Search Documents

By D. B. Masson

THE martensitic transformations occurring in ,B AgCd as a result of cold working at room temp.. a-ture and cooling below room ten1erature have been reported by Masson and Barrett.1 These authors found that simple cooling to 127°K caused body-cen-tered-cubic AgCd containing 53.0 at. pct Ag to transform to an orthorhombic structure, while mechanical deformation at room temperature was found to induce a hexagonal structure. Furthermore, they observed that the temperature at which martensite first appeared on cooling, Ms, and that at which the transformation was complete, MI, as well as the corresponding temperatures for the reversion on heating, As and Af, could be ascertained to ± 1°K, although they report these temperatures only for the alloy containing 53.0 at. pct Ag (51.96 wt pct). In the work reported here the temperature range of the transformation on cooling was studied as a function of composition, and further consideration was given to the relationship between the original bcc structure and the transformation-induced hexagonal and orthorhomic structures. EXPERIMENTAL PROCEDURE All samples studied were in the form of annealed 300-mesh powder and were prepared from the constituent metals in the manner described previously.1 The compositions in weight and atomic pct are listed in Columns 1 and 2 of Table I. Method of determination of transformation temperature was the same as utilized previously1—measurement of the intensity of X-rays diffracted by the transformation product. A diagram of the low-temperature sample mount is shown in Fig. 1. This mount was made to fit a GE model XRD-3 X-ray diffraction unit. The powder sample was varnished to a flat surface on a copper sample holder at A. This sample holder was soldered to a brass rod, B, which was in turn soldered to a second copper rod, C. Rod C could be cooled to 78°K by inserting it into a reservoir of liquid nitrogen, D. A heater coil of nichrome wire was wound at E on the sample holder, and by varying the current through the heater a thermal gradient could be maintained along brass rod B. Sample temperatures from 78°K up could be attained and held as long as needed. The sample holder and nitrogen reservoir were insulated by Styrofoam, F, and the sample itself was protected by two radiation shields, G. The X-ray beam entered and left the sample chamber through windoys in the supporting container at H and I. Sample temperatures were measured by a calibrated copper-constantan thermocouple varnished to the sample holder just out of the beam at A. The low-temperature structure had been found to possess orthorhombic symmetry1 and the expected positions of the diffraction maxima were known. Therefore the sample was aligned in the X-ray beam and the Geiger counter of the spectrometer set to receive the most intense orthorhombic reflection without an adjacent interfering cubic reflection. This

Jan 1, 1961

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By E. C. Speers

The Ray Mines Division has a long and illustrious history beginning in 1911, as one of the early underground block caving copper mining operations. The tonnage mined from the beginning of operations, increased from about 8, 000 TPD in the early years to the present daily tonnage of 22, 500 tons, mined by open pit methods. The Ray basic milling practice has been relatively unchanged since 1927 when the sulphide-flotation process was introduced at Ray. The leach-precipitation-flotation process introduced in 1956 has been the only major process change. The change from underground to open pit' mining was accompanied by a renewed drilling and exploration program which developed large tonnages of low grade copper ores both in the porphyry and the diabase. The ore bodies as outlined were of such a grade and size that it soon became apparent that economical operations could not be developed with the lower tonnage rate. Also that in order to develop these newly proven ores, it would be necessary to move the Ray crushing plant, the Ray. supporting shops, offices, a substantial part of the Ray townsite, and would also involve the rerouting of Mineral Creek, a typical Arizona stream which is dry most of the year but can flow as high, as 8, 000 second feet in the rainy season. This paper describes those changes in flow sheet made necessary both by the increased tonnage .and the requirement to move as much of the crushing facilities from the Ray area as practical in order to free the mine for the extension of its physical limits.

Jan 1, 1961

By George M. Hamilton

The gas producer actually dates back far beyond the period from which we first find recorded data. A partial production of producer gas can take place in any type of solid fuel grate equipment, such as a boiler, or even a fireplace if a sufficiently deep fuel bed is provided. Those of us who have watched a coal fire burning in the hearth, have no doubt noticed at times, the gases liberated by the heat burning on or near the surface of the fuel bed. So far as we know, the first gas producer was built by Bischof in Germany in 1839, followed by Ebelman in France in 1840, and Ekman of Sweden in 1845. The first large industrial development in the use of gas producers was When the two Siemens brothers of Germany patented their first combined gas producer and regenerative furnace in 1861, thus opening up the field for the use of raw, crude producer gas in heavy furnace work. In the years 1879-1881 J, E, Dowson, of England developed a producer gas cooling and cleaning plant, which extended the scope of application of producer gas to make possible its use in small furnaces and gas engines.

Jan 1, 1961

By G. Pomey

Heat-resisting chromium steels and alloys treated at 825° or 9.50°C (1527° or 1742°F) in a carburizing atmosphere exhibit an extensive carbide precipitation. This carbide precipitation may be succeeded by the FeCr a phase or by a carbide with a higher carbon content. Point analyses carried out with an electron mi-croanalyzer make it possible to study the depletion of chromium in the matrix after precipitation has occurred and to determine the chemical composition of carbides. In particular the content in the carbides of Fe, Ni, and W, elements which substitute Cr, can be accurately determined. HEAT-resisting chromium steels and alloys employed in the construction of gas carburizing and carbonitriding furnaces are subjected to a succession of oxidizing atmospheres during heating and cooling and to carburizing atmosphere during isothermal stage. Such a sequence of thermal cycling causes embrittlement and corrosion in the furnace materials. A quantitative study of the structural changes induced in the furnace materials has not received much attention in the past. However, utilization of the electron probe microanalyzer and other modern techniques has permitted a point analysis of the various phases formed and to follow their relative evolution. This paper gives results as regards the nature and composition of the carbide precipitation and the distribution of chromium in the matrix during only the carburizing periods. The structural changes subsequently produced during oxidizing periods will be presented eventually. METHODS AND MATERIALS Metallographic, X-ray diffraction and Castaing electron-probe microanalysis1 techniques have been employed to study carbide precipitation and evolution and the changes in the composition of the matrix in heat-resisting steels and alloys.

Jan 1, 1961

By R. H. Pemberton

The principle of airborne electroniagnetic prospecting is well-known. 'The basic geonhysicai texts in inost cases discuss the main elements involved in electromagnetic prospecting. However. there is ceriainlv iittle information available to the public concerning he present types of airborne eiectromagnerlc systenis being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficuit for those people not conducting such operations to understand thoroughly the iarge variation in the electromagnetic instrunlents available. Basically, the aeriai electromagnetic induction method utilizes a primary or transmitting coil through which is generated an alternating magnetic field at a frequents: generally of the range of 100 to 2000 cycies per sec. This primary field links with buried conductors and generates eddy currents within them. These eddy currents in themselves generate a secondary magnetic field of the same frequencv, but generally nut-of-phase with respect to the prinlarv field. This secondarv field is detected above the ground in the pick-up or receiver coil which is tuned to the frequency of the current applied to the primary transmitter coil. One of the main problems in the development of an airborne electromagnetic system is that of maintaining constant coupling between the cransmitting and receiving coil systems. Any variations in the coupling due to relative motion between the two coils will result in an in-phase signal being induced in the receiver coil. [However, any variation in the coupling does not result in an out-of-phase signal change in the receiver coil. The first airborne eiectromagnetic svsteins which were developed utilized a large prlniarv coil set up on the aircraft with the receiving coil being towed behind in a bird, generally at the end of a cable of about 500 ft. in length. It is possible with such a system to record the out-of-phase or quadrature responses more readily than the in-phase re-sponse. One system utilizes a dual frequency method, wnereby the out-of-phase responses at two frequencies are recorded. Another system used today records a single-frequency olrt-of-phase response. Recentlv home companies have succeeded in measuring from ne air both the out-of-phase and the in-phase components. The usefulness of recording in-phase is weil-known, but unfortunately this is difficult to obtain in any towed-bird system. In order to measure the true in-phase signal, the most straightforward system is that in which both the transmitter and receiver coils .Ire affixed in space so that there is little or no relarive motion between the two coils. THE FLIGHT SYSTEM The particular system which Canadian Aero Service is using at present is mounted on a Sikorsky S-55 helicopter (Fig. 1). A record of both the in-phase and out-of-phase responses is made at a frequency of 390 cycles per sec. The transmitter coil is set on a boom mounted in the front of the helicopter; the receiver is set on a tail boom extending back from the helicopter. Separation between these coils is about 65 ft. The two coils are mounted in a vertical co-axial relationship. Having the transmitting coil in a vertical plane ensures that maximurn coupling will occur with vertical conductors rather than flat-lying conductors. Having them mounted as they are in a co-axial relationship on the helicopter ensures that maximum response will occur when the flight direction is orthogonal to the strike direction of a given conductor. The present sensitivity of the Em system is 20

Jan 1, 1961

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961

By J. B. Gayle

Numerous investigators have studied the addition of inert4 substances to coking blends. Generally, the results have yielded trends applicable only to the particular coals and inerts studied. Recently, somewhat more general results were obtained for cokes produced from blends containing added inerts, using the sole-heated oven. The present investigation represents an extension of this work to include a wider range of inerts and to determine the applicability of the various conclusions to cokes produced with the Tuscaloosa oven. The results indicated that an increase in dry-coal charge density of 1 pound per cubic foot (p.c.f.) caused a corresponding change in the hardness (1/4-inch tumbler index) of Tuscaloosa oven cokes of 0.9 percentage points. This value compares favorably with the value of 0.7 determined previously for the sole-heated oven and Bureau of Mines-American Gas Association (BM-AGA) retort.

Jan 1, 1961

[Officers and Committees of the Society of Petroleum Engineers 1 Officers and Staff of the AIME 2 . Officers of AIME Sections Predominantly Petroleum in Membership 3 AIME Local Sections and SPE Regional Organization Maps 5 Alphabetical List of Members 7 Geographical List of Members 102 Advertisers' Index 133]

Jan 1, 1961

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

By John J. Reed

Since the beginnings of, the human struggle for survival and improvement, mining has been one of the basic endeavors of life. Until relatively recent times it was classed as an art. Now we are at work trying to, raise mining to the level of an engineering science where it belongs if we are to prosper. It should be self-evident that this goal can be attained only through industrial progress: based on education and research. It is true that our industry, left to itself, will develop a few new ideas and techniques through the years. However, we mining' engineers are relatively few in number compared to the other disciplines, and the rate of our improvement by such "accidental" discoveries is simply tooslow to keep pace with the rest of our technical civilization. It will be evident in the remarks that follow, that the rapid development of mining education, research, and the industry are extremely interdependent, and will be largely controlled by the amount of cooperation, support, and cross-fertilization that can be developed among all three.

Jan 1, 1961

*J. H. Brennan, Union Carbide Metals Company, Niagara Falls, N. Y. S. B. Casey, Jr., Swindell-Dressier Corporation, Pittsburgh, Pa. C. M. Cosman, Vanadium Corporation of America, New York, N. Y. H. E. Dunn, Vanadium Corporation of America, New York, N. Y. C. S. Finney, Eastern Gas and Fuel Associates, Boston, Mass. M. O. Holowaty, Inland Steel Company, East Chicago, Ind. John Mitchell, Eastern Gas and Fuel Associates, Boston, Mass. Leo F. Reinarts, Armco Steel Corporation, Middletown, Ohio H. E. Rowan, Dwight-Lloyd Division, McDowell Company, Inc., Cleveland, Ohio R. W. Shearman, The Metallurgical Society of AIME, New York, N. Y. C. M. Squarcy, Inland Steel Company, East Chicago, Ind. F. Weston Starratt, The Metallurgical Society of AIME, New York, N. Y. A. B. Wilder, National Tube Division, United States Steel Corporation, Pittsburgh, Pa. *Deceased

Jan 1, 1961

By K. K. Kelley

This report contains heat-content values for hexagonal crystalline germanium dioxide between 298.15° and 1,350° K., and for germanium dioxide glass between 298.15° and 1,800° K. experimentally determined by the Federal Bureau of Mines. No similar data for these substances are to be found in the literature. The heat-content and corresponding entropy-increment data are presented both in tabular form and by equations. Free energy of formation values are estimated for germanium dioxide glass at 298.15° and 1,800° K.

Jan 1, 1961

By Donald W. Mitchell

Studies were made in the Bureau of Mines Experimental coal mine to evaluate the effectiveness of a few extinguishing agents and techniques for controlling a fire on a simulated mining machine. The investigation showed that water containing an alkali-metal salt or a surface-active (wetting) agent was more effective than water alone. For close attack, fog applications was the most effective technique studied; high rates of agent application controlled the fire more quickly than low rates. The ability to control the fire increased as the distance of attack decreased. Dry powders controlled the fire when applied by shovel but not when applied airborne by rock-dust distributor or by hand fire extinguishers. Dry alkali-metal salt powders (potassium and sodium bicarbonates and sodium tetraborate) quenched the fire more readily than limestone dust. In each instance the finer powder, the greater its effectiveness. In an open ventilated entry, smoke and hot gases backed against the air currents. An airspeed of 230 feet per minute was required to permit approach to within 10 feet of the fire. At lower airspeeds, approach could be made by extending the brattice across the bottom two-thirds of the entry, by pushing the smoke ahead with water sprays, or by discharging dust from a rock-dust distributor. In a dead-end entry, the fire was approached to within 30 feet by coursing fresh air along an airtight line brattice; however, it was safer, easier, and less time-consuming to attack the fire from a fresh-air base 100 feet away with a solid stream or by high-expansion foam; the latter method was more effective.

Jan 1, 1961

By J. P. McCullough

In 1943, the Federal Bureau of Mines began a program of thermodynamic investigations of petroleum constituents and related compounds. These systematic, long-range studies, which were conducted in the thermodynamics laboratory of the Bartlesville Petroleum Research Center and are still continuing, have resulted in a substantial quantity of data valuable to the petroleum industry and science in general. As separate phases of these studies were completed, the findings were promptly reported in the scientific press. During the past 16 years, 89 journal articles, giving the results obtained for individual compounds and small groups of related compounds, were published, mainly in the Journal of the American Chemical Society and the Journal of Physical Chemistry. In addition, members of the Bureau staff have contributed six chapters to specialized reference books. This circular, prepared in response to many requests, lists these 95 published papers, giving an abstract of the contents of each, as well as titles, authors, and literature citations. The journal articles are listed in the order of their preparation, which closely approximates the chronological order of their publication; hence, the item number to the left of each citation corresponds to the assigned contribution number. For the convenience of the reader, the abstract section is followed by a condensed bibliography, arranged alphabetically by senior author and keyed to the abstracts by appropriate contribution numbers in parentheses after the entry.

Jan 1, 1961

By F. C. Bond

Since the Third Theory of Comminution was presented eight years ago (I) it has found increasing use in crushing and grinding problems. The practical utility of its wok index equation is quite generally acknowledged (2). However, its theoretical basis has been questioned in at least three technical articles (3) (4) ('). The purpose of this paper is to present experimental proof that it is scientifically correct. Particles under compressive stress are strained and deformed. They absorb strain energy, and when this locally exceeds the breaking strength, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends and splits the rock, releasing the strain energy as heat. The initial energy flow causes additional crack tips in highly strained areas. If the compression is rapidly applied by impact, crack tips may form before the strain energy has reached equilibrium in the particle, thus decreasing the total work input required for breakage. The energy necessary to break is essentially the energy necessary to produce crack tips, since the energy necessary to extend the cracks to breakage is already present as strain energy in the deformed particles. After breakage nearly all of this energy appears as heat. The crack length cannot be measured directly. However, in particles of regular and similar shape the crack tip length is considered as equal to the crack depth, or crack extension necessary to break, so that the crack length equals the square root of one-half of the surface area. The Third Theory states that the useful work done in crushing and grinding is directly proportional to the total length of the new cracks formed. It can be confirmed by showing that a constant work input produces a constant length of new cracks when reducing the same material to different product sizes. This is done in the present paper on a wide variety of material. The constant work input was supplied by one revolution of the 12" x 12" laboratory ball mill used in making grindability tests by the Allis-Chalmers method (12) (13) The new crack lengths produced per mill revolution were measured from all available grindability test results at 28, 35, 48, 65, and 100 mesh on fifteen different ores, and were found to remain substantially constant for each ore at all mesh sizes. A new technique is used for the measurement of crack lengths. Size distribution plots of the mill feed and product are made by the Third Theory method (9) and the crack lengths are obtained from these plots by the procedure described in the present paper. The energy input required to produce a unit length is of fundamental importance in the size reduction of brittle solids. The crack length Cr is expressed in centimeters per cubic centimeter of solid material. It bears a definite relationship to the external surface area of the crushed or ground solid. A uniform particle shape must be assumed before the surface area and crack length can be evaluated. In this paper it is assumed that the relationship between the surface area and the particle volume of a particle d microns in diameter is the same as that of cube d microns on a side. The external surface areas of particles with a cubical breakage probably agree approximately with this rule, and correction factors can be applied when physical measurements of the surface areas are available for comparison. However, the assumption of equivalent cubes has been found satisfactory for most calculation purposes. Assuming equivalent cubes, one cubic centimeter of particles d microns in diameter will have a crack length Cr of v30.000/d centimeters, and a surface area of 60,000/d square centimeters. The specific crack length is thus equal to the square root of one-half the specific surface area. Where Sa is the surface area in square centimeters per gram and Sg is the specific gravity of the ground solid, then Cr = vSg . Sa/2 = 173.2/ vd (1)

Jan 1, 1961

By R. A. Nadler and

Specimens of Ti-155A (Ti-5Al-1.3Fe-1.3Cr-1.2Mo), Ti-6Al-4V and Ti-4Al-3Mo-1V were hydrogenated, aged to high strength levels, and subjected to notched stress-rupture tests and tensile tests at two strain rates. Both Ti-6Al-4V and Ti-155A were relatively unaffected by hydrogen in amounts exceeding those found in commercially -produced material. Inconsistencies in the data and a relatively low initial level of ductility prevented an accurate determination of the hydrogen tolerance for aged Ti-4Al-3Mo-1V, but there was no evidence that this alloy was any more susceptible to hydrogen embrittlement than Ti-155A and Ti-6A1-4V. THE metallurgical literature has been considerably enriched in the past five years by the publication of the results of many investigations which were concerned with the effects of hydrogen on titanium and its alloys. Although it is not the authors' intention to provide a complete literature survey of this vast field, it is worthwhile to summarize briefly some of the important factors which influence the embrittling phenomenon in a - B alloys. Some of the influencing factors are those of strain rate, temperature, and composition. Hydrogen embrittlement in a - B titanium alloys is now believed to be a strain-induced phenomenon, and whether or not embrittlement occurs at high hydrogen levels depends largely upon whether sufficient time is available for hydride precipitation. This condition is fulfilled by tensile testing at very slow strain rates or by rupture testing smooth or, preferably, notched specimens over relatively long periods. Conveniently, maximum embrittlement occurs at or near room temperature. The presence B - stabilizing elements, in amounts sufficiently small to prevent an all -B or nearly all -P condition, promotes hydrogen embrittlement and this tendency is believed to be related to the amount of a - B interfacial area present. Aluminum, by increasing the solubility of hydrogen in A titanium, greatly reduces the danger of hydrogen embrittlement, while oxygen has been shown to have detrimental effects.' The preceding discussion is based on experimental work performed on annealed a - P alloys. This early work has shown that annealed Ti-6A1-4V and Ti-155A are relatively insensitive to the embrittling effects of hydrogen.' Although no work has been reported on annealed Ti-4A1-3Mo-lV, the alloy would be expected to exhibit somewhat the same insensitiv-ity as Ti-155A. In sharp contrast to the voluminous literature on annealed titanium alloys is the paucity of reported investigations on materials receiving commercial heat-treatment cycles. To date, the most notable contributions in this field have arisen from two separate investigations on Ti-3Mn-1Fe-1Cr-1V-lMo, the so-called 3Mn comple~. These investigations

Jan 1, 1961

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961