Search Documents

By Kittitep Fuenkajorn

Ring tension tests, permeability tests, and microscopic fracture studies have been performed to investigate the damaged zone induced by drilling (diamond, percussion, and rotary) in the borehole walls. Specimens are drilled with three different hole sizes (38, 76 and 102 mm diameter) in Pomona basalt and Grande basaltic andesite. The thickness of the damaged zone ranges from 0.0 to 1.7 mm. A larger drill bit induces more wall damage than a smaller one. Different drilling techniques show different damage characteristics (intensity and distribution). Damage characteristics are governed not only by drilling parameters (bit size, weight on bit, rotational speed, diamond radius, and energy), but also by properties of the rock. The weaker rock tends to show more intense damage than does the stronger one. Cracks within grains or cleavage fractures are predominant in coarse grained rock (larger than 0.5 mm grain size) while intergranular cracks are predominant in fine grained rock (smaller than 0.01 mm grain size). The influence of the damaged zone on the permeability of the rock around the hole is investigated by permeability tests.

Jan 1, 1984

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites. The process consists of four major steps: (1) reduction roast, (2) ammoniacal leach, (3) solvent extraction, and (4) electrowinning. Several solid-liquid separation steps are required that affect the economics of the overall pro-cess. In this study, two techniques for solid-liquid separation, centrifugation and thickening, were investigated. This report presents the results of (1) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and (2) an economic study of the two techniques, based on the requirements of a commercial-size (5,OOO-tpd) laterite processing plant. Sizing and other equipment-related recommendations, based on data from the Bureau's studies, were obtained from commercial manufacturers. The costs of thickening and centrifugation, including all the unit operations affected, were determined by the Bureau's process evaluation group. The total operating costs ~or separation using the two techniques (including depreciation on the capital cost of equipment) were found to be quite close: $17.26 per ton of laterite for centrifugation and $18.15 per ton of laterite for thickening. For centrifugal separation, the greatest cost was found to be the initial capital cost for the separation equipment; using thickeners, the greatest cost was for re-agent recovery.

Jan 1, 1984

The paper describes the reasons for the development and for the selection of systems which were finally adopted; further estima- tion and design engineering problems, as well as experience with large screens in operation. Advantages, disadvantages and the final li- mits of screen dimensions are indicated.

Jan 1, 1984

The ER&S Company operates a copper sinter plant, blast furnace and converter smelting complex at Port Kembla. Eighty percent of the smelter feed is dirty copper concentrates that contain some lead and zinc. The remaining twenty percent of the smelter feed is copper bearing secondary materials, some of which contain lead, zinc and tin. A predominately lead/zinc fume is produced during the smelting and converting of this feed mix. The composition and tonnage of fume produced at Port Kembla has varied over the years as the smelter feed sources have changed. The economic processing of the fume has always been dependent on the value of the metals contained in the fume and on the fume composition. Both pyrometallurgical and hydrometallurgical methods have been used to treat the fume for the recovery of some or all of the following metals - lead, zinc, tin, copper, cadmium, silver and bismuth. A detailed description of the treatment methods that have been investigated and used to process ER&S fume is given.

Jan 1, 1984

Crossroads for Students Students in their matriculation year, whatever their background, have reached a crossroads in their lives: behind them lie the relatively carefree years of childhood; ahead lies the whole of their working lives. Whether those working lives will be rewarding and interesting depends to considerable extent on whether they get 'a good matric' and carry on to some form of further education. IPMI awards 1985 Nominations for the 1985 Awards are now being accepted by the Awards Committee of the International Precious Metals Institute. THE DISTINGUISHED ACHIEVEMENT AWARD was established to recognize important career contributions to the advancement of precious metals, be it technological, economic, or business.

Jan 1, 1984

By L. Moussoulos

Pyrite concentrates produced at the Olympias mines, Northern Greece, show an unusually high gold and silver content (16-20 and 25-40 ppm respectively), associated with the presence of arsenopyrite; their high As content (5-8%) has hindered their utilization so far. In the present paper a simple and environmentally safe method that permits their complete utilization for the production of SO2 gas, As203, and the recovery of Au and Ag is described. According to this method, the pyrites are subjected to a single-stage oxidizing roasting in a fluid bed reactor. The precious metals, and approximately 45% of the contained As, remain with the cinders, while the rest of the As is removed with the SO2 - bearing gases and can be recovered by suitable treatment. The gases, after further cleaning, can be utilized for the production of sulfuric acid.

Jan 1, 1984

By Roger N. Miller

Talc mining in Vermont has in recent years undergone a progressive change in mining methods and in mining equipment. Underground mines have been phased out except in special circum- stances, and continuous mining machines (CMM?s) have replaced conventional drill/blast mining systems. Talc mining in Vermont began in the late 1800?s, and has continued without interruption to date. Beneficiation (flotation) has been applied since the early 1930?s, and has provided special products for toiletries and other markets. At the present time, there are two active companies that have evolved from the cumulative absorption of nearly ten smaller operations.

Jan 1, 1984

By Hadyn W. J. Wren

The practical experience obtained from designing and commissioning of fully controlled coal preparation plants, using centralised mini computers is discussed. The importance of defining a workable operating philosophy is highlighted with particular reference to the problems associated with trying to achieve a total 'hands off' concept. These experiences with a centralised computer controlled system have led to a deeper understanding of the interaction between the operation and the control system and the role of local control and management information within the overall control philosophy of a highly automated process plant. The utilisation of an extensive fully distributed microprocessor control system with over 6500 digital and analogue signals split into six autonomous areas with a supervisory system to provide operator interface is described. The important aspects of project definition and design needs are outlined with particular regard for achieving maximum efficiency with minimum complexity. Views of future trends are offered, based on the experience of both centralised computer and distributed processor systems.

Jan 1, 1984

By Hassan El-Shall

Treatment of plant effluent including waste water and associated soluble and insoluble substances, is of a primary concern of many process industries including mineral processing operations. The major objective of such treatment is the removal of such impurities which can interfere with the process through the use of recycled water, and/or to comply with environmental ordinances. For example, Ramirez and Clements (1978) state that molybdenum contents in the range of 19 mg/1 eventually poison ion exchange resigns used for the extraction of uranium. In addition, recent restrictions by the EPA on molybdenum discharge values for mining waste water necessitate removal of this metal to (0.5-1.0 mg/1).

Jan 1, 1984

By B. N. Thompson

Main industrial minerals produced in New Zealand are nonmetallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. Other minerals, some with minor production, include diatomite, feldspar, magnesite, sulfur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example, clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of late Cenozoic acidic volcanic rocks.

Jan 1, 1984

Dr R. E. Robinson, Pr. Eng., obtained a B.sc. (Chem. Eng.) cum laude from the University of the Witwatersrand in 1950 and a Ph.D. (Eng.) from the same University in 1953, where he was awarded the Haikes Memorial Medal for Industrial Chemistry. Professor G. G. Garrett was appointed Professor of Physical and :Fabrication Metallurgy in the Department of Metallurgy at the University of the Witwatersrand in June 1980, and in January 1984 he became Head of the Department. Mr P. A. van Wielligh, Pr. Eng., climbed the mining ladder in the hard way, starting as a Mine Surveyor in 1936 and working his way up as Chief Surveyor, Underground Manager, Mine Manager, and Consulting Engineer, to Executive Director, including the intermediate steps. Mr H. E. James, Pr. Eng., is a graduate in Chemical Engineering from the University of the Witwatersrand. Both his B.sc. degree (1961) and his M.sc. degree (1964) were obtained on bursaries, the former from Gold Fields of South Africa and the latter from the Atomic Energy Board. Mr G. Pienaar, Pr. Eng., obtained a B.Eng. (Met) in 1967 and an M.Eng. in 1973, both from the University of Pretoria. Dr A. K. Haines, Pr. Eng., obtained all his degrees from the University of Natal, finishing with a. Ph.D. in 1971. Mr B. C. Alberts, Pr. Eng., obtained his academic training at the University of Pretoria, where he was awarded B.sc. degrees in both agricultural engineering (1963) and mining engineering (1965). Mr H. C. van Zyl, Pr. Eng., holds B.sc. degrees in mining engineering (1968) and civil engineering (1972), both from the University of Pretoria.

Jan 1, 1984

By Frank J. Foster

This Paper will deal with Bucketwheel Suction Dredging and its particular relationship to mining applications. There will be comparisons with other methods of suction dredging and descriptions of two recent bucketwheel installations in the mining area. The Directory of World Dredging Fleets published in the `larch 1984 edition of World Dredging magazine shows that there are about 1.000 conventional Cutterhead Dredges listed throughout the world with 289 in the United States. There are 242 Bucketline Dredges listed throughout the world of which only 6 are in the United States. These figures are not completely accurate because several units are known to the author that are not on the list and, of course, there may be others.

Jan 1, 1984

In the investigation described here, it was found that the main effect of temperature is on the rate of flotation, and that adsorption of the reagent is not rate controlling. Above 10°C, the flotation rate of pyrite and gangue increases almost exponentially with a rise in temperature. Below that temperature, the flotation rate of pyrite shows a sudden marked decrease, that of gangue increases, and the sulphur grades are significantly poorer. In the flotation of pyrite, the mass transfer of the pyrite from the pulp to the troth is thought to be the ratecontrolling step, whereas the flotation of gangue is controlled by the combined effect of the stability and velocity of the froth and the viscosity of the elutriating medium. The latter is probably the controlling effect at temperatures below 10°C. Little difference was noted in the recoveries (provided no time limit was set) with changes in temperature; hence adequate recoveries can be obtained at Iow temperatures by the introduction of longer residence times for the pulp. The adverse effects of Iow temperatures on grades can be overcome only by additional cleaning or by heating of the pulp.

Jan 1, 1984

By Watson D. F

Armstrong's (1983) criticisms of PhiIip and Watson's (1982b) note on optimal drilling patterns are based on misinterpretation, supported by errors in geometry. Furthermore, Armstrong argues conceptually from the perspective of Matheronian geostatistics, as does also Rudenno (1983a, b). Thus, both authors embrace a global, probabiIistic method of assessing spatial data sets, an approach that must be contrasted strongly with local, deterministic interpolation methods. Some of the important assumptions of geostatistics are outlined and the non-unique nature of the method discussed. A probabilistic approach can be judged appropriate when exploration data are erratic, or known to be unreliable, or when extrapolation is desired. Where data are treated as exact, kriging can give the most biased result if tested against other interpolation methods. We reiterate our previous conclusion that the equilateral triangular grid is approximately 30 per cent more efficient (in terms of numbers of drill holes) compared with a square grid for the same maximum interpolation distance. This is simply due to the improved isotropy of sampling. New, locally-based, deterministic methods for computing ore reserves seem to be required.

Jan 1, 1984

By Berke L. Thompson

INTRODUCTION Purpose of Wall System There were 2379.88 m (meters) of tied back wall along Interstate 77 in the Capitol Complex area in Charleston, West Virginia. The main purposes of this wall system was for aesthetics, reduction of excavation, saving the forested slopes, and control of sloughage of the back slopes onto the Interstate. Failure At 1 PM on Thanksgiving Day, 1982, 3 wall panels fell from the insitu position onto the interstate in a matter of seconds. See Fig. 1. The total length of wall that fell was 29.25m. The height of the three panels varied from 10.06m to 10.36~1 and each individual panel had a length along the highway of 9.75m. These were abutting panels that were approximately in the middle of a section of wall 165.81m long. The panels separated from the remainder of the wall at 2 expansion joints that occur at the ends of every 3rd panel. The reinforced portland cement concrete panels were designed on a 76.2mm (millimeter) batter. See Fig. 2 for Wall Dimensions. The footer for these panels was lm wide, was keyed into sandstone bedrock 0.30m and was approximately 1.52m below the portland cement concrete pavement and shoulder. Thirteen of the 17 panels in this section of wall were tied to the sandstone bedrock behind the wall by either 25.4mm or 34.93mm hollow rock bolts. Two panels on each end of the wall were cantilever type walls. The panels that failed had 25.4m hollow rock bolts. A portion of each panel adjacent to both sides of the failure was pulled out from the rock face and appeared to be in imminent danger of also failing. All of the 21 rock bolts in the panels that fell were separated either at the backface of the wall, in the extension from the wall to the rock face or at the rock face. None of the rock bolts had been pulled out of the bond length in the sandstone bedrock. After considering the condition of the wall and

Jan 1, 1984

By Restarick CJ

A compound cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone, has been used for coal slurry sizing experiments in the range approximately 100 to 300 micrometres. An important feature of the system is the ability to adjust the cut size of the separation over wide limits by adjustment of the flow control valve. Results have been compared with typical fine screening operations. Under roughly equivalent conditions the compound cyclone system can achieve better elimination of extreme fines, but is not as sharp as the screen for coarser size cut-off. Simulations of systems involving combinations of the cylinder-cyclone system with screens indicate that the advantages of both sizing devices can be combined to yield accurately sized products for fine coal cleaning, at much less cost than using screens alone.

Jan 1, 1984

By Dr. O’Neil Thomas J., Donald W. Gentry

Money is like an arm or leg-use it or lose it." -Henry Ford INTRODUCTION If it were not for the existence of interest, the analysis of investment opportunities would be greatly simplified. In the absence of interest, investors would be indifferent as to when cash outlays are made or cash benefits are received. It would, in fact, be irrelevant whether the outlays preceded or followed inflows as long as both amounts are known with certainty. Of course, it does make a considerable difference whether, for example, a firm receives $1 million now or five years from now. The reason is that money does, indeed, have a value which is a function of time. Interest is how this time value is measured. Interest is generally defined as money paid for the use of borrowed money. In other words, interest is the rental charge for using an asset over some specific time period. The rate of interest is the ratio of the interest chargeable at the end of a specific period of time to the money owed, or borrowed, at the beginning of that period. In order to understand why interest exists, it is necessary to take the lender's viewpoint. The lender can justify charging interest for several reasons: 1) Risk: The lender is faced with the possibility that the borrower will be unable to repay the loan. 2) Inflation: Money repaid in the future will be in units of lower value due to inflation. 3) Transactions Cost: There will be expense incurred in preparing the loan agreement, recording payments, collecting the loan, and other administrative tasks. 4) Opportunity Cost: By committing limited funds to one borrower, a lender is unable to take advantage of other available opportunities. 5) Postponement of Pleasure: By lending money, an individual (or organization) is postponing the pleasure which that money could purchase. Each of these is a valid reason for a lender demanding interest from a borrower. The level of interest is, like the price of other assets, determined by supply and demand. Nonetheless, from time to time various analysts have taken a then current average interest rate and broken it down into the components described previously.

Jan 1, 1984

By James Fiore

The Nuclear Waste Policy Act of 1982 provides a set of rules for proceeding with the identification and selection of sites for a mined geologic repository as well as for interim storage facilities for high level waste in the event storage facilities are needed. The following paper summarizes the sequence of procedures in site selection, and presents the interaction of governmental agencies, the states, the public, and affected Indian tribes in this process. Several agencies have published regulations assocated with the selection of high level waste sites. These regulations set down a diverse collection of requirements designed to ensure public safety. This paper identifies the organizations working to satisfy these requirements, and outlines the role of the geotechnical community in performing data collection activities to support these same requirements.

Jan 1, 1984

By Lester A. D. Chin

The cost of bauxite is a multiple of the Bauxite Consumption Factor and the Unit Cost of Bauxite, and is a major cost item at most alumina plants. Bauxite Consumption Factor can be reduced by increasing alumina recovery during processing. Unrecovered aluminas are analyzed and possible research identified, using the framework below: 1. [Unextracted Aluminas] 1.1 Aluminous goethite 1.2 Boehmitic alumina 1.3 Diasporic aluminas 2. [Chemically-Bound Aluminas] 2.1 Desilication product 2.2 Phosphorus precipitate 2.3 Solid-phase lime-reaction products 3. [Alumina Reprecipitated on Red Mud] 3.1 Red mud separation and washing 4. [Physical Loss] 4.1 Liquor 4.2 Alumina dust

Jan 1, 1984

By Armstrong AB

It has been identified that particulate matter in the form of suspended solids and bed load has the ability to adsorb heavy metals. Each year Ranger Uranium Mines Pty Ltd (RUM) identifies potential danger areas which could become major sediment sources during the wet season. Methods of suppressing sediment uptake such as hydromulching and coating areas with Poly Vinyl Acetate (PVA) glue are used. Other methods of reducing the sediment load after uptake such as diversion bunds, filters across drains, stone filters, minor sumps and settling ponds are also used. The 1983/84 wet season saw drain sediment loads reduced to acceptable levels before the water reached the outside environment. Studies to qualify and quantify flows from minor drains are still underway.

Jan 1, 1984