Search Documents

? A BARGE WILL BE INSTALLED IN THE BOTTOM OF A COMPLETED PIT. ? THE PROVEN BAUER CUTTER TECHNOLOGY WILL BE INSTALLED ON THE BARGE AND A DEWATERING PLANT WILL BE INSTALLED NEAR THE BASE OF THE PIT RAMP. ? THE WATER LEVEL IN THE PIT WILL BE RAISED BY 20- 40 METRES AND REMAIN CONSTANT OVER DURATION OF MINING. ? THE CUTTER WILL BE LOWERED TO MINE 10 METRE DEEP BENCHES ON A CHECKERBOARD PATTERN TO AN ULTIMATE DEPTH OF 200 METRES. ? THE 5? MINUS CUTTINGS WILL BE PUMPED TO THE DEWATERING PLANT, DEWATERED, AND TRUCKED TO SURFACE.

May 1, 2003

By Thos. A. Stroup

From time to time the question of shearing or vertical cutting of rooms and entries especially as an adjunct to the usual horizontal cuts, has cropped up in the literature of coal mining and in the discussions of mining men. Exact and definite data based an thorough tests have usually been lacking however and the present article is written to supply as far as possible this deficiency. The tests given below were made over a period of 90 days in the summer of 1921 and the object was to investigate the general .economics, if any, that might result from the introduction of vertical cutting as a standard practice into the Clear Creek mines. The machine used was the Oldroyd Universal coal cutter and comparative tests were made against the Goodman Straight- face machine and the 35 B Jeffrey Shortwall. The tests however should be held to apply only to the various methods of cutting and not as a study in the relative merits of the various machines. The first series of tests were made in the 2nd East district of No. 3 mine, where only entries were being driven at the time, the tests therefore cover only entry work. The presumption was that the entry width would be 12 feet but the oxerrun in some cases was marked enough to make the work comparable to rooms. The first test made was to determine the time necessary to shear as well as cut the places, and the results were reduced to the time necessary to cut a ton of coal. The time for shearing in the table includes the time necessary to revolve the cutter bar to the vertical position.

Jan 1, 1924

By Ayman Tawadrous, Hendrik Botha, Simon St J Tose

The early miners and their mules always had the challenge of transporting unstable dynamite underground. The modern pumpable explosives, whilst far safer, still present a major logistics challenge for the mobile charging units (MCU). The challenge today is the efficient explosive delivery into declines, ramps, and vertical shafts, often requiring the MCUs to travel excess distances up and down to surface to re-load. Alternatively, the management of cassettes or ISO containers is utilized to deliver the pumpable base emulsion to the MCUs at the working face. Additionally, local laws and regulations regarding shaft clearance further compound the task and result in pausing other operations in the shaft or decline or ramp until the completion of the explosive transport. This paper examines the research & development challenges of dropping base emulsion down a vertical pipe to depths in excess of 1000 m (3280 ft.), either to an underground storage or directly into the MCU, depending on the depth. The boreholes (with pipes) are drilled in close proximity to the underground work areas. The paper also discusses the rheology of the emulsion within these vertical pipes as well as the economic benefits of such an innovative system. The learnings gained from this work, along with examples demonstrating the significant reduction in MCU travel and the safety benefits, are presented for the industry to consider moving forward.

Jan 21, 2025

By Peter J. Nicholson

A new method of constructing retaining walls, in-situ, prior to excavation has been developed. This "Vertical Earth Reinforcement Technique" VERT, has been demonstrated at a full scale test wall at the National Geotechnical Experimentation Site at Texas A&M University. This 10 meter high wall, was constructed of elements of soil mixing in an array that forced composite behavior between the soil mixed elements and the in-situ soils. Inclinometers and extensometers were used to verify the performance of the wall. The construction and results of the testing are presented.

Jan 1, 1998

By Paul M. Vercruijsse

Deep sea mining operations by nature are performed (or planned) in challenging environments. Another typifying characteristic of deep sea mining operations is the relatively high investment cost. This combination challenges engineers to design configurations able to mine the desired production rate in an efficient way. As design choices made for individual systems impact other parts of the system, it is vital to follow an integral approach to establish the one optimal overall system. Dredging and especially dredge mining learns that the excavation system, the slurry transportation system and the processing plant cannot be considered as individual sub-systems. These systems in any ?traditional dredge mining? operation interrelate to such extend that they must be developed towards an integral solution. The nominal production, peak production and variability of these figures must match for all subsystems in the overall mining system to optimize the mining efficiency. We call this the ?game of capacities?.

Jan 1, 2011

By Leslie Taylor, R. Reed Skagga, William Gault

The ultimate aim of our overall task, of which the effort described in this paper is a part, is to be able to model the impulsive output of buried charges and the response of targets of interest. It is not practical or cost-effective to determine the response of all targets of interest to buried charges of all sizes by testing them. In order to have confidence in our models, however, they must be validated by a modest number of tests. A critical element in modeling the response of a target is the ability to model the loading function. The load a buried charge applies to a target above it when the charge detonates can be characterized in terms of the vertical impulse. The vertical impulse is a function of the size of the charge, its depth of burial, and the properties of the soil in which it is buried. The primary objective of the effort described in this paper is to determine the load a known charge places on a non-responding target so the data can be used to validate our models.

Jan 1, 2005

By I. A. Mutemererwa

This paper investigates the role of vertical integration between chrome ore mines and ferrochromium smelters in the location of ferrochromium production capacity in South Africa and Zimbabwe. Vertical integration is important in understanding the increasing competitive position of these two countries as observations show that an increasingly larger share of the global market has been coming from integrated producers. The paper argues that the increased vertical integration between mines and smelters in South Africa and Zimbabwe has led to a lower cost of chrome ore as an input compared with other producers. Underlying this hypothesis is the basic tenet that, more likely than not, production will take place where the costs are lowest. The paper concentrates on high carbon ferrochromium (HCFC) production in market economy countries (MEC). Using an ordinary least squares model, the study tests the relationship between low chrome ore costs and vertical integration shows a statistically significant relationship. These findings partially support the view that the control of sources of chrome ore is a major source of competitiveness. Keywords: competitiveness, ferrochromium (ferrochrome), ordinary least squares, dummy variables, vertical integration, southern Africa.

Jan 1, 2000

By Piezanowski Ludivine

With the aim to reduce the hot metal production cost, ArcelorMittal Gent decided to integrate more ores with finer particle size distribution in the raw material mix for the production of blast furnace sinter. As a consequence of such an increase of finer material in the sinter raw mix, the sinter machine productivity and the quality of the sinter are affected. In order to compensate this impact, modern granulation technology can be employed. Within this context, ArcelorMittal Gent has invested in a vertical intensive mixer. The equipment was placed before the existing drums, with a function of “mixer”, whereas the drums are fully optimised for the nodulizing process. The paper presents the results of the industrial operation during the commissioning phase of the new equipment. Gradually increasing the proportion of fine material in the sinter raw mix has made it possible to compare the performances of the old system using drums for mixing and pelletizing with the new system using an intensive mixer combined with a nodulizing.

Aug 1, 2018

By David F. Gearhart, Khaled M. Mohamed

"Trusses are primarily used as passive roof supports in coal mines. They are constructed of three main parts: two grouted bolts installed at opposing forty-five degree angles into the roof so that they are anchored over the ribs and a cross member that ties the angled bolts together. There is also hardware used to assemble these components. The capacities of the angled bolts are typically 30 to 40 tons and the tensile capacity of the cross member is also 30 to 40 tons. Importantly, the direction of the immediate roof loading on the cross member is unlike the direction of the loading on the angled bolts. The load on the cross member is transverse to the longitudinal axis instead of along it, and therefore the cross member is loaded in the weakest direction.Previous tests conducted on truss systems applied loads such that the increasing tension in the two diagonal bolts increased the tension in the horizontal cross member, resulting in a stiff response. By contrast, if the load is applied directly to the cross member, which then transmits those forces to the diagonal bolts, it results in a much softer response.Based on this difference, laboratory tests to apply transverse loads and measure the vertical load capacity of three different types of cross members were conducted using the Mine Roof Simulator (MRS) located at the National Institute for Occupational Safety and Health (NIOSH) in Pittsburgh. The length of the samples was about 16 feet. Single-point load tests, with the load applied in the center of the specimen were conducted to verify the performance of the test arrangement and the finite element models. Double-point load tests, with a span of eight feet, were also conducted. This arrangement replicates the performance of the cross members with a distributed load. Both of these test arrangements were conducted on one-inch-diameter threaded steel bars and 0.7-inch-diameter cable and 0.6-inch-diameter cable cross members.For the single-point load configuration, the yield of the one-inch bar was nominally 22 kips of vertical load, achieved at 17 inches of deflection. For both sizes of the cable cross members, yield was not achieved even after 18 inches of deflection. Peak vertical loads were about 20 kips for the 0.7-inch cables and 15 kips for the 0.6- inch cables. For the double-point load configurations, the one-inch bar cross members yielded at 33 kips of vertical load and 10 inches of deflection. The 0.7-inch-diameter cable cross members broke strands at 30 kips of vertical load and 10 inches of closure, and the 0.6-inch-diameter cable cross members broke strands at 25 kips of vertical load and 10 inches of closure. Finite element models of each of the six different configurations were developed and show the variation of the vertical capacity of the cross members and the difference of the behavior of the bar versus the cables."

Jan 1, 2015

By Mustapha Zergoun

This paper presents the results of load tests to assess the vertical load carrying capacity of concrete expanded base piles, or pressure injected footings, for various projects located near Vancouver, British Columbia, Canada. The site subsurface conditions and load test methods are described for the Vancouver International Airport site and the test results are reviewed under both compression and tension loading conditions. The pile load tests at Vancouver International Airport are compared to load tests at other sites near Vancouver. The pile load test results are reviewed with respect to available methods of estimating the vertical capacity of this type of piles. The effect of ground improvement by densification on the load test results is considered. The limitations of tension load tests on single piles with respect to uplift resistance of pile groups under seismic conditions are pointed out. Recommendations are proposed regarding pile load test methodology to estimate ultimate vertical load carrying capacity of plies for limit state design.

Jan 1, 2004

By J. Hamada, K. Yamashita, Y. Shigeno, T. Tanikawa

"This paper offers a case history of piled raft foundation in soft ground supporting a twelve-story building in Tokyo. To increase bearing capacity of the soft soil as well as a countermeasure of liquefaction, grid-form deep cement mixing walls (DMWs) were employed with the piled raft. Based on the long-term monitoring results, the ratio of the load carried by the DMWs to the effective structure load after the construction of the raft was estimated to be 0.3 while that carried by the piles was 0.7. In order to clarify the contribution of the DMWs to bearing the structure load, numerical simulation of the settlement and the load sharing among the piles, the DMWs and the unstabilized soil was performed using a three-dimensional finite element model. The results of the numerical simulation agreed well with the measured values, when the Young’s modulus of the DMWs obtained from the unconfined compressive tests was adopted and the shear modulus of the soft soil was reduced to 50% of that at small strains.INTRODUCTIONIn recent years, piled raft foundations have been used in many countries as building foundations. The effectiveness of piled rafts in reducing average and differential settlements has been confirmed not only on favorable ground conditions as shown by Katzenbach et al. (2000), Poulos (2001) and Mandolini et al. (2005), but also on unfavorable ground conditions such as soft clay and/or liquefiable sand using ground improvement technique (Yamashita et al., 2011a; Yamashita et al., 2011b; Yamashita et al. 2013). Grid type ground improvement using the Deep Mixing Method has been applied to sandy ground as a countermeasure of liquefaction to increase liquefaction resistance of unstabilized soil left in the grid walls where its shear deformation during seismic motion is reduced by the confinement effect of the grid walls (Kitazume, 2013). The high applicability of the method was demonstrated in the 1995 Hyogoken-Nambu earthquake and the 2011 off the Pacific coast of Tohoku Earthquake (Tokimatsu et al., 1996; Uchida et al., 2012a; Uchida et al., 2012b).This paper offers a case history of piled raft foundation in soft ground supporting a twelve-story building in Tokyo. To increase bearing capacity of the soft soil as well as a countermeasure of liquefaction, grid-form deep cement mixing walls (DMWs) were employed with the piled raft. First, the results of long-term field monitoring on the settlement and the load sharing among the piles, the DMWs and the unstabilized soil are briefly described. Next, to clarify the contribution of the DMWs to bearing the structure load, the foundation behavior is simulated using a three-dimensional finite element model, and then the results of the numerical simulation are discussed."

Jan 1, 2015

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By P J. Terbrugge

The concept of vertical pit mining has been developed as an alternative mining method for the exploitation from surface of small, vertical or near-vertical, massive orebodies down to depths of some 200 m, where ore extraction from conventional open pit excavations is rendered uneconomic due to high associated waste:ore mining ratio. Systematic lateral support maintains vertical pit sides, thereby minimising waste mining volumes. Stability analysis techniques have been developed for design of this lateral support, with the support quantum, primarily comprising long cable anchors, dependent upon country rock strength characteristics and pit configuration. Where the cost of support is less than the cost of the comparable conventional pit waste excavation, vertical pit mining becomes an economically viable alternative, additionally providing the benefit of reduced environmental impact and rehabilitation requirements for the mining area. The technique has been successfully applied for the mining of a chrome deposit in Zimbabwe to an 80 m depth, believed to be unique in the world, and a full feasibilty study for a 3000 m2 diamond pipe has been carried out for mining to 200 m depth.

Jan 1, 2000

By J. D. Scott

This paper consists of a review of the development and application of spherical charge blasting at Inco Metals Company. Topics will include the Livingston Strain Equation, the field data required for its use in full scale operation, the type of ground in which mining has been carried out, explosives in use and their characteristics and finally, an overview of actual production applications. These applications include Primary Stope Mining, Secondary Mining Against Fill, Mining a Faulted Ore Zone and Drop Raise Blasting. INTRODUCTION Crater blasting in itself has been in use for over twenty years, but only recently has the technique been combined with a spherical size charge to form the Vertical Retreat Mining Method. This article endeavours to put the Livingston Strain Equation in a practical light, to describe several actual hard rock applications, and the results achieved in each case. THE LIVINGSTON STRAIN ENERGY EQUATION C.W. Livingston put forward the following equation as a standard means of determining the optimum burden required for full crater production blasting. The constant "E" is included in an attempt to recognize secondary breakage caused by strain waves.

Jan 1, 1981

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By Walter K. (Cory) Conrad

Two pumping tests in the Chilson Member of the lower Lakota Formation were completed at nearly the same location in 1979 and 2008. The 1979 test consisted of a pumping well and several surrounding observation wells penetrating the full 55-m thickness of the aquifer. The 2008 test consisted of a pumping well and three surrounding observation wells screened over 10 m in one of the known uranium ore horizons in the lower portion of the Lakota penetrated only about 3 meters of the more than 55-m thick lower Lakota aquifer. The average transmissivity and storativity values determined from the 1979 tests were 17.6 m2/day and 1.8 x 10-4, respectively. Comparing median transmissivity of 13.9 m2/day and storativity of 1.2 x 10-4 determined in the 2008 test to the 1979 test, the new aquifer parameters for the lower Lakota are respectively about 80 and 70 percent of the 1979 results. Because transmissivity and storativity depend on aquifer thickness, comparing the results suggests that there may be some scaling effect between the tests due to the differing lengths of screened intervals. However, the effect cannot be predicted by calculations such as relative screen lengths or open intervals to the formation, or sandstone versus shale thicknesses on geophysical logs. The scaling effect is attributed to partial disconnection between the lower and upper portions of the Lakota Formation aquifer by locally continuous shale interbeds. Suggestions to resolve this scaling issue are presented.

Aug 1, 2010

By L. F. Bishop

THE ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square-sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill fs a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various meth: ods in use for the second six months of 1944 are shown in Table I. [ ] This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1945

By D. A. Payne

Large excavations, such as Iongwall panels, result in extensive vertical stress redistribution in the surrounding strata. The large abutment stresses developed may produce damage to pre-existing or planned excavations in the same seam or in seams above and below the workings. Knowledge of the magnitude and location of these stresses is therefore important in the design of mine openings; pillar sizes for panel and pillar layouts, roof supports in longwall gateroads and workings over or above pre-existing or planned extraction in adjacent seams. In an attempt to reduce costs, the Cape Breton Development Corporation (CBDC), a Federal Crown Corporation responsible for operating two retreat longwall coal mines, examined the potential for either interpanel barrier pillar width reduction or entire pillar elimination by the adoption of dual life gateroads for the longwall panels. In order to assess the potential for reduced interpanel barrier widths or total elimination, an investigation of the redistribution of vertical stresses around longwall panels in the Sydney Coalfield was established. The study was conducted jointly by the Cape Breton Coal Research Laboratory (CBCRL), of CANMET (a division of Natural Resources Canada) and the Denver Research Center (DRC) of the United States Bureau of Mines. The program included monitoring of vertical stress changes around longwall panels and gateroad behaviour in two seams. USBM-style hydraulic borehole pressure cells connected to chart recorders for continuous monitoring were deployed at four sites, two at Lingan Colliery and two at Phalen Colliery. This report describes the investigations conducted at Phalen Colliery. Contoured plots of stress redistribution around two sites are presented.

Jan 1, 1995

By A. C. Stevenson

THE hoisting equipment selected for use at the Hecla mine in 1907 was one of the first Ilgner type Ward-Leonard controlled hoists put into ser- vice. Development of the Hecla below the 2000-ft. level, which is the ultimate depth of the old equipment, and the additional service required by the "Star," necessitated additional hoisting capacity. It will be our endeavor to give j70u a brief summary of the engineering which determined the selection of the new equipment. The engineer in making his decision as to size, speed, etc., must .make a duty study approximating as closely &s possible the actual opePating conditions which will eventually result. Primarily, it is necessary to know what work must be done. The amount of material which must be hoisted under the maximum condition, as well as its distribution from the various levels of the mine was carefully studied by the mining engineering department, as the ore reserves, their relative-position and the probable method of working them had to be considered. The final figures reached, taking into consideration four different operating conditions, were, in tons per day, as follows:

Jan 1, 1930

By Charles E. Weaver

A core from the La Camelia attapulgite mine in north Florida was studied in detail to determine the detailed vertical variability and the relations of the various parameters. The structural, textural, mineralogical and chemical data indicate there are two major depositional cycles represented within the minable interval. The sediments deposited during the two cycle differ in detail but in general are similar. The environments of deposition grade from shallow marine to lagoonal to tidal flat to marsh. The sedimentary structure (lamination, burrows, pebble conglomerate), mineralogy (attapulgite, montmorillonite, sepiolite, dolomite, calcite) chemistry (Al, Mg, Fe) are closely related to each other and their nature is determined by the depositional environments. Most of the clay minerals and carbonate minerals are authigenic and are therefore particularly sensitive to environmental differences. The variability and environmental features seen in this core are characteristic of the sediments in the general attapulgite mining area. A detailed understanding of the relationships discussed should be of value in prospecting, mining and processing.

Jan 1, 1972