Search Documents

By Sebastian Paul Musco

The importance of the recovery of precious metals, specifically platinum group metals, was recently expressed by Robert McNamara, former head of the World Bank, who stated that the United States should stockpile strategic metals. More than 90% of the platinum metals are imported into the United States from South Africa and Russia. Mr. McNamara's concern is based on the possibility of a disruption of obtaining these metals due to any racial unrest in South Africa and a renewal of the Cold War with Russia. The United States has a platinum mine from coast to coast. Since 1974, the automotive industry has consumed 3 million ounces of platinum and palladium, and the recovery of these metals from auto catalyst converters is estimated to be 300,000 ounces of platinum per year. This would make the United States the 4th largest producer in the world.

Jan 1, 1984

By Robert L. Skaggs

Sixteen nonaqueous techniques conceived to replace the current aqueous scheme for separating hafnium and zirconium tetrachlorides were re- viewed and evaluated by the Bureau of Mines. The methods are divided into two classes: separation by fractional volatilization of the tetrachlorides, which takes advantage of the higher volatility of hafnium tetrachloride; and separation by chemical techniques, based on differences in chemical behavior of the two tetrachlorides. The criteria used to evaluate separation methods were temperature, pressure, separation factor per equilibrium stage, complexity, compatibility with existing technology, and potential for continuous operation. Three processes were selected as being most promising: (1) high-pressure distillation, (2) extractive distillation from a molten salt, and (3) preferential reduction of gaseous ZrC14. Any of the proposed nonaqueous Hf-Zr separation schemes must be supplemented with additional purification to remove trace impurities.

Jan 1, 1984

By Niemann G

The paper addresses certain mining provisions of the Aboriginal Land Rights (Northern Territory) Act 1976 and the development of Mining agreements negotiated pursuant to Section 43 of the Act. Difficulties for miners and Land Councils alike arising out of the operation of the Land Rights Act will be discussed. Possible scenarios for the resolution of these difficulties will be proposed.

Jan 1, 1984

By R. M. Schuster, F. M. Benavides

This study compares the costs of transporting coarse coal by pipeline versus more conventional belt conveyors. Hydraulic conveying of crushed (not pulverized) coal has not had widespread commercial acceptance. However, there is little doubt that the technology is available, so that, should this method be proven economical for a given application, implementation will become more acceptable.

Jan 1, 1984

By P. E. Venteer

The Grootegeluk coal-processing plant treats 3 kt of raw coal per hour to produce a middlings fuel coal and a coking coal fraction with ash contents of 35 and 10 per cent respectively. The plus 0,5 mm fraction is treated by heavy-medium processes, the final top size of the coal being 15 mm. About 400 t of minus 0,5 mm coal per hour is subjected to froth flotation. The routes originally considered for the processing of this fine coal were froth flotation, shaking tables, heavy-medium cyclones, and water only cyclones in combination with froth flotation. The results from tests on the fines arising from a small-trial open-cast mine are discussed. When the froth flotation route was decided upon, further tests were conducted on the selection of the equipment most suited to the particular requirements of this coal and the rest of the plant. Tests using different types of flotation cells and dewatering equipment are discussed. During the commissioning, several operational problems were encountered, and the work done to find the best solutions is discussed.

Jan 1, 1984

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique; the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi-normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By C. McLean, Erickson, S. G. Kolb, S. C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined with underground workings during 1980-82 by Esso Erz GmbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceives as a cost-effective procedure to answer quest ions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gamma probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross-cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 m thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1984

By T. J. O’Neil, S. J. Kirk

In 1978, a multidisciplinary team from the University of Arizona, the Mines Project Group, conducted a study to examine reclamation alternatives for a proposed open-pit copper mine. The cost of a waste dumping plan designed by a mining consulting firm was determined as well as the cost of dumping configuration prepared by the Mines Project Group. The latter dumps were designed to be more socially acceptable and aesthetically pleasing, in addition to serving more creative end land uses than the dumps designed by the mining consultant. One dump configuration designed by the interdisciplinary team was the least expensive plan of all the alternatives considered.

Jan 1, 1984

By A. M. Crawford

INTRODUCTION Grouting is an engineering operation which has been practiced for many years and a considerable amount of experience and skill has been developed in this field. However, a review of the current literature (Houlsby, 1982) reveals that the theoretical background and experimental observations that are necessary to adequately predict or describe the performance of a particulate grout (e.g. cement based) in a jointed geologic media are somewhat inadequate. In the near future it is envisaged that the use of grout and grouting techiques will be used to tackle even more difficult problems than have been considered in the past. One problem that is currently being faced by the rock mechanics engineer is the development of geologic repositories for the disposal and containment of high level radioactive waste. In such structures there will be only one opportunity to ensure the success of the containment system. This success will depend to a large extent on the adequate and successful performance of the grout curtains to be utilized around the shafts and shaft liners. Regrouting will not be possible. There are other problems in rock mechanics in which it is frequently necessary to inject particulate media into passages of small dimensions, and where typically the size of fracture being injected is of the same order of magnitude as the particle dimension. For example, in the oil industry in hydraulic fracturing the enhancement of fracture conductivity is maintained by means of proppants introduced into the fracture.

Jan 1, 1984

By Paul R. Thomas

This paper addresses the long-term cost and availability of primary gold production from the Republic of South Africa. Forty-four major producing or developing operations were evaluated. The analyses present estimates concerning 1) total refined gold potentially available from demonstrated resources, 2) annual production potential into the next century, 3) long-term weighted average total costs for underground mine production and surface waste reprocessing, 4) the expected annual decrease in gold production, and 5) the ability of other market economy countries to compensate for the anticipated decline in South African gold output. This paper draws upon the data and analyses of a recent Bureau of Mines, U.S. Department of the Interior, Minerals Availability Program appraisal that evaluated the worldwide availability of gold and silver from primary precious metal operations and as a byproduct of base metal production.

Jan 1, 1984

By Christopher H. Roe

This Bureau of Mines report reviews the various methods of removing the liquid from tailings slurries that contain very fine grained solids. Gravitational settlement, centrifugation, filtration, and thermal drying methods are discussed in detail. Chemical additives, electrokinetic dewatering, and the rotary trommel screen are also mentioned. Lists of dewatering equipment and suppliers are given in the appendixes to assist the planner who must choose the most efficient, economic, and practical method of dewatering very fine grained mill tailings.

Jan 1, 1984

Improve the effectiveness of face ventilation systems in coal mines by minimizing leakage around line and check curtains. Approach In-mine surveys were conducted to determine current curtain construction techniques, their effectiveness and associated costs. In addition, performance characteristics of extensible curtains were evaluated. A total of 77 conventional curtains in 10 mines was examined for 12 important characteristics. Extensible curtains were erected in a full-scale model and examined for operational difficulties, effects of leakage, and air pressure. Survey Results The underground mine study identified four categories of face brattice construction ranging from simple to complex: 1. Simple suspension of the curtain from roof bolts with the bottom edge lying on floor. 2. Spadding of the curtain to the roof on about 12-inch centers and stabilization of the bottom edge with wood or rock. 3. Use of vertical props and spads with a base board for support on the bottom. 4. Use of vertical props with caps and bottom boards plus horizontal brattice support boards.

Jan 1, 1984

By John Kafritsas

INTRODUCTION Deformations and failure of rock masses in elopes, foundations or tunnels can be caused by water pressures. On the other hand, deformations of a rock mass affect the flow of water (and hence water pressures) by changing joint apertures. Including the coupling between flow and deformation effects is therefore important both in assessing the stability and deformation of a rock mass and in determining the amount of seepage taking place through it. The model that will be presented hare treats the coupling of the flow and deformation behavior of a rock mass. Deformations are modeled using the Rigid Block Method (Distinct Element Method) (Cundall, 19741, that is by assuming that the rock mass is composed of rigid blocks with deformable contact points. Flow is modeled by recognizing its discontinuous features, as occuring in a system of interconnected conduits formed by the joints. The program can also deal with problems involving free-surface flow. Example problems involving representations of rock masses are presented. Coupled flow modeling of interconnected conduits should be contrasted to equivalent-continuum models on the one hand and to pipe network models on the other hand. Continuous models substitute an anisotropically permeable continuum for the discrete flow that occurs in rock joints. Pipe or parallel plates represent the other extreme of existing models; they account for the discontinuous character of the flow problem, but cannot model rock mass deformation and failure. The coupled rigid block-flow model can eliminate most of these restrictions. The coupling between water flow and deformation is most pronounced in rock masses which, because of the arrangement of their

Jan 1, 1984

By D. G. Hartley, P. C. Hayward, K. R. Weller, U. J. Sterns

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five Primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balk. For five months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm (2 to 1.1 in.). Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balk. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 2%.

Jan 1, 1984

By Bernard S. Covino

The Bureau of Mines is conducting a study of methods to improve the efficiency of the process used to pickle stainless steels. A review of the literature on pickling of stainless steels showed that the chemistry of several process operations involved in the pickling of stainless steels is not fully understood, and that further research could improve the pickling efficiency. The benefits of this research would be a reduction in the annual loss of several thousands of tons of critical minerals such as nickel and chromium, and a reduction in the amount of solids and spent acid solution that are currently discarded. The conclusion from this review is that further research is needed in four operations that either directly or indirectly influence the pickling process: hot working, annealing, conditioning, and the actual operation of pickling, Laboratory studies of the pickling operation are presently in progress.

Jan 1, 1984

By J. A. Herbst

Ball mill grinding circuits can be subject to upsets that arise from variable characteristics of the feed ore. These upsets are transients in critical circuit variables such as ball mill mass holdup, circulating load, sump level, cyclone efficiency and product particle size. They may occur frequently so that the operation is continuously fluctuating or they may be of such magnitude that some of the equipment is overloaded, resulting in shutdown, or an undesirable product particle size. The feed ore characteristics that influence ball mill circuit behavior in this manner include the grindability of the ore, the eventual transport characteristics of the ore in the mills and the feed ore size distribution. Control strategies for grinding circuits using conventional proportional-integral (PI) control have limitations to their effectiveness in controlling against feed ore disturbances. The first of these are the interactive nature of two or more control loops on a single circuit. Under some circumstances they begin to fight each other, increasing control error and settling time. PI control loop gain constants can be tuned to give best response for some set of conditions but once these change, as they would with a change in the feed ore, they are no longer the "best" ones (Shinsky, 1967). Due to these limitations, alternatives to conventional PI control strategies have been investigated for grinding as well as other mineral processing operations. These alternatives, all computer-based, include self tuning regulators, decoupling control and optimal control (Herbst and Bascur, 1983).

Jan 1, 1984

Professor R.P. King holds a Ph.D. degree in chemical engineering, which he obtained at the University of Manchester in 1963. After that he lectured in the Departments of Chemical Engineering at the Universities of the Witwatersrand and Natal. From 1968 to 1973, he was Leader of the Chemical Engineering Research Group of the National Institute for Metallurgy at the latter University. Mr C.E. Fivaz, Pr. Eng., is Chief Consulting Metallurgist of Rand Mines (Mining & Services) Limited, and is responsible for the metallurgical activities of the Gold and Uranium Division and the Coal and Base Minerals Division of the Group.

Jan 1, 1984

By J. A. Eisele

The Bureau of Mines has played an important role in the revival of precious-metal mining underway in the Western United States. During the past 30 years, many techniques used by industry to recover gold and silver were pioneered and developed by the Bureau of Mines. In 1952, technology was developed to strip gold from granular activated carbon and allow the carbon to be reused. In 1969, the heap leaching concept was applied to low-grade gold and silver ores and mine wastes. Heap leaching in conjunction with carbon adsorption-desorption permits very low value material to be economically processed. In 1970, an oxidation treatment based on hypochlorite was developed to increase the recovery of gold from carbonaceous gold ores by cyanidation. In the early 19501s, attempts were made to employ carbon-in-pulp technology to recover gold from ores, but the fixed price of gold and increasing operational costs made the process unprofitable. The Bureau of Mines and Homestake Mining Co. jointly operated a carbon-in-pulp pilot plant, and the technology was used in full-scale production at the Homestake Mine in 1972. In 1973, a pressure stripping method, which decreased the time needed for the stripping step, was developed to desorb gold and silver from carbon. An alcohol desorption method, developed in 1976, also decreased the carbon stripping time. These stripping methods are in commercial use. In 1979, an agglomeration pretreatment was developed that permitted clayey precious metal ores to be heap-leached. Agglomeration-heap leaching technology is being used by at least 30 operations, several of them major gold and silver mines. Almost all precious-metal-mining companies use at least one of the above techniques in production facilities.

Jan 1, 1984

By Peter M. Fozzard

A review is made of the actual costs of recent foreign mineral exploration programmes in third world countries. Target identification leading to the selection of areas, or macro-targets, must follow a well planned and defined series of steps. Suggestions are made with respect to this inter-active project development work. Potential revenues in the broad sense will always determine the overall economics of exploration but clear objective philosophy, good planning and adequate financing are essential for exploration success. Considerable opportunities exist for making important foreign mineral discoveries and broad selected suggestions are made for the identification of exploration areas in relation to high-grade and precious metal mineralization.

Jan 1, 1984

By R. W. Wittkopp

The Relief Canyon gold deposit is located approximately twenty- four kilometers east of the town of Lovelock in Northwestern Nevada. At Relief Canyon, the Late Triassic Grass Valley Formation has been thrust over the Late Triassic Natchez Pass Formation. The lower plate Natchez Pass Formation is composed of massive gray dolomitic limestone which is locally silty and sandy. The upper plate Grass Valley Formation is composed of shale, siltstone, argillite and quartzite. Gold mineralization at Relief Canyon occurs along the highly brecciated thrust contact between these two formations. Weak gold mineralization often occurs above the thrust in the Grass Valley Formation, however, most of the ore grade mineralization is present below the thrust in the brecciated Natchez Pass Formation or where the two formations are mixed as a result of movement along the thrust. Several types of gold mineralization have been recognized at Relief Canyon. A large amount of the ore is present as a jasperoid breccia, however, significant amounts of ore occur as a mixed breccia composed of upper plate rock, fresh limestone, clay and jasperoid breccia. Gold ore also occurs in a fresh limestone breccia which contains a large amount of clay. Below masses of jasperoid, jasperoid stringers containing gold extend into the fresh limestone. Gold mineralization at Relief Canyon appears to be truly disseminated and has the typically associated trace elements of arsenic, antimony, mercury and fluorine. The Relief Canyon deposit can be classified as a structurally controlled disseminated gold deposit. Other deposits that fit this classification are the Pinson and Dee gold mines.

Jan 1, 1984