Search Documents

By F. S. White, E. L. Kinsella

THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to ' quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,1 showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.2 Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a 1/4-in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontally at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 1/2 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4 1/2-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1952

HIGH-GRADE manganese ore, from which manganese is obtained commercially, is not found in large quantities in any major steel-producing nation in the free world. The U. S. is a "have not" nation with respect to deposits of directly mineable high-grade manganese ore. Known resources of 48 pct Mn or better grade ore amount to less than 200,000 tons. In 1950 the U. S. steel industry consumed 1.8 million short tons of metallurgical grade manganese ore that contained about 800,000 tons of manganese. About 16 pct of the manganese content was lost in processing, so that about 650,000 tons, or 13 pounds per ton of steel actually entered into steel production. Under present practices use expands directly with steel output, and by 1975 the demand in both the U. S. and the rest of the free world is expected to be roughly 60 pet greater than in 1950. In peacetime about 80 pet of manganese consumption goes into steel production; high-manganese steel, dry cells, and chemicals account for the remainder. The manganese supply problem centers around high-grade ore for ferromanganese production. Use of ores containing less than 35 pet Mn sharply increase the costs of making ferromanganese. Use of ferro-manganese of grade below 70 pet in turn requires changes in steelmaking that increase steel cost. Under normal conditions the present small domestic production cannot be expected to increase. Major resources in the U. S. consist of 12 low-grade deposits. The cost of mining and treating these ores to extract a product as good as that yielded by imported ores is at least twice and in some cases more than four times the 1951 price of foreign ores delivered to the U. S. However, as long as trade relations and overseas shipping are not interrupted, deposits in India, Africa, and Brazil can meet steadily increasing demand at approximately present costs. Cost considerations indicate that the U. S. should continue to rely upon overseas sources for its peace-time supply, and that this situation is satisfactory. But, this does not take into account the question of how the U. S. will be able to meet its needs in war. Position of the Rest of the Free World In 1950, free world steel producers outside the United States, with a steel output of 70 million ingot tons, consumed about 1.3 million tons of metallurgical-grade ore. Their manganese ore demand, expected to increase directly with steel production, will by 1975 be about 2.3 million tons. Russia possesses over half the known manganese ore reserves of the world and is producing twice the tonnage of any other country. It supplied more than a third of the U. S. manganese requirements up to 1938 and again in 1948, but by 1950 Soviet manganese exports to the free world had virtually ceased. The free world's supply of manganese now comes mainly from India and Africa. Somewhat over 10 pet of U. S. imports came from Brazil and Cuba. Security Considerations In the event of war the U. S. might be substantially cut off from 90 pet of present sources. Reduction in manganese specifications might cut consumption by over 10 pet without seriously affecting steel quality. By elimination of losses in the production of ferromanganese savings as high as 10 pet might be possible. But, wartime manganese requirements cannot be met through conservation alone. To meet possible future emergencies the U. S. should continue its comprehensive security program for manganese, including stockpiling and research on the economic use of low-grade ore, domestic ores, the recovery of manganese from slag and the reduction of manganese requirements in steel production. If this work, including additional pilot plant operation is pursued vigorously, it should be possible in an emergency to get an adequate supply of manganese from domestic sources. The national stockpile then can be looked upon as a source of supply during the period of at least 2 years required to reach full-scale production from low-grade resources. Ferromanganese Smelting In comparison with smelting of pig iron, ferro-manganese smelting is a very wasteful process. Under present ferromanganese blast-furnace smelting practice, about 8 pet of the manganese in the furnace charge is lost to the slag, and roughly the same amount is lost to the stack gases; the total loss approaches 15 pct. Present practice is a compromise between excessive slag loss and excessive stack loss. In fact, it may be seriously questioned whether conventional blast furnace design is suitable for manganese smelting. U. S. Resources The known manganese deposits of the U. S. contain a total of 3500 million long tons of raw material and 75 million long tons of metallic manganese. More than 98 pct of this contained metal is in 12 large low-grade deposits of which the most important are those at Chamberlain, S. Dak; Cuyuna, Minn.; Aroostook County, Maine; and Artillery Peak, Ariz. Reserves of high-grade ore (48 pct Mn) amount to less than 200,000 tons. About 20 million tons of ore average over 15 pct Mn, and when grade is decreased to 10 pct Mn reserves amount to about 100 million long tons. If cut-off grade is decreased to 5 pet Mn, resources amount to 800 million long tons. Many of these low-grade ores may be beneficiated by flotation or other concentration methods. Pyrometallurgical Methods For smelting ferromanganese, it is essential to have an ore containing at least 50 pct manganese, with an Mn:Fe ratio of about 8:1. Direct smelting of 20 pct Mn concentrates is not promising. The only method that offers any promise involves two-step smelting.

Jan 1, 1952

By J. P. Newell, R. W. Storey

AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery .augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120 This head design proved to be very satis-

Jan 1, 1952

By Edward I. Salkovitz

THE determination of the orientation of metal single crystals and the studies of plastic deformation are greatly facilitated by the use of the stereographic projection. To draw a standard projection of the crystal it is necessary to have a tabulation of the angles between the various crystal-lographic planes of the particular crystal studied. Bozorth' has published such a table for the cubic system which can be found in many reference books; such convenient tabulation for the hexagonal metals, however, does not appear to be in the literature, although scores of workers have calculated these angles. Therefore, Table I of angles for magnesium, zinc, and cadmium has been compiled. Since the c/a ratio is different for each of these metals, three separate calculations are necessary. The angles 4 between (HKIL) and (hkil) were calculated by means of the formula: Hh+Kk+½(Hk + hK)1+~3aLl cos The c/a ratios were calculated from data given in the 1948 edition of Metals Handbook. Fig. 1 is a typical (0001) standard projection of zinc. For all practical purposes, it serves for cadmium as well, as can be seen from the table. For magnesium, however, it is necessary to construct another net. R. M. Bozorth: Physical Review. (1925) 26, 390.

Jan 1, 1952

By Wilbur Jurden

THE writer's first experience with a nonferrous reduction plant of great magnitude was at the Washoe reduction works of Anaconda some 35 years ago. Here was a plant which had been planned with remarkable skill and foresight considering the time and the state of development of copper-plant practice in the year 1902. The designer utilized topography to fullest extent to provide proper sequence of operations and, what is most remarkable, to leave adequate space for future developments, most of which at that time were unknown. However, the practice then was to locate the various units of the reduction works at the most advantageous points of the existing terrain with little regard for tramming or other auxiliaries and then connect these various units by the essential trackage, conveyor systems, piping, etc., as the need developed. This occasionally led to undesirable track arrangements, sharp curves, and steep grades, especially when it became necessary to extend various portions of the plant. Conveyor systems also became rather complicated, running as they did at various angles, and such items as piping and electrical distribution were often found to be in the wrong place, entirely inadequate in size, or awkwardly arranged for any kind of extension. This condition was not peculiar to Anaconda, for all copper plants at that time were built in the same manner and it was the constant association with these difficulties which, in the year 1925, influenced the layout of the Andes Copper Mining Co. plant. In that plant all trackage was laid out straight and level, all conveyors at right angles to each other with minimum length and number of transfers. All buildings were placed parallel and the main structures were complete for all purposes so that auxiliary buildings and dog houses would not be added later. Piping and electrical work was provided for in the original layout and carefully designed to avoid additions and alterations, and careful study given to every movement of material throughout the entire plant so that it would be accomplished with the least possible effort. Naturally it was hardly expected to attain all these objectives perfectly but our efforts did succeed in creating a plant which was unique and outstanding for its time-1927. It was also most gratifying to find that these design principles contributed to considerable savings starting right in the drafting room, carrying through the construction and ultimately yielding savings in operations and manpower. Not only that, but such a plant gives the observer an impression of symmetry and order, is more attractive to the workmen, and unquestionably eliminates many accident hazards. However, the Andes plant buildings were fitted to the existing terrain instead of having terrain created to fit the buildings-an item which we found advantageous to correct on the next large plant. At Morenci in 1939, all of the desirable features of the Andes plant such as parallel buildings, etc., were incorporated; but we went one step further-power shovels were brought in to make the terrain fit the reduction works. The result at Morenci is well-known and needs no elaboration here, but the success achieved by the design methods used for this and previous plants naturally influenced and guided the layout of the Chuquicamata sulphide plant which is the largest yet conceived. Chuquicamata Plant Design At Chuquicamata several factors not encountered previously complicated the problem to a great extent. The most desirable location for the smelter would allow smelter gases to blow directly into the open-pit mine already producing 60,000 tons of oxide ore per day and employing 1550 men. This, of course, would be a serious condition and, therefore, we were forced to move the smelter to a less desirable location but followed our previous experience at Morenci and made the terrain fit the job. The most difficult problem, however, was the provision for receiving various types of ore both by rail and conveyor. These consisted of: 1-Sulphide-bearing residue from the stockpile from which oxide copper had previously been leached. 2-Sulphide-bearing residue coming direct from the leaching vats. 3-Sulphide ore crushed at the existing crushing plants and hauled to the concentrator in cars. 4-Sulphide ore from the new crushing plant adjacent to the concentrator. 5-Sulphide ore obtained

Jan 1, 1952

By S. D. Baumer, P. M. Hulme

B. M. Larsen (U. S. Steel Co., Kearny, N. J.)—Could we have some sort of an estimate on the cost of calcium carbide for this treatment? Also, if you used calcium carbide on carbon-saturated iron, would some effect hold back the reaction? P. M. Hulme (authors' reply)—As far as I know we have not worked on carbon-saturated iron. About 3½ pct C is the highest we have worked on. As far as cost goes, it depends on how much sulphur You have to take out. It will run anywhere from $0.75 to $2.00 a ton overall cost including the cost of carbide per ton of metal treated. That is, using the efficiencies that we show in this paper. We are getting better efficiencies now. T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Did you say 2 lb of calcium compound? Mr. Hulme—That is based on 10 lb of calcium carbide per lb of sulphur removed. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—We have run this type of desulphurization process at the blast furnace. We have desulphurized between 100 and 200 at the blast furnace and taken the iron right out of the furnace with an injector system. The process gave us quite varied results; stratified iron, high sulphur on the top and low sulphur on the bottom, and we decided it was impractical. Mr. Hulme Just what was the type of injection equipment? Dr. Babcock—Nitrogen gas for one injection method and we used fairly large gun equipment. We followed the same general type of pattern you show only on a larger scale. Mr. Hulme—It sounds very much like what we call the gale of wind method. We have very erratic results with that. Dr. Babcock—We have tried several types, and particle sizes. The operation was not satisfactory. Mr. Hulme—Of course, we have never tried it on that scale except on a continuous basis. That is the reason we abandoned the idea of working on 35 ton ladles on a batch principle and took it as it came out of the cupola and treated it on the fly on a continuous basis. Dr. Babcock—When you compare the relative effectiveness of the process as carried out, it does not give a very favorable comparison of that process which is already developed. We did not feel it was worth the

Jan 1, 1952

By G. R. Hodgson, M. P. Lebourg

The introduction in the field of a new type well completion called for the setting of tubing open-ended in the well before perforating the casing. This paper describes a new perforating tool of the shaped charge expendable type, small enough to pass through tubing and powerful enough to perforate the casing. The perforations are produced at an angle and are large enough for optimum production. Performance of this tool in targets and under various well conditions is described. Very often no lifting equipment will be available at the well. In some cases, pressure will exist in the well at the time of the perforating operation (workover wells or multiple trip perforation) ; therefore, new equipment and new technique for the perforating operation were devised. This paper describes this equipment and technique, particularly casing collar recording, sheave support, and cable pull-down device. this last item being necessary for wells under pressure. Results obtained with this tool in the field are given. INTRODUCTION One of the key requirements for the introduction in the field of a new method of permanent well completion was the development of a new perforating method involving the use of a perforating gun small enough to go through tubing and with enough penetrating power to perforate the casing satisfactorily. The equipment described in this paper was basically designed to go through open-ended two-in. tubing and to perforate 5 1/2 in. casing. The equipment is illustrated in accompanying figures. NEW COMPLETION METHOD With the new permanent type well completion, the production string of casing is run and cemented through the potential producing zone. Open-ended tubing is -then run into the well and used to replace the drilling fluid with oil or water. The amount of the oil or water "cushion" can be varied according to the expected bottom hole pressure. Thus, if desired, the hydrostatic head can be greater, equal to, or less than the expected pressure within the zone to be perforated. Mud having been displaced, the tubing is -then positioned so that the end is above the zone to be perforated. The Christmas tree and flow lines are installed and tested. The drilling rig can now be removed from the well since it is not necessary for the perforating operation, thus resulting in a saving in rig tme. The perforating equipment is then moved to the well and the gun lowered through the tubing. After the gun passes out of the open end of the tubing, the depth measurements are correlated with casing collars and the gun placed opposite the zone to be perforated. Upon firing, the gun body is shattered and falls to the bottom of the well. Since the lubricator has been closed before firing, it is possible to withdraw the casing collar locator and head and then open the well immediately to the tanks. DESCRIPTION OF GUN An investigation of two basic types of Perforators, namely a bullet perforator and a shaped charge gun, was undertaken towards the development of a gun to meet the aforementioned requirements. Preliminary tests on various bullet perforator designs within the diameter limitations did not give results encouraging enough to warrant further study. Somewhat better results were obtained by using conventional shaped charges; but, as in the case of the bullet types, the necessarily small overall diameter proved to be a severe limitation and resulted in insufficient penetration. A shaped charge employing a new design was developed which gave excellent penetration. These shaped charges were designed to produce a large hole directed upward at a 45" angle. In order to obtain the maximum space possible for these charges, it was decided to use an expendable carrier made of drillable material, usually aluminum, which would shatter at the time of firing, leaving only harmless fragments at the bottom of the hole. The fixed spacing is five shots per ft. wit11

Jan 1, 1952

By Wilbur A. Haley

The demand on the nation's reserves of high-quality coals suitable for metallurgical purposes is resulting in the rapid depletion of some of the thicker coal beds. These beds are thick enough to permit the use of modern mechanized mining equipment. Many of the thin beds are not being mined at present. In limited areas where the coal is less than 36 inches thick some beds are mined by various conveyor methods. Usually, the room-and-pillar system or some modification of it is used, and often no attempt is made to extract pillars. Consequently, an appreciable quantity of a valuable resource is lost. Many steel companies and coal operators consider reserves of low-and medium-volatile coking coals to be critical, especially in areas where the thin beds are not being mined by modern mining methods. To improve recovery and to promote more-extensive mining in thin beds, methods and devices that are new to American coal mining but applicable to the mining of thin coal beds should be tried. As one of the functions of the Bituminous Coal Mining Section of the Bureau of Mines is to promote improved mining practices and efficiency in the interest of conservation, research in that line is necessary. In 1945 coal planers were observed in operation in Germany by a Bureau engineer member of Solid Fuels Mission to Germany. Planer designs and history of early developments and operations were published. In 1949 an improved planer was again studied by Bureau engineers, and its adaptability to certain conditions in the United States, especially thin beds of friable coal, was considered practicable. After the war the planer was improved, in design and for several years has been operating successfully in the Ruhr. Because of the conviction that the device would be successful, both from the standpoint of conservation and operational prodl1ctivity, under certain conditions in the United States, the Bureau of Mines, through the Bituminous Coal Mining Section, entered into a cooperative agreement with the Coal Division of Eastern Gas & Fuel Associates and Mining Progress, Inc. The purpose of the agreement was to conduct an experiment in modified longwall mining, using a new-type German-built coal plow or planer, known as the Loebbe Habel, supplied by Mining Progress, Inc. The experiment was made to determine if this type of mining equipment operated on a longwall face could be adapted to some of the thinner American coal beds. Such an experiment also would afford many opportunities to study the possibilities and principles of this type of equipment as well as the many factors involved in the mechanical mining of a longwall face.

Jan 1, 1952

By O. Jantti, Erkki Laurila, R. T. Hukki

INVESTIGATION of the methods of analyses for magnetite and ilmenite in the Otanmaki iron-titanium ore and respective mill products has resulted in certain improvements in the methods conventionally employed. The outcome of the investigations is summarized as follows: 1—Development of a diamond-drill core analyser for the determination of magnetic susceptibility of drill cores containing magnetic minerals. 2—Development of a magnetite-ilmenite analyser for pulverized products. 3—Development of a potentiometric method of chemical analysis for the determination of iron, vanadium, and titanium in succeeding steps from one test sample. 4—Proposal for a continuous and automatic magnetite assay method. Diamond-Drill Core Analyser The conventional method of assaying diamond-drill cores consists of splitting the cores, pulverizing them and running chemical analyses on representative samples. The physical properties of magnetic minerals, however, offer an entirely different approach to obtain similar final result by the measurement of respective magnetic susceptibilities in a properly designed instrument. This instrument is shown in Fig. 1. Essentially it consists of a magnetic unit, A, and of a meter unit, B. On top of A is a slot where a piece of diamond-drill core C is visible. The magnitude of disturbance in the original magnetic field caused by the magnetic minerals in the drill core can be observed from the microammeter. This reading is a function of the combined susceptibilities of all magnetic grains in the magnetic field. The magnetic unit is built of E-sheets of a shell transformer, as shown in Fig. 2. The primary coil and two identical secondary coils are wound around the central leg and end legs, respectively. The drill core under examination is placed into one of the air gaps as shown in Fig. 2. The number of ampere-turns of primary coil excited by 50 or 60-cycle ac give a maximum induction of about 600 gauss in the air gaps. The secondary coils are connected in series in the opposite direction. Thus their voltages compensate each other if no drill core exists in the air gap or if the susceptibility of the drill core is equal to zero. As soon as the susceptibility becomes greater than zero, the balance of the magnetic circuit is disturbed, resulting in increased voltage in the terminals of coil 1 and in a respective decrease of voltage in the terminals of coil 2. The voltage difference thus produced is a function of the effective susceptibility of the drill core. If the magnetic grains in the drill core are unevenly distributed, the voltage difference varies as the core is rotated around its own axis. The voltage difference is measured with a Bren-tan0 tube voltmeter. If extreme sensitiveness is desired, the established symmetry of the magnetic circuit does not allow reduction of the 0-voltage difference far enough. Therefore a compensatory voltage of a correct phase taken from the terminals

Jan 1, 1952

By Irving Hartmann

In recent years various modifications in the methods of blasting have been tried as a means of increasing the production of cod and of reducing mining costs. Following an investigation by the Bureau or Mines, authorization was granted to increase the charger limit for permissible explosives par shot hole from 1.5 to 3 pounds under contain conditions; this greatly facilitates the blasting of coal in some cool fields the practice has gradually evolved of simultaneously charging several shot holes in a face and then firing the charges singly without inspecting for gas after each blast. This practice is disapproved by the Bureau of Mines. In other coal mines the explosive chews in several adjacent shot holes are fired simultaneously. This form of shooting is claimed to increase the rate of production, generate smaller volumes of noxious gases, promote the health and safety of workers by eliminating the need of inspection of the face after each charge is fired, produce less float dust, and require less explosive than single shooting. However, simultaneous blasting may have a more harmful effect on the immediate roof strata; in some instances it leads to wedging of the broken coal, thereby making the coal more difficult to load out; it makes misfired shots more difficult to detect and possibly increases the chances of misfires. This lacy be duo to variations in the characteristics of detonators, because of more stringent requirements for adequate firing current, to the need for better electrical connections in the shot-firing circuit, and partly to the inadequacy of present permissible multiple blasting devices.

Jan 1, 1952

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.' It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method' of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author's results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By Robert Glass Cleland

THE OUTBREAK of World War II found Phelps Dodge, thanks to both foresight and good fortune, in a position to increase production of its mines and factories to meet the insatiable military and domestic needs of the times, far beyond all previous records. With the timely completion of the expansion program at Morenci, the company's copper output rose to approximately 447 million pounds in 1942 and to over 478 mil- lion pounds the next year, compared to some 300 million pounds in 1939. To meet the civil and military needs for fabricated cop- per products, the Phelps Dodge Copper Products Corporation carried out an expansion program comparable in size to that of the Phelps Dodge mining operations. It built new plants, enlarged and reorganized those already in operation, multiplied the number of technical experts on its staff, adopted new methods and new machines for the new prod-

Jan 1, 1952

The St. Lawrence Seaway and power project has received the support of the Canadian Parliament, with the House of Commons approving a bill that authorizes the Government to proceed with construction of the seaway, with or without U. S. cooperation. Itogan Mining Co., third largest gold mine in the Philippines, reopened in December under the management of Marsman and. Co. The 'mine was almost totally destroyed during the occupation. The International Materials Conference committee on copper, lead, and zinc has recommended against stockpiling during the: first quarter of 1952 because of the current demands for defense needs. The General Services Administration has told producers who have contracts calling for delivery of copper to the stockpile during the first quarter of 1952 that they do not need to make those deliveries.

Jan 1, 1952

By T. S. Liu, E. A. Peretti

A LITERATURE survey of the In-Sb system, which was made before a study of the binary diagram was undertaken, revealed that the intermediate phase InSb existed and that its crystal structure is face-centered cubic of the zinc blend type. In 1929 Goldschmidt' determined the lattice constant for InSb and obtained a value of 6.452A. A more recent value, 6.461A was reported by Iandelli2 in 1941. The purity of the indium used was not very high, however. The indium used by Iandelli contained 2 pct Ge. In view of this fact it was decided to remeasure the lattice parameter using high-purity indium (99.97+ pct In) and spectrographically standardized antimony of the highest purity available (99.91 pct Sb). Specimens corresponding to the InSb composition were made by carefully weighing the ingredients on an analytical balance and heating them in vacuo in a quartz tube at 700°C. As melting losses were negligible, the alloys were not analyzed chemically, but the intended analysis was taken as being accu- rate. Powder samples were prepared by either filing or crushing of the brittle alloy, followed by screening at 325 mesh. The powders were then annealed at 400°C in evacuated capsules for about an hour. X-ray photograms were taken with a Debye and a back-reflection focusing camera, using characteristic cobalt K. radiation. Lattice parameters were calculated by Cohen's³ method. The results of a Debye pattern and of a back-reflection pattern at 25°C are given in Tables I and 11. The lattice parameter at 25 °C is 6.47602A.

Jan 1, 1952

By H. L. Burmeister

These properties were examined by a Bureau of Mines engineer in 1949. During 1950, these mines were studied by the Bureau to determine the possibility of increasing the production and augmenting the supply of fluorspar. As a result of this study, it was decided to core-drill the Knox-Yingling vein to test the continuation of fluorspar to a greater depth than that reached by mine workings. It also was desired to relate the present deposit with the Rosiclare formation. Development work by the Bureau of Mines was performed from February to May inclusive in 1951. Four diamond-drill holes aggregating 2,733 feet were drilled in the hanging wall of the vein.

Jan 1, 1952

EDUCATION is a business; and, if the consumer is satisfied with the product, no one has any grounds for complaint. "Pretty well satisfied" about slims up the attitude of the mining industry toward the young graduates presently entering the field. Yet, with amazing regularity the controversy over the five-year curriculum recurs in educational circles. The educational mills grind out their products, some higher grade than others, depending on individual proclivity. The cycle continues almost without interruption. Arthur Taggart, however, takes his bowie knife to some of the sturdiest limbs of the tree of knowledge in his article on engineering education on page 770 of this issue. As all who know him might suspect, the pruning is not restrained. With one swing of the knife, such practically-labeled courses as Mine Design are stricken from the tree and transplanted to the field of Graduate Education. Emphasis on the basic sciences and the study of man through courses in history, economics, and literature are recommended to constitute an undergraduate curriculum. Such courses show the least depreciation and therefore give the student the most for his money. Partial justification for this dramatic departure from tradition is explained by the increasing number of companies giving training courses. Why make the student pay for what he can get paid for learning after graduation, the author argues. Other leading educators espouse this doctrine. Dean S. C. Hollister of Cornell, for the Committee on Adequacy and Standards of Engineering Education, recommended to ECPD in 1951 that emphasis be placed on the basic sciences. "Sifting back through the curriculum, it seems clear that instruction in the basic sciences, if taught in a manner such that knowledge of them makes available working tools, contributes the most sustaining part of the curriculum", reported the committee. Note that he would utilize practical problems from the fields of engineering in teaching the sciences. In our opinion the important thing to learn in college is how to think the engineering approach. Recitation on traditional solutions of classic problems sharpens the memory, not the ingenuity of the student. The engineering schools of the nation recognize the advantage of great emphasis on fundamentals, and the inclusion of cultural courses in the curriculum. However, industry presently requires graduates to have a substantial knowledge of the tools of the trade upon graduation. This means that the colleges are forced to pare to the bone to encompass the required studies in the time allotted. In addition, there is the limitation of student money. College educators also claim that entering freshmen are often improperly prepared in such subjects as writing and mathematics. These considerations make it difficult for the critic of the engineering graduate to make any headway with the educators. Actually with the mounting problems imposed by lower grade and more complex ores, a new breed of engineers is needed. The impetus for this new product must come from industry. If there was a concerted effort from industry for an improved type of engineer, the colleges would modify their aims to meet the demand for the kind of individual desired.

Jan 1, 1952

By J. W. Snavely

WITH all the advantages of handling bulk materials by means of belt conveyor also go some problems, one of the most persistent being that of cleaning. When sticky materials are being carried; the build-up of material on the return idler rolls results in difficulty of belt training. Much attention has been given to the problem of cleaning conveyor belts, and a great variety of cleaning devices have been developed. Even the best involve troublesome maintenance, and none can completely remove the fine particles imbedded in the belt cover, which cause rapid wear of the return idler rolls, and at the same time, of the belt cover as well. One of the major rubber companies has been promoting a two-way belt system, in which the conveyor belt is given two successive 90" twists at each end to enable it to carry material in both directions simultaneously. For many years the flat belt transmission industry has installed quarter-turn and half-turn twists in countless numbers of instances. While quarter-turn and half-turn twists in transmission belts is a familiar application, the 180" twist apparently has never been previously attempted with a conveyor belt. About a year ago, two officials of the National Iron Co. of Duluth, Lester and Lewis Erickson, proposed twisting the return run of a conveyor belt on an installation that they were designing for one of the major iron ore producers. Since then the soundness of the idea has been demonstrated, both in theory and by practical test, with the result that the installation of two conveyor belts involving the twisting of the return run is now under way. These two installations are designed to have the return run of the conveyor belt twisted 180" as it leaves the snub pulley at the head drive. The clean underside of the belt is thus placed against the idlers on the return run as well as on the carrying run. Just before it enters the tail pulley, the belt will be twisted an additional 180°, restoring it to its normal position. Because this twisting of the return run of a conveyor belt is a radical departure from accepted practice, an elaborate and extensive test was conducted early in 1950 to demonstrate that this twisting of the return run could be done successfully, also to establish application data for accomplishing this twisting, and to determine if any special equipment would be required. In studying this concept of twisting the return run of a conveyor belt, a number of problems need to be solved, primarily the ones brought about by deliberately introducing an unequal distribution of stress across the conveyor belt and controlling that maldistribution of stress, while confining it to the return run portion. The tension conditions existing in the return run of a conveyor belt are clear to all designers. First, the return run carries the initial or slack side tension of the conveyor belt, the tension that must be supplied to the return run to provide proper frictional contact between the belt and the driving pulley so that the necessary power can be transmitted from the driving pulley to the belt without slippage. This slack side tension is supplied to the belt by means of takeups, either of the gravity type, which can be vertical or horizontal, or by means of the screw type. With inclined or declined belt conveyors the slope tension also must be considered, which is the tension imposed by the weight of the belt hanging from the top pulley. This slope tension frequently can furnish part or even all of the initial tension required. The maximum value of the slope tension will be at the top pulley, and it decreases in direct proportion to the length. In addition to the foregoing, it frequently is desirable to impose arbitrarily additional slack side tension to provide sufficient tension at the loading point at the tail, so that the belt will adequately support its load between the carrying idlers. Design Conditions for Twisting A number of design conditions exist, which must be satisfied successfully to accomplish the twisting of the return run without exceeding normal working limits in any portion of the conveyor belt. It is obvious that the belt edge, in its relation to the center of the belt, must stretch in making a twist, because as the twist is accomplished, the belt edge travels through a longer path than does the center of the belt. It is further obvious that if the edge of the belt is stretched, a redistribution of stress in the belt is required to allow this edge stretching. Moreover, this stress will be unequal across the width of the belt, having a maximum value at the edges, with a minimum value at the- center of the belt. With correct initial tension in the return run of a conveyor belt, the existing slack side tension will be unequally distributed when a twist is introduced. A condition then exists in which the edge stresses,

Jan 1, 1952

An appropriate change in Art. I, Sec. 9, of the bylaws was voted by the Board on April 16 whereby, in the case of Student Associates applying for change of status to Junior Member, only two endorsers are needed instead of three, provided one of them is the same member who endorsed his original application for Student Associateship.

Jan 1, 1952

[ ] Thomas C. Baker, Jr., has been transferred by the American Manganese Steel Div. of the American Brake Shoe Co., from their Oakland, Calif., branch to their Cleveland, Ohio, office. He will represent them in Ohio and Michigan. William H. Carson, has been appointed district manager of Goodman Mfg. Co's. Huntington, W. Va. sales office. He succeeds Morris W. Highland, granted a leave of absence for health reasons. Mr. Carson, a graduate engineer of Michigan College of Mining & Technology, has been a member of the company's Huntington sales force since 1939, the past two years as assistant district manager. James Parnell Caulfield, former general manager of the Utah Copper Div. of Kennecott Copper Corp., has been appointed assistant general manager of Kennecott's Western Mining Div. L. F. Pett, general supervisor of operations of the Utah Copper Div., was named Mr. Caulfield's successor as general manager. William D. Charles, on completion of his graduate studies at the Massachusetts Institute of Technology, accepted the position of mineral engineer with American Cyanamid Co.

Jan 1, 1952

By R. W. Huber

While conducting an investigation on electrolytic reduction of magnesium oxide in 1943, it became necessary to obtain accurate data on the conductivity and density of various mixtures of fused chlorides. AZ the required information was not available in the technical literature, or there were inconsistencies in the data from several investigators, an independent study was made at the Bureau of. Mines laboratory at Salt Lake City on the conductivity and density of the molten chlorides MgCl2, CaCl2, BaCl2, KCl, and NaCl and the binary mixtures of MgCl2 with the other four chlorides. Studies were also made on the binary system KCl-CaCl2 and on certain portions of several ternary systems. Measurements covered a temperature range from the melting point to 1,000° C. The results of this study were reported in an intra-Bureau report prepared early in 1944. Since then the Bureau of Mines has received several requests for data on fused chlorides; the results of the previous study, therefore, are being published to make the data available.

Jan 1, 1952