Search Documents

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is ordinarily termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By Alexander May

The Bureau of Mines conducted studies to determine if phosphogypsum, a waste material from the processing of phosphate rock, contains hazardous toxic materials as defined by the Environmental Protection Agency (EPA) and whether leaching of these toxic materials and radium may occur. Samples of the phosphogypsum stockpiled material were evaluated using the EPA extraction procedure, atomic absorption, neutron activation, x-ray diffraction, and chemical and physical means. Radiological tests performed used both the germanium-lithium and emanation methods. The data show that the phosphogypsum stockpiles are not hazardous toxic waste as defined by EPA criteria. Trace elements and radium are not leached from the phosphogypsum stockpiles. Absorption of trace elements and radium by phosphogypsum is the major reason for their not being leached. The standard error of measurement of radium concentrations was 4.7 pCi/g.

Jan 1, 1983

By Cherie H. Tilley

The possibility of drilling oil wells from underground locations is not a new concept. It bas not been cost effective for the oil industry in the past and therefore disregarded. Today's state of the art in tunneling and shaft sinking greatly improves the potential for this type of oil field development scheme. This report presents a plan for providing a aeries of drilling bases and the design of the drilling location. The design minimizes the amount of excavation needed to develop the oil field and maximizes the use of rapid excavation techniques.

Jan 1, 1983

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company's computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By F. Cappel

Except in a few special cases, it is necessary for solid fuel direct reduction in rotary kilns that iron-bearing materials be charged with a minimum grainsize of approx. 5 mm. For fines not usable in such form, the combination of sintering - as agglomeration step - and direct reduction were investigated. During reduction of sinter in rotary kilns prevail dependencies on sinter quality and varying reaction parameters, owing to the use of different coals, which led to a definite statement as to what quality sinter must have and which coals can be used.

Jan 1, 1983

By T. Gelpe

A digital simulator of classification and grinding circuits is used to evaluate the performances of various flowsheets. For a given flowsheet configuration, unit processes dimensions and operating conditions, the simulator calculates the steady-state values of the process variables. A supervisory algorithm is implemented in the simulator to determine the conditions which meet the required criterion on operation, tonnage and product quality. Calculation illustrations are proposed for the design of wet and dry grinding circuits. The performances of various arrangements of cement clinker and sulphide ore grinding flowsheets are evaluated and discussed.

Jan 1, 1983

By J. A. Caldwell, G. E. Blight

The metropolitan area of the Witwatersrand has grown up around the Witwatersrand gold mines. Most of the mines have now been abandoned, but deposits of waste material remain and have been surrounded, and in some instances covered, by urban and industrial sprawl. This paper describes the development of geotechnical measures for the abatement of air and water pollution from abandoned gold-residue dams in the Witwatersrand area. The measures include the stabilization of the surfaces of the dams to prevent wind and water erosion, the terracing of slopes to minimize erosion, and the construction of catchment walls and dams. The measures were developed in terms of the set of guidelines for environmental protection adopted by the Chamber of Mines of South Africa in 1979.

Jan 1, 1983

By Bertrand D. L

Although investigations into treatment of Mt. Keast (a hill of tailing) began as early as 1940, it was not until the Imperial Smelting Furnace (I.S.F.) was installed at Cockle Creek by Sulphide Corporation that its treatment became eooncmically feasible. Early investigations and milling operations which began in mid-1976, with their developments are described. Metal recovery involves sulphide flotation, oxide flotation and gravity techniques.

Jan 1, 1983

By Dallas W. Davis

"Since May 1980, New Brunswick has called separate tenders for the right to explore and develop several potash prospects, as well as areas underlain by Alberta oil shale. These tender calls had in common the provision for a basic ad-valorem royalty, combined with sharing of cash flow after exceeding a 15-20% discontinued cash flow rate-of-return threshold. In the case of potash, the bidding variable was a share of cash flow, but for oil shale it was exploration expenditures committed, with the cash flow sharing to be negotiated at the time of application for a production lease. The Millstream potash occurrence, previously discovered by government drilling, received five bids (21.1% highest), the Dorchester ""grassroots area"" with four surmised drill targets apparently received no bids, and in the case of oil shale there were only two bids on the one block previously subjected to the most exploration.It is concluded that New Brunswick will not be successful in awarding the potash or oil shale rights in return for a comparable level of basic royalty and cash flow share as in the case of Millstream, unless it spends money in discovering prospects or sharing the exploration risk with companies. The approach is likely to work for oil shales only if current exploration proves the existence of much high-quality material or a definite trend of real increases in the price of oil is again established. Undoubtedly, it continues to be desirable to assure an on-going stable investment climate through award of potash and oil shale rights under terms which provide for a return that the public and future governments will consider fair. This could mean that some form or risk sharing with companies would be advisable."

Jan 1, 1983

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983

By Robert A. Robinson, Steven R. Thompson, Harvey W. Parker

The Mt. Baker Ridge Tunnel, under construction in Seattle, will be the world's largest-diameter soil tunnel with an inside diameter of 19.2 m (63 ft) and an effective outside diameter of about 24.4 m (80 ft). The five-lane highway tunnel will be constructed using a "stacked-drift" scheme in which an articulated or "flexible" tunnel lining consisting of 24 concrete-filled drifts is constructed to form a horizontal compression ring followed by removal of the soil core. Geotechnical factors, including variable strength hard fissured soils, high horizontal stresses, potentially unstable sands, and prior slope instabilities, significantly influenced the innovative design and construction approach.

Jan 1, 1983

By H. Robert Ensminger

The Belizean economy registered a modest real growth of 1.3% during 1981. The gross domestic product (GDP), based on current prim was $121 million' with an inflation-rate of 10%. The country received $19 million in economic aid during 1981. In early 1981, Belize'e four commercial banks raised the interest on deposits to 15% in an effort to curb capital outflow. During 1981, the financial situation deteriorated somewhat, particularly the balance of payments. For the year the total value of imports exceeded exports by almost $38 million, while the Government continued to maintain a fairly free trade policy. Import duties and term averaged about 8% on essential item and 40% on nonessential ones.

Jan 1, 1983

By Scott G. Britton

Today's coal mines are turning more and more to belt haulage as the key system to transport coal out of the mine. The advantages of using belt for both intermediate and main haulage are numerous. Belts are reliable high capacity haulage mediums that can be utilized at low operating costs. They are adaptable to rolls in the coal seam and can handle relatively steep grades. They are not noisy, operate with a minimum amount of labor, and are easily extended and retracted. Belts require the least power of any haulage medium, are easily controlled by push- buttons and interlocks, and present low fire and safety hazards. Belt haulage can also be the largest source of operational problems for mine management when not installed correctly. This chapter and Chap. 6 concentrate on proper installation of both the static and dynamic components of efficient belt haulage. This chapter looks at the static system component, composed of the belt drive, its installation and operation, as well as belt takeup and transfer point construction. These components do not change readily over the life of the installation, hence the term static system. Chap. 6 discusses the dynamic system of belt line construction, which includes belt splicing, breaking down and reanchoring the tailpiece, and extending the belt line, plus operational and maintenance items for belt operation. This chapter is divided into three major topics. The first is a general discussion covering the points necessary for designing an efficient haulage system; the second looks at installing belt drives, head rollers, and takeups, and the third discussion centers on installing efficient and effective transfer points along the haulage system. Each will address the design and construction issues facing the engineer or construction supervisor in charge of installing the system. Before looking at the static system, it may be useful to review some of the basic design factors and considerations of all belt haulage systems. The material usually carried on an underground belt is a mixture of raw coal and rock, commonly known as run-of-mine (ROM) coal. This mixture has certain material characteristics that guide the mining engineer to the final and proper belt selection. The characteristics looked at most frequently are: 1) Angle of Repose is the angle at which the material will freely make a pile. Most ROM coal averages a 35"-39" angle of repose. 2) Angle of Surcharge is the angle a pile will assume on a moving conveyor. This ranges from 5" to 15" less than the angle of repose in most materials. For ROM coals, 25" is the average angle of surcharge. 3) Flowability, which determines the maxi- mum cross-sectional area needed to carry any given material on a belt. It is measured by the angles of repose and surcharge of a material and also serves as an index of the safe incline angle for the belt line. These characteristics, plus practical engineering research and development work are defined by an organization called the Conveyor Equipment Manufacturers Association (CEMA) for most bulk materials. CEMA also provides a code for each classified material depending on the characteristics above and the subjective considerations of the average size to be encountered, the abrasiveness of the material, and any miscellaneous characteristics (oil resistive, corrosive, etc.) which may be important. For coal, CEMA (composed of member companies in-

Jan 1, 1983

By Craig Hartley

? A helper stands beside a continuous miner as the operator is at the controls. The operator means to push the stop button but hits the drum rotation start button by mistake. The drum begins to turn and the bits catch the helper's clothing. He is thrown violently to the ground and suffers multiple contusions. ? A farmer's wife helplessly watches her husband drawn into the claws of farm machinery while she frantically and unsucessfully searches for the control to stop the machine. ? A mechanic on the night shift replaces plugs in the lubrication systems of all three engines of an airliner following routine maintenance. In doing so', he fails to notice that "0" ring seals have not been mounted on the plugs. A few hours later, as the fully loaded airliner is cruising high over the ocean, oil pressure on one engine drops precipitously. The pilots quickly shut down the engine and turn for home. Almost immediately, the two remaining engines lose their oil and fail.

Jan 1, 1983

By PW Meisel

An hydraulic-powered reel system to minimize peak tension transients in shuttle car trailing cables has been theoretically designed and analyzed using a computer. A single spring-loaded take-up sheave stores or gives up cable to maintain tension within specified limits. Controls have been incorporated to shut down the vehicle before all cable is removed from the reel and to de-energize the cable in the event of a reel/cable jam. Full-scale hardware configuration drawings sufficient for manufacture of a test system have been completed.

Jan 1, 1983

By Stephen J. Crittenden

Deep gas and oil production has been substantially increased over prolonged periods through the use of sintered bauxite propping agents. Since its inception in 1976, over 170,000,000 pounds of high strength ceramic proppants have been employed. Recent field evaluations and economic analysis demonstrate the superiority of sintered bauxite proppant over quartz sand. This paper describes the development, application, field results, and product evolution of sintered bauxite.

Jan 1, 1983

By Danforth R. Hale, R. E. Blair

Minerals for electronic and optical uses divide easily into two sections: (1) quartz and (2) minerals other than quartz. Quartz Quartz, having a great usefulness discovered by the radio communication enthusiasts about 1918, has become a subject of amazingly expanded interest in the US over the past decade as a man-made mineral and a multimillion dollar crystal-growing business. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engineering industry when it is remembered that quartz crystals have long been an important commercial mineral, and that the raw material for "cultured quartz"-that is to say, quartz crystals grown through the ingenuity of man-is still natural quartz. Nearly all the natural crystals come from Brazil. The larger pieces which meet rigorous standards of quality are used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments are used for vitreous silica. The need for high quality material in quantity led to US government-sponsored research programs in the 1940s that have resulted in the factory growing of beautiful crystals of prescribed shape, size, and quality. The development of the cultured quartz crystal is typical of man's success in adapting the product of the mine to increasingly sophisticated uses. A remarkable achievement perhaps, but foreshadowed by experiments in 1908 by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modern radio equipment is most often controlled as to frequency by the presence in the circuit of a separately added "crystal"-the 1918 discovery responsible for the existence and growth of the quartz industry. The "crystal" is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964; Mason, 1964). Quartz belongs to that class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the "piezoelectric effect," which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other, positively charged. When the plate is released from the stress quickly, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By coating the two surfaces thinly with metal and attaching flexible wires, these charges may be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the "converse piezoelectric effect" occurs -the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation of the plate and is keyed to this oscillation. By controlling the thickness of the plate its mechanical vibration frequency can be varied through a wide range. One type of quartz plate, called the AT-cut, having a precisely defined orientation with respect to the crystallographic axes of the crystal, vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. There are at least 17 other orientations which have been studied, some of

Jan 1, 1983

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"In January 1974, the Minerals Division of Canadian Occidental Petroleum Ltd. made the strategic decision to add uranium to its active exploration commodities and through compilation studies selected northern Saskatchewan as the most attractive and cost-effective exploration area in Canada. In August 1974, 100 sq. miles were staked adjacent to Gulf Minerals' Rabbit Lake deposit and east of the Esso Minerals Midwest boulder train. Initial exploration was based on geologic models of the Rabbit Lake deposit.In the summer of 1975, surface surveys delineated radon anomalies which were drilled that winter and found to overlie anomalous concentrations of uranium in the regolith which forms the upper unit of the crystalline basement. Within the crystalline basement, one hole intersected graphite and pyrite with anomalous nickel-cobalt-arsenic. Geochemical and radiometric surveys followed in the summer of 1976. Drilling in the winter of 1977 intersected several zones of graphite and also anomalous, but uneconomic, uranium abundances. Also in 1977, Dahlkamp and Tan (1977) described the coincidence of graphite and uranium at Key Lake and ground EM surveys on CanadianOxy claims detected graphite conductors beneath 250 ft of Athabasca sandstone. Inco Limited joined the project in April 1977 as a 50% partner. The project area was then surveyed using the airborne INPUT EM method, which detected 84 miles of conductors, with associated graphitic metasediments. On the ground these were located with MaxMin surveys, and follow-up drilling located the ""Tent"" Lake uranium zone.In 1978, the Midwest and Dawn Lake discoveries were announced, 7 miles and 2 miles west of the Joint Venture (J.V.) claims; and, in part for this reason, the 1979 winter drilling was concentrated on the deeper west side of the property. Exploration hole 102-79 intersected altered and uraniferous rocks, but stepout holes were barren. Drill hole 153-79 tested an under-snow three-station radon anomaly east of hole 102-79 and intersected 33 feet of 7.51 % U3O8, confirming the disco very of the McClean North zone. The geophysical grid of the McClean North conductor system was extended and detailed a strong, continous conductor to the south, called McClean South. This was drilled in January 1980and hole 1004-80intersected 22 feet of 2.95% U3O8."

Jan 1, 1983

By William B. Thayer, James H. Meinholz

The Milwaukee Metropolitan Sewerage District (MMSD) has been working since mid-1977 on a fast track to meet a court-imposed schedule to rehabilitate a large wastewater collection and treatment system at an estimated cost of $1.7 billion. Because of glaciation, the Milwaukee area has an extremely complex geologic environment. The rock surface ranges from outcroppings in the northern and western parts of the area to 76 m (250 ft) below the surface at the mouth of the Milwaukee and Menomonee Rivers. Bedrock beneath the glacial mantle is a thick sequence of early to middle Paleozoic sedimentary rock. To cope with the many complexities of this large public works project, a Program Management Office (PMO) concept has been employed. A Geotechnical Engineering Group was established within the PMO to provide a continuous , unified approach to geotechnical engineering and full disclosure of all geotechnical information in the construction contract documents. It provides qeotechnical engineering to design and construction, develops and maintains a qeotechnical data base, and participates on the claims resource team.

Jan 1, 1983

By Visnovsky

The computing needs of a mine planning office vary greatly depending on the staff available and the nature of the work undertaken. Some offices work acceptably with few aids apart from hand held calculators while others use mainframe computers with associated data bases and sophisticated mine planning software. Not every mine planning office requires the big system approach but all can benefit from the intelligent use of small computers. There is virtually no limit to the design problems which can be solved using modern desktop computers. The simple language required encourages engineers to work interactively to facilitate both large and small computations. However a limit does exist in the speed and ease with which solutions can be obtained. The important ingredients for the successful application of such machines are a little computing knowledge, a flexible machine, and an engineer who really understands the mining problems confronting him. If these are available it is possible for the engineer to tailor the program to the task at hand and efficiently achieve the required result.

Jan 1, 1983