Search Documents

By Bruce D. Hanson

The Bureau of Mines conducted a series of ignition tests with two types of conical bits (plumb bob and pencil) used on continuous mining machines, to determine their ignition potential at various bit speeds, cut depths, and wear conditions. The tests were conducted using single bits mounted on a 34-in-diam drum in a Bureau ignition test facility. The bits impacted blocks of Berea sandstone in a 6.5 pet methane atmosphere at various bit speeds and cut depths. In a new condition, the plumb bob bits were considerably more incendive than the pencil bits, causing ignitions in 32 of 35 tests at 60 rpm, compared with ignitiolls in 2 of 22 tests for the pencil bits. The results from new bit testing also show that reduction of bit tip velocity to 180 fpm does not eliminate ignition potential. When subjected to progressive wear, bits of both types were more incendive when they were locked in place, unable to rotate, than when they were free to rotate.

Jan 1, 1983

By Savidis G

The characteristics of 'Z' (Back-over run) and 'R' (Reverse) ventilation systems are dis- cussed in relation to their suitability for longwall mining. Experience in European mines has been described as a basis for comparison with Australian conditions. In assessing the merits of each ventilat- ion system, such factors as longwall layout (pillar design, number of headings and gateroad stability), the need for gas drainage and bleed- er systems, as well as the influence of seam dip have been considered relevant. The R system is generally applicable for single and two heading development in seams where gas emission is a less serious problem. In contrast, the lower extraction to development ratio of the Z system (which arises from using three or more heading layouts) is considered more favourable where high gas emission occurs. The Z system provides greater flexibility with respect to the provision of refreshing air at the tailgate end, access of men and materials, installation and retrieval of gas drainage systems and the ability to interchange main- gate and tailgate roadways in cases where roof strata loads are difficult to control, or where cpam in hac an influrnra

Jan 1, 1983

By Alan J. Solomon

The function of advertising is communication. Viewing the advertisements of mineral suppliers exposes the reader to a broad spectrum of purposes: announcements of new products, availability and supply, departmental services, company image, etc. It is the advertiser's hope that the message being conveyed is the same message being perceived by the viewer. To maximize this probability, the advertiser at least must carefully construct precise copy, identify the target audience and select the appropriate advertising medium. A truly successful and efficient ad, however, also must accurately reflect a product's life cycle, i.e., the rise and fall in demand for a product. Buggy whips and radio tubes are classic examples of items formerly in high demand. Industrial minerals are similarly affected by occurrences of product life cycles.

Jan 1, 1983

In recent years, wide consideration has had to be given to methods of improving the condition of the mine environment in many coal mines, and significant developments and changes have evolved. Thus even after substantial increases inòair flow rates at the working place (they have increased over three fold in the last generation), environmental conditions have arisen for which it has been necessary to introduce or consider: i) additional ameliorative measures, such as good housekeeping; ii) layout changes: such as Y or Z layouts; iii) homotropal ventilation; and iv) air conditioning. In certain countries, consideration has been given also to: v) additional payments reduced working times; vi) heat acclimatisation programmes; and vii) the use of cold or cooling suits At many hot and humid mines, the principal benefits from adopting (i), (ii) and (iii) have already been realised. At such mines,

Jan 1, 1983

By S. Jess Larsen

Modern technology has provided the world with many innovations to improve living standards, ease of job performance, efficiency, and managerial control. While not expected to compete with the computer revolution, Kerr-McGee Coal Corporation has found a way using laser technology to solve one of their haulage problems. Operating successful and profitable surface coal mine facilities in Wyoming's Powder River Basin require economies of scale, flexibility of operation, conscientious cost control, and ever-present innovative effort. Because haulage costs are the major source of expenditure in surface mining, Kerr-McGee recognized early the need for maximum haulage productivity and the economies of scale provided by large haulage trucks. Special conditions that exist in the Powder River Basin coal fields require consideration. The coal thickness (up to 100 feet and more) and varying depths of overburden dictate that a haulage unit with good gradability characteristics be used to avoid undesirable long ramps. Two and often three coal seams are encountered by most mines, which necessitates operating from several coal and parting faces simultaneously. This situation consumes much space, and to minimize the scope of problems, a coal haulage unit with good maneuverability and stability is needed. Finally, the low density of coal (±1500 pounds/loose cubic yard) demands a large volume capacity to utilize truck load carrying capability effectively. These conditions prompted Kerr-McGee to select unitized two-axle bottom dump trucks of the 160-170 ton size for primary coal haulage at its two Gillette-area mines. Use of 170-ton bottom dump trucks at the Clovis Point Mine handles most of the coal haulage, but the truck

Jan 1, 1983

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By Michael D. Loy

While the coal industry in general has been slow in accepting automation, the last few years have seen a myriad of products developed by the private sector. These packages run the full gamut from sophisticated geological information systems to line entry discounted cash flow analyses. This paper is an attempt to unravel the confusion that may exist about mining software. Discussions will highlight major differences between software products (such as block vs. grid models, prefeasibility programs vs. Monte Carlo analyses), briefly discuss known vendors, list known package features and touch on hardware requirements. The paper also focuses on the costs of automation (both software and hardware), possible trade-offs, advantages to in-house systems (vs. timesharing), a recommended review/selection process (including suggested RFP format), a test case procedure, when to bring in a consultant, and staffing considerations.

Jan 1, 1983

By R. J. Davidson, B. Strong

The piloting and eventual large-scale operation of fixed-bed carbon columns for the recovery of gold from plant effluents is described. A fixed-bed carbon pilot plant comprising three adsorption columns was used for the recovery of gold from clarified plant effluent at the Vaal Reefs Exploration and Mining Company (West Division). The effluent ,which contained 0,1 toO,S g/t of gold and less than 10 g/t of free cyanide, was adjusted to pH 8 prior to use. Daily acid treatment of the carbon circuit with 3 per cent hydrochloric acid was shown to have a most significant effect on increasing the gold adsorption. The acid treatment involved a plant downtime of only I to 2 minutes per day. High loadings of gold (up to 30 k g/t) and copper (up to 75 k g/t) were obtained on the leading column, while the gold recoveries averaged 98 per cent over 17 weeks of continuous operation. The subsequent elution of loaded carbon in a pilot elution column indicated the use of abnormally high amounts of the pretreatment reagent (caustic soda and cyanide) used in gold elution. This was attributed to the high loading of copper on the carbon. However, the elution of both the gold and the copper at 110°C with demineralized water as the eluant was satisfactory. In a similar large-scale operation, three fixed-bed carbon columns each containing 4,5 t of carbon were used to treat 80 to 120 t/h of plant effluent with a gold concentration of about 0,15 g/t. Gold loadings of 5 to 6 k g/t were obtained regularly, while the gold recovery averaged 97 per cent over a 12-month period. The capital cost of the plant was recovered in 2 to 3 months. The evidence presented strongly suggests that copper plays a significant role in the adsorption and elution of gold under the prescribed conditions, and in the subsequent precipitation of gold following acidification of the eluates. The formation of a highly insoluble gold-copper complex produced under acid conditions appears to explain many of the observations made in the investigation.

Jan 1, 1983

By Jerry Tien

Mine regulators are normally used for proper air distribution in underground mines. They are deliberately introduced resistance in the regulated airway, and by altering sizes, they can distribute specific air quantities to regulated splits and free splits (4, 5). The enactment of the Federal Coal Mine Health and Safety Act of 1969, the Federal Mine Safety and Health Amendments Act of 1977, and the regulations adopted by the Mining Enforcement and Safety Administration (now called the Mining Safety and Health ministration) prompted greater discussions of optimal mine regulator locations because of the Act's stringent ventilation requirements (2, 3). For example, by requiring the separation of the air used in the belt haulage entries from the intake and return airways, the regulations required the creation of a third type of airway---the neutral airway, as opposed to the intake and return airways, adding to the complexity of a mine's ventilation network. It is the intent of this report to show that panel regulators should be located in intake airways at the neck of a panel for a blowing fan system and in return airways at the neck of a panel for an exhausting fan system in order to achieve optimal air control. A computer simulation model is used to determine optimal mine regulator location.

Jan 1, 1983

By Richard N. Grigsby

INTRODUCTION The Chord property was acquired in 1975 from Roy Chord, an early prospector and miner of the area. He had staked numerous claims on the southern flank of the Black Hills in the early 19501s, and by the late 50’s, many small open pit and underground mines had been or were in operation. By the mid 1960's small tonnages of high-grade oxidized uranium ore had been mined from the property. Starting in 1975, Union Carbide conducted a series of exploration programs to determine the remaining economic potential. The previously mined areas were re-examined in order to define additional oxidized mineralization. Meanwhile, a wide-spaced drilling program was initiated to determine the potential for deeper unoxidized deposits. Through the exploration program of 1979, measured minable reserves in excess of two million pounds of contained uranium had been discovered. GEOLOGY The Edgemont District is located on the southern end of the Black Hills Uplift. A succession of pre-Cambrian to Cretaceous Formations is exposed within the core and across the flanks. The uranium host is the lower Cretaceous Inyan Kara Group which is divided into two formations, the Lakota and Fall River Formations (Figure 1). The basal Lakota Formation rests unconformably on the Jurassic Morrison Formation and consists of fluvial channel sandstones

Jan 1, 1983

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By G. Adel, J. Richard Lucas, C. Haycocks

This paper describes over sixteen computer programs developed at Virginia Polytechnic Institute and State University during the past twenty years to assist in the design of coal operations. Overall development concepts in the construction of the programs are outlined, commencing with those used in the exploration phase of mining and extending through economic analysis and into the design of specific engineering systems such as belt, rail and power networks, scheduling, rock mechanics problems and simulation of face systems. Summarized information is given for the use of the major programs including user restrictions, input data, typical output and industrial applications and case studies. Analysis has been made of the programs' applications by industry throughout the world. Such analysis is facilitating development of new programs as well as a refinement of existing ones. To date programs have been constructed in four categories: exploration, ground control, economic and simulation. Face production simulations are stochastic in nature and require the use of time study data obtained at sites underground. Future programming efforts currently under development are aimed at interactive programs for use with minicomputers and, where advantageous, with graphical displays.

Jan 1, 1983

By M. L. Jeremic, G. J. P Delaire

"The mechanical aspects of cable bolt failure are considered from the point of view of properties of grout and cable, as well as of the rock in which it is anchored. The results from recent investigations made in-situ as well as in the lab are combined and presented with reference to other work done in the area. An attempt is made to stimulate the thinking along these lines so as to initiate further research which may enhance the design of cable bolting as it applied to mining operations.IntroductionIn the past twelve year s systematic cable bolting has found application in many areas. In civil engineering rock anchors have been used to provide tension at the heel of a dam permitting the reduction of its cross section. They have been used in retaining walls to reduce construction time and costs by eliminating the need for struts and braces which complicate pouring the foundation walls. It is also possible to use rock anchors in providing reactions where tall buildings are subjected to uplift on one side due to wind forces. Cantilever bridges may be constructed by implementing rock anchors to provide anchorage requirements. Anchorage piles or dolphins or mooring ships have also been built using these. In the mining area rock anchors, commonly known as cable bolts because they are made of hoist cable may be implemented in the reinforcement of hanging walls or to retain rock slopes.In order to sustain de-pressurized ground where rock separation developed along the pressure arches, cable bolts were utilized at the Tsumeb Mine in South-West Africa and also at the Strathcona Mine in Sudbury, Ontario, In both places old degreased hoist ropes were installed in downholes from crosscuts above a given stope and then grouted without tensioning. Jeremic and Cassidy described the use of cable bolts to increase hanging wall stability and postpone fracturing, in addition to producing pre-support for improvement of stope back stability."

Jan 1, 1983

By N. Lecuyer

"During early 1980, pre-production work commenced at the ""Les Mines Gallen"" project, north of Noranda, Quebec. As a result of the acid mine water associated with this property, a major pre-production phase included the installation of a water treatment plant to render the water environmentally suitable.This paper emphasizes the planning, installation and operational factors of the treatment plant necessary to the success of the mining operations and the maintaining of a clean environment.Introduction,T he Gallen Project is a zinc, gold and silver open-pit mining operation approximately 10 kilometres north of Noranda, Quebec. This property has a long history, with initial diamond drilling done in the early 1930s and underground mining taking place between 1953 and 1962. This property was reactivated in 1980, with production scheduled a t a rate of 45,000 ton s per month.Included in the reactivation plans for the property was the installation of a water treatment plant to treat the acidic mine water.Plant DesignThe requirements for the Gallen water treatment plant were two-fold. Firstly, it was necessary to neutralize the acid water and secondly to produce a sludge containing metal hydroxides and sulphates which would be stable when stored, and a clarified overflow meeting governmental regulations to be discharged to the environment.The flow sheet (Fig. I) will explain the process in treatment of the acid water.Acid mine drainage is treated with lime to increase the pH to 9.50. Metals in solution are precipitated as metal hydroxides and the 504 as calcium sulphate. The precipitate slurry is then aerated to convert ferrous iron to ferric iron, which is more stable for storage and disposal.The precipitate is next flocculated with a polymer flocculant and settled in the thickener to produce a sulphate/Hydroxide sludge and a final effluent discharged to the environment."

Jan 1, 1983

By R. H. King

The Automatic Extraction System (AES) was designed and built under a US Department of Energy Contract by the National Mine Service Co. in cooperation with the Lee Engineering Division of Consolidation Coal Co. The Pennsylvania State University, Mining Engineering Section, was contracted as an independent auditor of the AES performance. The AES had a rotating cutter drum like a continuous mining machine. But two hydraulically powered roof supports, four roof-bolting drills, a dust scrubber, a ventilation fan and ducting in the roof supports, semi-automatic control, an extensible chain conveyor, and other innovations led to the distinction "extraction system" as opposed to "miner-bolter" or continuous mining" machine. After design and assembly, the AES was field tested experimentally in an underground coal mine. The in-mine performance audit was preceded by a computer simulation of the potential production for a later comparison with the actual tonnage mined by the AES. This paper describes the results of an in-mine trial and assesses the production potential of the AES.

Jan 1, 1983

By J. C. Agarwal

Do large-scale projects in mining and smelting start up and achieve expected capacity on schedule? In most cases not. Regardless of worldwide location, company know-how, or financial backing, unforeseen delays occur. A comprehensive CRA study for the World Bank shows that delays are the rule, not the exception, in most mining and smelting projects. When delays are not factored into analysis and planning, financial projections are, literally, not to be believed. Returns on investment will seldom achieve their targeted level because of startup delays. This paper reviews the results of our analysis of startup of new mines, mills, and smelters; provides a detailed discussion of why delays occur in the smelters and refineries; presents the cash flow implications of startup delays; and discusses preventive measures that should be taken to avoid financial shortfalls,

Jan 1, 1983

The purpose, basic data requirements and various analysis/modelling tools employed for geomechanical evaluation of mine-site conditions are overviewed. The impact and application of computer technology are dis- cussed. Broad guidelines and criteria are presented for establishment of a practical geomechanics data-base system to yield infor- mation suitable for mine design purposes. Future needs of the Australian mining in- dustry are examined.

Jan 1, 1983

By Richard E. Gray, William S. McCann, Robert C. Speck, Robert W. Bruhyn

Subsidence of the ground surface is the inevitable result of high recovery longwall and room and pillar coal mining operations. Up to now, U.S. research into this phenomenon has been concerned primarily with documenting the magnitude and extent of ground movements and prediction of the attendant ground strains through traditional ap¬proaches that have been developed in Europe and the United Kingdom. Preoccupation with ground strain prediction has, unfortunately, diverted attention from the more meaningful objective of predicting the severity of damage to structures at ground surface and the prob¬able cost to repair such damage. An attempt has been made to rectify this situation by reviewing in detail one hundred thirty four cases of subsidence damage to dwellings above active mines in western Pennsylvania, identifying the types of damage and the circumstances under which damage took place. The data reveal that damage to dwellings virtually always includes basements in addition to the readily apparent effects to the superstructure. In 90 percent of the subsidence cases, more than half the repair cost is associated with damage to subgrade components. A damage classi¬fication system has been devised that relates observed damage to severity and repair cost in a uniform manner for conditions in the Northern Appalachian Coal Field. Damage severity has been examined in the context of depth to the mine, the character of the near¬ surface overburden materials, mining type and other parameters.

Jan 1, 1983