Search Documents

By R. L. Armstrong, C. I. Godwin, V. M. Kruan

"The Scheelite Dome tungsten-bearing skarn property, central Yukon Territory, is in metasediments in contact with a quartz monzonite intrusion. Contact metamorphism to biotite-muscovite- andalusite hornfels and calc-silicate hornfels is superimposed on low-grade regionally metamorphosed rocks represented by quartz-mica pelitic schist and muscovite-biotite pelitic schist.Metasediments are likely Precambrian in age, even though Rb-Sr whole-rock analyses indicate an early Paleozoic age (511±41 Ma); this apparently too young radiometric age is due to partial loss of radiogenic strontium during regional metamorphism. The minimum age of the quartz monzonite intrusion is Cretaceous at 90.4±2.6 Ma (K-Ar on biotite) and its initial 87Sr/86Sr ratio is 0.7121. The high initial ratio of the intrusion is due to the addition of radiogenic strontium from the metasedimentary country rocks and perhaps an underlying older basement.Scheelite-pyrrhotite-chalcopyrite mineralization occurs in diopside-zoisite skarn pods within the calc-silicate hornfels near the quartz monzonite intrusion. The source for lithophile tungsten is probably the same as for the granitic magma, namely Precambrian sialic basement.IntroductionThe Scheelite Dome tungsten skarn property is within the Mc-Questen map-area (NTS: 115P/16),28 km northwest of Mayo, Y.T., at latitude 63°47' north and longitude 136°15' west. The property can be reached by helicopter or by four-wheel- drive vehicle from Mayo.This paper summarizes the geology of the Scheelite Dome property, which has been described in a general way by Little (1959) and Cathro (1969). Geological mapping and sampling were done by the first author (nee Steffler) during June 1979. Field work was supplemented with detailed work at the Department of Geological Sciences of The University of British Columbia during 1979 and 1980 (Steffler, 1980). Whole-rock chemical analyses were done by Cominco Ltd."

Jan 1, 1982

By Robert R. Turner

This paper discusses wet and dry primary autogenous and semi-autogenous grinding, including a description of the equipment and its mode of operation, testing and the scaling-up of test data. Lists of selected literature references are included.

Jan 1, 1982

By Robert J. Pokora

This report summarizes the work performed under USBM Contract No. J0100038, "Demonstration of Noise Control Techniques for the Crushing and Screening of Nonmetallic Minerals." The objectives of the program were to: a. Identify the prevalent sources of crushing and screening noise in portable and stationary plants b. Design retrofit noise control treatments for those sources c. Field test control treatments under actual operating conditions. A census of the nonmetallic industry was performed to determine the number and types of crushing and screening equipment. Based on the census, eight plants were selected and surveyed to assess the variety of noise sources, determine the worker noise exposure to those sources, and to identify possible constraints that had to be considered in designing and installing the retrofit controls. Three plants were selected from those surveyed and retrofit noise control treatments were designed, including: a. A primary crusher operator control booth b. Screen decks made of resilient cloth c. Screen feedbox impact pads d. Rubber feed plate for secondary crusher e. Rubber feed chute linings for secondary crusher f. Noise attenuating curtain for secondary crusher. A new primary crusher control booth was installed at one plant, and the operator noise levels were reduced from 97 dBA to 78 dBA. Screen noise at the two secondary crushing plants was reduced by 3 dBA to 7 dBA; crusher noise was reduced by 5 dBA at one of these two plants. Noise levels at normal outside operator and cleanup locations were reduced by 4 dBA to 7 dBA at one secondary plant, but operator/cleanup noise levels were not significantly reduced in the second plant due to rapid wear of installed materials. At one of the two secondary plants the retrofit noise control materials displayed excellent wear characteristics. The rapid wear of retrofit materials at the second plant was due to improper materials being supplied and changing circuit conditions.

Jan 1, 1982

By E. Concha

The concept of an Automated Continuous Explosive Excavation system (ACEE) for the underground mining applications of development drifting and room and pillar mining has been evaluated in comparison with conventional drill, blast and muck operations. The role and possible extent of application as this method was identified. The evaluation examined each element of existing and of proposed ACEE design concepts in a defined mine environment. Step by step procedures were developed to quantify the evaluation process where this appeared feasible. One conclusion drawn was that a system approach to ACEE design is not only feasible but attainable within the state of the art. Several preliminary design concepts were formulated and examined in order to determine what further research or development might be needed to realize them.

Jan 1, 1982

By L. A. Morely

The overall objective of the subject contract was to investigate the application, economic, and safety considerations of electrical-shock prevention techniques applied to surface and underground mines. Volume I of the four-volume final report starts by summarizing all research performed, and synopses of the three other report volumes are included. The balance of this volume concerns one major task of the contract, the protection of maintenance personnel. After specifying the scope of work for the task, electrical is defined, and needed ground-fault relay characteristics to prevent ventricular fibrillation are established. This is followed by an analysis of alternating-current systems, a comparison of these systems with respect to body currents, and the advantages and disadvantages of the various ground-fault protection techniques. An analysis of direct-current systems for off-track vehicles is then covered. These analyses form the basis for the research recommendations which along with suggestions for future research, conclude the report volume.

Jan 1, 1982

By Linneas W. Laage

Coal production from underground coal mines has been important to the development of the industrial economy of the United States. Environmental problems have developed from some abandoned operations. These problems include: mine and refuse pile drainage, subsidence, unsafe mine openings and to a lesser extent mine gases, slope stabilities, mine and refuse pile fires and abandoned equipment and structures. Field investigations in three eastern coal mining districts, two in Ohio and one in Illinois, were performed to document the mine closure procedures used and subsequent problems that developed. The purpose was to identify, evaluate, and rank the seriousness of these problems. Based upon this evaluation, the undesirable present day situations could have been avoided or at least minimized by varying certain mining practices or mine closure procedures. It was found that federal regulations address all of these problems during the pre mining, active mining and post mining phases except for abandoned equipment which is the least threatening problem category. Ideally current practice would prevent future problems. However, the extensive and complicated nature of the legislation, environment and mining practices will necessitate adjustments to the law. The investigator recommends the following: 1) Goal oriented legislation encouraging complete resource extraction, standardization and compilation of mining generated hydrological data, periodic review of the coal mining regulations, and improved communication and cooperation between coal interests, regulators and the public. 2) Permitting effluent limitations to accurately reflect natural conditions. 3) Solidly back filling shafts and individual assessment of sealing or capping requirements. 4) Installing shaft vent pipes into the fill material to intercept and vent methane.

Jan 1, 1982

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By Nick Chlumecky

INTRODUCTION Column-type supports are used to prevent roof falls in underground excavations. The first individual column supports were made from timber that was cut to fit the irregular heights of mine seams. Because the seam height of the material removed varied throughout the mine, timber posts generally could be used only once. During the I 920s, steel friction props began to appear in British and European mines, and, by the 1950s, thousands of these props were being used. However, the steel friction props were heavy, difficult to install, and difficult to recover. Furthermore, the friction props could not be preloaded, and their yielding behavior was rather erratic. In 1946, hydraulic props were introduced in En¬gland, and, within a few years, they replaced friction props throughout Europe. The first application of hy¬draulic props in the United States occurred in the 1950s, during early experiments with longwall mining. Modern technology and high-production mining procedures have combined to make the use of hydraulic props a very acceptable method of providing temporary heavy-duty support for production areas. In areas such as development headings, where only modest roof loads are expected, lighter-duty jackscrews, ratchet jacks, and light hydraulic props are used. ADVANTAGES OF HYDRAULIC SUPPORTS The acceptance of hydraulic supports has been wide¬spread during the past 25 years, proving their reliability and effectiveness in preventing roof falls. Some of the advantages provided by hydraulic supports are: 1) Individual hydraulic props can be installed within 30 sec, resulting in a minimum exposure of per¬sonnel and equipment to an unsupported roof. 2) Hydraulic props can be preloaded to more than 4.5 t (5.0 st), increasing the frictional resistance between the rock strata. Thus, the roof is kept tight, improving the behavior of the unsupported ground. 3) If gradual roof sagging or bottom heaving im¬poses an irresistible force, the hydraulic prop yields gradually and continues to support the ground. 4) The support capacities of the hydraulic props most widely used range between 10 and 20 t (11 and 22 st). Their support capacities are maintained during yielding to an irresistible force. 5) Hydraulic props can be recovered rapidly. Where no other supports are provided for the roof, as in pillar¬ing operations, the hydraulic props can be recovered by remote means. 6) The length of hydraulic props is readily adjust¬able allowing them to be reused in seams where roof height varies. 7) Studies of mining operations indicate that the use of hydraulic props increases both personnel safety and mine productivity. DESCRIPTION Figs. I and 2 illustrate typical hydraulic props used in mines in the United States. Fig. I illustrates a prop

Jan 1, 1982

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

By Hassell E. Hunter

The Wyoming Minerals - Conoco Crownpoint Joint Venture represents the first time that big hole drilling has been exclusively used to develop a privately financed mine. Three shafts, one ten feet in diameter and two six feet in diameter, have been successfully drilled to depths of 2243', 2188' and 2188' respectively and lined with hydrostatic designed steel casing. The largest shaft is to be used to as a development shaft to handle muck and water from enlargement and station excavation of the other two shafts. A reverse fluid air assist circulation system with potassium base mud was used during drilling. The mud was cleaned by settling in steel lined tanks with assistance from cyclone type sand separators. Deviation was monitored with wireline gyroscopic surveying instruments at 30 foot intervals. Horizontal departure did not exceed 16 inches off perpendicular. Casing was designed to withstand full hydrostatic pressures with a 1.5 safety factor for the large shaft and 1.25 safety factor for the two smaller shafts. All casing welds were x-rayed prior to lowering the casing into the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1982

By Robert L. Davidoff, Rodney D. Rosenkranz

In order to determine copper resource data and production costs for major market economy mines and deposits, the Bureau of Mines has performed detailed engineering and economic analyses on 271 of the world's most significant copper deposits. At the demonstrated resource level, copper potentially recoverable from these deposits is estimated to be 325 million metric tons, 180 million tons of which would be from Pacific Rim countries. Chile has the largest known copper resources of any country and accounts for nearly 45 percent of the copper avail- able from Pacific Rim countries. At $1.00 per pound, in January 1981 dollars, an estimated 80 million metric tons of copper are potentially economically recoverable from Pacific Rim deposits. At this same price, analyses indicate that these deposits could economically produce about 2 million metric tons of copper per year. Sensitivity analyses reveal that if operating costs were to decrease 25 percent, with copper at a price of $1.00 per pound, total copper economically recoverable from Pacific Rim countries could increase by about 10 percent; a 25 percent increase in operating costs could lower economically recoverable copper by 50 percent. Analyses also indicate that byproduct prices are important. If byproduct revenues increased 25 percent, at a copper price of $1.00 per pound, an additional 2 million metric tons of copper could be recovered; if byproduct revenues decrease 25 percent, about 5 million metric tons less of copper metal would be available. Since the January 1981 date of this study, inflation and decreases in copper and byproduct prices have greatly affected the profitability of the world copper industry. Many producing mines have curtailed or suspended production, and development of many non- producing deposits has been postponed.

Jan 1, 1982

By Tumilty JA, Douglas WD

With a view to characterising activated carbons with respect to their ability to adsorb gold from cyanide solutions, an attempt was made to establish correlations between the equilibrium capacity constant of the activated carbon for gold (k value) and five other parameters. These parameters were percentage ash content, iodine number, methylene blue value, surface area, and pH respectively. Twenty four different proprietary brand activated carbon products were examined, the correlations being established by means of linear regression analysis. It was shown that a significant correlation only existed between k and pH value. This was interpreted in terms of the presence of oxide complexes on the activated carbon surface. Further test specifications as developed at the Anglo American Research Laboratories are also outlined with a view to the selection of activated carbons suitable for use in' a carbon-in-pulp operation. Methods for assessing both the capacity and the kinetic response of carbons for gold adsorption are presented, while the measurement of attrition resistance, particle size distribution and moisture and solubles content is also outlined. The measurement of the capacity constant for gold adsorption together with attrition resistance are considered to be necessary in the initial selection of a suitable carbon.

Jan 1, 1982

By K. C. Carriere

INTRODUCTION The purpose of this section is to introduce the reader to the concepts of computer control of grinding circuits, and to flag some of the opportunities to be encountered, but without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with computer hardware and software, and in particular with the grinding process. The paper is organized into four parts: a general commentary of the need for computer control of grinding, a discussion of the process considerations involved, a more detailed elaboration on the current state of applicable computer technology, and a case study indicating one approach towards such a project. A brief installation survey and references for further reading are also given. This section will primarily deal with supervisory computer applications. Direct Digital Control and microprocessor systems are generally used as replacements for analog controls and thus are not considered in depth. Many configurations of grinding circuits exist, necessitating certain assumptions. Since many new concentrators use an open circuited SAG mill feeding a closed circuit ball mill, this configuration is used as a model although the principles stated can be extrapolated to any circuit. Motivation The use of computers for industrial control has been one of the dreams of control engineers and operators alike for many years. The concept of a plant running at optimal conditions with minimal operator involvement is very attractive from economic and technical standpoints. Accomplishment of this goal has been a long struggle, but today likelihood of success of such a project is very high, considering the reliability of modern hardware and the sophistication of available software. The primary motivation of any control system must be economic, i.e. it must pay for itself and make money for the owner, directly or indirectly. In grinding control the benefits which can be expected include: a) Higher through-put b) More uniform product in particle size, density and volumetric flog: c) Reduced operating costs including media consumption, power consumption and liner wear

Jan 1, 1982

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By R. O. Harma

Wet autogenous grinding is utilized in three iron ore concentrating plants operated by The Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping.

Jan 1, 1982

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By David Yob

INTRODUCTION This paper is intended to fulfill three major purposes. The first of these purposes is to narrate the improvements to the ventilation of Northeast Churchrock Mine and the subsequent reduction of the radiation levels. The second major objective is to pass on to persons unfamiliar with the ventilation of radon and radon daughter producing mines some of the most important characteristics of airborne radiation and the control thereof. The third objective is to describe the use of a computerized digital mine ventilation simulation. This description is not only of the usage, but also some of the important methods and techniques involved in the usage. This paper is not intended for the persons with extensive experience in these areas. However, to those persons who are just becoming involved with either ventilation of mines with airborne radiation problems or persons interested in computer simulation, this paper should be of some interest. It is the author's experience that most of the information on either computer simulation or airborne radiation control either assumes an extensive knowledge on the part of the reader, or does not address the direct application of the information contained in these articles. It is for that reason that this paper intends to concentrate on the actual application of the topics covered. INITIAL STATUS In the first quarter of 1980, the author and others became involved with the ventilation effort of the Northeast Churchrock Mine. At this time, this team began an investigation of the mine ventilation with the intent of reperforming a mine pressure survey. During the course of this investigation, it was determined that the ventilation system was inadequate. During this first quarter, the responsibility for ventilation of the mine was transferred to the author and his team. It was determined that the system that was in use was that of the single entry or haulage return type. In this type of system, there is very little direct control of the airflow, and it is not an effective type of ventilation for mines that experience problems due to airborne radiation. In a single entry, or haulage return, system there is no separate return system provided. In the system, as we found it, the only source of intake air to the ore level working areas was from the track level. This intake air was forced into the ore level, or stope level, via bulkhead fans installed on raises from the track. This air, after being used in the working areas, was then allowed to find its own way back to the exhausting vent holes. There was essentially no control of this air from the bulkhead fan discharge to the vent hole. The only control used was by the sizing of the fans on the raises. The main portion of this air used the haulage and access drifting for return. Due to the large horsepower used in these bulkhead fans and the large resistance both between the areas to the vent holes and inadequate intake ducting, the stope level pressure was higher than the track level. This pressure differential caused a severe recirculation between the stope level to the track level. This recirculation also caused a severe pre-contamination problem to the supposedly fresh intake air, making his air nearly unusable for working area ventilation. [ ] It was found at the time our ventilation effort began, that the radiation levels were high enough to make compliance with the four working-level month per year standard impossible. For this reason, we had to spend several months driving costly development drifts to implement a completely different type of ventilation system. Before describing the system that was implemented to solve the problems that were discovered during our initial investigation, some discussion of the characteristics of airborne radiation due to radon and radon daughters is needed. RADON CHARACTERISTICS AND RELATED TECHNIQUES One of the most notable characteristics of radiation contamination caused by radon and radon daughter decay is that once the contamination has entered the airstream, the radiation levels as measured in working levels will continue to rise without any further contamination. This radiation rise will eventually stop

Jan 1, 1982