Search Documents

By D. R. Murray

"A promising long-term solution to uranium tailings reclamation has been the establishment of vegetation directly on the waste material. The soil profiles of areas vegetated for 0, 3, 8 and 10years are characterized as to the extent of soil development . The characteristics are compared with the visually interpreted soil profile. Organic matter content is presently the best analytical judge of soil development. Vegetation procedures have produced a build-up of organic matter in the top 10cm of tailings where natural microbial populations flourish. The CN ratio is high and the profile depth shallow, suggesting the need for additional fertilizer applications.IntroductionThe reduction of surface erosion and improved aesthetics of uranium tailings has been accomplished by the establishment of a vegetative cover. In 1971 research concentrated on developing methods of plant establishment at minimal cost and soil amendments on uranium tailings in Elliot Lake , Ontario. One process of stabilization used on a large scale was direct seeding of grasses and legumes into the tailings which had received only limestone and fertilizer treatments. Fertilizer additions were made for varying lengths of time in subsequent years to maintain the established cover.Maintenance-free vegetation would be possible once a soil profile developed with sufficient nutrient recycle and plant regeneration capabilities(1). Tailings vegetated in 1971, 1973 and 1978 that had received either 3 or 5 years of maintenance fertilizers were examined for soil development profiles. The extent of soil development and the relative effect of time and fertilizer would provide direction on reaching the goal of a self-sustaining cover.This paper is an abridgment of Division Report MRP /MRL 81-126 of the same title(2)."

Jan 1, 1984

By Dirk van Zyl

The paper describes the construction of a clay pad in Southern California. The pad consisted of a mixture of in situ soil and imported clay products. The paper summarizes design considerations. Laboratory permeability tests performed on samples removed from the pad formed part of the quality control requirement of the State of California Water Quality Control Board. The paper presents statistical analysis of the data (about 70 permeability tests in total) and their significance in controlling seepage losses. The results obtained from an investigation of the first pad-area after completion of the leach cycle are presented and discussed. Results from visual observations and laboratory tests are presented.

Jan 1, 1984

By Lee J. Raabe

A specialized loading system for tensile and fatigue testing of wire rope was constructed and installed in the U.S. Bureau of Mine Wire Rope Test Facility in Bruceton, Pennsylvania. The computer-controlled closed-loop servo-hydraulic test system which can apply up to 800,000 pounds of force on the rope while stretching it up to 30 inches will be used in the development and verification of hoist rope retirement criteria for ropes in the 1 to 2 ½ in. diameter range. Characteristics and capabilities of the system are discussed.

Jan 1, 1984

By Claudia Gasparrini

Gold, silver and platinum-group elements occur normally in very low concentrations in their ores. Because their market value is in many situations high enough to justify their full recoveries, mineralogical studies before any routine recovery is attempted are particularly important for the description of their manner of occurrence and decision on the appropriate recovery techniques. Gold and silver, although sometimes treated by similar metallurgical processes, may require different approaches and treatments because of the different manner in which they occur in their ores: gold has a relatively simple mineralogy limited to native gold, electrum and less often tellurides. Silver has a very complex mineralogy including over 200 different minerals. On the other hand, gold is more often than silver recovered from ores where its fine grain size requires the breaking of the host minerals by chemical methods. Mineral, grain sizes and host minerals all affect the metallurgy of the platinum-group elements..

Jan 1, 1984

By K. V. Konigsmann

"Concentrate dewatering operations have a significant influence on the economics of base metal beneficiation. The expenditures f or energy and labour per tonne of product are high. The relatively low efficiencies of standard techniques present inducements for process modifications. Development efforts at several Noranda concentrators led to process changes which improved productivity, namely, agitated pulp storage in large vessels, process automation and pressure filtration.IntroductionA program was initiated in 1968 with the aim of improving utilization of manpower and equipment in dewatering operations. The following considerations motivated us in this effort: Firstly, filters and dryers had traditionally been operated continuously and in step with grinding and flotation circuits. The demand for labour and equipment operating time was fixed and was not determined by the rate of concentrate production.Secondly, dewatering equipment had usually been designed to handle the concentrate tonnages which were produced when mill feed grades were high; therefore the equipment operated at less than capacity when treating ores of average metal content. The first goal was the separation of the flotation process from concentrate dewatering by development of a practical storage system for concentrate pulps . A second objective was the gradual introduction of dependable automatic controls. The steep increase in energy costs after 1973 added urgency to the search for dewatering processes which were highly energy efficient."

Jan 1, 1984

By Dale S. Preece

INTRODUCTION In 1975 Congress passed the Energy Conservation Act to establish a U. S. Strategic Petroleum Reserve (SPR) with a capacity of 750 million barrels of crude oil. The most economic storage medium was determined to be salt caverns leached in salt domes in Louisiana and Texas. Salt caverns existed at several sites when the reserve was created. These were obtained by the U. S. Department of Energy (DOE) and used to initiate SPR oil storage. In order to meet the storage capacity approved by Congress, new caverns also had to be leached. To support the resulting design effort, finite element computer programs have been used to determine the creep closure and structural stability of salt caverns Using site specific material properties including creep models, elastic moduli and fracture data, the finite element analyses have replaced earlier empirical approaches to cavern design. This report presents results of such finite element analyses to determine the best cavern roof shape and the minimum pillar to diameter ratio, P/D. These numerical predictions indicate that the current cavern design is safe. FINITE ELEMENT AND MATERIAL MODELING The finite element program used in this study has existed for approximately four years. Its theoritical basis (Key, et al, 1980) and application are well documented It was originally developed to predict the creep around mined openings In bedded rock salt for the Waste Isolation Pilot Plant (WIPP) The program was tested by modeling the creep of salt around a drift and by comparing the results with the predictions of eight other structural computer codes (Morgan, et al, 1981) Since then the program has had continual use for calculations to support the WIPP (Miller, et al, 1982) For about two years the

Jan 1, 1984

By Thomas M. Barczak

The resultant load vector is the representation of the forces applied to a longwall roof support element by caving strata into a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield support prohibit a determination of support resistance simply by summation of leg forces. A method is being investigated by the Bureau of Mines to determine the resultant load vector by instrumenting supports with pressure transducers and strain gages to measure leg, canopy capsule, and lemniscate link forces. This concept has been laboratory tested in the Bureau's Mine Roof Simulator. Functional relationships among variables have been assessed, and confidence intervals have been established for prediction of the resultant load vector parameters.

Jan 1, 1984

By Philip D. Shelton

INTRODUCTION Traditional design of support for permanent underground mine excavations place great emphasis on the magnitude of the maximum radial load which a specific support or lining must sustain. However, this depends upon so many factors that reliable prediction in advance of excavation is very difficult except in strong-self supporting ground. Some of the factors affecting the loads acting on a support are illustrated in Table 1. [ ]

Jan 1, 1984

By J. M. Floyd

The theory, construction and applications of oxygen sensors employing high-temperature electro- chemical cells with solid electrolytes are briefly reviewed. The application of disposable probes to measurement of the oxygen potential in matte and slag baths in tin, copper, and nickel smelting operations is described. Examples discussed include end-point determination in smelting and slag-cleaning operations, pilot-scale investigations of process chemistry to assist in the development of smelting strategies, and measurements in operating smelters to improve the efficiency of operation.

Jan 1, 1984

By Lito C. Mejia

Diesel-powered equipment operating in a gassy underground mine could conceivably ingest a methane-air mixture from the mine atmosphere that could cause the diesel engine to overspeed, or exceed its rated speed. Engine overspeed, particularly if extreme (engine runaway), could result in personal injury, a possible mine explosion, and/or catastrophic engine failure. In this report, the Bureau of Mines reviews the literature on the potential hazards of methane-induced diesel engine overspeed. Also included are the Bureau's findings from consultations with representatives of the diesel engine industry to determine the specific engine behavior that could he expected under the overspeed condition. The report summarizes data on mine accidents involving methane, discusses results of tests on the compression ignition of methane in diesel engines, and examines fuel governors and intake-air-cutoff devices, two kinds of devices used to prevent overspeed. Analysis of the information gathered suggests that the conditions necessary to cause a diesel engine to overspeed uncontrollably are not likely to occur, particularly if the engine is equipped with flame-proofing devices. The available literature and lack of actual overspeed case histories suggest that the safety devices currently in use are sufficient to prevent diesel engine overspeed.

Jan 1, 1984

By K. Yatsunami

NKK has developed a new cold bonded pellet process. The features of this process are; 1) it is a continuous process with 10 hours curing. 2) Products can be used as materials for various metallurgical furnaces. 3) Various kinds of slag are used as binders if necessary. 4) The quality of products is excellent. The pilot plant completed in 1981 is now being successfully operated. We are also constructing a commercial plant at our Niigata works. We produced cold pellets containing carbon as material for ferroalloys (Si-Mn), by pilot plant and used them in furnaces. Consequently, considerable economic advantages were obtained.

Jan 1, 1984

By Van Groenou B

Traditionally mining and conservation have been regarded as opposing and mutually exclusive concepts of land use. Often problems are anticipated which cannot be substantiated by facts. In addition, an ill defined time-scale adds to potentially emotive issues. Examples from Australia and elsewhere are presented which illustrate the dynamic nature of the environment and accentuate sequence patterns in plant community development following natural and man-made disturbances. The mining industry generally appears to be aware of the environmental impact of mining and whilst endeavouring to minimise the disturbance, is still orientated towards maximum production.

Jan 1, 1984

By Robert R. Brookshire

Brush plating has been thought of by many as black magic bordering on alchemy. Actually it is a science that uses both electro-chemical and mechanical engineering skills and technology. We are not sure when brush plating was first used or by whom. I do know that many times when we would put in for patents on things we thought of as new and innovative, we would find that someone had done it many years before. It took World War I1 to get brush plating off and running. Now at this point, someone may be asking just what is brush plating? And why are we plating brushes? One way of describing what brush plating is, is by telling what it is not such as tankless plating. Brush plating-is an electro deposition of an electro-platable element or alloy onto a conductive surface. To do this a source of direct current is required; this can vary widely. I prefer stepless voltage control from 0-35 volts with a capacity depending on the size job to be done. This can vary up to 500 amps for normal applications. In one case we have used 7500 amps.. In the beginning a brush was actually used with a wire in the middle of the bristles and a jelly-like paste made up from tank plating solutions. The bristles were saturated with the gunk and the spot to be plated was muddled with the concoction at a potential which was the same as the applied tank Voltage. Metal was deposited but only thin coats were achieved. Today we use graphite wrapped or covered with cotton to form a Q-tip type anode. By using graphite rather than a specific metal we are able to either plate, de-plate or strip, electro- mill, electropolish, or anodize--all with the same equipment. Only the electrolyte needs to be changed.

Jan 1, 1984

By P. M. Yavorsky

Using a mine roof simulator press capable of duplicating the expected magnitude of vertical and horizontal forces experienced by underground mine roof supports, load capabilities of some roof support cribbings were measured. Comparative ultimate vertical support strengths are reported for cribs of old and new timber and nonreinforced and steel-fiber-reinforced (SFR) concrete blocks. In terms of load- bearing capability, cribs of new hickory and nonreinforced concrete blocks have about equal strength, and SFR concrete blocks are three times as strong. Wood aged 2 years underground lost 43 pct of its support strength. These data were obtained during the course of the initial familiarization exercise of the complex press.

Jan 1, 1984

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council. Although the worldwide readership of the Journal results in a preference for papers in English, the Council treats papers in Afrikaans on an equal basis, but, to meet the needs of the majority of readers, an English summary of some 5OO to 750 words should be provided.

Jan 1, 1984

By D. N. Sutherland

The cassiterite flotation circuit at the Renison concentrator has operated with increasing levels of automatic control since late 1981. The circuit operates at high levels of recycle which make it difficult to control manually so that the initial control strategy was to stabilize the mass flows around the circuit prior to circuit optimization. Control of the air supplies to the flotation banks was introduced to achieve this stabilization and initial results indicated that some success has been achieved, as indicated by improvements in the overall circuit performance and reduction in the stream variabilities. These improvements were gained through control of the major recycle to the roughing stage which dominates the circuit behaviour. Feed-forward control of collector addition has also been introduced successfully, but attempts to control the final concentrate grade have been less satisfactory. This work is continuing and the objective of current activity is to include the three cleaning stages in an overall circuit control scheme as a first phase of metallurgical optimization of the operation.

Jan 1, 1984

By Johan K. Rodenburg

A major bauxite belt was discovered and evaluated from 1969 to 1974 by P. T. Alcoa Minerals of Indonesia in West Kalimantan, Indonesia. The proven reserves of beneficiated bauxite are 800 million tons averaging 38.6% AA1203 and 3.0% RSiO2. Inferred reserves of washed bauxite are in excess of 2 billion tons. The bauxite occurs as capping of low lying hills which were formed during the post Paleogene peneplaination stage. The overburden varies from 0.6 to 3.8 meters and the nodular bauxite horizon from 2.2 to 5.2 meters. The deposits were formed by the in situ weathering of predominantly acidic and basic intrusive rocks.

Jan 1, 1984

The captions to Figs. 1 and 2 of the paper by B. J. Parry entitled 'High-strength cold-rolled steels' should read as follows:

Jan 1, 1984

By Gregg A. Scott

Upper Stillwater Dam is to be a roller-compacted concrete gravity structure, founded on nearly horizontally bedded sandstone and argillite rock. An overview of the testing and analyses used to evaluate the adequacy of the foundation relative to deformation, seepage, and stability is presented.

Jan 1, 1984

By David Sugden

Intense, tropical weathering of Cretaceous-Tertiary sediments has developed similar laterites in distant areas of the Amazon Basin. In two areas, Trombetas and Paragomina s, bauxites of commercial potential arc found. The bauxite comes mostly from the lower horizon of the three component laterite. The laterite is overlain by a clay cover, possibly an integral part of the weathered profile. The laterites are found on almost flat plateaus with individual areas of up to 80km2. There is a close relationship between the morphology and the ldterites. The process of lateritization is allegedly Pliocence but probably continues today.

Jan 1, 1984