Search Documents

By C. F. Clausen

"Cement" means binding agent or glue. It is derived from the Latin word "Caementum," the name of a limestone, chips of which were used in mortar more than 2,000 years ago in Italy. During the middle ages "cement" or "cement" generally denoted mortar. Today it means any binding material. The Thomas Register lists nearly 200 classifications for "cement" including automobile cement, household cement, rubber cement, etc. The material most commonly associated with this word, however, is portland cement which, when mixed with water and allowed to hydrate, is a ceramic binding material used to cement aggregates (crushed stone, gravel and sand) together in "concrete," the most universally used building material of today. It is estimated that more tons of concrete are used annually than all other building materials put together including steel, lumber, gypsum, bricks, tiles, aluminum and glass. Its use in foundations, building construction, sanitary work, dams, railroads, and highways, makes it difficult to conceive of modem civilization without concrete. A survey made in October 1955 showed the following uses of portland cement: [Percent Highways20 Nonresidential buildings20 Residential buildings15 Military construction10 Sewer and water works8 Public utilities10 Other (conservation, farm, and maintenance and repair)17 100] As of today, the percentage for highways is probably even higher. Ceramic binding materials have unquestionably been used in construction work for thousands of years. The mortar between the blocks of the great pyramids was calcined gypsum (plaster of paris). The use of calcined and slaked limestone goes back earlier than the Roman Empire. Gypsum, however, is relatively soft, and common lime mortar is not "hydraulic," i.e., it does not harden under water. The Greeks and Romans discovered later that an addition of a finely divided active siliceous material (Santorin earth or Pozzolana) would react with slaked lime to form a stronger, and hydraulic, cement. The Appian Way in Italy, Colosseum, and the great Aqueducts built by the Romans were made with this type cement, and some of these structures are still in existence today. However, not until 1756 did some serious research result in the development of better cements. In that year the English engineer, John Smeaton produced a stronger cement by burning a limestone containing considerable proportions of clayey impurities. Other investigations and improvements were made by Bryan Higgins, Bergmann, Joseph Parker, L. J. Vicat, J. F. John, James Frost, and I. C. Johnson.2 Traditionally, but perhaps unfairly to others, the invention of the prototype of today's portland cement is credited to the English mason Joseph Aspdin who in 1824 obtained a patent and gave the product its name, because in color the mortar produced from it resembled a natural building stone obtained from the British Isle of Portland. The contributions of Johnson and Aspdin were primarily the important step of preparing a synthetic mixture of lime and clay without depending on raw materials found in nature which might contain such elements in desirable proportions. However, even these early

Jan 1, 1960

By J. J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely inadequate in certain other areas, but there are important sections where this system is clearly applicable. Horizon mining is practiced in the Lead Belt, and stopes may vary from 10 ft to well over 100 ft high. Fig. 1 is a plan view of 6100 stope, the area to be discussed. For these mines this is a small stope, only 10 to 12 ft high. Before any plans were drawn up for pillar recovery, three independent estimates of the pillar grades were made by the mine superintendent, the mine captain, and the mine geologist. After these results were averaged, pillars indicated to be of economic grade were marked for removal as shown. At this stage several alternatives were considered: 1) retreat with caving, 2) concrete replacement pillars, and 3) systematic bolting and retreat. A retreating system with caving was not chosen because the roof was known to be too bad even to permit loading a blasted pillar before caving would begin. Concrete replacement pillars would have been too costly and would have required a large crew, bulky materials, and unwieldy equipment. Systematic bolting was chosen as being most acceptable for the following reasons: 1) Limited area and spans were involved. 2) Only minor modifications to the jumbo would be required for bolting. 3) Only a two-man bolting crew would be needed. 4) Only compact bolting materials would be required. 5) The bolting plan could be modified to allow

Jan 1, 1960

By W. L. McMorris

The Convertol process was first described in Germany by Muschenborn' in 1952. In the U. S. Fraser' reported this new process in 1953, and Brisse and McMorris" presented the results of a Convertol pilot plant at the Alpheus preparation plant in Gary, W. Va., illustrating the mechanics of the process by a series of sketches. The purpose of the present investigation was threefold: 1) to determine the relative effectiveness of various oils and hydrocarbons for recovering coal by the Convertol process, 2) to ascertain the behavior of coal pulps in this process under various operational conditions, and 3) to compare Convertol with flotation in the recovery of fine coals. APPARATUS, PROCEDURE, AND COAL SAMPLES In laboratory work with the Convertol process a Waring Blender equipped with a speed-regulating rheostat was used for wetting, conditioning, inversion, and retention of the coal pulp. A 5-in. International centrifuge was adapted to dewater the agglomerated clean coal product by installation of a 100-mesh screen inside the regular bronze basket of the centrifuge. Except where otherwise stated, the Convertol testing was performed by the following steps: 1) A 450 to 500-cc coal slurry, containing 24 pct by weight of solids, was agitated in the blender for 10 min at 100 rpm to insure complete wetting and mixing. 2) Eight percent by weight of oil was added to the coal slurry in the blender and agitated for 1 min at 11,000 rpm to result in the phase inversion or agglomeration of oil-coated coal particles. 3) The agglomerated coal slurry was poured onto a 100-mesh sieve and wet-screened for about 2 min to remove most of the ash and some of the water. 4) The material remaining on the screen was transferred into the centrifuge for final dewatering. 5) A portion of the clean coal was immediately weighed out for moisture determination, while the

Jan 1, 1960

By R. D. Nelson, D. H. Polonis

ThE eutectoid decomposition of 6 phase in the Cu-Sn system (32.53 wt pct Sn) has been studied by several investigators.1-6 On the basis of X-ray work, Iball and 0wen1 reported complete decomposition of 6 in powder specimens after 7 days at 300°C. Wang and Hansen followed the micro-structural changes during heat treatment of lump specimens and estimated 5 pct decomposition after 63 days at 300°C. Wang and Hansen suggested that the discrepancy between the decomposition rates of powder and lump specimens might be due to the excess surface free energy of powders. The present work involved 6 decomposition in copper-tin alloy powders containing 32.6 wt pct Sn. Alloy lump specimens exhibited entirely 6 phase after fairly slow cooling (air cooling) from above 350°C and were so brittle that they could be easily crushed to-200 mesh in a percussion mortar. X-ray diffraction study of the as-crushed powders (-200 mesh) revealed 100 pct 6 phase with very slight line broadening effects due to strain introduced by crushing. Only 6 phase was detected by X-ray diffraction in powders which were heat treated 4 hr at 450°C and air cooled to room tem-

Jan 1, 1960

By C. G. Dunn, E. F. Koch, K. T. Aust

Strain-induced grain boundary migration was studied in a series of silicon-iron (3% pct Si) bicrystals of controlled orientations. Each bicrystal was given a 7 pct cold-rolling strain rind annealed at 1100°C. The direction of boundary migration was found to depend on orientation; results for several orientations related by a common [110] axis are given. Analysis of the micrographic and X-ray data is made in terms of the residual strain-energy densities within the crystals (energy per unit volurne) and a driving force on the boundary due to an energy density difference across the boundary. Relative strain energies were obtained for the various orientations investigated. A CHROME-acetic acid electroetching method for revealing dislocation sites in silicon iron was previously applied to clarify the structural features and the energetics involved in strain-induced grain boundary migration.',' The present paper is a continuation of this study, but is primarily concerned with the influence of crystal orientation. Sperry, as reported by Beck,3 attempted to determine the factors that influence the preferred growth of one grain over another in aluminum due to strain-induced boundary migration. He found that the particular grain of a pair which work hardened more was invaded, although exceptions to this correlation were noted. The index of work hardening was determined from microhardness measurements of each grain before and after cold-rolling. In the present study, orientation itself was taken as a useful variable for studying the behavior of individual grains in a bicrystal and the direction of boundary migration, since the extent of work hardening is orientation dePendent." The effect of strain on boundary migration is evident from a consideration of driving forces. Thus, in the absence of inclusions, the driving force (per unit area of boundary) for growth of grain A into grain B when a bicrystal is strained and annealed may be expressed as follows:2

Jan 1, 1960

The stratigraphy of the Western Coalfield is briefly reviewed and the important units of the Lithgow Coal Measures, particularly the coal seams, are defined. The possibility of coal measures of Tomago age ocurring near the edges of the Sydney Basin is discussed onpresent evidence.Using data obtained from unpublished drilling records, detailed structural, isopachous and lithofaeies maps have been drawn. These show that the structure of the coal basin has been influenced by the underlying basement in many ways.The prominent jointing in the overlying Triassic sandstones is discussed in relation to jointing in the coal measure sediments.It is concluded that in addition to the general knowledge obtained with respect to the coal basin, useful information regarding coal quality and quantity can be gained by the study of broader sedimentary and structural features.INTRODUCTIONThe term "Western Coalfield" covers approximately the area from Katoomba to Rylstone, together with the smaller, separate Ulan area (Fig. 1). The area studied is part of the great sedimentary Sydney basin named by Osborne (1948). The first discovery of coal in Sitlt in the area was made in 1824 by Andrew Brown, although George Bass noted the presence of coal float in the Grose River in 1797. Production is recorded from the Western Coalfield in 1838 but mining was intermittent until 1868 when mines in the Lithgowvalley (producing coal from the Lithgow Seam) came into production. In 1882 the Katoomba Seam was first worked at Katoomba.The work of J. E. Carne (1903, 1908) defined the limits of the Coal Measure sediments and also contributed a great amount of valuable detailed information about the region.

Jan 1, 1960

By J. W. Thomson, H. J. Lloyd, R. J. Taylor

"THE HOLLINGER MINE has been producing gold and by-product silver almost continuously for forty-eight years. The value of current production is $10,000,000 annually from one million tons of ore. Its management •has, particularly over the past decade, increasingly . concerned itself with the problem of profitable operation in a time of steadily rising costs and a fixed price of gold. At one period in the life of the mine, before World War II, production resulted in yearly profit margins that were stable and relatively thick. In winning gold from a series of inconsistent vertical ore lenses, operating management was much better protected than it is today against a general rise in cost or dip in grade of ore. The tissue-like thinness of present-day margins demand more careful handling. A sharp rise in costs, if protracted, could easily rip the tissue to shreds and close down the business. The counter-measure of raising grade and gutting the mine would bring on the end perhaps more rapidly, without having contributed much to the recovery of our national re-sources, nor to community welfare. The alternative is to keep costs under control."

Jan 1, 1960

By Harrison A. Schmitt

During .the past five decades or so we have passed from a time when it was difficult to point to a mine or an ore body and verify that it had been discovered by geological methods, through the. Twenties when the common saying was, "Who ever heard of a mine found by a geologist?", to recent decades when hundreds of mines and ore bodies are acknowledged geological discoveries and the above query can be ignored. Recently, however, the application of mining geology appears to have been downgraded, or so it seems to me. Basic geology in mining has been cheapened and glossed over in favor of geophysics and outcrop sampling, even though the latter is merely one technique of mining geology and, to some extent anyhow, has been used for a. long time. (Locke, 3, pp 81-87). Geophysics by itself and in conjunction with geology has had success in certain geological provinces, but limited attainment in mountainous terrane except in those few cases where strongly magnetic minerals are associated with ore. Nevertheless, in the Cordillera .many experimental techniques are offered as proved ones. This is not an intent to try to depreciate honest geo- physics. Continued experimentation and use of it is approved by all, but at the same time it is foolhardy to throw mining geology overboard, Generally both approaches should be considered and usually, at first anyhow, geology is the most direct one.

Jan 1, 1960

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

By N. R. Paterson, D. G. MacKay

"The geology of the Mattagami mining camp, while of particular economic significance, is unfortunately obscured by a very thick mantle of overburden. For this reason geo-physical methods have been relied upon heavily in exploring the area. Geophysical data over five important sulphide discoveries show how targets are selected for drilling and how effective geophysics has been in assisting subsequent development programs."

Jan 1, 1960

By G. T. Engel, W. G. Gruzensky

Jan 1, 1960

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By K. A. Svanstrom, W. R. Opie

Problems associated with deposition of titanium infused chloride baths using TiCl4 as a feed material are reviewed. A potentially workable cell design using Alumdum diaphragms is discussed. Problems inherent to diaphragm-type cells are emphasized and experiments described which led to the development of a cell without a diaphragm. INVESTIGATORS assigned the problem of developing a commercial electrolytic process for making titanium metal have found that they are faced with the difficulty of overtaking rapidly improving magnesium and -sodium reduction processes. The ultimate goal must be a simple process that can be conducted with low-cost raw materials in equipment that is inexpensive to build and operate. This paper deals with some work of a preliminary nature conducted by personnel of the Research Laboratories, National Lead Co., Titanium Division. Many others have reported on the general subject of depositing titanium from fused salt electrolytes. A partial bibliography is attached. PRIMARY CONCEPTS Anyone attempting to deposit titanium metal from fused chloride electrolytes using TiC14 as a source material is faced with at least the following problems: 1) Getting the titanium into solution in the bath. 2) Controlling oxidation and reduction reactions associated with multiple valency of titanium, which result in low electrical efficiency. a) Prevention of dichloride oxidizing to trichloride and trichloride to tetrachloride at the anode. b) Prevention of trichloride from being reduced only to dichloride at the cathode. 3) Prevention of metal formation away from the cathode thru disproportionation of titanium dichloride to satisfy the equilibrium. 3 TiCl2 == 2 TiCl3 Ti [I] 4) Protection of reduced chlorides in the bath from reaction with oxygen from the bath container or air. 5) Removing from the bath the deposited metal formed without allowing it to become contaminated with oxygen or nitrogen. 6) Selecting cell materials of construction which will not contaminate the metal product or cause cell inefficiencies. EARLY EXPERIMENTS The initial attempts made to electrodeposit titanium from fused chloride baths using TiCl4 as a source material indicated that TiCl4 was essentially insoluble in molten chlorides of alkali and alkaline earth metals. If, however, the TiCl4 was introduced close to a nickel cathode some metal could be formed and appreciable quantities of reduced chlorides would be present. These reduced chlorides reacted with any oxygen present in the atmosphere above the bath and would also diffuse quickly to the anode (graphite) where they would react with chlorine and be evolved as TiCl4. The net electrolytic efficiency of such a cell is essentially nil. The TiCl4 evolves from the anode at almost the same rate that it is introduced in the vicinity of the cathode although a small amount of titanium metal can be formed on the walls of the cathodic pipe. It becomes apparent from the operation of such a cell that: metal can be deposited on the cathode, although of small particle size and a nonadherent nature, and when reduced chlorides are present in the electrolyte, TiCl4 can be absorbed, probably by the following reactions: TiCl4 + TiC12 - 2 TiCl3 [21 2 TiCl3 + 2 faradays - 2 TiC12 + C12 [31 DIAPHRAGM CELLS These facts encouraged the development of cells containing diaphragms to prevent migration of reduced chlorides from the cathode area to the anode. Small-scale cells for process development are described by Alpert, Schultz, and Sullivan.20 A larger brick-lined cell incorporating internal heating by passing ac through the bath is shown in

Jan 1, 1960

By C. Elbaum

If a thin layer of liquid gallium is spread on a surface of solid aluminum, the gallium penetrates high-angle grain boundaries at a very rapid rate and separation along these boundaries follows. An experiment was carried out to investigate this phenomenon. A well-annealed specimen of aluminum 99.994 pct pure, consisting of several large grains was used, Fig. 1. The dimensions of the sample were 25 mm wide by 2.5 mm thick and all the grain boundaries extended through the entire thickness of the plate. This sample was prepared by strain-annealing and, as can be seen in Fig. 1, contained one long, straight boundary. An examination of the crystal orientations showed this boundary to be a coherent twin boundary. The angular misorientations between the grains forming the other boundaries were all in excess of 20 deg. A thin layer of liquid gallium was spread on one side of the specimen at about 30°C (the melting point of gallium is 29.7"C). After the application of the liquid the temperature was lowered to about 27°C. The gallium remained liquid at this temperature and it can be seen from the A1-Ga phase diagram1 that the liquid was probably saturated with aluminum.

Jan 1, 1960

By R. V. Lundquist

A method was developed by the Federal Bureau of Mines for evaluating viscosity data from slurries obtained in leaching sinters from the lime soda sinter process for extracting alumina from aluminous silicates. The logarithm of the viscosity was observed to be a linear function with time. The slope of the plotted line provides a means for evaluating viscosity behavior in a lime soda sinter blurry and also a means for comparing gelation characteristics directly with other variables in the lime soda sinter process. This report presents one aspect of a continuing study by the Bureau of Mines on methods for treating siliceous aluminum ores. It is one of the many programs of the Bureau concerned with conservation, development, and use of our domestic minerals resources. Previous investigations of lime soda processes, both by the Bureau4-7/ and industrial concerns, have demonstrated that sintered materials containing CaO, Na2O, A1203, and S102 in various combinations exhibit a tendency to gel or set when mixed with water or other extraction solutions. Gelling prevents satisfactory recovery of alumina and in extreme cases prevents operation of an extraction plant.

Jan 1, 1960

By J. A. Berge, R. S. Mateer, R. G. Aspden

IN a study of the cold-rolling characteristics of iron-base alloys with 3 to 12 pct Al, the influence of aluminum content on the cold-rolling textures was evaluated. This work was undertaken to determine if binary iron-aluminum alloys possessed cold-rolling textures similar to other body-centered-cubic alloys and to contribute additional information on the effect of solute concentration on the cold- rolling textures. Gradual changes in cold-rolling textures with an increase in solute content have been observed in copper1 and in titanium.2 Iron-base alloys containing 3.0, '6.0, and 12.0 pct aluminum were vacuum-induction-melted in a magnesia crucible and permanent-mold cast. The materials used were high-purity electrolytic iron and 99.99 pct grade aluminum. Each ingot was 1 in. square in cross section by 12 in. in height. The bottom half of each ingot was soaked for 1 hr at 1000°C and rolled at 1000°C to a thickness of 0.055 in. with the long axis of the ingot parallel to the rolling direction. The strip was reheated between passes to maintain a rolling temperature of 1000°C.

Jan 1, 1960

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Strain-induced porosity has been found to occur in titanium and other materials at tensile strains greater than the uniform elongation of the material. Porosity in titanium increases with increasing strain and temperature, being most severe at 300° to 800°F. Strain-induced porosity is believed to be a normal part of the mechanism of deformation in ductile materials. DURING the past few years there have been numerous references to the occurrence of voids in laboratory test specimens of metals subjected to strain.l-7 These voids have been referred to as intercrystalline cracking, strain-induced porosity, intergranular cav-itation, voids, and porosity. They appear to occur at grain boundaries or interfaces, and are generally associated with large amounts of strain and have been found mostly in creep specimens and to a lesser extent in tensile specimens. Because the phenomenon does not occur unless the material has been strained,

Jan 1, 1960

By Alla D. Mah

The work described in this report is part of a Bureau of Mines research program for obtaining heats of formation of inorganic oxides, carbides, and nitrides by combustion calorimetry. The heats of combustion of molybdenum subnitride (Mo2N) and chromium subnitride (Cr2N) were measured. The data were combined with previous determinations of the heats of formation of molybdenum trioxide and chromium sesquioxide to obtain the heats of formation of the two subnitrides from the elements at 298.15° K. The corresponding free energies of formation were estimated. The heat data were compared with those of nine previously studied nitrides.

Jan 1, 1960

By S. Yukawa, M. J. Sinott

The low solubility of bismuth in copper and its segregation at copper grain boundaries with resulting embrittlement is well known.1-3 The heterogeneous diffusion of liquid bismuth into polycrystalline copper has also been studied.4 This work presents some further observations on these phenomena using high-resolution auto radiography to detect the presence of bismuth in copper polycrystalline and bicrystal specimens. The auto radiographs were made by the stripping film technique which produces an autoradiograph that is intact with specimen surface and can be examined simultaneously with the under-lying microstructure. The details of the technique have been described previously.3 In one series of experiments, high-purity copper was alloyed with 0.02 to 0.03 wt pct radioactive bismuth obtained from the Oak Ridge National Laboratory. Melting and casting was done under a

Jan 1, 1960

By Joseph L. Gillson

Bentonite, designating a distinct type of clay, is a young name in mineral nomenclature in the light of the age-old names of most other useful nonmetallics. The earliest references in literature are to "soap clay" (1873) "taylorite" (1888) and finally "bentonite" in 1897, from its occurrence in the Fort Benton series of rocks near Rock Creek, Albany County, Wyoming. Bentonite is a rock term and consists largely of montmorillonite clay. The latter name was proposed in 1847 for a plastic clay found at Montmorillon, France. A clay of apparently identical properties was described by Cronstedt of Sweden in 1788 and a number of other similar clays found in France were given other names in publications from 1853 to 1856. The mineral name montmorillonite was recognized by Dana in 1892. The recognition of "clay mineral" distinctions which led to the present-day classifications of clays by their chief mineral content, dawned in the early part of the twentieth century. Grim6 has aptly said: About 1924, Ross10 and some colleagues of the U. S. Geological Survey began a study of the mineral composition of clays that led to a series of monumental papers on the subject. By the early 1930's what has come to be known as the clay-mineral concept became firmly established in the minds of a great many people actively studying clay materials. The clay mineral concept designates the major clays as kaolins, montmorillonites and illites and by this concept bentonites are now defined as "fine-grained clays containing not less than 85 pct montmorillonite" and a wide variety of clays found all over the world are included in that classification. They could all properly be called "montmorillonite clays" but the common commercial name is bentonite. For a period of over forty years from the time of the earlier discoveries, bentonite was thought to be only the sodium type highswelling clay produced principally in Wyoming. By the clay mineral concept, non-swelling montmorillonite clays also became known as bentonite. In the trade there are two broad divisions-sodium bentonite, often called Wyoming or "western," which expands in water and carries sodium as its predominant exchangeable ion, and calcium bentonite often called "southern," which has negligible swelling and carries calcium as its principal exchangeable ion. There are many intermediate gradations. Properties The mineralogy and chemistry of the clays are so complex that the subject cannot be summarized briefly. The reader is referred to Chapter 12 of this volume in which the subject is treated at some length. Grim6 gave the formula for montmorillonite as (OH)4Si8AL4020.nH2O. He wrote: Montmorillonite is composed of units made up of two silica tetrahedral sheets with a central alumina octahedral sheet. . . . Exchangeable rations occur between the silicate layers. . . . The words "tetrahedral" and "octahedral" refer to the coordination number of the cations in the unit cell in the crystallographic lattice. Carroll5a stated: That the montmorillonite structure is the same as that of mica, but the layers are not held together by K+ ions; and water and other polar molecules, such as organic molecules, can enter between the unit layers and cause expansion. Ex-

Jan 1, 1960