Search Documents

By Douglass D. Donald

The New Jersey Zinc Co. successfully holed through a 2 ½ -mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8 x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial additional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine.

Jan 9, 1958

By W. C. Peters

From the time of its beginning in the mid-19th century, the American barite industry has had its major development in the eastern and central states. Geologic and economic factors serve to maintain Arkansas, Missouri, and the Southern Appalachian states in the lead position. In earlier days, the major markets for barite were in paint, chemical, and glass manufacturing, and the favored deposits were those which were close to eastern industrial areas; furthermore, the eastern deposits were cheaply mined and required little or no beneficiation. In the last few decades, the use of barite as a weighting medium for muds in rotary oil well drilling has caused a great expansion in the industry, but the marketing picture is still centered outside of the western states-now on the Gulf Coast area where high pressures are common in oil wells. Low cost imported barite, readily available on the East Coast and Gulf Coast, has always been a major marketing factor in the industry. The major barite producing state is Arkansas, with the industry centering about the Magnet Cove area. Missouri ranks second, with production mainly from residual deposits. Several Southestern states are actively producing from residual deposits.

Jan 9, 1958

By C. M. Marquardt

The minerals industry in general should bow in homage to the uranium milling industry. Those in the uranium milling industry have "spark- plugged" more progress in the application of instrumentation and control in the last 5 years than has been made in 50 years by the industry in general. Part of this real progress in the application of instrumentation and control has been born of necessity because milling processes are more complex. A lot of the impetus for instrumentation and control has come from the fact that the industry is new, the processes are new, and there are no hide-bound conventions to overcome. Part of it comes from the fact that much of processing is more chemical than metallurgical and the thinking of the process chemist has carried over into the plants. One need not elaborate on what instrumentation has done for the process chemical industries. Each new mill that is constructed, if of appreciable size, seems to employ more instrumentation than the previously completed plant. Plant A makes a break-through in the application of instrumentation to a particular part of the process and Plant B accepts this and goes one step farther, while Plant C, anticipating Plant B, makes two or three more steps before Plant B is entirely leveled out.

Jan 9, 1958

By John Peperakis

Coal mine bumps are normally associated with pillar mining under moderate or deep cover. Severe bumps at Sunnyside, however, have not been confined to pillar lines. Many have occurred in virgin development and in localities a long way from active pillar workings. As early as 1918 bumps in virgin territory were attributed to the faulted structure in the Sunnyside area.1 Sunnyside is an old property, mined for more than 60 years. Both man-made and natural conditions contribute greatly to bump occurrences, and loss of life and great destruction of workings have resulted from some unusual bumps in recent years.

Jan 9, 1958

By Charles T. Holland

This discussion is concerned with those comparatively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities.* Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.1

Jan 9, 1958

By Edward Thomas

THE late George S. Rice was active in the investigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and-to a lesser extent-Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,1 if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength2 in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable.

Jan 8, 1958

By A. Brown

RAPIDLY rising world demand for mineral pro- ducts has accelerated depletion of the more readily accessible ores, particularly those of premium grade. Operations must proceed at a faster rate to deeper horizons, where there are problems of ground control that restrict economic recovery of the mineral and introduce new hazards to mine personnel. For some of the new Canadian mining fields severe problems of ground stress are still in the future, but much of Canada's mineral output comes from well established mines that have reached considerable depths. It must also be anticipated that the depletion of premium grade ores will eventually necessitate mining low grade material at competitive cost, and unsolved problems of ground control can materially increase costs. Studies of ground stress phenomena in underground workings are therefore considered a present-day necessity, especially since these investigations must be a long-term effort owing to the highly complex nature of the problem and the difficulty of making full-scale observations.

Jan 8, 1958

By Frank D. Hoyt

BY far the most conspicuous of the Pennsylvania slate districts is that extending from the New Jersey line at the Delaware Water Gap westward almost to the Schuylkill River. This covers parts of three counties in east-central Pennsylvania: Northampton, Lehigh, and Berks. The most important development, both in geographic size and product importance, is in Lehigh and Northampton counties. The greater part of the region is underlain by only one formation-the Martinsburg, consisting of slates, clay slates, and sandy shales, all of the Ordovician period. The slate-bearing Martinsburg formation is underlain by Cambro-Ordovician limestones. Immediately overlying the Martinsburg formation is the Tuscarora quartzite of the Silurian period. The Martinsburg formation itself is divided into three distinct divisions, termed simply: the upper, the middle, and the lower members. Commercial slate has been extracted from all of these members, but the formation of greatest importance is the upper member, representing 2600 ft of the total formation thickness of nearly 11,000 ft. The upper member is commonly referred to as the "soft slate" and consists of three facies: 1) beds of blue-gray, very sandy, almost quartzitic slate, in many places, approximately a medium-coarse sand- stone with calcareous cement; 2) blue-gray sericitic slat-the dominant rock type of this member-with occasional chloritic beds; and 3) dark gray or virtually black, highly carbonaceous beds, referred to locally as "ribbons."

Jan 8, 1958

By John L. Schroder, Woods G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard.

Jan 8, 1958

THE term mountain bump describes the sudden rupture of one or more coal pillars under excessive stress. These bursts occur with varying degrees of violence and sometimes include adjacent strata, especially the bottom rock. Many failures do not develop enough violence to be dangerous and are regarded as an aid to coal production, but severe occurrences are accompanied by tons of flying coal, dense clouds of dust, and excessive gas emission. Such bursts sometimes throw heavy machinery several feet. Major factors to be considered in the problem are the nature of the strata above and below the seam and the depth of cover. Bumps are classified as to their nature, extent of damage, and point of occurrence, e. g., face bump, coal bump, high side bump, low side pavement bump, and district bump.

Jan 8, 1958

By James V. Thompson

ENGINEERS from industrialized countries are frequently called upon to examine mining operations in primitive areas and make recommendations regarding mechanization and modernization. They often set forth with self-confidence, knowing full well that all that is needed is their experience and several shiploads of mining machinery, and at times they mentally provide the answers before the problems have been clearly stated. In primitive areas it is absolutely essential that the examining engineer spend enough time at the site to acquire a thorough understanding of what is being done now and why it is done the way it is. The objective here is to state in simple terms some of the problems that may be encountered, in- as much as solutions, if they can be found at all, will differ with each experience.

Jan 8, 1958

ORE at the Jeffrey mine of Canadian John Mansville at Asbestos, Que., is hoisted by two 12 1/2 - ton capacity aluminum skips, counterbalanced. When the loaded skip reaches the surface it empties, via its sliding door, into a bin. Simultaneously, the skip tender, who operates at the 940 level, loads ore into the alternate skip from a 12 ½ -ton measuring pocket. This done, he sets the skips in motion. Problem: When moisture content of the asbestos ore is high, the ore, unknown to the skip tender, some- times sticks in the dumping skip, preventing complete discharge. Moreover, the sliding skip doors sometimes jam and stay open after the ore is discharged. If a skip in this condition is lowered, the result is either an overflow of ore, or the ore discharges through the open skip door, down the shaft. Spilled ore must then be mucked out of the spill pocket and hoisted in 2-ton cars. Cost is high, time is lost, and the shaft is sometimes damaged. Solution: A television apparatus was installed so that the skip tender might quickly spot improper door operation or hang-ups at the dumping station.

Jan 8, 1958

By John M. Warde, Eileen P. Burke

ORES of manganese and chrome have a high order of strategic importance, both metals are basic to the metallurgy and usefulness of steel, the fabric on which our economy rests. Looking beyond the current recession and short range picture of oversupply in these ores, this review attempts to answer the following questions regarding the longterm outlook for these key commodities: By 1970, what will be the probable demand here and abroad, what are future supply prospects, and what effect is the USSR likely to have on the world market? (See summary forecast on facing page.)

Jan 8, 1958

By John F. Myers

Since the art of comminution has lain practically dormant for many years, it is very interesting that R. T. Hukki approaches the subject with a new concept. One is reminded of the research carried on by A. W. Fahrenwald of Moscow, Idaho, a few years ago. Fahrenwald mounted a steel bowl on a vertical shaft. The balls and ore placed in the bowl were rotated at fast speeds, thus simulating the supercritical speeds used by Hukki. The rolling action of the balls against the smooth shell liner has pretty much the same effect. The action is horizontal in one case and vertical in the other. Both researchers report good grinding activity.

Jan 8, 1958

SUDBURY ore processed by International Nickel Co. of Canada Ltd. was recovered for many years as two mill concentrates, one primarily of copper, and the other mixed pentlandite-pyrrhotite, But, Since iron content of the nickeliferous pyrrhotite concentrate was ten times its nickel value, capacity of smelting was limited by the need for slagging the excess iron. A process for recovering the iron con- tent was developed after some years of research and a $20-million plant was constructed to employ the new method. Built near Copper Cliff, Ont., the plant started operation early in 1956, scheduled for separate treatment of 365,000 tons of pyrrhotite each year. It is only the first unit of an installation which will have a capacity of more than 1 million tons per year of pyrrhotite. By early 1958, production totaled more than 200,000 long tons of 68 pct Fe pellets containing 0.003 pct P, 1.5 pct SiO2, 0.01 pct S, and 0.15 pct Ni.

Jan 8, 1958

By D. H. Yardley

GEOCHEMICAL investigation of trace elements in surface materials was begun near Ely, Minn., in 1953 along the basal contact of Duluth gabbro with Giants Range granite (Fig. 1). This article presents data on the distribution of copper and nickel in till and in stream sediments in the area and proposes an explanation for the types of distribution found. The Duluth gabbro, one of the world's largest basic intrusives, intrudes rocks which range in age from Keewatin to middle Keweenawan. Within the test area the gabbro is in contact with granite except for short sections where it is in contact with remnants of iron formation. Sulfide mineralization occurs within the gabbro, near and parallel to the basal contact for a distance of several miles. Schwartz and Davidson1 have described the geologic setting of the mineralization.

Jan 7, 1958

As a service to its readers, MINING ENGINEERING is publishing the mineral industry portion of the 1957 list of Accredited Undergraduate Engineering Curricula in the United States. This list, revised annually, is issued by the Education Committee of the Engineers Council for Professional Development, and covers all phases of engineering education. The AIME is actively represented on ECPD, which was jointly organized by the Founder Societies and various other groups interested in the professional recognition of engineers. ECPD is merely authorized by its constituent organizations to publish a list of accredited engineering curricula for use as desired by those agencies which require such a list. It has no authority to impose any restrictions or standardizations on schools. (Date following school refers to year of initial accrediting.)

Jan 7, 1958

By R. J. Woody

DESIGN of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 7, 1958

By S. E. Craig

UPON entering the Uranium Field it was a pleasant surprise to find almost absent two factors that have always been a problem to the lead-zinc miner: 1) milling cost per ton, and 2) transportation cost to the milling site. Another interesting condition was the fixed price for the product. Under such conditions it seems rather simple to calculate the economics of a mining venture when grade and tonnage of a uranium ore deposit is known. That is assuming, of course, there is a market for the ore. It has been quite generally assumed by operators that a guaranteed price carried with it a guaranteed market, a subject about which there has been a great deal of discussion in the past several months. The fixed price for uranium in crude ore, calculated to U3O8, varies only slightly in value per pound from rather low grade ore to rather high grade ore. It is by taking advantage of this slight variation in price per pound in certain ranges that miners and shippers may increase substantially the monthly returns from ore shipments.

Jan 7, 1958

By Rudolph G. Wuerker

WITH the growing complexity of ore dressing processes and the diversity of equipment, efficiency control has become increasingly important in beneficiation. In the case of iron ore dressing, there have been sporadic attempts1-3 to establish the optimum separation for various ores so that grade and recovery would be readily predictable. But no rigorous statistical analysis and graphical presentation of such tests could be found in the literature of this country. Tests Made with Iron Ores Expanding upon existing methods of plant supervision and efficiency control, an investigation was started in the ore dressing laboratory at the University of Illinois on the applicability of distribution analysis to iron ores. A sample of crude ore was obtained from the Ohio mine of Cleveland-Cliffs Iron Co. at Ishpeming, Mich., consisting mostly of alternating bands of hematite and siliceous gangue, both about ¼ in. wide. The ore was heavily coated with limonite, which often filled the cracks.

Jan 7, 1958