Search Documents

By V. T. Stringfield, H. H. Cooper

ONE of the earliest investigations of ground water in Florida was made in 1513 when Ponce de Leon arrived at St. Augustine in search of the Fountain of Youth. The history of the development of the water resources of the State shows that the large artesian reservoir that underlies Florida was discovered in the latter part of the last century. Part of that history is given by L. C. Johnson' who states that the first successful artesian well in Florida was drilled at St. Augustine between 1880 and 1882. After the City of Jacksonville failed to obtain a flow of artesian water at a depth of nearly 400 ft and abandoned the drilling, R. N. Ellis, City Engineer, and L. C. Johnson, using Johnson's knowledge of the geologic structure of the artesian reservoir, estimated correctly that artesian water could be obtained at a depth of about 500 ft. Thus began the development of the large artesian system in the northeastern part of the State. In 1908, the Florida Geological Survey issued its first report on the ground water of central Florida. More recent reports give the results of investigations that have been in progress in cooperation between the Florida Geological Survey and the U. S. Geological Survey since 1930. As a result, the ground-water geology and hydrology of Florida are now so well known that ground-water problems such as confronted early investigators no longer exist. However, new problems arise and new discoveries are made as the demand for more ground water increases with the development of the State. Water-Bearing Formations Descriptions of the geologic formations and a map showing their distribution at the surface are given in a recent report by Cooke.' The geologic formations that yield the ground-water supplies in Florida represent only a small part (about 1000 ft) of the total thickness of the sedimentary rocks (more than 15,000 ft) that underlie Florida. The water-bearing rocks that yield fresh water include more than two dozen formations that range in age from Eocene to recent. The Eocene formations, which consist chiefly of limestone, are the oldest and the deepest of the formations in Florida that yield fresh water to wells. In 1944, on the basis of a study of the foraminifera, the Applins -ivided the limestone of Eocene age into six formations, which are as follows, from top to bottom: Age or group Formation Jackson Ocala limestone icAvon Park limestone Claiborne -j Tallahassee limestone aLake City limestone Wilcox Salt Mountain limestone xOldsmar limestone The Ocala limestone and the underlying formations of Claiborne age, along with some of the overlying limestone of Oligocene and Miocene age, constitute the principal source of water in Florida and southeastern Georgia and generally may be regarded as forming one artesian aquifer or water-bearing unit. This aquifer is referred to in this paper as the Floridan aquifer, a name proposed by Parker.' In part of Seminole County alone more than 1000 flowing wells yield water from the Floridan aquifer. A yield of 6500 gpm, or about 9.5 million gal per day, by natural flow from a well penetrating the aquifer at Jacksonville, Florida, was observed in 1942. A yield of about 7000 gpm by natural flow was reported for a well 1390 ft deep at St. Augustine in 1887. The largest yield reported from a pumped well penetrating the aquifer is 7500 gpm, or about 10.5 million gal per day. The aquifer is also the source of some of the large springs, such as Silver Springs, whose discharge, according to measurements made by the U. S. Geological Survey, has ranged from 526 to 1350 sec-ft, or from 340 to 872 million gal per day. The top of the Ocala limestone, as represented by contours in Fig. 1, indicates in a general way the geologic structure of the formations that comprise the Floridan aquifer. The Ocala is at or near the surface in the areas represented by shading in the northwestern part of the peninsula and also in an area in western Florida adjacent to Alabama and

Jan 1, 1952

By Howard E. McKinney

A high-pressure wellhead lubricator has been developed to facilitate telemetering electrical measurements from subsurface reservoirs to the surface with the well under normal flowing conditions. The field unit in use at the present time employs a 5/16-in diameter, single-conductor armored cable and is to be used in wells with surface pressures up to 5,000 psi. It has a pressure sealing element that maintains a continuous and absolute seal around the cable as it enters or leaves the tubing at speeds up to 175 ft per minute. A cable injecting device is used which obviates sinker bars or weight sections on the instrument. INTRODUCTION The development of instruments for securing physical measurements in pressure wells has been confined in the past to those instrument which would operate on a wire line and record the necessary measurements in the downhole instrument itself, or those which would operate on an electric cable in a well with the surface pressure killed by the use of weighted fluids or by the use of tubing plugs. In one case the accuracy of the measurements is questionable, and in the other the range of application is very limited. Considerable work has been done by other interests to provide effective means to accomplish the necessary telemetering. The U. S. Bureau of Mines developed a wellhead lubricator prior to 1947 which permitted a 5/16-in diameter single-conductor cable to be lowered into a well with a surface pressure of approximately 500 psi. This unit was used successfully in a number of tests in Oklahoma. A company which tests wells has recently offered on a service basis a wellhead lubricator with a 3/16-in diameter cable that reportedly operates up to 2,500 psi surface pressures. Each of the above operates on a staging principle to effect a seal. In both of these units some leakage of well fluid occurs when the cable is moved. SPECIFICATIONS FOR DESIGN In order to provide the maximum flexibility in its use, the following parameters were established for the design of our high-pressure wellhead lubricator: L An absolute well fluid seal up to 5,000 psi surface pressures. 2. Means for raising and lowering the instrument at speeds of at least 100 ft per minute. 3. Provision for the instrument to enter and leave the well without disturbing the well flow or the reservoir conditions. 4. A cable large enough to provide suitable electrical characteristics and suitable mechanical properties. 5. A method of operation that will not damage the well in any way. The present high-pressure wellhead lubricator field unit fulfills the above requirements. DESCRIPTION OF THE UNIT AND ITS OPERATION The cable selected for this use is the standard Amergraph 1H2 as manufactured by the American Steel and Wire Co. This particular cable is normally used by the Halliburton Oil Well Cementing Co. in their conventional well logging operations. Although the cable presents a noncircular cross-section (Fig. l), its diameter is very consistent; lor example, maximum diameter is 0.325 in., minimum diameter 0.314 in. This [actor permits the use of the sealing element, as later described. Early in the development of the high-pressure wellhead lubricator it was apparent that we could not effect a direct gas seal around a moving 1H2 cable. This becomes evident when an examination of the cable cross-section is made. The voids between the strands of the outer armor provide natural channels lor the flow and escape in large quantities of a low-viscosity fluid such as gas. However, it is relatively simple to

Jan 1, 1952

By K. John

"THE most recent estimate of minteable coal reserves in Saskatchewan was made by the Federal Royal Commission on Coal (1944- 6). Saskatchewan was then estimated to have some 24 per cent of the Canadian reserves and two-thirds of this is located in what is called the Souris-Estevan area, which lies in the southeast corner of the Province and border's on the International boundary. It is also estimated that there are some 61/2 million thousand-tons in this area of lignite coal which grades 8,000 B.t.u. or less and has a moisture content ranging from 30 to 33 per cent. Ownership of coal rights in the Province is widely dispersed between the Crown, individuals, and corporations, and a recent survey disclosed that 40 percent of ownership was vested in the Crown and 60 per cent in private individuals and corporations. Coal rights on Crown lands may be leased at an annual rental of $ 1.00 an acre. Under such leases, a royalty of 5 cents a ton is levied on all coal mined. A royalty of 7 cents a ton is levied on coal produced from lands where mineral rights were purchased from the Federal Government prior to the transfer of jurisdiction over natural resources to the Province, in 1931. An annual mineral tax of 50 cents per acre has also been imposed by the Provincial Government on all coals within a defined producing areas."

Jan 1, 1952

Development: Iron Ore In Peru Utah Construction Co., of San Francisco and a Peruvian Government corporation have signed an agreement for development of a large iron orebody in Peru. Most tests show 60 pct iron or better. Most of the ore is magnetite. Although ore will be shipped mainly to Eastern U. S. blast furnaces, shipments to the West Coast may develop as the orebody opens up. The construction firm indicated three American steel companies have shown interest in the project. The orebody is located 300 miles south of Lima and about 15 miles from the coast at the same longitude as New York City. Allen D. Christensen, executive vice-president of Utah Construction noted that the distance is shorter between Peru and the East Coast. The ore deposit measures about four to five miles in one direction and 10 miles in the other. As many as 15 outcroppings within these limits have been reported. Several of the outcroppings are thousands of feet long by several hundred feet wide, Christensen said. Shipments between 100,000 and 200,000 tons of ore per month are projected by the company. Cost of opening the mine to production may go over $5 million, Christensen said. It would include building of docks for ocean going vessels, housing, and heavy duty mining and processing equipment. The contract with the Peruvian government gives Utah Construction six to eight months for additional tests and a 20 year concession for mining the orebody. Peru will collect royalties on all ore. The company will also supply about 300,000 tons per year for an electric furnace to be installed by the Peruvian Government at Chimbote. No steel is produced in Peru now. Utah Construction formed the Argonaut Mining Co. last year, and was shipping iron ore from British Columbia to Japan at a rate of more than 50,000 tons a month, before winter weather decreased operations.

Jan 1, 1952

By R. E. Zimmerman

D. R. Lyons (Republic Steel Corp., Cleveland)— Some tests using wet tables conducted by an operating company to determine the effect of table-water density on the quality of the washed coal should be of interest. The only variable during the testing period was the percentage of solids in the table water. Table operating data are shown in Table XV. The ash content of the washed coal remained constant or nearly so, as the percentage of solids varied while the sulphw content of the washed coal decreased as the percentage of solids increased.

Jan 1, 1952

JAMES A. BARR Consulting Engineer Mt. Pleasant; Tennessee Washington, D.C. BEHRE DOLBEAR G COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia LENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.

Jan 1, 1952

By B. R. Coil, C. A. Ross

NEW demands for underground power in the Miami mine of the Miami Copper Co., Miami, Ariz. has brought about expansion of the distribution system for both ac and dc power. Progress in mining equipment and the normal changes in the mine were responsible for this increased demand. Early power requirements were for pumping and haulage. A 440 v ac power line down No. 5 shaft took care of a small pumping load and shaft station lighting, 275 v dc power was generated by motor generator sets on the surface, with a churn drill hole from surface to the 570 haulage level serving as a cableway. Electric lights were installed where power was available, and thus were confined to the haulage level and shaft stations. All industrial power in the Miami area is 25-cycle, which dates back to the hydroelectric generator installation at Roosevelt Dam in 1908-10. The Problem The main haulage level was moved to the 720 level and later, to the 1000 level, requiring a longer feeder line with the resultant voltage drop. Also, as mining progressed to the east, the churn drill hole for the power cable would have been subjected to subsidence cracks. The first extension in the use of electricity was in electric blasting. About 1935 the mine went to electric blasting, using the dc haulage current. Bringing electric current to the working levels of the mine for blasting greatly expanded the use of electric lights. Lights were used in tool rooms, powder and cap magazines, stairways, and other semi-permanent installations. Like all mines, Miami Copper began to study and experiment with mechanical mucking and transportation of ore by slushers, shakers, and belts during the late 1930's and early 1940's. At the beginning of the program, power was supplied from the haulage level 275 v dc system. Later it became necessary to run a cable, carrying 440 v ac power, down the No. 7 ventilation shaft. The increased use of power came about gradually, and many new problems were added, not the least being the introduction of switch boards and power cables into the working areas of the mine, where drifts and crosscuts take weight, and require repairs. The 25-cycle current presented special problems, in that 25-cycle transformers are twice as large and about 2V2 times as heavy as 60-cycle transformers of the same power output. The 25-cycle transformers were considered too large for installation in the mining areas. In 1947 the distribution system was revised and standards were adopted, governed by the following

Jan 1, 1952

By W. H. Triplett

THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno, y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold. mines are situated a few kilometers to the southeast on the same mountain range near Concepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burckhardt, E. Böse, L. B. Kellum, .and R. W. Imlay. Carlos Burckhardt who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1952

The Industrial Minerals div. has been forging ahead in formulating a program for the February Annual Meeting in Los Angeles. Several papers have been listed and more are being worked into the program. For the cement, lime and gypsum part of the sessions, papers on Gypsum in the Aircraft Industry, Geology of San Marcos Island Gypsum Deposit, and Status of New Dry Rotary Blast Hole Drills, are expected. The Chemical Raw Materials sessions will feature a symposium on potash, with 13 papers as the anticipated number to be presented. Airborne and Ground Magnetometer Work has been suggested. Eight papers have been set for Mining Geology, Four papers, Mining Phosphate Rock, Idaho Phosphorous, and Geology of Carlsbad Potash and Geology of Pearlite will be on the program. Sessions on Dimension stone and slate have been tentatively worked out with papers on Geologic Factors Affecting the Dimension Stone Industry of California, A Quarter Century of Granite Quarrying in Massachusetts, Rock Bursting and Other Geologic Problems in the Granite Quarries of Barre, Vt., Quarry Practices in the Indiana Building Stone Industry, Stratigraphy and Composition of the Salem Limestone, and Dimension Stone in the U. S. in 1952. The Rare Minerals Committee is aiming for six papers with two papers now definitely on the program.

Jan 1, 1952

By Paul A. Beck

THE occurrence of the (100) [lOO] or "cube" texture upon annealing of cold-rolled copper has been much investigated.' The conditions favorable for its formation were found to be a high final annealing temperaturez or long annealing time," a high reduction of area in cold rolling prior to the final anneal,' and a small penultimate grain size." The effects of penultimate grain size and of rolling reduction were found by Cook and Richards4 to be interrelated in such a way that any combination of them giving lower than a certain value of the final average thickness of the grains in the rolled material leads to a fairly complete cube texture with a given final annealing time and temperature. Also, according to the same authors, at a higher final annealing temperature a larger average rolled grain thickness, i.e., a lower final rolling reduction, is sufficient than at a lower temperature. These somewhat involved conditions can be understood readily on the basis of recent results obtained at this laboratory. Hsun Hu was able to show recently by means of quantitative pole figure determinations that the rolling texture of tough pitch copper, which is almost identical with that of 2s aluminum: may be described roughly as a scatter around four symmetrical "ideal" orientations not very far from (123) [112]. In the case of aluminum, annealing leads to retain-ment of the rolling texture with some decrease of the scatter around the four "ideal" orientations, and to the appearance of a new texture component, namely the cube texture." A microscopic technique, revealing grain orientations by means of oxide film and polarized light, showed that the retainment of the rolling texture is achieved through two different mechanisms operating simultaneously, namely "re-crystallization in situ," and the formation of strain-free grains in orientations different from their local surroundings, but identical with that of another component of the rolling texture. Thus, a local area in the rolled material, having approximately the orientation of one of the four "ideal" components of the texture, partly retains its orientation during annealing, while recovering from its cold-worked condition, and it is partially absorbed at the same time by invading strain-free grains of an orientation approximately corresponding to that of another "ideal" texture component. The reorientation here, as well as in the formation of the strain-free grains of "cube" orientation, may be described as a [Ill] rotation of about 40°, see Fig. 1 of ref. 6. The preferential growth of grains in such orientations is a result of the high mobility of grain boundaries corresponding to this relative orientation.' " It appears very likely that in copper the mechanism of the structural changes during annealing is similar to that observed in aluminum (except for the much greater frequency of formation of annealing twins in copper). In both metals the new grains of cube orientation have a great advantage over the new grains with orientations close to one of the four components of the rolling texture. This advantage stems from their symmetrical orientation with respect to all four retained rolling texture components of the matrix; they are oriented favorably for growth at the expense of all of these four orientations. As a result, the growth of the "cube grains" is favored over the growth of the others, as soon as the new grains have grown large enough to be in contact with portions of the matrix containing elements of more than one, and preferably of all four component textures. It is clear that this critical size is smaller and, therefore, attained earlier in the annealing process if the structural units, such as grains and kink bands, representing the four matrix orientations are smaller, i. e., if the average thickness of the rolled grains is smaller. Hence, for a given annealing time and temperature, a smaller penultimate grain size and a higher rolling reduction both tend to increase that fraction of the annealing period during which the above condition is satisfied. Consequently, the percentage volume of material assuming the cube orientation increases. The same is true also for increasing time and temperature of annealing when the penultimate grain size and the final rolling reduction are constant, since the average size attained by the new grains during annealing increases with the annealing time and temperature. For the same reason, at higher annealing temperatures a given volume percentage of cube texture can be obtained with larger rolled grain thickness (larger penultimate grain size, or smaller rolling reduction) than at lower annealing temperatures. The well-known conspicuous sharpness of the cube texture may be interpreted as a result of the fact that selective growth of only those grains is favored that have an orientation closely symmetrical with respect to all four components of the deformation texture and exhibit, therefore, a high boundary mobility in contact with each. The effect of alloying elements in suppressing the cube texture, as described by Dahl and Pawlek,' appears to be associated with a change in the rolling texture. For face-centered cubic metals, such as copper, which do exhibit the cube texture upon annealing, the rolling texture is always of the type described above, i. e., scattered around four "ideal orientations" of approximately (123) [112]. The addition of certain alloying elements, such as about 5 pct Zn or 0.05 pct P in copper, has the as yet unexplained effect of changing the rolling texture into the (110) 11121 type. This texture consists of two fairly sharply developed, twin related components. In such cases, as in 70-30 brass and in silver, the annealing texture again is related to the rolling texture by a [lll] rotation of about 30°, however, because of the different rolling texture to start from, it has no cube texture component. At higher temperatures, both in brassm and in silver," grain growth leads to a further change in texture: A [lll] rotation of the same amount, but in reversed direction, back to the original rolling texture.

Jan 1, 1952

By Fred D. DeVaney

DURING the past few years a radically new process for the magnetic roasting of iron ores has been investigated and developed by Pickands Mather & Co. and the Erie Mining Co. in the Erie laboratory at Hibbing, Minn. This process, originally devised by Dr. P. H. Royster of Washington, D. C., involves the use of a roasting technique quite different from older methods. It has now been demonstrated that iron-bearing materials can be roasted as effectively as by any previously known method, and at a much lower cost. The increasing shortage of highgrade iron ores in this country has accelerated the search for new methods that would permit low grade materials to be utilized. The concept of magnetically roasting low grade nonmagnetic ores such as the oxidized taconites and then separating such material magnetically has always had considerable appeal. The magnetic concentration idea is attractive because of the sharpness of the separations and cheapness of the method. Heretofore, however, the equipment and the processes available for the magnetizing-roasting -step have left much to be desired. The customary equipment available for reduction roasting has been: 1-multiple hearth furnaces, 2-rotary kilns, and 3-shaft type kilns. In addition, it is understood that some work has been done in magnetically roasting fine ores by a process using the FluoSolids principle, but little information on this process is available. The multiple hearth kiln has been used the most but first costs and operating costs have been high because of low capacity, high maintenance, and poor gas utilization. Magnetic roasting can be done in a rotary kiln, but the radiation losses are high and the conversion to magnetite is usually unsatisfactory because of poor contact between the gases and the solids. Of the shaft-type furnaces, probably the most efficient yet developed is that designed by E. W. Davis of the Minnesota Mines Experiment Station. This furnace was operated at Cooley, Minn., during 1934-1937 but was abandoned in 1937 because the operation was uneconomic. Heretofore the basic concept behind most magnetic roasting processes has been the idea of heating iron ore to a temperature of 800° to 1100 °F in a strong reducing atmosphere, preferably either carbon monoxide or hydrogen. Temperatures under 800°F were undesirable since excessive roasting time was required. Temperatures over 1100°F were avoided because of the danger of converting part of the iron to ferrous oxide which is nonmagnetic. In the new roasting process, the operation is carried on in a shaft furnace using a controlled atmosphere containing a low percentage of reducing gas. The temperature in the roasting zone is considerably higher than with the usual reducing gas and this speeds up the reduction time. Portions of the spent furnace gases are cooled and recirculated and this together with the good contact between ore and gas makes for high reducing gas utilization. High heat economy is secured by recuperating heat from the roasted ore by passing the cold reducing gases countercurrent to flow of ore. The heat transfer principle is similar to that employed in a pebble stove and to that used in the Erie Mining Co. furnace at Aurora, Minn., for pelletizing fine magnetite concentrates derived from taconite. The theory of controlled atmosphere during the roasting operation can best be appreciated by inspecting the equilibrium diagram of the Fe-C-O system shown in Fig. 1. An inspection of this diagram shows that in certain areas magnetite, Fe3O4, is the only stable form of iron. A further inspection of this table shows that if the proper ratio is maintained between carbon dioxide to carbon monoxide, such a gas will be reducing with respect to hematite, Fe2O3, and will be oxidizing with respect to both ferrous oxide, FeO, and iron, Fe. It should be kept in mind that the formation of ferrous oxide in a roasting operation is harmful, since this oxide is nonmagnetic; if it forms in any quantity, it will cause substantial loss of iron in the ensuing magnetic separation step. If a ratio of approximately three parts carbon dioxide to one of carbon monoxide is maintained, the resulting operation can be carried on at a relatively high temperature without fear of over-reduction. Specifically, most of the tests in the Erie furnace have been made at a temperature of 1500° to 1600°F, with an entrant gas containing approximately 5 pct carbon monoxide and 15 pct carbon dioxide, with the remainder largely nitrogen. It should be remembered that the ratios of carbon monoxide to carbon dioxide shown in Fig. 1 hold even though the bulk of the gas is an inert gas such as nitrogen. It may surprise many to learn that a gas containing as low as 3 pct carbon monoxide, and 12 pct carbon dioxide with the remainder nitrogen is an extremely effective reducing gas in the 1000° to 1600°F temperature range. The reducing gas is not limited to carbon monoxide, and mixtures of hydrogen and carbon monoxide may be used effectively, provided that a similar ratio is maintained between the reducing gases and carbon dioxide and water vapor. For a more detailed explanation of the theory involved, the reader is referred to U. S. patents 2,528,552 and 2,528,553. From a safety standpoint, the weak reducing gas used in the furnace offers an advantage. Its composition is such that it is well below the limits of explosion should air enter a hot furnace. This condition is not true with the usual reducing furnace, in which a gas rich in carbon monoxide or hydrogen is used. The general furnace design and method of operation may best be understood by an inspection of

Jan 1, 1952

By C. L. Prokop

A laboratory investigation has been made of the effects of mud hydraulics upon the formation and erosion of mud filter cakes. The tests were conducted to simulate drilling conditions as nearly as possible. The formation of mud filter cake in a drilling well does not proceed at a uniform and unbroken rate. Instead, the rate of cake accumulation depends upon whether or not the mud is being circulated. If the mud column is quiescent, filter cake formation is a smooth function of the filtration characteristics of the system. If the mud is being circulated filter cake formation depends not only upon the filtration characteristics of the mud but also upon the erosive action of the flowing mud column Filter cakes formed during continuous mud circulation were observed to reach an equilibrium thickness after several hours' circulation. Mud circulation was maintained at a constant volumetric rate throughout each experiment. The fluid velocity at equilibrium cake thickness was dependent upon the thickness of the filter cake. Muds having exceptionally high water loss deposited thick filter cakes in spite of very high eroding velocities. The muds having good filtration characteristics deposited thin filter cakes at equilibrium circulating velocities well within tile range of those in a drilling well. It was observed that filter cakes deposited during stagnant filtration were quite difficult to erode by mud circulation. The - rate of crosion computed from the rate of filtrate accumulation after equilibrium cake thickness had been reached was in reasonable agreement with the rate of erosion obtained by direct observation. Continuous mud circulation usually caused the permeability of the filter cake to decrease with time. INTRODUCTION Many of the difficulties encountered during tile drilling of a well have been attributed to the loss of water from the mud and the attendant deposition of solids upon the walls of the hole. Past experience has shown that a reduction of the filtration rate of the drilling fluid eliminates or greatly reduces these difficulties. Definite filtration requirements, however, are hard to establish for a given set of conditions. This is due. in part, to the fact that the usual filtration test performed upon mud doe? not simulate well conditions as closely as desirable. The filtration characteristics of a mud are customarily determined by means of the standard low-pressure API wall-building tester.' In this instrument a filter cake is deposited upon a horizontal bed under a pressure differential of 100 psi. The rnud is quiescent during the filtration period. In actual practice. mud filtration occurs within a well under quite different conditions. One of the major differences is that mud flows upward across the filter bed as the filter cake forms. This undoubtedly produces a change in the filter cake which cannot be reflected in the results of the API test. The laboratory work described in this paper had as its primary objective a better understanding of the influence of mud circulation upon the thickness and ,characteristics of the filter cakes deposited under conditions similar to those existing in a drilling well. ANALYSIS OF PROBLEM Once a permeable formation is penetrated by the bit, filtrate from the mud flows into the formation. 'he mud solids plaster against the walls of the hole, forming a filter cake. If the mud column is stagnant, that is, if it is not being circulated. the filter cake will increase in thickness until the hole is filled. Prior to the time that the hole is filled, the thickness of filter cake existing at any given time will be a function of the filtration characteristics of the mud, the temperature, and the pressure differential. The effects of these variables have been investigated in the past for both flat bed filtration2'3 and for radial filtration.' When the mud is circulated in a hole in which a filter cake i. being deposited. some of the solids that would ordinarily deposit in the filter cake will be carried away by the eroding action of the mud. This will limit. filter cake thickness. Some work has been done to determine the effect of flow upon the filtration rate in a circulating mud system' but little work has been done upon the factors which determine the filter cake thickness existing in a circulating system. On first sight it would appear that the major factors controlling filter cake formation in a circulating system should be: 1. The rate of deposition of solids from the mud. 2. The erosive force that the flowing mud exerts upon the filter cake. 'A. The erodabilitv of the filter cake. 4. Any change in filter cake characteristics attributable to the scouring action of the mud. The rate at which solids are deposited from the mud will be controlled to a large degree by the filtration characteristics of the mud, the pressure differential. the temperature under

Jan 1, 1952

By Pol Duwez, Spencer R. Baen

A LTHOUGH the practical importance of Fe-Cr--iV Mo alloys has long been recognized, constitution studies have been limited to a few alloys within rather narrow ranges of composition. The purpose of the present study was to establish the phase boundaries in the ternary diagram at a temperature of 1200°F (650°C).* The identification of phases and the determination of phase boundaries were based primarily on X-ray diffraction measurements and occasionally on microscopic observation. The methods used for locating the phase boundaries were essentially those described in detail by Andersen and Jette,' and by others.', The compositions of 180 alloys, prepared by powder metallurgy techniques, are shown in Fig. 1. The chemical analysis and mesh size of the powders which were used for the preparation of the alloys are given in Table I. The powders were mixed for 48 hr or longer, then compacted under 80,000 psi in a %-in. diam steel die. Each specimen weighed approximately 5 g. The compacts were sintered for 4 hr at 2500°F (1371°C) in an atmosphere of pure dry hydrogen (dew point near the temperature of liquid nitrogen). An open tray of chromium powder was placed upstream of the compacts to act as a "getter" for the last traces of oxygen or water vapor. In many cases this chromium powder was bright after sintering. Occasionally the upstream side of the powder was slightly greenish, but in all cases the downstream side was metallic. Some of the alloys contracted during sintering and some expanded as much as 20 pct. The latter alloys, which in all cases were brittle, were crushed in a tool steel mortar, repressed, and resintered for 4 hr at 2500°F. After sintering, the alloys were aged for ten days at 1200°F (650°C) in evacuated (105 mm Hg or better) fused silica tubes and were cooled rapidly to room temperature following the aging treatment. The use of the powder metallurgy technique in preparing alloys for structural investigation offers a simple method 'of avoiding contamination or non-homogeniety which could result from a melting operation. It is very often possible to dispense with chemical analysis of the alloys which have been prepared by the powder metallurgy method. In lieu of chemical analysis, it is necessary to determine the weight of the compact before and after sintering. The chemical composition of the alloy may be considered as that of the green compact, within the limits of accuracy determined by the loss of weight during sintering. In phase-diagram studies it is important to achieve homogeniety in structure, whether the alloys are prepared by powder metallurgy or by melting. Homogeniety means complete diffusion during the sintering of the alloys which are prepared by powder metallurgy. It has been found from experience that the best criterion for establishing the completeness of diffusion is the sharpness of the X-ray diffraction patterns. This criterion has been used throughout the present study. The X-ray diffraction data were obtained using powder cameras of either 214.86 or 71.62 mm diam. Copper, cobalt, or chromium Ka. radiation was used, the choice being based on the alloy composition. The powder samples were obtained by filing or crushing, depending on whether the alloy was ductile or brittle. In some cases, the powder was annealed for 4 to 6 hr at 1200°F in vacuum. The measurements were corrected for film shrinkage and absorption. The large camera, in which the film is mounted

Jan 1, 1952

Roof Bolts An expansion shell and plug Westinghouse roof bolting assembly made for use with threaded steel rods and large flat washers or steel channel employs a plug larger in diameter than those for trolley wire service. The notched plug helps prevent shell and plug from turning. The unit is shipped complete. Circle No. 1 Fan The Jeffrey Mfg. Co. Aerodyne Midget fan is a self contained blower or exhauster for auxiliary ventilation through tubing. Operating rating with 5 hp motor is 6.5 in. maximum static pressure, and 6200 cfm free delivery volume. Weight is 340 to 475 lb and it may be furnished in open or permissible form. Circle No. 2 Heavy-Density Initial installation in the Mesabi Range country of the Wilmot-Daniels heavy-density concentrating system was a 175 ton per hour plant at the [ ] Skubic Bros. Virginia, Minn., operation. This Wilmot Engineering Co. unit has a separatory vessel providing unidirectional medium flow and as the only moving part uses a standard drag-line conveyor for lifting sink out of the bath. Circle No. 3 Portable pH Meter A low priced battery-operated portable pH meter of utmost simplicity announced by the Photovolt Corp. uses only 3 ordinary radio batteries which give over 2000 hours of service. Accuracy of 0.03 pH is claimed by the manufacturer for the model 125, and AC power line supply is available. Circle No. 4

Jan 1, 1952

By Donald L. Mordell

Introduction A very large part of the world's fuel resources are in solid form, as various grades of ?coal, but an increasing proportion of fuel demands on this Continent and else-where are having to be met by liquid fuels. Convenience and, in many cases, cost weigh heavily in favour of the liquid: fuels, and there are many fuel burning applications where the use of coal would be impractical, such as for automotive or air transport. By extrapolating the present trends one might conclude that, in future years in Canada and the United States, coal will be used only in a few power stations close to coal fields. If such a state of affairs should arise, it will obviously prove embarrassing to those accustomed to make their livelihood from the winning and marketing of coal, but it is perhaps not so obvious that it must also prove an embarrassment to the nation. The major reasons for this are two in number. Firstly, if present coal production is to be replaced by oil production, a large capital expenditure is necessary, which must inevitably be paid by the consumer; and secondly, in times of emergency, large amounts of oil fuels are required for military purposes which cannot be achieved with solid fuels. It is obviously unwise, therefore, to discontinue the use of coal for those non-military jobs that it can do. If we examine the major fuel markets we find that there are three: Domestic heating Steam generation Transport by air, sea, and land For domestic heating, the extreme convenience of oil, in spite of its greater cost, has captured much of the coal market.

Jan 1, 1952

By Louis Frost

"Dominion No. 17 Colliery, of the Dominion Coal Company, Limited, is located in the district of New Victoria, N.S., at the entrance to Sydney harbour.This Colliery was opened in 1882 to work a submarine area of the Harbour seam (see Figure 1). It was closed in 1921 and the mine, which has a make of water of approximately 250 gallons per minute, was allowed to fill.No. 18 Colliery, situated almost a mile to the east, was opened in 1938 to work the Phalen seam in this area with the intention, later, of driving a cross-measure tunnel to mine the section of the Harbour seam lying between No. 17 Colliery and the Princess Colliery of the Nova Scotia Steel and Coal Company, Limited.In 1945 it became necessary to open this area in the Harbour seam and a cross-measure tunnel was driven from the existing workings of No. 18 Colliery in the Phalen seam, which underlies the Harbour seam at a depth of 500 feet.The tunnel was started in 1946 and completed in 1948. The cost of opening this section, which contained only 6 1/2 million tons of coal, made imperative the recovery of all the available coal and precluded the maintenance of the large barriers that had been left in No. 17 Colliery for impounding the water, especially as the maintenance of these barriers would have meant the loss of 885,000 tons of coal, or 12.3 per cent of the whole tonnage available. Therefore, a study was made to determine the best means to dewater the 250 million gallons of water lying in the old No. 17 Colliery."

Jan 1, 1952

By A. J. Chellew, Robert Condit

THE Company maintains a port agency at Antofagasta for dispatching copper and also for receiving from ocean vessels the vast variety of materials and supplies required at the plant. Copper shipments from the oxide plant refinery to Antofagasta amounted to 162,000 metric tons during 1951, while incoming freight totalled 175,000 metric tons. Electrolytic market copper in various shapes is currently loaded at the plant upon 20 or 30-ton cars of the meter-gage Antofagasta-Bolivia Railroad, to be transported a distance of 165 miles to the company's yard at Antofagasta. Here it is unloaded by cranes at the rate of about 175 tons per hr. Copper not scheduled for immediate shipment is stocked in tiers within the yard, but most of it is reloaded and sent to port works or a wharf serving lighters. Some of the vessels entering Antofagasta tie up at the port works, while others anchor inside the breakwater. In the latter case, all of the loading into the hatches is from 50-ton lighters towed to the vessel. When the vessel is at the dock, about half of the copper is loaded by port works cranes and the other half is loaded by ship's tackle from lighters. Fuel Oil Requirement Expands One of the innovations caused by the construction of the sulphide plant has been the necessity to provide facilities at Antofagasta for receiving and storing greater quantities of fuel oil than in recent years. From here it is loaded into tank cars for transportation to Chuquicamata. The older installation consisted of a 10-in. submarine pipe line, heating, and pumping facilities, a 67,500-bbl storage tank, and railroad loading rack, located at Antofagasta's northern limits. Two new tanks, of 80,000 and 30,000-bbl capacity respectively, have now been added and a second submarine pipe line will shortly be installed. Fuel oil requirements for the sulphide plant are estimated at 39,000 bbl per month, in addition to which 9000 bbl per month are required for the operation of the oxide plant. The company has a special lighter which is used by its diver for connecting the oil line with the oil tanker when disembarking oil, this lighter also being used for inspecting and overhauling buoys, as well as for recovery of bars of copper which are sometimes dropped into the bay when loading vessels during periods of rough weather. Transport of oil to Chuquicamata is by 76 tank cars of, 20-ton capacity and 20 of 30-ton capacity, all assigned to the company's fuel oil shipments excepting six for Diesel oil and one for gasoline. Incoming Freight Other freight received by the port agency has been averaging about 4800 metric tons per month of operating supplies for the oxide plant (renewals of equipment, spare parts, lubricating oils, and greases, etc.), some 1900 metric tons per month for the company stores, and about 6000 metric tons per month of materials and equipment for the construction of the sulphide plant. The greater part of these shipments (particularly the operating and construction supplies) originate from abroad, and must be handled through the Chilean Customs. Hence the company maintains a Customs storage warehouse (goods pending appraisal of Customs duties) in addition to its other storage facilities at Antofagasta. Not the least of the Port Agency's duties is to meet air and steamer passengers en route to Chuquicamata and to arrange for their trips up the hill. Landing in a strange country with a strange language, the first impressions of a new employee might otherwise be indeed confusing when facing Antofagasta's unique setting of brown barren hills.

Jan 1, 1952

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By R. A. Anderson, O. D. Sherby, J. E. Dorn

Solid solution alloying increases the plastic properties of aluminum at elevated temperatures by solid solution strengthening, by restraining recovery and recrystallization, and by a Cottrell effect. When binary aluminum alloys are strained and aged at 1940° to 300°K they develop a yield point. This is attributed to a migration of dislocations to solute atoms during aging. IN view of the ever expanding interest in applications of metals and alloys to high temperature service conditions, it becomes increasingly important to be cognizant of the effect of various metallurgical factors on the strength of alloys at elevated temperatures. One problem of wide interest, not only because of its engineering significance but also due to its fundamental scientific importance, is the elucidation of the effect of alloying elements on the plastic properties of homogeneous a solid solutions at elevated temperatures. It is indeed astonishing to note that in spite of its importance, and in spite of extensive random testing of alloys at elevated temperatures, no systematic investigation has been reported yet on the effect of alloying additions on the plastic properties of a solid solutions at elevated temperatures. This deficiency in our knowledge prompted the investigation described in this report. Rather extensive data are currently available on the effect of alloying elements on the plastic properties of a solid solutions at atmospheric and sub-atmospheric temperatures. Such data might be ex- trapolated to higher temperatures and reasonable guesses might be made regarding the influence of such factors as recovery and recrystallization in order to hazard a qualitative estimate of the effect of alloying elements on the plastic properties of a solid solutions at elevated temperatures. Such

Jan 1, 1952

FINANCE COMMITTEE OF THE BOARD OF DIRECTORS Erie V. Daveler, Chairman A B. Kinzel Gail F. Moulton INVESTMENTS ErIe V. Daveler, Chairman W L. Kleitz, '52 Henry Krumb, '53 Joseph E. Pogue, '51

Jan 1, 1952