Search Documents

The Rosebery and Hercules mines, situated in the Rosebery-Williamsford district in western Tasmania, have a history of production dating back to 1896-7, although full scale production did not commence until 1936, following the development of a satisfactory process of selective flotation (Hall, Cottle, Rosenhain and McGhie, 1953). The mineral composition of the Rosebery zinc-lead ores was first described in detail by Stillwell (1934). The Hercules ore is generally similar, but as yet no descriptions of it have beenpublished.Since Dr. Stillwell's paper appeared, the management of the Rosebery and Hercules mines has from time to time submitted a number of interesting mineral specimens to C.S.I.R.O. Mineragraphie Investigations. Examination of these specimens brought to light eight minerals, some relatively uncommon, not previously recognized in these ores.They are cassiterite, molybdenite, stannite, electrum, meneghinite, boulangerite, pyrargyrite and pyrrhotite. Some of the specimens are also rich in tetrahedrite and gold. In addition each of the other ore minerals described by Stillwell, viz. pyrite, sphalerite, galena, bournonite, chaleopyrite and arsenopyrite, was detected in one or more of the specimens examined during the present study. The principal gangue minerals were found to be quartz, manganiferous carbonate, sericite and barite, agreeing closely with the observations of Stillwell.The present study was based on the examination of the following eight specimens.

Jan 1, 1960

By W. H. Ode

Because trade increased among various nations after World War II, the Coal Committee of the Economic Commission for Europe established a Classification Working Party in 1949 to develop an International system for classifying coal. Although national classification systems existed, they had been developed in accordance with characteristics of domestic coals without reference to coals of other countries. Terms for describing similar or identical coals differed in each nation. This caused confusion in evaluating coals shipped in international trade and also hampered exchange of technical information on problems of coal utilization. Experts4/ participating in the classification project early in their work agreed that two systems should be formulated, one for the higher rank coals or so-called "hard" coals in European terminology and the other one for the lower rank coals, the latter designated mainly as brown coals and lignites in the various countries. Rank refers to the degree of metamorphism (progressive alteration) in the natural coalification series from lignite and brown coal to anthracite. The system for classification of hard coals was published late in 1956 as a document of the United Nations.5/ Results of a study for applying this system to American coals were published in 1958.6/

Jan 1, 1960

By B. S. Crocker

Pebble grinding was used at Lake Shore Mines in 1949. A full description of experimental evidence and test plant results was published in 1952 1 and further operating details in 1954 2.' In more recent years the term autogenous grinding has been coined and is now frequently seen in the technical literature. Autogenous crushing and/or grinding covers any grinding mill in which the larger pieces of ore are made to grind the fine pieces; the crushing and grinding may be either dry or wet. This discussion deals only with wet autogenous grinding, and only in the fine grinding part of the circuit, i.e., from 6 mesh to 92 pct —325 mesh. The term pebble milling could apply to fine autogenous grinding in which the pebbles are made from the ore itself, or it could also refer to grinding with pebbles, such as flint pebbles, from a source outside the mine. The first mill to use screened ore to grind the ore (1949) was Lake Shore Mines, Kirkland Lake, Ont. Pebbles were screened from the jaw crusher discharge and used in 5x16-ft tube mills which had been converted to 6 ft 8 in. by 16-ft grate discharge pebble mills. The same general practice was adopted the following year by the Wright-Har-greaves Mine in Kirkland Lake. Shortly after that the Neptune Mines in Nicaragua started correspondence with the writer concerning the possibility of using screened ore for grinding in their plant. They first ran some plant-scale tests which confirmed the Lake Shore findings, with the ultimate result that their plant was successfully converted in 1956 to an autogenous grinding plant. In 1957-1958 the writer was successful in converting the grinding plant of Renabie Mines in northern Ontario to autogenous grinding. In all these plants the existing grinding equipment was converted, usually by expanding the diameter of the shell to make the change from steel grinding to ore pebble grinding mills. In all the above plants primary grinding was done in either small rod mills or ball mills. These mills first reduced the pebble mill feed to about 6 mesh. The final grinding in the pebble mills varied from 75 pct —200 mesh to 92 pct —325 mesh. At Lake Shore three stages of pebble milling were used, with a different size pebble in each stage. In other parts of the world interest was being shown in this form of grinding, and in March 1952 the writer had some correspondence with the mill staff at Outokumpu in Finland, with regard to the pebble system used at Lake Shore. At Stockholm in 1957 the account of the crushing and grinding system at Outokumpu was presented in a paper by H. Tanner and T. Heikkinen.V his is the only ore grinding plant that does not use grate discharges on its pebble mills; trunnion discharges equipped with heavy reverse spirals retain the pebble load. The first new mill designed to use screened ore as a grinding medium was the Bicroft mill at Bancroft, Ont., which began operation in the fall of 1956. In 1957 this plant was followed by similar installations at Faraday Mines, also in the Bancroft area, and the North Rankin Nickel Mines in the North West Territories. In 1958 the Dyno Mill at Bancroft was converted, using the same type of grinding. Since all these plants, designed by Kilborn Engineering (1954) Ltd., were originally planned as pebble grinding mills, they were able to take full advantage of the latest design and technique. They are neat in appearance and very efficient and easy to operate. Effect of Ore Hardness: It is often commented that this type of autogenous grinding applies only to hard siliceous ores. Experience has shown that this is not so. In the past ten years the author has had an opportunity to test more than a dozen ores, several of which were quite soft. One of these was shale. The softer ores actually make better looking pebbles than the hard ores. These soft ores produced no particles in the intermediate size range which could not be ground by the largest pebbles in the mill charge. Slabby ores, such as shales, make a suitable pebble for the —6 mesh grinding. It is not generally recognized that for fine grinding a spherical medium is not essential or more efficient. Another frequent objection to pebble grinding is the belief held by some operators that there is too much variation in the hardness of their particular ore to make it acceptable as a source of pebble media. Experience has also shown that this is not a serious problem at all. The variation in pebble load due to changes in the ore hardness is nothing like as great as most people would expect, and the method used for feeding the ore and controlling the the load in the mills is more than sufficient to take care of daily variations in ore hardness. This point

Jan 1, 1960

By A. G. Guy

Zinc vapor from a reservoir of liquid zinc maintained at lower temperatures was diffused into sets of copper-zinc alloys at 759° and 870° C and into sets of silver-zinc alloys at 650° and 700° C. Each set of ,four copper-zinc alloys consisted of pure copper and 90/10, 80/20, and 70/30 brass. Similarly the set of silver-base alloys consisted of specimens containing 0, 7, 15, and 20 pct Zn. Natural markers at the initial surfaces of the specimens ware "trapped" under a thin electroplate and their depth of burying was measured after diffusion. The ratio of diffusivities of the two components determined from these data and the chemical diffusion coefficient calculated by the Matano method agreed with previously reported results. The line of markers was irregular and was often discontinuous when a grain boundary was crossed. TECHNIQUES involving the vapor phase have been widely employed in studying diffusion phenomena in metals. Many investigators have evaporated the more volatile component from an alloy, but it is generally believed that the porosity created under these conditions interferes with adequate interpretation of the experimental results. The extensive work of Gertsriken6 has been criticized on this score. Accary1 found that the diffusion coefficient for de-zincification of brass is larger by a factor of five than that for zincification, although he attributed the difference to a higher vacancy concentration under conditions of dezincification. Balluffi and siegle2 thoroughly investigated the technique of adding a more volatile component to a less volatile base metal as a means for studying diffusion. They verified that no porosity forms in a brass under these conditions and that the diffusivities of the two components can be determined from observations of the motion of markers originally placed on the surface of the specimen. The mathematical analysis that they developed for treating the experimental data was modified in a later note, but essentially it involved using the graphical Boltzmann-Matano method that is customarily applied to solid-solid diffusion couples. The experimental method used in the present research was similar to that employed by Balluffi and Siegle except for two modifications. Balluffi and Siegle used alloy chips as the source of metal vapor. This procedure has the disadvantage that the concentration of solute at the surface of the specimen changes during the diffusion experiment as the alloy content of the chips is gradually decreased. This disadvantage was overcome by employing liquid zinc as the source of zinc vapor in a manner similar to that described by Herasymenko.9 There was then no limitation on the amount of solute usefully available, and several relatively large specimens could be diffused in a given experiment. The second modification was the use of natural markers on the surface of the specimen rather than larger, artificial markers, such as the alumina powder employed by Balluffi and Siegle. It was expected that the fine, natural markers would permit more precise measurement of the buried interface as in the case of ordinary sandwich specimens.10 EXPERIMENTAL The experiments were designed so that zinc from the vapor phase would maintain a constant zinc content at the surface of pure copper (or silver) and

Jan 1, 1960

By J. M. Ohm, C. M. Bunker

Two special tools for recovering gamma-ray probes and logging cable from drillholes have been designed by Ohm and Bunker and constructed by Ohm. Though intended specifically for U. S. Geological Survey equipment, they may be used with other equipment of the same general type. Fishing Tool for Probes: A fishing tool of the overshot type (Fig. 1) was designed to retrieve logging probes (sondes) that become disconnected from the logging cable and are trapped in the drillhole. When the tool slides over the top of the gamma-ray probe, studs on the bottom engage the shoulder near the top of the probe (Fig. 2), which is then pulled to surface. The barrel can be constructed from brass or steel tubing. Wall thickness is not a critical dimension, but the tool should be heavy enough to sink through mud or water in the drillhole. The internal length of the tool must be enough to prevent interference with the upper end of the probe head as the tool slides over it. The design of the probe head used by the USGS required a minimum free space of 2 1/2 in. inside the fishing tool, which was made 7 1/2 in. long to increase the weight. The lower end, which engages the shoulder of the upper end of the probe, contains three studs placed at 120" around the circumference of the tool and held in the engaging position by the tension of a spring wire. The studs can be made of any metal, such as steel, having high tensile strength. As the tool slides over the probe the studs are pushed outward from the center against the spring tension, allowing the tool to slide into position below the shoulder of the probe head. The spring tension forces the studs inward into the engaged position after they pass the shoulder. When the tool is raised the studs stop against the shoulder, preventing the tool from sliding up over the top of the probe. Once it engages the shoulder of the probe it cannot be freed until both probe and fishing equipment are recovered from the drillhole.

Jan 1, 1960

By J. H., R. W. Guard, Westbrook

In 1953 Kornilov and Mints' presented data on thermal expansion and electrical conductivity of the compound Ni3A1 which indicated the possibility of a transformation in Ni3A1 at about 600°C. The present paper gives results of some observations

Jan 1, 1960

By S. H. Moll, R. E. Ogilvie

The investigation of solid-state diffusion phenomena may lead to much information concerning binary alloys. In particular, a study of the concentration gradients present in multiphase diffusion couples can lead to the determination of the solubility limits of the single-phase fields in the phase diagram. The specific concentration gradient which results from the heat treatment of a diffusion couple depends not only upon the time and temperature of diffusion, but also upon the number of phases existing in equilibrium at the diffusion temperature. Such concentration gradients possess sharp discontinuities whose terminal points correspond to the solubilities existing at the limits of the two-phase field in the phase diagram at the diffusion temperature. In general, there will be a discontinuity in the concentration curve for each two-phase field which exists in the phase diagram between the concentration limits of the couple. A number of investigators have analyzed the gradients present in multiphase diffusion couples. 1-8 The iron-titanium phase diagram exhibits a y loop in the temperature range from 900" to 1400°C, and the limit of the a + y field lies at some composition which is less than 1 wt pct Ti for any temperature. It was felt that a diffusion study could yield values not only for the diffusion coefficients involved, but also for the chemical solubilities in the phase diagram. The concentration gradients were analyzed by an X-ray absorption technique developed by Ogilvie.6 The absorption of a monochromatic X-ray beam is measured in steps parallel to the diffusion direction and the resulting intensity gradients are transformed into concentration gradients by applying the laws of X-ray absorption in a binary system. This technique has been applied by ogilvie6 to the systems Ni-Au, Cu-Au, Fe-Cr, and Ni-Cr; by Gelles7 to the systems Be-Fe, and Be-Ni and by Hilliarde to the system Al-Zn. Linear X-Ray Absorption Analysis—The use of X-ray absorption analysis as a tool for determining concentration gradients arises from the fact that the beam is absorbed according to the quantity and species of elements present in the sample and not according to their state of aggregation. This method is more advantageous than the chemical analysis of machined layers since it is less time consuming and less expensive and can analyze a very small area. IF a homogeneous binary alloy (A + B) is analyzed with two different monochromatic X-ray beams I0(2) and lo(2) the following relation between the transmitted intensities, the intrinsic absorption coefficients of A and B for the two different radiations and the weight fraction of each element may be derived.' In (I/Io) (a+b) xa(u/p)a(2) + xb(u/p)8(2) Eq. [1] is independent of specimen thickness and density, but requires that either element A or B possess an absorption edge between the wavelength limits of the two monochromatic beams. I, is evaluated for each radiation by measuring the transmitted intensity through a varying number of foils of a suitable absorber. A plot of the natural logarithm of the transmitted intensity as a function of the number of foils, when extrapolated to zero foils, yields the value of I,. If a plot of the ratio in Eq. [ I] is calculated as a function of xA, then a master curve results. From

Jan 1, 1960

By W. C. Hagel, H. J. Beattie

Variations in the secondary phase reactions of six nickel-and cobalt-base alloys were determined as a function of solu-tioning from 1700" to 2200°F and aging at 1200" to 1800° F for times up to 1000 hr. Room-temperature impact energies and hardnesses were also measured. Precipitation hardening of these alloys results mainly from the grain-interior formation of ? '; M23C6 appears principally as grazn-boundary cells which can be eliminated by intermediate high-temperature aging treatments. Cellular precipitation of ?' occurs up to 1500°F in cobalt-nickel alloys devoid of chromium, where precipitation by this mode can be attributed to a large degree of lattice disvegistery. THE usefulness of nickel- and cobalt-base alloys is dependent on balancing the strength and ductility provided by the solid-solution matrix, dislocation-type subboundaries, grain-boundary phases and genera1 precipitation within individual grains. Since equilibrium relationships for complex austenitic alloys are not easily fixed, a satisfactory balance

Jan 1, 1960

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The kinetics of crack propagation in a hydrogenated high-strength steel at subzero temperatures indicated that cracking progressed in a discontinuous fashion. The delayed failure process thus involves a series of crack initiations rather than the continuous growth of a single crack. The incubation time required for the initiation of delayed failure was controlled by the diffusion of hydrogen. The activation energy for the process was 9120 cal per g-alom. As the test temperature was lowered the incubation time constituted a greater percentage of the total tinze to fracture, and al -50°F the incubation and fracture times were essentially coincident resulting in instantaneous, catastroplzic fracture. A unique feature of hydrogen embrittlement is the delayed failure process in which the material fails under the action of a sustained load even though it is capable of supporting a higher load for a finite period of time.')' Delayed failure of steel and titanium is characterized by an incubation time, preceding the initiation of a crack in a highly localized region, and the subsequent growth of the crack to ultimate failure.3-5 The kinetics of crack growth in hydro-genated high-strength steels have been studied through the use of resistance measurements and have an important bearing on the mechanism of delayed failure. Delayed failure is believed to be merely a facet of hydrogen embrittlement in which sufficient time is allowed during a test for hydrogen diffusion. The current theories employed to explain hydrogen em-brittlement can be grouped into two types. one6-8 explains the embrittlement on the basis of the pressure exerted by molecular hdrogen in lattice voids or defects while the other9-10 attributes the embrittlement to the influence of hydrogen in the lattice. The mechanism used to explain the nature of the crack kinetics in delayed failure is based on the stress-induced diffusion of hydrogen to the area of maximum triaxiality.3 When the hydrogen concentration in this region reaches a critical value, a crack is nucleated. This initial crack propagates instantaneously until stopped by the higher fracture stress of the adjacent material of lower hydrogen content. The continuation of cracking must then await the further diffusion of hydrogen to the new region of triaxiality near the base of the crack where another initiation will occur. From this mechanism it follows that crack propagation is nothing more or less than a series of initiations with limited fracture. The purpose of this investigation was to examine the kinetics of crack growth in an effort to determine whether or not the process was discontinuous. Studies of crack propagation were conducted at low temperatures to retard the diffusion of hydrogen which is presumed to be the rate controlling process in delayed failure. MATERIALS AND PROCEDURE Specimen Preparation—A commercial heat of air-craft quality SAE-AISI 4340 steel, designated as Heat G, was furnished by the Republic Steel Co. in the form of %-in. hot-rolled bars. The material had the following chemical analysis: Composition of 4340 Steel—G Heat C Mn Si Ni Cr Mo 0,395pct 0.82pct 0.29pct 1.76pct 0.85pct 0.25pct Notched tensile specimens with less than a 0.001 in. radius, Fig. 1, were used throughout the investigation. The specimens were heat treated to a 230,000 psi strength level according to the following sequence: a) Normalize bar stock at 1650°F for 1 hr, b) Stress relieve at 1200°F for 4 hr and furnace cool,

Jan 1, 1960

By R. W. Fountain, M. Korchynsky

The precipitation phenomena occurring in cobalt-tantalum alloys have been investigated in the temperature range frm 500" to 1050°C by correlating the results of metallographic, X-ray, micro-and macrohardness, and electrical resistivity studies. The property andmacrohardness,changes were found to depend on 1) general precipitation, and 2) lamellar precipitation. Two new intermetallic phases have been identified: 1) a Co3Ta, a metastable ordered face-centered-cubic compound, and 2) a stable ß Co3Ta phase of hexagonal structure. In addition, the previously reported Co2Ta phase was found to exist in two allotropic modifications: the hexagonal MgZn,-type and the cubic MgCu2-type Laves phases. SINCE a large variety of structures can result as a consequence of the decomposition of a solid solution, predictions on the nature of property changes are difficult, if not impossible, to make. For any rational attempt to correlate properties and structures of a precipitation-hardenable alloy, a detailed understanding of the kinetics of decomposition and morphology of phase separation, as well as knowledge of phase relationships, appears to be prerequisite. Information of this type has been accumulated in the past for many alloy systems, both of theoretical and pastforpractical importance.1,2 Although the presence of intermetallic compounds has been reported in cobalt-base alloys,3 the amount of published information on precipitation-hardenable cobalt-base systems is very limited. A survey of the binary phase diagrams of cobalt indicates that cobalt-tantalum alloys might be of interest as typical of other cobalt-base systems in which Laves phases of the A,B type can be precipitated from solid solution. The present work has been undertaken, therefore, to study the kinetics and morphology of the precipitation reaction in this system and to establish a base for a correlation between the structural aspects and properties in this class of alloys. PREVIOUS WORK The only available phase diagram of the cobalt-tantalum system is based on the work of Koster and Mulfinger. According to these authors, the maximum solubility of tantalum in cobalt is about 13 pct (at 1275°C) and. less than 7 pct at room temperature. Tantalum additions lower the temperature of allotropic transformation of cobalt (about 420°C), and at 7 pct Ta, the high-temperature face-centered-cubic modification (ß cobalt) is retained at room temperature. The precipitating phase was originally designated as Co5Ta2 compound (55.2 pct Ta, about 1550°C melting point), but subsequent investigations by wallbaum5" identified this constituent as the A,B-type Laves phase. Wallbaum's data indicate that there are two modifications of this intermetallic compound: one richer in cobalt (Co2.2 Tao.8)of the hexagonal MgNi, type; and another of a higher tantalum content (Co2Ta) of the cubic MgCu, type. On the other hand, Elliott7 found that the cobalt-rich alloy (CO2.10,Tao.~l) was predominantly the cubic MgCu, type at 800°C and a mixture of both the MgCu2 and the hexagonal MgZn,-type Laves phases at 1000°C. At 1200°C, Elliott found only the MgZn, type while at 1400°C, he observed only the MgCu2 type. At the stoichiometric composition, Co2Ta, Elliott reported only the cubic MgCu2-type Laves phase in the temperature range of 600oto 1600°C. The precipitation of the cobalt-tantalum intermetallic compound is accompanied by a marked increase in hardness. According to Koster's4 data, the Brinell hardness of an 8 pct Ta-Co alloy increases from 230 to 340 upon short-time aging at 800°C. EXPERIMENTAL PROCEDURE The binary cobalt-tantalum alloys investigated contained 5, 10, and 15 pct Ta. The range of tantalum additions was thus slightly broader than the reported minimum and maximum solid solubility limits of tantalum in cobalt (7 and 13 pct, respectively)4 The alloys were vacuum-induction melted in a magnesia crucible using cobalt rondelles and technically pure tantalum sheet as raw materials. Deoxidation of the melt was accomplished with carbon, and the chemical analysis of the alloys is given in Table I. The effect of isothermal aging treatments on the progress of precipitation was studied on samples cut from cast ingots. These samples were solution treated for 2 hr at 1250°C and water-quenched. Aging was conducted in the temperature range from 500" to 1050°C for periods between 15 min and 1000 hr and followed by water-quenching. To prevent contamination from the atmosphere, all samples were sealed in evacuated Vycor or quartz tubes for heat-treatments. For solution treatment, argon at 0.2 atmospheric pressure was introduced prior to sealing of the capsule to prevent collapse at high temperature, and titanium sponge was placed at one end of the capsule to act as a getter. MACROHARDNESS The effect of aging on Vickers hardness (Dph) of

Jan 1, 1960

By Richard H. Jahns

Terminology and Basic Specifications Minerals and closely allied natural substances that are used for personal adornment, as raw stock for the fashioning of ornamental objects, or for other decorative purposes can be referred to collectively as gem materials. Industrial gem materials are those employed directly in various areas of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconstant, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Although many building and monumental stones are undeniably ornamental in their uses, treatment of such material is beyond the scope of this chapter. Substances that lose their identity in use are excluded from the gem category. Thus a transparent crystal of beryl would not be classed as a gem stone if it were treated as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means of distinguishing different gem materials on the basis of their recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquois, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of intrinsic properties, and at the present time all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance desirable characteristics that are present initially. The worth of most synthetic gem stones is founded upon the identity between their major properties and the natural characteristics of the corresponding minerals, just as the pleasing qualities of imitation stones depend upon how well certain of their properties simulate those of more valuable substances. The most important specifications of gem materials represent four basic factors: beauty, durability, rarity, and portability. Beauty, whether expressed as splendor, "purity," attractiveness, or in some other way, is mainly a function of personal response to optical properties such as color, transparency, indices of refraction, and dispersion. Freedom from visible imperfections is important for transparent stones. For some substances beauty depends also upon asterism, opalescence, textural and

Jan 1, 1960

By R. F. Shurtz

The author proposes a method used with some success on a magnesite deposit at Gabbs, Nev. He believes this procedure to be more sound than the blind practice of assigning uniform quality to large, soinetimes vast blocks or ore on the basis of analyses made of a small number of samples. When an ore deposit is evaluated on the basis of core sampling, questions always arise as to how much weight should be given the various sample grades and how the deposit should be divided into specific volumes assigned to corresponding grades. For a tabular deposit it is customary to use the so-called zone-of-influence. This zone is usually defined as the polygon in the plane of the deposit having corners halfway between a given core drill intersection and each of the nearest neighboring intersections. The volume of the ore in this polygon is assigned the analysis obtained from the drill core taken at the intersection. In massive or irregular deposits, volumes of various shapes may be defined with respect to the locations of drill core samples. These volumes may be regarded as three-dimensional zones-of-influence; the theory involved in assigning the values of the central analyses to the ore in the volumes is the same as that used in the case of a tabular deposit. The zone-of-influence method was used in evaluating one of the magnesite deposits at Gabbs, Nev.'-"

Jan 1, 1960

By E. F. Adkins, R. I. Jaffee, C. T. Sims

The effect of oxide dispersions on mechanical proberties of cobalt and cobalt-base powder-metallurgy alloys was investigated. This study shows that oxide dispersions added to pure cobalt greatly improve the high-temperature creep resistance of the metal. Dispersions in powder-metallurgy .cobalt alloys were muck less effective. COBALT is extremely valuable as an alloy base for certain high-temperature applications. Important examples may be found in the widespread use of cast and workable alloys in aircraft gas-turbine engines. With the increases in cobalt production in recent years, greater use may be made of cobalt-base alloys for high-temperature applications, provided

Jan 1, 1960

By R. J. P. Lyon

It is usually assumed1,2 that ore deposition is relatively slow, taking place over tens of thousands of years. Yet many syntheses and phase changes can be completed in the laboratory in a matter of hours, under essentially the same pressure and temperature conditions to be expected in nature. Much has been written about geothermometry, and Ingerson's recent summary2 an hardly be surpassed. Rather than review the whole field, this article will deal specifically with diffusion rates in solid solutions* of the sulfide minerals. In the study and application of temperature-indicating phenomena to problems of ore genesis, the time factor has often been neglected. In the particular case of sulfide systems, the speed of unmixing and diffusion of the constituent phases in the solid solutions has seldom been considered when laboratory data are applied to the genesis of natural sulfide ores. Chalcopyrite and Bornite Intergrowths: Chal-copyrite and bornite are copper iron sulfides often found in association. In many ores the individual grains appear to have mutual boundaries, but bladed intergrowths are quite common. Early workers in the field, " deduced that while these patterns could have been formed by replacement, they could be experimentally reproduced from the unmixing of solid solutions of the two previously homogenized at 475°C. Much of the ore from Roan Antelope mine in the Rhodesian Copper Belt exhibits these bornite-chalcopyrite intergrowths, from which it has been deduced that the ores could have been subjected to a minimum temperature of 475°C. In several recent interpretations,' this temperature rise has been considered to result from a regional metamorphism of an original syngenetic copper-bearing sediment. The same temperature rise to 475 °C was suggested from similar intergrowths in the sulfide- • The general subject of solid solution in structurally similar minerels is treated in many texts'. :' ' and will not be further elucidated. bearing ore from the Happy Jack uranium mine8 on tile Colorado Plateau, although this temperature had a different origin. In 1931 SchwartzV etermined that 475°C represented the unmixing temperature of his bornite-chalcopyrite solid solutions but, more important, that the characteristic intergrowths of bornite and chalcopyrite could be preserved only if the solid solution were chilled quickly to room temperature. This significant corollary has been almost completely neglected by both Davis and Miller.7,8 By suitably decreasing the cooling rate, Schwartz found that the original pattern of the intergrowth was reformed (Fig. 1). The cooling rate was critical. In cooling from 475°C to room temperature in

Jan 1, 1960

By G. D. Gemmell

Effects of solid-sdutidn alloying with titanium, molybdenum, and tungsten at concentrations up to 10 pct on the strength of pure columbium at elevated temperatures (mainly 2000°F) have been investigated by means of creep-rupture, hot-tensile, and hot-hardness testing and recrystallization studies. ThIS paper presents some results from the initial part of a study of the effects of alloying on the high-temperature strength properties of columbium. The elevated-temperature strength characteristics of pure columbium were first studied. Binary alloys of columbium with titanium, molybdenum, and tungsten containing 1, 5, and 10 pct of the solute elements were chosen on the basis of their high melting points, their known solid solubility in columbium, and results of separate oxidation-resistance studies of columbium alloys. EXPERIMENTAL PROCEDURE All the materials used were of highest purity. A typical analysis of the columbium is shown in Table I. Compositions of the alloys are also given in Table I. To evaluate the strength properties of pure co-lumbium and the alloys at elevated temperatures, creep-rupture, hot-tensile, and hot-hardness testing was done on recrystallized material. To prepare the pure metal and the alloys for these tests, 1- 1b buttons were made in a water-cooled copper crucible, inert atmosphere, tungsten arc furnace. Tapered ingots, 3 in. long, were made from these buttons by a skull-casting technique and these were machined to 1/2 in. diam, swaged to 50 pct reduction (pure columbium at room temperature, alloys at lowest temperature possible without cracking, generally in range 1100" to 1800°F) and heated in vacuum (lo-' mm Hg) for 16 hr at 2550°F for re-crystallization and homogenization. The resulting grain diameter was 0.1 to 0.3 mm. The 10 pct Mo alloy casting was not successfully swaged at temperatures up to 1800°F without cracking and was not included in the test program. Creep-rupture testing was done at constant load in vacuum on cylindrical specimens of 0.16 in. diam, using Instron capsules. The pressure at test temperatures was less than 10-1 mm Hg. Hardneas readings taken on the test specimen before and after testing were used as a check on possible gaseous contamination. Hot tensile tests in vacuum on cylindrical specimens of 0.125 in. diam were also made with Instron equipment at a strain rate of 0.067 min.-l. Hot-hardness measurements were taken with a unit constructed at the Du Pont Experimental Station. The test piece, supported on an alumina anvil, and the molybdenum indenter shaft with sapphire tip is heated in a platinum-wound furnace. The load applied to the pyramid indenter is measured by strain gages attached to a proving ring located outside the hot zone. In the measurements reported here the load was I kg. The tester operates in a vacuum of about 10"5 mm Hg and is capable of temperatures up to 1400°C.

Jan 1, 1960

By E. C. Kersey, R. J. Gennone

MetALLOGRAPHIC investigations of composites of zinc alloys and aluminum have been made to study the effects of various thermal treatments on the zinc-alloy grain size and diffusion of zinc into the core material. The use of various alloys of zinc has necessitated the development of a universal etchant which will allow microscopic examination of the zinc grain size regardless of the composition.

Jan 1, 1960

By W. R. Hibbard Jr., R. W. Guard, N. G. Ainslie

Evidence is presented that copper-base solid solutions of different solutes having equal grain sizes, no preferred crystal-lographic orientation, equal electron-atom ratios, and, within experimental scatter, identical initial yield strengths, need not have identical stress-strain curves at strains larger than about 0.04. The stress-strain behavior is rationalized in terms of the proposed Suzuki chemical interaction between solute atoms and extended dislocations using what is thought to be a somewhat different means of representing stress-strain data. ALTHOUGH the effect: of alloying element upon the strength characteristics of sold solutions is a subject which has received considerable attention in the past, the exact relationships between the common deformation parameters and certain common variables are not really known in some cases. As a result some of the experiments reported in the literature in which these variables are inadequately controlled lose some of their persuasion regarding underlying principles. Nonetheless, facts are known which bear pointing up: When the true stress, a, and true plastic strain, E, of tensile deformatic~n are plotted on a double logarithmic coordinate system, one may observe a straight-line relationship at strains greater than 0.02. The form of the curve in the linear region is given by a = Ken! where a represents true stress, E, true strain, and K and tn, constants. If the relationship holds, K and m define the flow characteristics of the material being tested. m and K, however, may vary with other parameters. Hollomon found that in a-brass, m is influenced by grain size. French and HibbardZ found in alloys of copper that inverse relationships existed between m and 1) the solute concentration for a given solute, 2) the 0.01 yield strength, and 3) the constantK. Lacy and Gensamer3 observed (du/d~) (= U/Em) to increase with increasing values of K in systems of alloyed ferrites (although with considerable scatter of data which may be attributed to uncontrolled grain size). Brick, Martin, and Angier* deduced in copper-base alloys a straight-line relationship (with some scatter) between the change in the Dph number due to solid-solution strengthening and the change in the Dph number due to work hardening which suggested that copper-base alloys having equal yield strengths might have identical stress-strain curves in the plastic flow regions. French and HibbardZ concluded that the yield strength of copper-base solid solutions is the proper basis for comparing the effects of solute elements. Also, Allen, Schofield, and ate' showed that, within their experimental variation, copper-base alloys of zinc, gallium, germanium, and arsenic having the same electron-atom ratios have the same true-stress true-plastic strain curves. Dorn, Pietrokowsky, and ~ietz' also found that with aluminum-base alloys the stress-strain curves in the flow regions are approximately the same if "equivalent" concentrations of alloying elements are used. Solute valence and lattice parameter distortion were the parameters used to determine equivalency. The present report describes an investigation in which an attempt was made to obtain copper-base solid-solution alloys of four solute elements having within close tolerances equal grain sizes and yield strengths, and to see if the level of yield strength does indeed define the flow curve regardless of solute type. During analysis of the data certain unexpected features of the stress-strain curves became apparent which gave rise to some speculation and are discussed at length in the paragraphs that follow. EXPERIMENTAL PROCEDURES Alloy Preparation—Using the data of French and HibbardZ as a first approximation, four different binary copper-base alioys were designed so as to have the same yield strength. In addition, other alloys were prepared in which the solute aoncentrations varied slightly from those calculated above so as to span a range of yield strengths, see Table L The yield strengths of all alloys prepared except the copper-tin alloys were subsequently found to Lie fairly close to one another. The copper used in the alloys was produced by the American Smelting and Refining Co. and was of very high purity (99.999 pct). The alloy additions and their initial purities are as follows:

Jan 1, 1960

By Henry J. Kaiser

A few months ago I had the honor of addressing the Society of Mining Engineers annual banquet in Sun Francisco. I have since been asked to amplify some of the remarks I made at that time concerning the management policies of the Kaiser organization and various aspects of our corporate thinking. This is a difficult task for an insider like myself. I look at the different companies, and the men who run them, and it is hard to think of these men in terms of policy or procedure. Actually I prefer the term management philosophy to either policy or procedure. My father, Henry J. Kaiser, is not only the founder but the guiding spirit of our organization. His philosophy, and in turn that of the organization, centers around two concepts, service and accomplishment.

Jan 1, 1960

By H. D. Keiser

Minor industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz, and nonfuel gases (air, helium, carbon dioxide). Alum Minerals The natural alums comprise a group of hydrated double sulfates, the most important of which are potash alum, KAI(S04)2.12H20, the "alum" of popular usage; ammonium alum, (NH4)AI(SO4)2, known mineralogically as tschermigite; and soda alum, NaAI(SO4)2.12H20. Kalinite, KAI(SO4)2.11H20, and mendozite, NaAl(SO4)2, 11H20, are fibrous monoclinic alums, distinct from the isometric species potash alum and soda alum.4 Alunite, KAI3(S04)2(OH)6, also known as alumstone or alum rock, has been used as a raw material in the manufacture of alum since early times. All the natural alums are highly soluble and occur as surface evaporation products in arid regions or in sheltered places. Potash alum, together with the other natural alums, commonly occurs as an efflorescence or crevice filling in argillaceous rocks and brown coals that contain disseminated pyrite or marcasite. The mineral is derived by the action of sulfuric acid, formed during the weathering of the sulfide, upon alkali-rich aluminum silicates. Ammonia alum is found chiefly in lignite or broad-coal beds and bituminous shales. Alunite is most commonly associated with acid volcanic rocks, where the rock has been largely altered and alunite formed owing to the presence of sulfuric acid solutions or vapors. Aluminum sulfate, which for most uses is the essential ingredient of alum, may be found in saline residues resulting from the evaporation of natural water and may be formed by the action of acid waters upon aluminous rocks. A deposit of natural potash alum occurs in an irregular network of veins associated with sulfur in rhyolite in Esmeralda County, Nevada, about 35 miles west of Tonopah and 10 miles north of Silver Peak. Alum was recovered at a plant operated on the property between 1920 and 1923 by crushing the ore to ¾ in., grinding to minus 80-mesh, and counter-current leaching; the resulting alum solution was then filtered and crystallized. Alunite was of much interest during World War I as a source of potash and during World War II as a source of alumina. The wellknown deposits at Tolfa, Italy, are veins in trachyte and have been the basis of alum manufacture there since the middle of the fifteenth century. Pure alunite is insoluble in water and in common acids, but if it is heated to 500°C it loses its water of hydration, and the residue consists largely of anhydrous potash alum, part of which is readily soluble in water or acids. If the heat is increased beyond 500°C, most of the sulfur combined with the alumina is released as oxides and the residue consists of potassium sulfate and alumina. Thus, either potash alum (and aluminum sulfate) or potassium sulfate and alumina may be made. In the

Jan 1, 1960

By Glenn R. J

Treatment processes are outlined for the recovery of rutile and zircon from the heavy mineral-bearing sands on the east coast of Australia. With the exhaustion of the higher grade deposits and the imposition of more rigid specifications for the finished products, strict metallurgical control has become necessary.A description is given of the methods used by The Titanium Alloy Manufacturing Co. Pty. Limited to control the operation of suction dredging, of wet concentration using fans and spirals, and of dry separation using high tension and electromagnetic processes. By applying these methods a plant designed for an output of 15,000 tons of rutile per year has been tuned to produce over 20,000 tons of rutile and a corresponding amount of zircon.Details are given of (a) the method of drilling to determine the extent and grade of the ore bodies, (b) a simple electrically-timed pneumatic automatic sampler, and (c) the methods developed for the physical estimation of quartz, rutile, zircon, ilmenite and "others" in the products of plant operation.The method used for calculating the metallurgical balance and the forms used for the reporting of production results are presented.Examples are given which show the value of this detailed production and metallurgical control of plant operation.INTRODUCTIONThe organization which is now known as "The Titanium Alloy Manufacturing Co. Pty. Limited" (T.A.M.Co.)-a subsidiary of National Lead Company-commenced operating at Yamba, N.S.W., in 1935. A mixed natural concentrate was at first simply dried and bagged and later was upgraded by the removal of silica and the lighter heavy minerals on shaking tables and, after air-drying, was bagged for export. At that time zircon was the most wanted constituent.

Jan 1, 1960