Search Documents

By S. A. Hoenig

Introduction In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in Fig.1 . Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in Fig. 1. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 µm (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 pm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform. *The zeta potential is the voltage developed between the surface of a solid particle and the ion solution in which it is immersed. In the case of rock/ore materials in water, the zeta potential is negative.

Jan 1, 1984

Courses in chemical engineering and metallurgical engineering at the University of Queensland were compared and the main difference was found to be the greater emphasis on the application of chemical engineering fundamentals, particularly chemical thermodynamics, to specific processes in the metallurgy course. This reflects the distinctive features of extractive metallurgical processes which are not common in other chemical engineering processes and which justify the study of extractive metallurgy in its own right. B.Sc. courses in metallurgy provide one way in which the specialist knowledge of extractive metallurgy can be taught. General metallurgy courses are considered to be preferable to those restricted solely to extractive metallurgy since graduates of a general course have a wider choice of employment, while excessive emphasis on extractive metallurgical applications in chemical engineering courses could reduce the non-specific nature of these courses. Postgraduate diploma and higher degree programmes are avenues for non- metallurgists to acquire knowledge of the discipline.

Jan 1, 1984

By J. N. Hartley

Uranium mill tailings, waste products of uranium extraction, contain hazardous constituents that if released into the atmosphere and groundwater could threaten our health and environment. To provide for safe disposal and control of these tailings, Congress enacted the Uranium Mill Tailings Radiation Control Act of 1978 (Public Law 95-604). Subsequently, the Environmental Protection Agency (EPA) established standards for tailings disposal that limit radon emission into the air to 20 pCi m-2s-1 on an annual average basis (EPA 1983). The design life of the impoundment is to be 1000 years where practicable, but 200 years at least. To facilitate the design of containment systems that will meet the EPA standards, the Nuclear Regulatory Commission (NRC) and the Department of Energy (DOE) are sponsoring research at the Pacific Northwest Laboratory (PNL)* to develop the necessary technology. Earthen and asphalt materials have been evaluated for use as radon barriers (Hartley 1983) and as liners to minimize leaching (Buelt 1983). Herbicide and rock barriers against biological intrusion have been evaluated (Cline 1982). Surface stabilization techniques have been investigated to maintain the long-term effectiveness of a containment system that must be protected from wind and water erosion, chemical and physical degradation, and biological disturbance.

Jan 1, 1984

Ranger Uranium Mines (RUM) operates an open cut located in the Top End of the North- ern Territory. Strict environmental controls govern all operations and the water management requirements have the greatest impact on mine planning. The two main goals of planning are to provide mill feed and to mine sufficient suitable quality waste rock for ongoing con- struction of the tailings dam. Early planning concentrated on staged development of the pit to provide access to as much ore as possible for a given amount of development. All waste was considered to be suitable construction material. Grade control of crusher feed was the main problem in planning, as wide vari- ations occur in ore grade over relatively short distances. Water management for the site ope- rates a no release' system for contaminated waters. Design storage has proven inadequate, and the open cut has been used as the extra storage. As construction of future stages of the tailings dam requires non-mineralised rock materials which meet specific quality criteria, the mine has had to re-examine long term plan- ning and pit development strategies. This has entailed the collection of much data not re- quired under normal mining conditions, such as the assaying of waste drill core. The overall impact on mine planning of the environmental regulations has been to alter the philosophy of earlier planning, making it necessary to create a new strategy for pit development with

Jan 1, 1984

By James W. Clark

This paper is a description of certain geologic aspects of the Inspiration mining operation. It is not a geologic description of the Inspiration deposit nor an exposition of all the geologic work involved in the development and exploitation of the deposit. A few specific examples of the application of geology and geostatistics to the mining process are given to illustrate the progress that has been made in making the Inspiration Mine more efficient and cost effective, and a statement of the philosophy of geologic applications is offered.

Jan 1, 1984

By M. Cross

INTRODUCTION The results of the Japanese dissective investigations have [l-4] transformed our understanding of how the blast furnace operates. These studies revealed an internal structure of the furnace burden with five main zones, as illustrated in Figure 1. In the granular zone the charged material retains its structure whereas in the cohesive zone the iron ore particles are at advanced stages of reduction and form a semi-molten mass with a relatively high flow resistance. In the active coke zone molten iron and slag flow through a matrix of loosely packed coke. The raceway is a relatively small void space generated by displacement of coke due to the hot blast momentum, whilst the hearth is packed with coke, slag and molten iron. [ ] It is now well appreciated that furnace control is largely achieved and maintained by using the burden charge distribution to determine the gas glow distribution within the furnace and, hence, the shape and extent of the cohesive zone. In fact, Wakayama et a1 [5] of Nippon Steel Corporation state that optimum furnace operation is synonomous with the formation of a desirable cohesive zone shape, which in turn is almost solely determined by the burden charge distribution and its mechanical properties [6]. Much of the development work on operating furnaces since the dissective investigations has been oriented towards the identification of external furnace measures which reliably predict the shape of the cohesive zone. Currently the most popular measures are top gas temperature, velocity and CO/CO, ratio profiles [5]. More recently pressure distributions as evaluated from a series of wall measurements down the height of the furnace are also being utilised [7] to identify the position and shape of the cohesive zone. A great deal of emphasis has been placed upon achieving a consistent quality in the burden charge materials, establishing a suitable set of operating conditions and only making changes when forced to, ie., the operation for some reason moves outside a desired operating range or the production requirements change. Operational control schemes based upon this philosophy (eg., Kawasaki's GO-STOP system [8]) have been remarkably successful at achieving both high production rates and relatively low fuel costs. Mathematical models have long been used as tools to assist in the analysis of the blast furnace process. Although, the models have been useful in post-operative analysis and for identifying trends, etc., they have not proved reliable for detailed design criteria or as the basis for effective control schemes. Such mathematical models have moved from simple statistical correlation, through overall and stagewise heat-and-mass balance calcu-

Jan 1, 1984

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company's success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By S. J. Mitchell

An analysis of bolting reinforcement of several large [approximately 18 m (60 ft) cube] pillars was performed. The many overcoring stress profiles in pillars at the mine were used to produce generalized stress distributions at various stages in pre- and post-failure. A complete stress-deformation curve was estimated from this data. The effect of pillar bolting on the load-deformation behavior was extrapolated from the observed unbolted behavior. Bolting can increase pillar strength by up to 10 percent. The effect of bolting on general mine stability was examined with a shoW computer analysis. The computer model was calibrated against measurements performed at the mine, and produced good agreement between measured and modeled stresses. The analysis indicated that bolting increases the bolted pillar safety factors in the event of additional pillar failure by a small amount (approximately 5 percent). Progressive pillar failure is unlikely, because arching transfers most load from yielding pillars to large unmined abutments rather than to the smaller panel pillars.

Jan 1, 1984

By Arthur V. Petty

The Bureau of Mines has researched the utilization of mining and pro-cessing wastes as raw materials for the production of glass-ceramic pipe. Characterization of various wastes as to occurrence and chemical composition is reported. A computer program was developed and used to identify waste materials and mixes that would result in glass melts from which glass-ceramics could be produced after cooling and subsequent heat treatments. The production of abrasion-resistant pipe from inexpensive and readily available domestic resources could offer an economical substitute for high-alloy steels containing the critical and strategic materials cobalt and chromium.

Jan 1, 1984

By John B. Wright

This paper describes laboratory techniques and subsequent results of Bureau of Mines research to produce chlorination-grade feedstock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau-effort to devise technology that may help decrease U.S. dependence on imported raw materials. A rock ilmenite containing about 46 wt pct Ti02 was smelted in an electric arc furnace with coke, woodchips, and Na2C03 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slag. The slag was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1- kg/h apparatus at 1023 to 1223 K. The sulfated slag, containing 60 to 65 pct TiO2, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome Ca, Mg, and Mn impurities from 7.0 to 1.7 wt pct. At levels of more than 3 wt pct, these impurities contribute to operating and disposal problems, The final product was upgraded to about 84 wt pct TiO2. This material potentially is suitable for chlorination in a fluidized-bed reactor. The most favorable results were achieved with leached slag sulfated at a feedrate of 4.5 kg/h and at temperatures of 1073 to 1123 K.

Jan 1, 1984

By Richard R. Klimpel

This paper takes the liberation model recently developed by Klimpel and Austin for liberation from a binary system and reduces the over-all model form to a number of useful limiting cases. General use of the complete model form, while quite broad in utility, requires a numerical integration computer program for prediction of liberation given a specified minor component grain size distribution coupled with an optimization algorithm such as linear programming in order to back- calculate the associated grain size distribution from experimental data. In this paper, analytical solutions to the model are achieved for various assumed distributions of the minor component. These solutions are algebraic equations capable of predictive use with a hand calculator and back-calculation with very simple trial and error search procedures. The use of these special model solutions is illustrated on several sets of experimental liberation data, and the approach is shown to have practical utility.

Jan 1, 1984

By Dietmar Espig

Very useful general relationships between operating parameters and the operating results for open- and closed-circuit grinding under steady- state conditions are described. The basic idea of the developed methods consists of the introduction of a known reference state. The relations derived from very simple approximations to individual processes allow one to evaluate fineness and mass flow of the desired state after changing the parameters (feed rate, fineness of the feed material, mill length, transport behavior through the mill, classifier characteristics). It was also possible to derive some general relationships, e.g., * an equation for the influence of the operating parameters of the mill on the fineness of the mill output * a criterion to establish if the desired state of a closed grinding circuit is steady state at all * a possibility to substitute the common influence of the transport behavior of the mill and of the classifier by-pass fraction with the coarse stream on the mill outlet product by means of a fictitious worse transport behavior. The applicability of the described methodology to many problems in grinding practice, including questions of controlling grinding circuits, is demonstrated by some examples. In particular, a working diagram of the standard closed grinding circuit has been established.

Jan 1, 1984

By A. K. Gangopadhyay

This paper discusses the effect of grinding media composition, mineral type and slurry environment on the wear rate of various grinding media (balls). Sufficient wear data have been obtained and correlated with the modes of wear determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1984

By Samuel G. Bonasso

The article by Benavides and Schuster provides an in-depth study of this transportation alternatives for a four-mine complex in western Kentucky. The examination of aerial tramways was not undertaken as an alternative solution. We feel this is an oversight since industrial ropeways are competitive with both belt conveyance and overland truck hauling. In fact, there are aerial tramway system, operational today, which are 100 years old and operating with some original components. Maybe unfortunately, there are no fixed rules or guidelines whereby the most cost-effective means of transporting and handling material for a given situation may be selected. Each situation must be evaluated m the variables that influence the selection of the desired alternative can be clearly defined. However, there are in-place industrial ropeway system that have proven economically feasible over a range of 1.6-50 km (1-31 miles). The more difficult the terrain, the greater the cost efficiency.

Jan 1, 1984

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique: the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi- normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By J. D. Miller, A. Cortez, J. Hupka

The separation efficiency of the hot water digestion-flotation technique used for bitumen recovery from various domestic tar sands was evaluated. Bitumen viscosity was found to be the most important tar sand property in determining the success of the bitumen separation. Bitumen viscosity of the tar sand war controlled by changes in digestion temperature and/or changes in diluent (kerosene) addition. Complete and uniform dilution of the bitumen phase was achieved by providing a sufficient presoaking, or penetration time, for a given tar sand type. For all the tar sand samples tested, an excellent correlation was obtained between the coefficient of separation and the bitumen viscosity. To achieve a satisfactory coefficient of separation, it was found that the bitumen viscosity must be reduced below 1.5 Pa.s (16 P) at the temperature of digestion. This was the case regardless of the tar sand type, grade, or origin.

Jan 1, 1984

By Hun-Joon Sohn

Chemical metathesis and electrochemical reductive conversion of chalcopyrite in the presence of cupric ions were studied in sulfuric acid solutions for temperatures up to 90°C. The process results in the displacement of iron in the chalcopyrite lattice by copper ions with rejection of ferrous ions to the aqueous phase. The rate of reaction was found to be very slow, requiring subsieve-sized particles for extensive reaction to occur. The reaction was insensitive to copper ion concentration. Stirred ball milling of chalcopyrite introduces lattice strain. The reaction rate with strained particles was markedly higher than with annealed chalcopyrite. The reaction rate was found to be diffusion-limited, showing two distinct reaction stages corresponding to the formation of CuS (covellite) followed by Cu1.8S (digenite). The experimental activation energy for the first stage was 102 J (24.4 kcal) and the second stage 123 3 (29.4 -kcal) per mole. The rate-controlling process is diffusion of lattice ions, probably iron. The enhanced rate after milling is attributed to a recrystallization process which provides new paths for diffusion along dislocations and grain boundaries.

Jan 1, 1984

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department's Bureau of Mines.

Jan 1, 1984

Exploration for uranium in Australia commenced only during the 1940s, but in this short period has been very successful as one third of the world's low cost uranium reserves have been discovered in Australia. Total uranium exploration expenditure in Australia up to the end of 1983 was $A(1983) 554 million; this discovered 20 potentially economic deposits and official reserves of 560 000 tonnes of uranium oxide at an average cost of $1 per kg of U 0 . An exponential 8 eserves indicates distribution of uranium r that there could be 54 undiscovered uranium deposits in Australia, each with reserves of 20 000 tonnes U308 or more, in addition to smaller deposits. Using a constant uranium price of $A(1983) 79 per kg, no deposit is economic at a grade below 0.12 per cent U 08 or with reserves of less than 3 000 tonnes. Selecting deposits with reserves of 5 000 tonnes U 0g or more as prime exploration targets, only 39 per cent of discoveries will yield a real internal rate of return (IRR) of 10 per cent or more. After committing a minimum exploration budget of $10 million to this search, an explorer has one chance between 7 and 12 of discovering a deposit that will repay the exploration investment.

Jan 1, 1984

By Allan R. Ide

It is a great pleasure for me to speak-before such a prestigious group as the American Institute of Mining, Metallurgical and Petroleum Engineers. The substance of my talk today is the handling of coal and petroleum coke: their characteristics and environmental problems, and how we were able to correct the problems, prescribe the cure and enjoy the benefits. When coke first became a by-product derived from the oil refineries everyone would have been very happy if someone had offered to take this pro- duct off their hands. Unfortunately, there was no market at that time, and no one seemed interested. Soon thereafter, it became a sellable product and began to be shipped to many countries in the world. This was when all of the pollution problems began. I will be talking briefly about some of these problems and showing a short film on this subject afterwards.

Jan 1, 1984