Search Documents

By Heinz Distelmeier

The New Austrian Tunneling Method was, as is well known, developed from conventional rock tunnelling. In Germany about 10 years ago the NATM began to be applied to partially stable soils by incorporated excavation and support methods to allow its use with these soils. The advantages of this tunnelling technique - adaptability, ecomomy, and quality have resulted in its widespread usage. Today, about 85 % of all mined tunnels in Germany are produced with this technology. This rapid development has resulted in about 40 companies operating within a geographical area about the same size as the state of Illinois that are capable of utilizing the NATM. In most cases German contract/award procedures allow the contractor to develop alternate design and plans. As a result of this flexibility and intense competition, safety factors have been gradually reduced to the lower limit of what could be regarded as demonstrably safe, and the utilization of the NATM has expanded to include higher risk conditions, namely * excavating larger cross sections. * working with less overburden. * work undertaken under less stable soil conditions.

Jan 1, 1983

By J. V. Happ

The investigation reported in this paper was prompted by the belief that vacuum processing of copper mattes could provide significant advancement to present-day copper smelting and converting technology. Specifically, vacuum distillation of copper mattes in a unit such as the R.H. vessel used in vacuum degassing of steel, can lead to improvements in: converter flue-gas-cleaning system, purity of acid (or liquid SO2), aisle hygiene, purity of electrorefined copper and smelter flexibility. In the study conducted, removal of Volatile impurities (arsenic, antimony, bismuth, lead and zinc) from liquid mattes, by vacuum distillation in a laboratory-scale equipment was performed. The conditions investigated covered a temperature range of 1123-1223K, absolute pressure of 6.5-0.5kPa (50 - 3 mm Hg) and with bleed gas consisting either of pure oxygen or argon. Six matte samples (four U.S. and two foreign) were tested. Under the "best" conditions arsenic and antimony were reduced to << 0.01% in the product matte. The removal of bismuth, lead and zinc was variable and appeared to be influenced by the matte composition of the sample. As might be expected, the rates of distillation of the various species were increased at higher temperatures and lower absolute pressures. The influence of a small flow rate of gas (02 or Ar) over the melt did not have a signifi¬cant influence on the extent of impurity removal. The magnetite content of the matte was reduced by up to 30% during vacuum treatment and was favored by a low partial pressure of oxygen over the melt. Substantial amounts of sulfur were also evaporated and an, overall increase in copper grade of the matte was realized. The paper concludes with an evaluation of industrial aspects of the process as applied to conventional smelters.

Jan 1, 1983

By J. S. Li, J. C. Edwards

A prediction is made of the airflow at the Bureau of Mines Lake Lynn Laboratory with a ventilation computer program that accounts for fan-driven forced ventilation and temperature-induced natural ventilation. There was substantial agreement between measured and predicted airflow rates. The capability of the program is demonstrated as a planning aid for ventilation under emergency conditions in a multilevel coal mine. Smoke spread in a multilevel mine is analyzed following the occurrence of two events, the failure of the main exhaust fan and the development of a fuel-rich fire in a passageway.

Jan 1, 1983

By David B. Crouch

Wastes in various forms have always been a part of mining, and management of mine waste has evolved from the early days of "push it over the side and down the creek" to today&apos;s highly engineered waste facilities. Changes have been brought about not only by technological advances in the ?3M?s? - mining, milling, and metallurgy - but also by environmental awareness and changing social values that have been manifested in an ever-growing maze of regulations. This is a dynamic era, and the debate goes on. So it is that planners have to anticipate permit and regulatory requirements in the site-selection process along with the traditional criteria. The McLaughlin gold project is an example of how one company, Homestake, has met this planning challenge. In August of 1980, Homestake Mining Company announced a major gold discovery in northern California known as the McLaughlin Project. The property is approximately 80 air miles northeast of San Francisco near the junction of Lake, Napa, and Yolo Counties. This is an area where mercury has been mined off and on for over 100 years; gold has never been mined in the area. The gold is microscopic and finely dispersed in a complex geologic setting. Reserves are estimated at approximately 20 million tons at a grade of approximately 0.16 ounces per ton.

Jan 1, 1983

By Robert D. Norris

Heap leaching provides a method of economically recovering gold from low grade ores with low capital and reasonable operating costs. As with conventional methods, alkaline cyanide solutions are used for leaching. Since gold (and silver) is (are) present as the native metals, oxygen (as air) is required to oxidatively complex the metals with the cyanide. Oxygen depletion can readily occur adversely affecting recovery. The addition of low levels of hydrogen peroxide during leaching can lead to significant increases in both rate of recovery and total recovery. This process allows for the use of shorter pad times or deeper heaps and increases the gold (silver) concentration to the recovery circuit and thus can reduce cyanide losses by virtue of permitting the use of less total leach solution per ton of ore processed.

Jan 1, 1983

By D. C. Rance

"The Quintette Coal Limited property is located in the northeast coal area of British Columbia.A basic agreement with the Japanese steel industry was executed on January 27, 1981 for the sale of 69.5 million tonnes of Quintette metallurgical coal over a 14.5-year period. This contract period can be extended by five years by mutual agreement. Sale agreements have also been signed for the sale of 19.4 million tonnes of oxidized coal over a 15-year period.Work started on site development in the late summer of 1981, and at present, two of the four eventual pits-the McConkey and Frame-are under development.The pits are currently in a prestripping phase. These pits are notable for the stripping volumes that have to be removed from relatively small pit areas. In order to provide for the required detailed rapid short-range planning of these pits, engineering will be computerized, as will the truck dispatch system.The mining area lies 21.1 km from the plant site by road and the transport of raw coal to the plant is by means of a high-speed conveyor system which has a total length of 13.4 km with a vertical drop of 740 m.The surface plant facility was designed on a modularized basis to facilitate maintenance, and is designed to enable the use of gravity f low of raw coal and heavy media in the plant to minimize the use of pumps.The construction of the plant and mine site facilities is ongoing, and the first coal production is scheduled for early December 1983.IntroductionQuintett e Coal Limited is a Canadian company incorporated in the province of British Columbia in 1971. Denison Mine s Limited is the manager of Quintette&apos;s activities. Equity in Quintette Coal Limited is held by several shareholders, with interests as follows: Denison Mines Limited, 50%; Charbonnages de France International S.A., 12%; and Japanese interest, 38%."

Jan 1, 1983

By B. W. Madsen

Bureau of Mines research to recover arsenic from mining industry waste material and process streams is reported. Batch and column approaches were investigated for adsorbing arsenic from acid leach solutions and ion-exchange eluate solutions with hydrated titanium dioxide granules. A method for producing hydrated titanium dioxide granules was devised to provide material suitable for use in a packed adsorption tower. Selective adsorption of arsenic from acidic leach solutions was achieved. The loading capacity of arsenic on the granules was 14 wt-pct when synthetic solutions were used, but lower when actual leach solutions were used. Other elements in the leach solution were Zn, Cd, and In. The granules were used in an attempt to lower the arsenic content in a solution containing 0.95 g/l W and 0.027 g/l As from a process devised by the Bureau of Mines to treat Searles Lake brine. The arsenic content was lowered to less than 0.001 g/l, but unacceptable amounts of tungsten also were adsorbed by the granules. Adsorbed tungsten was partially stripped with pH 11.5 NaOH, and both tungsten and arsenic were completely stripped with 5M NaOH solution. Repeated loading and stripping of the granules had no effect on the loading capacity for arsenic.

Jan 1, 1983

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

By J. F. Lazenby, W. F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test method&apos;s used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1983

By Jun-Yan Chen

Ground control problems in sublevel caving become evident as the rock pressure increases with depth. Recently, a finite element analysis of the stability problem of the sublevel caving method was completed by the author. This paper summarizes the results of stress analysis in sublevel extraction drifts under different field stress conditions by using linear elastic and nonlinear elastic-plastic finite element modeling techniques. A critical stress concentration will occur in the uppermost sublevel drifts beneath the caved area or blasted ore area. During the blasting and drawing cycle, a tensile and shear failure condition could develop in the center extraction drift when it would be mined last. Under a high horizontal stress field condition, almost all tensile stress in the back of the extraction drifts will be eliminated and only slight yield can be seen in the floor of the extraction drifts. Compared to the cases under the stress field where vertical stress is the dominant factor, the total yielding zone will be greatly reduced because of an in- creasing horizontal stress field with depth. However, it is predicted that the center of each ore column side will experience excessive shear stress that probably will result in ore failure. The two major conclusions drawn from this study to improve the overall stability of sublevel caving are: (1) the drift width must be carefully controlled and an appropriate stoping sequence selected; and (2) the sublevel caving method can be used in deep min

Jan 1, 1983

By David Harrison

Exxon Minerals Company uses geostatistical techniques for ore resource evaluation of its mineral projects. These techniques provide the most reliable estimates of recoverable tonnage and grade and uniform and realistic confidence limits. A schema has been developed which categorizes the company&apos;s successive evaluation phases. Clear separation is intended between geostatistical estimates and other factors in project evaluation such as mining, metallurgy, and economics. Company management seeks consistent and reliable estimates for investment decision-making and to meet growing demands for disclosure of mineral assets.

Jan 1, 1983

By Eugene Baker, Joseph Cervik, Albert Sainato

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the United States is limited to a few plow operations in the Pocahontas No. 3 Coalbed. This Bureau of Mines report describes the technology for infusing water in to a longwall panel and reports the results of a recent demonstration in the Lower Sunnyside Coalbed that achieved dust reductions averaging 58 pct. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 500 ft/min (2.5 m/s) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23-pct reduction in operating costs when coal production is increased by changing from unidirectional mining to bidirectional mining with water infusion.

Jan 1, 1983

By C. A. Sobotowski, J. Eagan

Computer programs applicable to coal mining have been available for some time, especially in the academic sector. However, the computer has not routinely been applied to actual mining operations. This paper discusses how a computer system was set up as an important tool in mining design and decision making. The project was completed within the allotted timeframe of two months by taking advantage of existing technology. Key points include the selection of programs to meet the specified needs of the project, conversion of the programs to be compatible with a computer of a different manufacture, simplification of the data entry process, development of procedures for using these programs, and an explanation of how the reports generated from the programs were used for mine planning and decision making.

Jan 1, 1983

The first introduction of automatic control systems for flotation occurred about fifteen years ago. The early control work coincided with the introduction of on-line assaying using XRF techniques. This OSA availability, coupled with the emergence of small digital computers suitable for process control in the late 1960-s, meant that the necessary process information and control hardware existed for flotation control experiments. A period of intensive research related to flotation control. ensued. A great deal of effort was devoted to the development of mathematical models of flotation. Plant experimentation sought to understand the effects of a range of flotation variables on the process. Finally, control loops were proposed and plant tested. An evolutionary pattern emerges when the range of flotation control installations is examined. The earliest systems had as objectives process stabilisation using reagent control. There were also some early attempts at flotation optimisation procedures, again using reagent variation. Current work is still associated with the same objectives. One of the difficulties with flotation control has been to recognise and define clear and precise control objectives. More emphasis is now placed on cleaner control which has the advantage that the objectives are usually well defined. A number of flotation control systems which cover a range of control system types is discussed. Based on this accumulated experience,a list of good and bad practice in flotation control is Proposed.

Jan 1, 1983

By John J. Van den Broek

As the established tailings disposal techniques do not meet the requirements of today, alternative methods of disposal are explored. McIntyre Mines Ltd., Coal Div. found a solution in the construction and operation of a tailings dewatering plant. The solids are recovered from the tailings slurry by means of mechanical dewatering equipment and are then dried in a unique drying system to provide an excellent thermal fuel for a power generating station.

Jan 1, 1983

By T. V. Subrahmanyam, A. P. Rao

The adsorption behavior of chalcopyrite has been studied at different xanthate concentrations and flow rates in a column apparatus with potassium ethyl xanthate as the collector. Based upon the experiment results an equation of the type: 1/F = K3 + m3C + k2/t.Cm2.fm1 is proposed to account for the experimental data. Among copper minerals an early study on chalcocite by Gaudin and Schuman (Taggart, 1951) is well known for its research on the kinetics of the reaction by conventional method of mass balance between the products of reaction and xanthate consumed. The results were interpreted by the concept of ion exchange adsorption. Szeglowski (1977) conducted measurements on the adsorption of potassium ethyl xanthate on copper polarized to various potentials, the adsorption being measured by radio-tracer techniques. The adsorption in the range -1800 to 700 mv was found to be a reversible physical adsorption. The potential range in which the primary electrode process could lead to surface coverage with a minimum number of product layers was evaluated. The adsorption density of xanthate on sulfide surface was found to be related to the concentration of xanthate in solution and concentration of depressants as: [ ]

Jan 1, 1983

By James P. Bennett

To identify construction materials for emerging technology in chemical and metallurgical processes, the Bureau of Mines investigated the acid resistance of ceramic materials. Eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a five-claybonded silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed for 110 days to 20 wt pct HCl at 50°, 70°, and 90° C and to 30 wt pct HCl at 70° C. Statistically significant changes in cold crushing strength, volume, and weight were generally small or not detected. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. The carbon brick sample had the best acid resistant properties with a maximum total leached ion weight loss of 0.004 wt pct. The silicon carbide, the silica, and one of the fire clay bricks also had excellent acid-resistant properties.

Jan 1, 1983

By McMahon DW

The major components of a mineral reserve estimate for project development purposes are described with respect to sampling, geology, estimation methods, mining factors, metallurgical factors, environmental factors, financial and other factors. Each of these components impact to varying degrees on the recoverable metal or product of a new mining project. The evaluation of a project is a complex process involving the best the profession can provide in terms of geological understanding, engineering ingenuity, metallurgical skills and financial evaluation.

Jan 1, 1983

By M. R. Baren

Unpublished results obtained by Baren on thermodynamic properties of sulfur in liquid Fe. Co. Ni. Fe-Co. Fe-Ni. and Co-Ni are reevaluated. correlated. and interpreted on the basis of recent developments in thermodynamics of alloys:. Existing reliable data are reviewed and compared with the? present results. Sulfur obeys Henry&apos;s law up to 0.04 mol fraction. and in this range the standard Gibbs energy of solution of sulfur is expressed as a linear function of temperature for each pure metal. The activity coefficient of sulfur in each binary metal solvent 1s correlated with the composition of alloy.

Jan 1, 1983

The control of industrial grinding circuits in Australian concentrators has been practised for many years in one form or another. Some have established simple feedback loops in areas such as fine ore bin feeders (tonnage control), mill pump sump levels (flow control) and water additions (density control). There are also some sophisticated systems which infer circuit product size using complex measurements of mass flaws and water additions in the circuit and attempts are made to control those flaws to produce a constant circuit product size. The inferred size method in Australian concentrators has become firmly entrenched in the last ten years and control techniques involving the use of direct size measurements with reliable on-stream sizers have been Ignored.

Jan 1, 1983