, and 0 of the Probierbüchlein; the Parsons Collection of the Reference Department of The New York Public Library, for edition D of the Bergbüchlein; the Library of the Bergakademie Freiberg, for edition F of the Bergbüchlein and editions A, H, and L of the Probierbüchlein; the Herzog August-Bibliothek of Wolfenbüttel, for edition C of the Probierbüchlein; the British Museum. Library, London, for edition I of the Probierbüchlein; and the library of the University of California at Berkeley, for edition J of the Probierbüchlein. The cooperation of those who helped with the translation of the Bergbüchlein is acknowledged on p. 64. A. G. S. C. S. S.

Jan 1, 1949

By W. W. Weigel

In "Mine Drainage, Southeast Missouri Lead District," Trans. AIME, (1943) 153, 74-81, the general water conditions in the lead mines of Southeast Missouri were described. Some comments developed from the experience of time and some further

Jan 1, 1949

Jan 1, 1949

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By H. G. Harper, R. C. Hart

"The Mississagi quartzite is the basal formation of the Quirke Lake trough. As it is traced around the rim, a gradual change in dip is observed, as follows:Northwest corner 50 degrees south.Algom Quirke mine 34 degrees south.Quirke Lake 25 degrees south.Whiskey Lake 22 degrees west.Pecors Lake 25 degrees north.Algom Nordic mine 18 degrees north.Elliot Lake 11 degrees north.Pistol Lake 5-7 degrees west.Thus the apparent synclinal axis is a curving east-west line lying closer to the north limb than to the south. The axis appears to plunge west at about 5 degrees.The Huronian sediments lie on a basement of granites, gabbros, and volcanics. Diamond drill evidence indicates that this basement has a surface of peneplanation, and that the areas of soft basic rock have a smoother topography than the granite. For the most part the orebodies at the Quirke and Nordic mines overlie a basement of soft basic rock.The Mississagi formation is the host rock of the deposits, and its primary structures are suggestive of the conditions under which the conglomerate beds were deposited. Cross-bedding is common, although normal bedding varies from thick to thin to essentially lacking. Grain gradation is not common. Where coarse and fine grains occur together, the coarse tend to be more rounded than the fine. These features are characteristic of shallow-water deposits, laid down above the lower limit of wave action. Therefore, the quartz-pebble conglomerates probably represent ancient water courses, bays, beaches, and bars.The causes governing the creation of the trough can only be conjectured, but there is evidence that both subsidence and compressive stresses played active roles. Drag-folds in argillite beds near Whiskey Lake indicate compressive stress. On the other hand, gentle crumpling in thin-bedded limestones on Quirke Lake is probably due to pre-induration slumping and folding. If strong compression had been widespread within the trough, one would expect drag-folding and shearing of the incompetent beds to be more general. Two large-scale, fold-like structures were mapped by Collins, but their axes do not parallel the trough axis, and they are therefore not related to the major structure."

Jan 1, 1949

By R. L., Fullman

During the past year there have been a number of significant investigations that have furnished evidence on the driving forces governing grain growth and on the role played by boundary impurities. Thus Burke has shown that in high purity alpha brass the rate of grain growth in the earliest stages is approximately inversely proportional to the existing grain size. This relation agrees with one derived by Zener assuming that surface energy was the driving force in grain growth. Also in confirmation of the surface energy hypothesis, Burke found that growth virtually stopped when the grain boundaries or even only the grain corners were melted.

Jan 1, 1949

By G. D. Jermain

Exploration of the Antimony Peak district by the Bureau of Mines was conducted under the authority of the Strategic Minerals Act of 1939. Antimony was one of the seven metals designated at that time as strategic by the Secretaries of War, Navy, and Interior upon advice of the Army and Navy Munitions Board. As a result of many field examinations, the Antimony Peak property was chosen as one of the most attractive for the possible development of emergency antimony reserves. Exploration by the Bureau of Mines began in November 1940 and was concluded in May 1941.

Jan 1, 1949

By William A. Beck

Bauxite was discovered in the Springvale district in 1916. About 16, 000 tons was mined in the period 1916 to 1922, but no bauxite mining has been done since that time. The Bureau of Mines explored for bauxite in the district from September 5 to November 18, 1943. During the life of the project, the Bureau of Mines obtained mineral exploration agreements covering a total of 11,330 acres from 50 property owners. A total of 388 holes were drilled on five of these properties and 164 samples were taken and analyzed. The Springvale bauxite district includes an area of about 30 square miles in the northwestern part of Randolph County, Ga. The village of Springvale is in the west central part of the district, and Cuthbert is 8 miles southeast of it (fig. 1).

Jan 1, 1949

Jan 1, 1949

By Charles H. Behre

SLATE (Thonschiefer, German; ardoise, French) is a rock, an aggregation of mineral grains, occurring in nature, which is used for roofing and other special purposes. It is finely granular and crystalline and generally derived from an originally clayey bed or series of beds. As a result of its having been put under essentially horizontal compression by geologic forces, this material now has its particles elongated and flattened so as to yield a very good rock cleavage along the flat surfaces of the minerals, a feature entirely independent of the original bedding in the rock. This is the gist of the definition adopted by the Committee on Slate of the American Society for Testing Materials. Slate differs in varying degrees from most other common rocks (such as limestone, sandstone, granite, and "trap") in chemical and mineral composition. Its most characteristic feature, however, is its tendency to fracture along a series of very nearly parallel and very closely spaced smooth planes, called cleavage planes. This property of cleaving, above all else, gives slate its industrial value. ORIGIN AND MODE OF OCCURRENCE Most of the features of slate might be anticipated from its origin. Being a rock rather than a mineral, its composition may vary consider- ably without impairment of value. In most slates, the material of which the rock is now composed was once deposited as clay on the bottom of a lake or sea. Subsequently these clayey strata were compressed by the kind of lateral pressure that folds rock strata, the minerals of the clay being changed or metamorphosed. In the chemical reaction involved, new and essentially plane-shaped minerals belonging to the mica groups were developed. Other minerals were formed but micas generally pre- dominated. These were oriented so that their two longer dimensions are approximately at right angles to the last effective direction of pressure. Since the crystals are thus subparallel, fractures can be developed easily along their surfaces, much as cards can be separated by inserting a knife blade between them. For the foregoing reasons, slate is found in noteworthy amounts

Jan 1, 1949

By H. L. Riley, B. W. Gandrud

A froth flotation unit was added to the DeBardeleben Coal Corporation's Empire washer at Empire, Alabama, in the fall Of I94O following an investigation of possible ways and means of recovering coal values from settling-tank overflow or slurry. Officials of the DeBardeleben corporation hoped that some practical and reasonably economical way could be found for recovering fine coal from overflow water, although there had as yet been very little progress along this line in the Alabama coal fields. The Bureau of Mines was asked to cooperate in the project through its Southern Experiment Station, at University, Alabama. This paper presents a brief description of the process and the installation that resulted from the investigation of the overflow water or slurry problem at the Empire mine. The experimental data include' as a Part of this Paper were obtained during the course of the investigation in 1940 Since that time, however, the flotation unit has been running more or less continuously without significant operational changes and is still Performing pretty much in accordance with the data obtained in 1940. Flowsheet at Empire and Type of Coal Treated The Empire mine is developed on the Black Creek bed near the the border of the Warrior field. The coal in this bed is extremely low-ash and although there is an almost complete absence of bone coal and partings, the bed is so thin that, with mechanized mining, a high percentage of rock from roof and floor inevitably gets into the run-of-mine coal. The thickness of the Black Creek bed throughout the part of the Warrior field in which it is mined extensively is rarely over 30 in. and probably would average about 25 in, the coal is of the high-volatile A rank and of excellent quality, but as a result of admixture of roof and floor material, the run-of-mine product usually contains I ; to 20 pct rock by weight. he following is a proximate analysis on an "as-received " basis of a typical seam sample from the Empire mine:' moisture, 3.0 pet; volatile, 34.6 fixed carbon 58.3; ash, 4.1 This sample shelved 15,070 Btu per pound and 0.9 pct sulphur on a moisture-and-ash-free basis. In the Empire preparation plant the lump sizes above 3 in. are removed and hand-picked on a Marcus conveying Screen, the 3 to ? -in. size is removed by vibrating screens and washed in two Montgomery single-cell jigs, and the ?-in. to o slack is cleaned on four diagonal

Jan 1, 1949

By O. M. Bishop

The Douglas fluorite property is in the Empire district of eastern Pope County, Ill., which lies near the west boundary of the productive Southern Illinois fluorspar field in Hardin and Pope Countios. Production from mines on the Douglas property accounts for about one-half of the 72,000 tons of fluorspar with which the Empire district is credited. This output was from the Sycamore, Pierce, Slapout, and Empire veins, which are normal fissure veins of little displacement along which there has been local wall-rock replacement by fluorite.

Jan 1, 1949

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiC1-KC1 mixtures, as first proposed by Gunkz.2 The details of the industrial process have not been made public hut Osborg8 stated that an efficiency of more than 90 pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on' German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of 140 kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, SiO2, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, Director, with respect to the iron and calcium Content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1949

By J. A. Markovits

Coal has been hydrogenated in Germany on a lather extensive scale for the past 20 years, but the process is new to the United States. Although pressures up to 15,000 pounds per square inch have been employed on commercial scale in the synthesis of anhydrous ammonia, and there is evidence that valves, tubing, and equipment have been developed recently up to 30,000 p.s.i. working pressure at moderately elevated temperatures for limited industrial production of plastics, such pressure ranges are unusual in American industry, and equipment designed for them is not commonly available. In the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., 10,000 p.s.i. operating pressures are combined with temperatures up to 1,000° F., and the materials to be processed under these conditions range from gases to mixtures of viscous liquids containing high percentages of abrasive solid particles. These service conditions presented unusual engineering problems requiring thorough investigation, Limited financial resources arid rigid time schedules inherent in the synthetic liquid fuels act often forced decisions before the best answer to a problem could be developed. Sometimes the ideal technical solution proved to be beyond the financial limitations of the demonstration-plant program.

Jan 1, 1949

By Myers, J. F.

The purpose of the mill tests reported herein, was to determine the relative power efficiency of fast and slow rod mill speeds on the ores of the Tennessee Copper Co. The tests were carried out at the lsabella Mill of the Tennessee Copper Co. under normal operating conditions. Every effort was made to keep the ore supply and other conditions constant, but it will be noted that some slight variation did occur. The open circuit 6 by 9 rod mill, and ore, used in these tests have been previously described.' Four motor drive pinions were available and the tests were performed in the following manner: each pinion was used to drive the mill for a period of one week. Constant sampling prevailed during the test run, and a composite sample for each speed test was made. Realizing that some slight liner wear took place during the four-week test-run, and that some slight variation of the ore may have taken place, a second and then a third series of four-week test- runs were made with the four different pinions. The screen analysis of each of the thee-week run samples at the various speeds were composited and the results are shown in Table 1. The authors feel that the 12 weeks of operation consumed during these test-runs would represent fairly the effect of each mill speed. The data of line 37 show that within the error of sampling and plant operation, the tons of minus 65-mesh material generated per horsepower hour was the same at all four speeds.

Jan 1, 1949