Search Documents

By W. L. Crentz, E. E. Donath, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By F. M. Lewis, J. F. Myers

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the 11-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the 11-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 11/2 in. and a further gain of work accomplished of 2.1 pct when we went from 11/2 in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By W. J. Tait, A. E. Craig, E. P. McCurdy

C. M. Marquard—The problem of the automatic control of a grinding-classification circuit is not nearly as simple as has been indicated and it cannot be universally solved through the application of this device. The sound emanating from a ball mill such as the metallic clink of the balls against the liners can at times be misleading. The fact that the sound level due to the balls hitting the liners may be at a minimum does not necessarily mean that the mill is properly loaded. I have in mind an ore we treat that has a soft talcy gangue. The soft fluffy nature of this material makes the sound from the ball mill a most misleading parameter that is worthless as a means for controlling the amount of ore fed to the mill. In every milling plant there are transportation lags due to the time it takes the ore to travel from the mill bins to the ball mill. In many plants there may be several different transportation lags due to varying distances of bins from ball mill. These transportation lags can most seriously affect the operation of a controller. It has been found that under many circumstances the transportation lags can be so bad as to cause the controller to hunt seriously. Hunting can and in many cases does become so serious as to render automatic control impossible because of the surges it causes. While it is possible to compensate for this type of lag, this apparatus does not lend itself readily to accomplish the required compensation. Further, if there are groups of bins at various distances from the ball mill, compensation for one may not be sufficient or may be too great for another. Each milling plant presents a separate problem. The apparatus as presently described does not appear sufficiently flexible to accomplish this. It should be noted that the load on the classifier rakes is determined by measuring the current input to the rake drive motor. Variations in line voltage will

Jan 1, 1951

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By A. L. Labbe, J. J. Donoso

Hard-won experience in the operation of smelting plants has pointed the way to the most efficient design and economical operation of a baghouse system for recovery of metallurgical fumes. This paper treats of the principles governing bag filtration and the factors most directly affecting bag life. Methods for temperature conditioning of smoke previous to filtering are described and the evolution of bag shaking mechanisms is brought up to date. THE history of the bag filter process, as applied to the recovery of metallurgical fumes, goes back to 1876, when the Lone Elms Works of Joplin, Missouri, erected a two-section baghouse for filtering fumes from Scotch Hearth lead smelting furnaces. By modern standards this installation was crude, but the basic operating principles remain essentially the same today. Great progress, however, has been made in the mechanization of the process by the use of devices for mechanically and automatically cleaning bags of adhering fumes, in the use of instruments for recording and controlling the variables affecting baghouse operation, and in the conditioning of the smoke previous to filtering. The principles governing bag filtration of fumes were investigated in 1929 by A. J. Seitz of American Smelting and Refining Co., and he arrived at the following conclusions: 1. Pressure on Bags at Constant Volume: The rate at which the pressure builds up in a bag with constant volume is directly proportional to the time, with the same kind of smoke and dust burden (fig. 1). 2. Pressure on Bags for Change in Volume: With equivalent smoke and dust burden, the bag pressure increases with the square of the increase in volume. The rapid increase in pressure is due to (1) increase in volume, (2) increase in amount of dust on the bag, and (3) more intense packing of the dust at higher velocity (fig. 2). 3. Effect of Intensive Filtering on Pressure: Since the pressure builds up directly as the square of the volume, with the same smoke and dust burden, it is necessary to shake the bags in that increased ratio, and vigorously, to keep the pores of the bag open and pressure down. This increases the wear on the bags and the dust losses. 4. Effect of Shaking on Dust Losses: The losses are in direct proportion to the frequency of shaking because the loss takes place immediately after shaking, before the bag seals itself. Tests show that with hand shaking the last 20 pct of the removable dust requires seven times more shaking per unit weight of dust than the first 80 pct. 5. Effect of Fineness of Dust on Losses: The fineness of the dust particle increases the loss in two ways: (1) When the bag is clean a greater percentage of it will pass through before the bag seals itself; (2) fine material penetrates farther into the bag pores, building up pressure faster and necessitating more shaking, thereby increasing the loss. The physical principle of operation of the bag filter is simply the separation of solids from a gaseous carrier through a porous medium, and is analogous to the filtration of solids from liquid carriers. Basically, the mechanics of the process are as follows: Fume-laden gases drawn from the operating fur-

Jan 1, 1951

By Arch J. Alexander

This paper is a resume of a study undertaken by the West Virginia Department of Mines. The underlying and direct causes of accidents are determined in each occupational group. Then from this study, accident prevention courses, visual and written, are to be taken to the various working groups in the mines. THE causes of accidents in West Virginia mines follow the main pattern of coal industry accidents in the United States—falls of roof, ribs and face, 56 pct; from haulage, 25 to 30 pet; blasting, 3 pet; electrocutions, 3 pct; explosions, 2 pct; and other causes, about 10 pct. To arrive at some satisfactory conclusions regarding causes and prevention of mine accidents, the Department of Mines has made a study of all mine accidents, from 1945 to 1948, inclusive. During the last two years of this period, we did not have a major explosion, one that took the lives of as many as five men. The direct cause of these accidents is apparent in the reports but we who are making a close study into their frequency think that the virus lies much deeper, and we want to suggest an underlying cause. The rapid growth of the coal industry in West Virginia, the largest producer of bituminous coal, has resulted in a demand for manpower which probably has never been equaled in mining history. At the turn of the century, West Virginia had 24,635 men employed in and about her mines, and they produced 21,153,341 tons of coal a year. In 1948, there were 125,669 men employed, and coal production for the year was 168,589,033 tons, an average increase of 35 pct for each year since 1900. Over 100,000,000 tons of this increase were mined in the southern counties of the state. A safety analyst might read into the history of this development an underlying cause for accident occurrence. He might say that in such a vast, rapid development the available supply of trained miners became exhausted and that young, inexperienced men were employed in the mines by the thousands. Being unacquainted with the hazards of mining, it would be only natural for these young men to be injured or killed in too great a number. This assumption would not be borne out by the records. Men were not injured or killed in disproportionate numbers during their first years in a mine. The only reason we can give is that, during these years, they possessed an attribute of safety—CAUTION—to a much greater degree than in the years following. The coal companies in West Virginia that have been operating over a number of years have a nucleus of employees who have been with them ten, twenty, thirty, and forty years; many of them having gained all of their mining experience with one company. Their habits of work have been

Jan 1, 1951

By H. G. Warrington

Abstract As part of the active development programme pursued by Dominion Magnesium Limited since 1945, a modern extrusion plant was erected and has been in operation for about twelve months. The only source of nigh purity magnesium in the world, Canadian metal is produced by metallurgical processes within the frame-work of the mining industry, which gives a different viewpoint to every phase of production from other world suppliers of commercial grade metal whose operations are based on chemical industries and techniques. The superior properties of corrosion resistance and grain refinement have aided a programme of standardization, reducing the number of alloys supplied in extruded form from seven to four as an aid to economic production. The first big step was the development of a general purpose alloy known as AZ?21x covering all decorative and medium stressed applications, which will supersede two older alloys. Sales approaching a million feet in this alloy show that it bids fair to become the 'mild steel' of the magnesium industry, its applications ranging from terrazzo floor strip to textile machinery and television mast components. In the high stressed field, metallurgical features preclude low-cost extrusion of the older high-strength alloys, but recent development of a magnesium alloy containing zirconium promises an easily workable metal. Hitherto produced by expensive chemical additions, research now shows that the alloy can be produced by metallurgical means, which may make this alloy available for a wide range of commercial applications. Thus the future development programme for extruded products in the form of tube, bars, shapes, and structural angles and channels may evolve two alloys to cover all applications for strengths up to 52,000 lb. per sq. in. Such standardization is the result of taking advantage of the physical and metallurgical properties of high-purity magnesium instead of accepting techniques based on metal produced by older processes.

Jan 1, 1951

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951

By H. Y. Bassett

THIS paper attempts to show the various major operations used in nonferrous tube mills and does not necessarily represent the current practices at the two plants of the Wolverine Tube Div., of Calumet and Hecla Consolidated Copper Co. Inc. The operations now utilized in the production of tubing are quite varied and show the continual interest and advance metallurgically and mechanically to produce the best quality at the lowest cost. Naturally, any advance or lowering of cost is dependent on large production runs, which mean longer machine running time with maximum worker productivity. Standardization of tube sizes and elimination of unnecessary alloys are therefore very necessary, otherwise the development of costly new production machines would be of little benefit to the consumer as a whole. It should be noted that in such a short presentation it is impossible to describe in any detail the major operations. The short descriptions, it is hoped, will enable all who are interested to obtain a general idea of present, day practices in the copper tube producing field. Fig. I is a flowchart or sequence of operations showing the steps usually employed in tube production. RAW MATERIALS Quality starts with the raw material, and it is absolutely necessary that raw material be controlled and held to rigid specifications. Little need be said, however, regarding the raw materials for the casting of bars or billets, as the material always is purchased and checked against the various governing A.S.T.M. specifications. CASTING Casting, as is indicated in Fig. I, is quite varied and for convenience can be classified into two groups: The casting of solid billets, and the casting of hollow tubes, each of which is the base for subsequent operations. In the melting of the raw materials various types of furnaces are used, and the selection of any one is dependent on many factors outside the scope of this paper. However, as of general interest, a short description will be made of each. Induction Furnace (Low Frequency) This is popular in the melting of copper-base alloys, Fig. 2. In the induction furnace the principle of an inefficient transformer is used for the production of the necessary melting heat. The primary coil is.arranged around a transformer core made of high permeability silicon steel sheet. The secondary circuit is through a melting channel around the primary coil and opens into a hearth which contains the main charge. The heat is generated only in the melting channel, but because of the stirring action there is a constant flow of metal around the channel, which when mixing with the charge causes very rapid melting. The volatilization losses are very low as the furnace atmosphere above the charge is heated only by the heat from the melting metal. The stirring action, however, makes the use of any slag cover difficult. Such furnaces- must be started with molten

Jan 1, 1951

By A. L. Engel

In the period of 1942-1945, medium-grade, oxidized, lead-silver ore was mined and shipped from the Diamond district near Eureka, Nev. An encouraging tonnage of low-grade ore was developed during these operations and partly blocked-out for future mining. If the low-grade ore could be treated profitably, further development of the district would result, and production of an important strategic metal might be increased. A representative sample of Diamond district ore was obtained through the Reno office of the Mining Division for the studies described in this report. The sample consisted of lumps and fines of a highly altered siliceous rock containing much earthy red hematite and some granular black hematite. Examination with the binocular microscope showed the lead carbonate mineral, cerussite, in seams and disseminated in the hematite. No zinc or silver minerals were identified, and no sulfide minerals were present. Analyses of the ore showed:

Jan 1, 1951

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By Will Mitchell, T. G. Kirkland, C. L. Sollenberger

The beneficiation of a scheelite ore by flotation was investigated with emphasis on determining optimum conditions for obtaining maximum grade and recovery in the rougher concentrates. Variables such as pH, time, temperature, and pulp density during conditioning were plotted against the grade and recovery of the rougher concentrates. Several gangue regulators were tried, and several methods of cleaning rougher concentrates are described.

Jan 1, 1951

By G. H. Enzian

THE effects of phosphorus and nitrogen on the properties and behavior of low carbon steels are important considerations to both the manufacturer and the user of such material. For one thing, these two elements are the principal points of distinction between the chemical compositions of Bessemer and open-hearth grades. Further, open-hearth steels themselves may vary considerably in nitrogen content depending on the raw materials and ..practice used. In addition, appreciable amounts of rephosphorized open-hearth steels are being used at the present time in some low alloy, high strength grades and in certain other cases. For these and other reasons, it was felt desirable to obtain more complete knowledge of the effects of simultaneous small variations in phosphorus and nitrogen content on such properties of low carbon steel as tensile strength, impact toughness, sensitivity to cold work, and strain aging. A long range investigational program designed to furnish such information, was carried out, and the present paper summarizes some of the data currently obtained. General Discussion The strengthening effect of relatively small amounts of phosphorus in steel has been recognized, and to some extent utilized, for many years. A number of investigators have pointed out, from time to time, that under proper conditions of control, phosphorus can be a useful alloying element in low carbon steels.1-3 Nevertheless, in spite of the volume of data on the subject, the use of phosphorus for this purpose has always been handicapped by widespread feeling that its presence makes the steel brittle, difficult to cold work, and unreliable at low temperatures. This belief on the part of some steel users is not entirely justified in many cases, and often stems from early experience with acid Bessemer steels which have appreciably higher phosphorus (and nitrogen) contents than basic open-hearth grades. Nitrogen in steel, and its effect on properties, has also received considerable attention in the literature.4 In 1906, Braune5 ascribed the brittleness of Bessemer rails to the nitrogen content, and proposed a schedule of nitrogen limits for steels for various uses. This was one of the first papers to recommend directly the use of nitrogen content as a quality control measure, but it did not meet with much favor or support; as a matter of fact, the Jernkon-toret was rather sharply criticized for publishing the paper. In the intervening years a number of papers have been published on the subject of nitrogen in steel. As a result, it is now generally recognized that nitrogen can have an important effect on the properties and behavior of steel and that the presence of this element should be considered in any systematic study of factors affecting steel quality. In 1932, Graham6 introduced the concept that the quality of various steels could conveniently be evaluated and compared in terms of "sensitivity", which was defined as "the characteristic reaction rate of a piece of steel toward brittleness or hardness." This concept formed the basis for a broad research program into factors causing variations in the quality of commercial steels. At an early stage of this work, it became apparent that the observed effect of either phosphorus or nitrogen on the sensitivity of steel depended, in no small measure, on how much of the other of these two elements was also present. Indeed, the combined effect of phosphorus and nitrogen in steel may often be more important than the specific effect of either. With a few exceptions, it is not possible to predict accurately the effect on steel properties of a change in the amount of either phosphorus or nitrogen in the steel without also specifying the approximate amount of the other element. It seems desirable, at this point, to discuss briefly the distinction between strain-sensitivity and strain aging as used in this paper. In the early stages of its development, the work-brittleness test7 (which will be described in more detail later) was used

Jan 1, 1951

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By E. P. McCurdy, W. J. Tait, A. E. Craig

C. M. Marquard—The problem of the automatic control of a grinding-classification circuit is not nearly as simple as has been indicated and it cannot be universally solved through the application of this device. The sound emanating from a ball mill such as the metallic clink of the balls against the liners can at times be misleading. The fact that the sound level due to the balls hitting the liners may be at a minimum does not necessarily mean that the mill is properly loaded. I have in mind an ore we treat that has a soft talcy gangue. The soft fluffy nature of this material makes the sound from the ball mill a most misleading parameter that is worthless as a means for controlling the amount of ore fed to the mill. In every milling plant there are transportation lags due to the time it takes the ore to travel from the mill bins to the ball mill. In many plants there may be several different transportation lags due to varying distances of bins from ball mill. These transportation lags can most seriously affect the operation of a controller. It has been found that under many circumstances the transportation lags can be so bad as to cause the controller to hunt seriously. Hunting can and in many cases does become so serious as to render automatic control impossible because of the surges it causes. While it is possible to compensate for this type of lag, this apparatus does not lend itself readily to accomplish the required compensation. Further, if there are groups of bins at various distances from the ball mill, compensation for one may not be sufficient or may be too great for another. Each milling plant presents a separate problem. The apparatus as presently described does not appear sufficiently flexible to accomplish this. It should be noted that the load on the classifier rakes is determined by measuring the current input to the rake drive motor. Variations in line voltage will

Jan 1, 1951

By B. D. Cullity, J. T. Norton, M. Telkes

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

By H. A. Baumann, T. S. Spicer, C. C. Wright

A LTHOUGH the efficiency of coal utilization has A improved steadily since the turn of the century as a result of continued research and development, little of this increase in efficiency can be credited to improvements in the single retort stoker. There are still numerous problems connected with the burning of coal on this type of unit, the solution of which would be a stimulus to coal and stoker sales and a boon to the user. Among the more critical of these problems is that of burning slack bituminous coal of strong caking tendency and containing large percentages of fine material. With the increased trend toward mechanical mining, it may be expected that in the future an even larger percentage of the coal available for use on this class of stokers will contain higher percentages of the fine sizes, thus aggravating an already serious problem. During the war, the problem of efficient and economic burning of available coals on the single retort industrial stoker, particularly the class 4 stokers (301 to 1200 lb per hr), became quite critical in many localities. In addition to the inherent problems associated with the use of this class stoker, the coals available were frequently not those best suited for use on this equipment and the manpower shortage made it difficult as well as expensive for the consumer to provide the labor necessary to keep the iires in reasonably satisfactory condition. Although exact figures on the number of class 4 stokers are not available, the yearly tonnages of coal consumed are of considerable consequence and have been estimated* at between 15 and 20 million the stoker research staff of the Mineral Industries Experiment Station of The Pennsylvania State College was requested to study the performance of the single retort industrial stoker and to undertake a program of research on the more efficient burning of bituminous coal on this class of unit. Various aspects of overall problem have been investigated since the inception of this program in 1942, only one of which is here reported. General Considerations There are numerous factors which appear directly or indirectly to affect the overall performance of bituminous coal underfeed stokers, such as the caking or matting properties of the coal, the contact relationships between coal and air, the ash fusion characteristics, the burning rate, and the design of the stoker and furnace in which the coal is burned. An analysis of the influence of each of

Jan 1, 1951