Search Documents

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By Anupam Madhukar

The essence of an atomistic unified kinetic model of strained thin film growth and defect initiation is presented along with a comparison of its consequences obtained from computer simulations with experiments. Within the competing kinetics of a strain dependent activated incorporation of atoms and an asymmetry between upwards and downwards inter-layer migration, the model provides a consistent description of 2D versus 3D morphology evolution accompanied by the appearance of surface vacancies and steps at no energy cost. The correlated migration of these precursor defects offers an atomistic mechanism for the emergence of surface half-loops from the growth front (thus accounting for configurational and thermal entropy) governed by activation energies closer to their correlated motion under the evolving strain fields and thus substantially less than those calculated with respect to the perfect crystal as the reference state. The essential mechano-chemical nature of the problem is compared and contrasted with the historical literature of such phenomenon as precipitation hardening and sintering in metallic and ceramic composites.

Jan 1, 1994

By D. G. Tisdale, W. Curlook, J. M. Toguri

"In this study, the vapour phase reduction of titanium tetrachloride conforms to the traditional Kroll chemistry, but employs argon as an inert carrier gas and requires a higher reaction temperature of 1150°C to 1250°C. A vapour phase reaction is advantageous because titanium is the only condensed phase present, and the metal can be collected free of magnesium or magnesium chloride, in marked contrast to the titanium sponge produced by the conventional Kroll process. The yield of metallic titanium from the reaction was determined as magnesium additions ranged from 36% to 168% of the stoichiometric requirement. Yields of over 99% were obtained when an excess of magnesium was present. Although the collection efficiency was low, metallic titanium was collected at the reaction site, where all other species were present as vapours. Magnesium and chlorine concentrations in the collected titanium were less than 0.3%.IntroductionA proposed method (Curlook, 1987) for titanium production has been investigated as an alternative to the conventional Kroll process (Kroll, 1940). The advantages of the new process include a simplified means of recovering the product metal, and a potential for lower overall energy consumption and greater product purity. A higher reaction temperature for the reduction of titanium tetrachloride results in a vapour phase reaction, rather than the conventional liquid phase reaction. This is the major conceptual difference between the proposed and the established (Kroll) processes.This study focussed on optimization of the process chemistry and briefly examined the issue of product deposition and collection. The reduction of titanium tetrachloride with magnesium, to produce metallic titanium and gaseous magnesium chloride:"

Jan 1, 1997

By E. H. Baker

Vapour pressures of sulphur have been measured over the temperature range 340-1039°C by means of boiling-point measurements, an internally heated pressure vessel being employed with argon as the pressure medium. The results are expressed satisfactorily by a four-term pressure-temperature relation. At the cited critical temperature of 1040°C the calculated critical pressure is 204 atm. From the pressure-temperature relation and available thermal data for the vapour, the approximate composition of the saturated vapour in terms of the various molecular species has been derived for the critical point

Dec 1, 1971

In September 2003, a test was conducted to see if a115-mm- (4.5-in.-) diam Mocap Vari-Stem blasthole plug could improve the pattern of explosives using different top stemming material. The test took place at the J.S. Faulkroad and Sonsstone quarry in McCalisterville, PA. The test consisted of a production stone blast. Half of the holes were stemmed with standard crushed stone. Two-thirds of the remaining half were stemmed with Vari-Stem plugs and crushed stone. And the remaining one-third of the second 50 percent was stemmed with Vari-Stem plugs and only drill cuttings.

Jan 1, 2004

By José Luis Vitteri

Dado que se generan largas colas de los camiones mineros en los puntos de carga, es necesario revisar las causas principales que la originan. Entre estas tenemos: el desconocimiento de la variabilidad y sus efectos nocivos y la aceptación de que el mínimo costo de operación se obtiene con la mayor utilización de la excavadora. En este sentido, el presente texto describe el manejo de la variabilidad en los procesos de carguío y transporte con equipos pesados a través del estudio de sus causas, de forma que la única manera correcta de reducir el perjuicio de la variabilidad en el transporte, es manipulando la frecuencia inicial de los camiones.

Oct 1, 2013

By C. L. Van Dover

Organisms living at hydrothermal vents are adapted to catastrophic disturbances in their environment caused by processes such as tectonic activity and mineralization that shift the locus of fluid flux and volcanic eruptions that pave over active systems and reset the hydrothermal cycle. The scientific community appreciates this risk of natural, local loss of species, genetic, and habitat diversity. The risks of more profound loss of diversity and ecosystem function and health as a consequence of additive commercial activities in hydrothermal systems are unknown, and are not the same across all deep-sea hydrothermal systems. Vent communities differ from one ocean basin to another, as do the geological settings and geochemical dynamics of vent systems. Communities on the East Pacific Rise represent one end-member in the catalog of hydrothermal vent communities. In these systems, the life cycle of a hydrothermal field is on approximately the same time scale as the lifespan of the species that live there. From studies of the 1991 and subsequent eruptions at 9N on the East Pacific Rise, we understand the rapidity with which new vents are colonized when nearby brood stocks are available to repopulate the system. Almost instantaneously, microbial biofilms and mats form, followed quickly by invasion of mobile opportunistic organisms (especially crabs, copepods). In a matter of a few months, a predictable succession of sessile organisms recruits, grows, and reproduces. Within two to three years, the system returns to levels of species diversity that begin to match those of the pre-eruption condition. Vents on the Mid-Atlantic Ridge (MAR) represent a different end-member, with catastrophic disturbance rare relative to the life span of the organisms that make up the bulk of the biomass. We have no experience with an eruptive event or other major transformation of venting activity on the MAR and thus have no knowledge or insight regarding the time it would take for the biological diversity to return to pre-cataclysmic levels.

Jan 1, 2008

By T Baumgartl, D R. Mulligan, D Doley, A Schneider

In arid and semi-arid areas evapotranspiration (ET) cover systems are often used to mitigate contaminated seepage from hazardous mine waste into the adjacent environment. The theory of ET covers is based on the water balance equation with the aim of minimising seepage. While cover systems are commonly trialled, the influences of variability in climate and cover structure on water balance equation parameters are seldom investigated.Water balance equation parameters and their variability were analysed for two ET cover trials constructed from benign waste rock in semi-arid Australia. Seasonal and inter-annual variations in rainfall critically influence cover performance. For successful cover system operation, the average return periods for higher than average rainfall should be taken into account. In addition, failure of ET covers has a higher probability in areas with marked rainfall seasonality. Water holding capacity and plant available water content are low in covers constructed from waste rock. Changes in water holding capacity due to variation in particle size distribution are likely and critically influence cover performance. The application of topsoil can be beneficial for water ingress control through run-off, but a balance has to be struck between run-off, erosion and plant available water. Changes in vegetation composition only influence evapotranspiration water losses at plant coverage exceeding 50 per cent, which is unrealistic in semi-arid areas. This study showed that the capacity of ET cover systems to hold and dispose of received rainfall is often lower than assumed by industry practitioners. Furthermore, in order to improve reliability of long term cover performance, the variability of rainfall and water holding capacity of the cover has to be included in water balance models.CITATION:Schneider, A, Baumgartl, T, Doley, D and Mulligan, D R, 2012. Variability in parameters of the water balance equation and their influence on evapotranspiration cover performance, in Proceedings Life-of-Mine 2012 , pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Shahzad Moosa, John M. Pitt

Statistical variability in rock strength can be evaluated by rapid, inexpensive ultrasonic pulse velocity measurements, an important consideration since rational probabilistic design in rock is often hampered by the cost of obtaining sufficient strength data. Experimental ultrasonic pulse velocity measurements on a set of 96 limestone specimens showed two distinct statistical populations. Both populations followed Weibull distributions, with flexural strength distributions paralleling pulse velocity distributions. Thus, experimental results suggest that strength variability may be predicted from a few rationally selected strength measurements and several ultrasonic tests. The correspondence between strength and velocity may then be used to develop an experimental transformation function, allowing the development of a statistical distribution function for strength based on the known statistics of velocity. Comparison of experimental groups with full sets of corresponding strength1 velocity data showed the technique offers a fairly accurate description of the statistics of strength.

Jan 1, 1986

By D. G. Krige

Recent publications have demonstrated the important role that can be played by a priori information of the grade levels, variability, and spatial patterns in adjacent or nearby areas in improving the quality of grade estimates for virgin or sparsely drilled areas. A research project was therefore conducted involving the collection and analysis of extensive sampling and borehole data from 7 reefs on some 30 Witwatersrand mines. This paper shows that the 'equivalent' log variance for the two-parameter lognormal model provides a good basis for the study and comparison of the levels and behaviour of relative variances. The trends of these against the corresponding log areas were found to form distinctive patterns, which are useful for these purposes. The patterns for the Basal, Vaal, Carbon Leader, and Main Reef Series form a reasonably close group, whereas those for the V.C.R.(particularly where the facies are mixed), B Reef, and Kimberley-Elsburg Reefs (particularly for narrow channel widths) do not always conform. The patterns shown by underground chip samples are also compared with those obtained from borehole cores. It is shown how this information can be used to improve the borehole valuation of new mines and of virgin areas in existing mines.

Jan 1, 1993

Differences in the assay results of replicate samples engender doubts on the reliability of ore sampling and of assaying procedures. An analysis of variance is a technique to estimate the variability at each level of the procedures. In an example, the variability of one-metre core samples was far greater than that of the assaying technique.

Jan 1, 1976

By S C. Dominy

The gravity recoverable gold (GRG) parameter reflects liberated gold or gold-dominated composite particles that can be recovered by gravity separation. Recoveries depend upon mineralogy, in situ particle size and the comminution and extraction method used. Any ore bearing >15 per cent of gold greater than 50 ¦m in size is likely to have a GRG component. The principal characterisation methodology applied is the three-stage GRG (3GRG) test, based on a 40 kg to 100 kg sample. An alternative is the single-stage GRG test (SGRG), which is generally based on a 20 kg sample. Experience has shown that GRG values can vary throughout an orebody, particularly within different grade and/or mineralogical domains. Test programs must consider sample frequency and mass. This study demonstrates the variability of GRG results based on different sample masses. Consecutive underground faces on a coarse-gold dominated quartz vein were sampled taking five different masses from each. Each sample was processed using a SGRG approach. Subsequently, each development round was batched through a small gravity production plant. The results show that the small samples understate the plant GRG and show inter-sample variability. Large samples show less variability and a SGRG closer to the plant GRG. A high SGRG broadly correlates to higher gold grades, more coarse gold and larger gold particles. These results are intuitively correct, but indicate the likely challenges of sampling for gold recovery in heterogeneous systems.CITATION:Dominy, S C, 2013. Variability of gravity recoverable gold values in relation to test sample size, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 293-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By H. Rosen

The pump is the heart of most industrial and mining plants, providing the energy to separate valuable minerals from process feed. The actual effect of the pump, both in terms of production costs and overall process efficiency, is often assumed or misunderstood by engineers due to insufficient pump performance data. Pump performance can be understood and corrected, where required, through continuous performance monitoring, leading to dramatic improvements in both pump life cycle costs and system efficiencies. The performance of every pumping application is subject to variation and the main contributing factors are as follows: ?Unavoidable deviations from pump supplier curves ?Pump wear ?Pump curve derating factors for slurry pumping ?System curve variation ?Deviation from basic principles of centrifugal pump operation. These are discussed in detail through case studies and the author?s personal experiences. This paper shows ways to minimize the effect of these variations, thereby reducing performance loss and preventing damage to the pump. The paper discusses the benefits of efficient pump operation, the requirements of pump performance monitoring, and its practical application to pump operation in the slurry and water environments. The cost of remedial actions is explored and compared against the savings in both power and plant reliability, resulting in a reduced life cycle cost of the pump.

Jan 1, 2010

By R. T. Grant, C. Bazin, D. Hodouin

It is shown that most of the variation in the results of semi-batch flotation tests is related to the unavoidably stochastic nature of the flotation process. The preparation and analysis of flotation samples and, to some extent, operator error in performing the flotation test procedure are responsible for a small proportion of the observed variability of the calculated flotation performance indices

Jun 17, 1905

The ability to increase and maintain dragline productivity is a key mine driver for the Coal Creek Mine. The Coal Creek Mine is owned by Arch Coal Inc subsidiary Thunder Basin Coal Company; located near Gillette, WY. Coal Creek Mine overburden stripping is primarily accomplished by a BE-1570W walking dragline in combination with cast blasting and dozer assist for bench preparation. The two main variables impacting dragline performance are maintenance reliability and operator skill levels. The mine?s most recent process improvement efforts have focused on its most valuable asset - the operator. Various techniques have been used to reduce variability in the dragline operator?s digging performance. Utilization and communication of operator performance data, statistics, and video reviews have been of great value towards achieving this goal. Operators are given a chance to critique operational tendencies from a third-person point of view, and are also presented statistical feedback to support observations. From these sessions, operators gain knowledge as to what portions of the dig cycle can be improved in order to reduce cycle time and increase productivity. BACKGROUND The BE-1570W walking dragline was commissioned at Coal Creek in November 2006 after relocating from Arch of Wyoming located in southeast Wyoming. The first two years of operation the machine was performing simple side cast stripping due to the low ratio. Coal Creek Mine is a multiple seam operation with overburden thickness ranging from 24 to 140 feet. Early in 2009 the ratio increased to the point where transitioning to cast blast/extended bench stripping was necessary. The current mining conditions consist of a mixture of both stripping styles where the ratio allows. The dragline crews running the machine consist of a mixture of experience levels ranging from 30+ years to only a few years. It has been in this digging environment and slightly inexperienced personnel that the focus has been set for improvement in dragline performance.

Jan 1, 2011

By M. Bergerman

Sossego was the first Vale SAG mill operation to process copper-gold ore. It is located in Para state, south east of Amazon region in Brazil. The comminution circuit was designed to treat 41 000 metric tons per day comprising primary crushing, one 11.6 m SAG mill operating in closed configuration with cone crushers, followed by two 6.7 ball mills. In the first three years of continuous operation Vale investigated alternatives for obtained improved performance of the circuit by investigating operating conditions, mainly focusing on SAG mill. A number of actions were then implemented, which resulted in significant increase in overall production. Vale then decided to further assess the performance of the comminution circuit as a function of ore characteristics. A comprehensive ore characterization program was then conducted, together with the calibration of mathematical models on the basis of surveys carried out at the industrial circuit. The simulator was then used to predict the production level associated to each ore type, as well as to establish the optimized circuit configuration and tailored operating conditions. The ongoing validation program is planned to consolidate the selected strategy, as well as showing the benefits in adopting such indices in mine planning, as opposed to rather simplistic approaches. This paper describes in detail the main aspects of optimizing the industrial circuit performance, as well as the successful method for predicting the production as a function of ore characteristics.

Jan 1, 2014

By D Stow, R Goodridge, K J. Molloy

A range of explosives has been specifically developed for soft ground blasting. These explosives can be used in both wet and dry blasting conditions, range in density from 0.3 - 1.2 g/cc and range in VoD from 2 - 4.5 km/s. This range of explosives has the potential to be tailored to ground type and is predicted to be suitable for a variety of applications which include: blasting in soft to medium overburden, coal blasting, wall control, and low vibration blasting. Trials have been conducted in several applications with encouraging results. Several cast/throw blasts have been conducted with these products partially replacing either ANFO or Heavy ANFO. The results from the blast have been equivalent in cast (per cent) and at reduced cost per unit volume. These products have also been used in presplit blasting and have again achieved equivalent or better results when compared to conventional presplit blasting at a lower cost per unit volume. This product has also been used in a vibration sensitive area replacing traditional explosive products, and generating excellent fragmentation and digging whilst maintaining vibration limits. This new range of products, NOVALITE, has shown great potential in many applications either reducing cost per unit volume, improving wall quality or improving productivity in environmentally sensitive areas.

Jan 1, 2001

By J. Elderton

"The combination of A C induction motor and flu id coupling, of either the fixed or variable filling type, constitutes a simple, low cost, highly reliable drive unit, with many applications in the mining field.The paper will, however, concentrate on the variable filling fluid coupling in three principal applications-conveyor starting, infinitely variable speed control for slurry and slimes pumping and dewatering pumps for deep mines. Fluid couplings can be used with standard or custom-built control gear equipment, ranging from the most simple, time-based open loop types, to those having the latest microprocessor techniques.IntroductionThe first industrial applications of fluid couplings included their use in the mining field as hydraulic slip regulators for flywheel generating sets. These installations, usually rated at around 1700 to 2500 hp, were located at mine shafts where the electrical grid transmission lines were not strong enough to cater for the peak power demands of the cage winding cycle. In Canada, the first two significant examples of variable filling fluid couplings for mining were on conveyor drives, at Steep Rock Mines Limited, closely followed by the major iron ore handling term inal on the St. Lawrence River at Sept-Iles. Successful and reliable operat ion of the fluid couplings at these two sites set the pattern for use on many subsequent mining projects throughout the Canadian Continent."

Jan 1, 1986

By Cheryl L. Allen

The power required to operate a ventilation system can be 25% to 50% of the total energy requirements of a mine. In an effort to reduce energy consumption, initiatives are being introduced at Vale Inco to increase the efficiency of ventilation systems with the objective of decreasing energy usage. One energy conservation measure being introduced is the use of variable frequency drive (VFD) technology for fan motor control. Advancement in technology is making VFD applications more of a standard in industry. The benefits include improved operating performance and system control, reduction in current peak demand, and optimized power usage. This paper describes the application of VFDs for main and auxiliary mine fans; and associated potential energy savings.

May 1, 2009