Search Documents

By Paul J. Bennett, James E. Castle

The kyanite minerals, including kyanite, silimanite, and andalusite, are anhydrous aluminum silicates with the formula Al2O3SiO2. lumortierite and topaz are also included in this group because they are closely allied in composition and thermal behavior. However, leither are mined commercially today. They ire typical metamorphic minerals which are found in metamorphic rocks on every continent. Kyanite minerals are prized chiefly for their refractoriness and are important components in a broad range of acid refractory products, especially in mortars and castables. World production of kyanite minerals is currently about 250,000 tpy and has been increasing at the rate of 3 to 8% a year for many {ears (Anon, 1972). While kyanite minerals lave widespread occurrence, the consumption of kyanite minerals is concentrated in the relatively few highly industrialized areas where refractories are manufactured, and which in turn are typically close to the major iron and steel producing regions of the world. Thus northern Europe, England, the United States, and Japan are the principal consumers of refractories and kyanite minerals. Of these countries only the U.S. is a significant producer. The largest use for domestic kyanite, both raw and calcined, is in the manufacture of refractory mortars, cements, castables, and plastic ramming mixes. In these applications kyanite constitutes from 10 to 40% of the mixture, the balance being refractory clays and coarser grog materials. A certain proportion of raw kyanite is used to offset the shrinking of the clay binder, whereas the calcined kyanite is used in the coarser sizes for body. Certain high grade refractory shapes and kiln furniture are composed chiefly of graded sizes of calcined kyanite bonded with a little ball clay. In most applications, however, kyanite is used only to fortify the mix or as a minor ingredient. Some manufacturers of mullite brick use domestic calcined kyanite for the fine-grained portion of the brick, but seldom in quantities exceeding 10% by weight. Kyanite is used by ceramic manufacturers of wall tile and sanitary ware to offset shrinkage and cracking after firing. Indian kyanite has traditionally been used to make the coarse grog sizes needed for the manufacture of mullite brick, and for the grog portions of mortar, cement, and castable mixes. It has been largely replaced, however, by synthetic mullite, high fired flint, and diaspore clay or calcined bauxite for other applications. Indian kyanite is available in lump as well as in granules and concentrates, as are sillimanite materials from India and South Africa. Andalusite is available as 8 mesh granules and as fines with chemical analyses not unlike those of domestic kyanites. From time to time and from place to place minor amounts of other aluminum silicate minerals such as dumortier- ite, topaz, and pyrophyllite have been made available at various prices and specifications, but have not been significant factors in the refractory industry. A mixture of kyanite and sillimanite of relatively fine grain-size and of low iron content was at one time offered to the molding sand industry by the Du Pont Co. as a byproduct from their deposits of heavy

Jan 1, 1975

By Robert E. Murray

It's indeed a pleasure for me to speak to you today about the development and operation of large-scale surface coal mining projects in the western United States. It is an exciting story about American business working to solve a critical national problem -- the energy shortage -- through research, new technologies, financial innovation, and imaginative management. The North American Coal Corporation -- the second largest independent mining company and ninth largest United States coal producer -- is proud to be a part of this story. Our operations in North Dakota reflect the coal industry's Western activities. So, today, I would like to focus on our planned involvement in that state. I'll briefly survey why North American is developing large- scale surface mining in North Dakota, and I will outline the many problems associated with this coal development and how we are working to solve them. Finally, I will look at the financial and management techniques we are using to make it all work. In short, I'm going to present a case study of Western coal mining. Let's begin by looking at the reasons we are in North Dakota. The United States Bureau of Mines estimates that 44 per cent of the nation's total recoverable coal deposits underlie the three Northern Great Plains States of North Dakota, Montana, and Wyoming. We estimate that North Dakota alone has about 25 billion economically surface-mineable tons of coal with today's technology. North Dakota has the energy that could keep our factories running and our homes lighted In the years ahead.

Jan 1, 1975

By Stanley J. LeFond, Neal Davis

Drilling an oil well or most other types of drilling or coring is no longer a simple and uncomplicated operation. Drilling today at depths which exceed 30,000 ft is hazardous and requires personnel with long and varied experience in drilling. It also requires extensive experience and knowledge in the use of materials which are added to the drilling fluid or "mud," more often than not materials utilizing an industrial mineral. The drilling fluid can vary from a simple mixture of water and "mud" to a very sophisticated, scientifically compounded drilling fluid. Industrial Minerals Used in Drilling Fluids Industrial minerals which are commonly used in oilwell drilling and completion are listed on [Table 1]. The most important minerals, determined by sales, are bentonite and barite. The other minerals listed are either used to achieve a specific purpose or are used regularly but in limited quantities. The main suppliers of drilling fluids internationally are Magcobar Div., Dresser Industries, Inc.; Baroid Div., National Lead Co.; IMC Drilling Mud Co., (a subsidiary of International Minerals and Chemicals Corp. and Halliburton Co.) ; and Milchem, a division of Baker Industries. Most of the industrial minerals are found in North America, with barite mines and processing plants located in Nevada, Arkansas, Missouri, and Arizona, and bentonite mines near Graybull, Wyo. Other mines, such as those in Nova Scotia, are capable of shipping to South America and to the European and Middle East countries. Most of the materials processed by any of the suppliers must conform to specifications set by the American Petroleum Institute (API) or the Oil Companies Material Organization (OCMA). These specifications provide for uniform physical and chemical properties of the materials to be sold on the open market.

Jan 1, 1975

By J W. Edl, F C. Wu

In instrumented model rock blasting experiments in granite blocks, best fragmentation results were obtained when delays between holes were 1 to 2 milliseconds per ft. of burden and when a rectangular shothole pattern was used with spacings larger than the burden. Effective fragmentation in multiple hole blasts seemed to depend primarily on the full development of the crack network around each hole before the charge in the next hole was detonated. The test results showed that simultaneous or almost simultaneous initiation of shotholes in bench blasting resulted in poor fragmentation.

Jan 1, 1975

By William P. Harris

The Lincoln Terminal System is described as a device with the capability to deliver technical information, monitor student performance, and assure learning in industrial training. An experimental unit, the LTS-3S, was constructed and delivered to the Bureau of Mines with appropriate lesson material for a test of feasibility and acceptability of this form of training in the mining environment. Operations were conducted at two mine maintenance schools. The overall results were that (1) there was a substantial improvement between tests before and after self-training on the LTS, (2) students found this an acceptable way to learn, and (3) reaction by training personnel and supervisors was favorable toward the feasibility and advantages of using the LTS in the mining environment. Transfer of the LTS to industry depends on availability of reliable units and adequate lesson material. The requirements for authors of training materials were established based on advice from mine training experts, formal analysis of lesson development procedures, and experience from efforts in lesson development at Lincoln Laboratory-It was concluded that experienced mine training instructors were best qualified to proceed effectively and economically to format instructional material for the LTS, if supported by well-designed facilities and services. Discussion with mining experts confirmed the desirability of generating training materials and delivering instruction at distributed locations to meet local training needs and in direct support of industrial operations.

Jan 1, 1975

By W. D. Dietzman

This Bureau of Mines report presents a continuation of statistics pertaining to distribution of petroleum reservoirs (or fields), wells, and production by depth and producing rate classification in the United States. These statistics show the change that has occurred since results of a similar study were published by the Bureau of Mines in 1967. Data are presented in tabular form by State for the 18 principal oil-producing States and by subdivision for the two largest oil-producing States, Texas and Louisiana. Tabular summations and graphical illustrations are presented for the Nation. The data are classified by 4-barrel-of-oil-per-day rate increments up to 36 barrels and one increment of greater than 36 barrels of oil per day and by 2,000-foot depth increments up to 8,000 feet and one depth increment of greater than 8,000 feet. The overall average producing rates for States and the Nation have been published for many years, and although such rates are useful, they are very general descriptions of producibility. A breakdown of production, wells, and reservoirs by various depths and rates and by State or by State subdivision provides a more detailed description of producibility.

Jan 1, 1975

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By Karl R. Becker

A variety of commercial detonators (fuse type and electric instantaneous and delay types) were subjected to impact and thermal stimuli to determine initiation stimulus levels and the dominant parameters in resistance to initiation. In the impact trials the detonators were impacted along their length to find the most sensitive region; threshold initiation limits obtained for these regions ranged from 3.47 to 20.82 joules (2.6 to 15.4 ft-lb). The friction sensitivity of the explosive component was an important parameter in determining sensitivity; various construction features of nonexplosive components played a role as well. In the thermal sensitivity trials, the detonators were heated from ambient to 100° C at an average rate of about 1.0° C/min, and thereafter at 0.5° C/min until they exploded; the explosion temperatures observed ranged from 121° to 188° C. These temperatures correlated quite well with the reaction temperatures of certain characteristic explosive components used by different manufacturers. The data also indicated an effect of confinement on explosion temperatures of detonators.

Jan 1, 1975

By Quinlan M. J, Ratcliffe J. S

Chemical kinetics is a dependent process which usually correlates the rate at which a reaction proceeds with the mechanism descriptive of the manner by which reactive particles interact. Given the latter, the object gen- erally is to find the reaction rate dependency in terms of an intensive property of the system - number of reactive particles present, and of the energetics of the system - usually temperature. Chemical kinetics depend on a dem- onstration that reaction considerations alone control the phenomenological process under study. For these rea- sons, chemical kinetics are usually involved in homogeneous gaseous systems. Even in liquid homogeneous sys- tems earliness or lateness of reactant mixing rather than chemical kinetics may be controlling. Considerations of transport phenomena are involved in heterogeneous systems and often control the observable rate:an additional problem in such systems is to apportion the rate due to mass transfer - usually a linear process - and that due to reaction which may be linear or non-linear. Experimentally, conditions are often chosen so that only one consideration controls but this becomes more difficult where solid phases are involved. Kinetic modelling involves considerations of chemical kinetics, transport phenomena, and factors attributable to the physical environment in which the process takes place. The latter two considerations may be quite different as between experiment and plant. The kinetic model may be a mathematical representation of a conceptual mech- anistic model of the reaction. Alternatively, it may be an empirical relationship resulting from, for example, some curve fitting procedure applied to experimental data. The latter approach may be necessary where the system is particularly complicated.

Jan 1, 1975

By William V. Robinson

The Iron Ore Company of Canada mines, processes and ships crude iron ore, concentrate and pellets from the rich ore bodies of the Labrador Trough area in the extreme north-eastern part of Canada, some five hundred miles from Montreal (see figure 1). There are three main sites of activity. At Schefferville, approximately 12 million tons a year of crude ore (chiefly limonite) are mined, crushed, screened and shipped to Sept-Iles. At Labrador City, 40 million tons of specular hematite are mined annually for processing into 17 million tons of concentrate. Of this, 9 million tons are converted into pellets. All product 1s shipped to Sept-Iles. At Sept-Iles, on the north coast of the St. Lawrence, a six million ton per year concentrator and pellet plant process much of the Scheffervllle ore into high-grade pellets. Also at Sept-Iles are the company's administration offices stockpiles and shipping facilities. The Terminal facilities can berth and load a 250,000 ton bulk carrier at 19,000 tons per hour.

Jan 1, 1975

By B. F. Buie

For over 200 years meerschaum has been a significant item of trade between the Near East and countries to the west. Best-known for its use in making smoking pipes and cigar and cigarette holders, it is also used in making a variety of decorative and ornamental items. It is easily carved, and is given an attractive, lustrous finish by rubbing. No published specifications are known, but compact form, purity, uniform whiteness or light color, and uniform, porous texture appear to be requisites. Fig. la shows the appearance of a piece of crude meerschaum from Turkey; [Fig. lb a carved item; and Fig. lc, d, and e] show the fibrous and porous texture as revealed by the scanning electron microscope. Neither a major industrial mineral nor a precious stone, meerschaum nevertheless holds a record of long-and continuing-association with art and personal affairs of man. It is also a mineral to which modern methods of exploration and production probably could be profitably applied. An interesting account of the preparation and use of meerschaum in the early part of this century is given by Sterrett (1907). Geology and Mining Mineralogy Meerschaum is recognized now to be the compact variety of sepiolite, the claylike variety of which is one of the minerals included in the chapter on clays. The word "meerschaum," from the German meaning "sea foam," was in earlier times used synonymously with "sepiolite," a word of Greek origin suggestive of the resemblance of the compact variety-then the only variety known-to cuttlefish bone. At one time "meerschaum" was used as the commercial name, and "sepiolite" for the scientific name. However, to think of meerschaum as the name by which sepiolite is known commercially is no longer valid, in view of the recent emergence of the earthy variety as a competitor of bentonite and other clay materials. Present tendency is to restrict the term "meerschaum" to the compact variety, and to use the term "sepiolite" as a more general name to include both the compact and earthy varieties. This is the terminology followed in this publication.

Jan 1, 1975

By C. H. Elder

Coal degasification boreholes drilled from the surface have been success-fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3 coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By Michael Markels

The United States Environmental Protection Agency (EPA) is charged under the Federal Water Pollution Control Act Amendments of 1972 with establishing effluent limitations which must be achieved by point sources of discharge into the navigable water of the United States. Section 301 (b) of the Act requires the achievement by not later than July 1, 1977, of effluent limitations for point sources, other than publicly owned treatment works, which are based on the application of the best practicable control technology currently available as defined by the Administrator pursuant to Section 304(b) of the Act. Section 301(b) also requires the achievement by not later than July 1, 1983, of effluent limitations for point sources, other than publicly owned treatment works which are based on the application of the best available technology economically achievable which will result in reasonable further progress toward the national goal of eliminating the discharge of all pollutants, as determined in accordance with regulations issued by the Administrator pursuant to Section 304(b) to the Act. Section 306 of the Act requires the achievement by new sources of a Federal standard of performance providing for the control of the discharge of pollutants which reflects the greatest degree of effluent reduction which the Administrator determines to be achievable through the application of the best available demonstrated control technology, processes, operating methods, or other alternatives, including, where practicable, a standard permitting no discharge of pollutants.

Jan 1, 1975

By Vladimir Jindrich

This paper presents a history of a successful three year effort in locating a large, economic deposit of high purity limestone. The exploration program has been carried out by Ernest K. Lehmann & Associates, Inc., geological consultants, for Dravo Corporation, owner of the limestone property which is now under development. The permission of Mr. L. P. Struble, Jr, President of Dravo Lime Company, and Mr. M. W. Robinson, Director of Research and Development, to present this paper is gratefully acknowledged. The limestone property is on the Ohio River near Maysville in northern Kentucky, 60 miles east of Cincinnati (Fig. 1). The area lies at the eastern flank of the Cincinnati Arch, a regional structure where the Lower Paleozoic strata crop out below the adjacent younger sedimentary rocks of the Illinois and Apallachian basins. In general, the limestone formations of the Middle Ordovician High Bridge group offer the best potential for industrial limestone in Kentucky and adjacent parts of Ohio and Indiana. These formations are exposed along the axis of the Cincinnati Arch in central Kentucky. Toward the west, east and north, strata of the High Bridge group are progressively deeper, concealed beneath a succession of interbedded fossiliferous limestone and shale. The High Bridge group limestone formations are shallow-marine deposits largely of tidal flat, shallow lagoon and related environments. Principal lithologies include cryptocrystalline micritic limestone and crystalline dolomitic limestone to dolomite. Shale and bioclastic limestone are subordinate but the proportion of shale increases in the basal formations. Characteristic, is the occurrence of several thin beds of bentonite that serve as regional stratigraphic key horizons.

Jan 1, 1975

By C. M. McCulloch

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas con-tent of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and des orbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By Collins BJ

Basic principles of stack injection are outlined and supported by calculations of thermal, chemical and aerodynamic requirements of an ideal 4000 tpd furnace. Calculated results show that these requirements vary with conversion of FeO, and that best performance may be expected with XFeO = 1.0 for which calculated production is 6919 tpd and coke rate is only 211 kg/thm. Calculations are also presented for a cycled injection. Discussions show that stack injection is a good way of overcoming softening problems and meeting the demand for iron in a fluctuating demand situation when it exceeds the maximum capacity of a furnace.

Jan 1, 1975

By George A. Savanick

An experimental hydraulic jetting device intended to operate in a 16-in-diam borehole was designed, fabricated, and used to cut coal and simulated coal samples. This device consisted of two 0.107-in-diam nozzles that rotated in a plane perpendicuIar to a 50-inch length of high-pressure tubing. Experi¬ments were also conducted with stationary jets issuing from a single 0.142-in-diam nozzle. Numerous experiments were performed using systematic variations of jet parameters coupled with assessments of cutting rates. These Bureau of Mines tests showed that when operated at 4,000 psi pressure and a 40-gpm flow rate (1) the device can fragment coal up to a distance of 8 feet from the nozzle, (2) 4,000-psi jets cut more effectively than lower pressure jets with the same nozzle diameter, (3) stationary jets do not cut as effectively as moving jets, (4) interkerf breaking occurs when the kerf spacing is less than 2 inches, and (5) if the kerfs are spaced <1/2 inch, the jet is deflected and thereby reduces cutting effectiveness.

Jan 1, 1975

By J. K. Richmond

Early research on coal dust explosions by the Federal Bureau of Mines and in other countries is reviewed to examine the effect of a single inhibitor, rock dust, on the explosion limits of coal dust. The parameters studied in this research included coal dust fineness, volatile content, and type of initiation. This research resulted in appropriate safety regulations in the respective countries. Also reported are the results of recent research in the Experimental Mine of the Bureau of Mines to investigate in detail the limits of coal dust explosions; the research used three types of coal with rock dust added as the independent variable. New experimental techniques and new criteria for defining propagation/nonpropagation were applied to the experiments. Also, a limit explosion propagation model is proposed based on the assumption of rapid devolatilization of the coal particles, with the subsequent combustion of the evolved volatile products contributing primarily to the propagation of the explosions. The model assumes also that the resultant char acts mainly as an inert diluent similar to the rock dust. The model also suggests that the function of stronger initiation is mostly to lift more dust from the mine surfaces.

Jan 1, 1975

By O. P. Burghardt

Blast furnaces of high specific throughput capacities producing 10,000 tpd of pig iron or even more, require burden materials which, because of their chemical, physical and metallurgical properties, guarantee such high performances. Meanwhile, it should be generally accepted that for evaluating the quality of iron ore pellets, it is not sufficient to know the chemical analysis and the physical properties, i.e. grain size distribution, cold compression strength and abrasion of the fired pellets. It is indispensable to determine the metallurgical properties indicated by swelling, reduction-softening under load and reducibility, as well as grain disintegration in the low-temperature range in the beginning of reduction. By introducing new test methods, and in the face of the need to meet more strict requirements, pellet producers are being confronted with steadily increasing tasks and problems which require a deepening of our knowledge of the ways and means of making high-quality iron ore pellets.

Jan 1, 1975

By R. M. Ray

The Bureau of Mines evaluated five commercial badge-type carbon monoxide dosimeters. Color changes in the badge reagent indicated the presence of carbon, monoxide. Possible effects of ambient conditions on dosimeter response to CO during or after coal mine fires or explosions were studied. Temperature and humidity changes did not change dosimeter sensitivity to CO. Contaminant gases such as CO2, N02, S02, and H2S had effects that varied with brands of dosimeters ranging from no effect to increased sensitivity to CO. Dosimeters tested after 6 months of storage showed an increase in failure rate as high as 25 percent. Tests were conducted to determine the effects on dosimeter time-for-color change caused by observer&apos;s sight (colorblind); lighting, and coal dust on dosimeters. No significant effects were observed. Observer variance was the most pronounced factor observed in all tests.

Jan 1, 1975