Search Documents

By W. M. Aubrey

The use of solid fuel in shaft furnaces to indurate iron ore pellets was originally considered a necessary evil, which the industry worked long and hard to eliminate. Since then changes have taken place in furnace design and operating practices that have led us to our suggestion that solid fuel additions could again be used. In essence, what has happened is that the developments which made it possible to operate without solid fuel have also created new operating conditions favorable to the effective use of solid fuel. Because these new conditions* were brought about in part by the desire to eliminate solid fuel and because the development was a gradual one, the industry failed to reassess its position and for years neglected the possibility of returning to solid fuel.

Jan 1, 1967

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FexAs2O2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS203 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FeAsyO2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS2O3 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By Daniel K. Kim

The charge for the copper refinery is a mixture of anodes produced at San Manuel from BHP source concentrate and copper purchased from external sources. Control of unwanted impurities in the tankhouse - is very important and beneficial. Currently available removal/recovery technologies were reviewed for the control of bismuth and antimony levels in the electrolyte. Recent studies have focused on solvent extraction (SX) technology and generated successful results for the removal and subsequent recovery of bismuth and antimony. The SX system employs the reagent, ACORGA SBX-50, in conjunction with a patented high chloride stripping system. The latter enables recycle of the eluant, avoiding the high costs associated with conventional systems, such as regeneration of resin. Concerns over potential transfer of organics and chloride ion to the electrolyte were readily addressed, solved and demonstrated using conventional, established technology. This paper describes the benefits of electrolyte purification, the flexibility afforded by the SX system, the operational practices necessary for maintaining adequate control of bismuth and antimony impurities in the electrorefining environment and possibilities for future development /exploitation of the Zeneca SX system at the San Manuel refinery.

Jan 1, 1998

By Charles E. Mongan

The problem of roof control in the coal-mining industry is of major importance inasmuch as 65 percent of all coal-mine fatalities result from falls of roof, face, or ribs. The Health and Safety Research and Testing Center of the Federal Bureau of Mines at Pittsburgh, Pa., is engaged in several programs directed toward increasing safety in coal mining. The Roof Control Research Group has 4 programs aimed at reducing roof fall accidents. One of these programs is the use of sonic techniques to explore mine roof strata.

Jan 1, 1961

By V. H. Gottschalk

SEVERAL years ago a group in the metallurgical division of the U. S. Bureau of Mines began a study of the application of new developments in physics to metallurgical problems'. Among these developments were the extensions of what may be termed by analogy the "sound spectrum." Electromagnetic waves, from X-rays to radio waves, have been quite thoroughly explored for metallurgical use, but the sound spectrum, extending from low-frequency vibrations involved in certain types of metal failure by fatigue through the range of audible sound to inaudible vibrations having frequencies of many kilocycles, has had only meager consideration from metallurgists. Because of the general interest in the process recently demonstrated by St. Clair3 for flocculating smoke by means of sound waves, this article is written to point out possible applications of sound and supersonic (ultrasonic) waves in the metallurgical industry.

Jan 1, 1937

By P. J. Nel, A. Täuber

SYNOPSIS A method is described whereby finely ground glassy granulated blastfurnace slag mixed with small quantities of clay, whiting and quartz has been used for making ceramic tiles in the laboratory. The tiles were semi-dry pressed and devitrification as well as sintering occurred during firing. The properties of the resulting product compared favourably in many respects with ordinary ceramic flooring materials.

By M. M. Carpenter

Specialty chemicals are widely used in the industrial minerals process industry for many different purposes including beneficiation, filtration, flocculation, dispersion and biological control. Optimal use of such chemicals can confer benefits both in terms of cost efficiency and end product attributes. In this paper we will review recent progress in the fundamental understanding of mineral additive interactions and present data which show how optimization can lead to improved products.

Jan 1, 1999

By John G. Tate, George W. Nicolson, James L. Bruce

FOR more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.1 From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. DESCRIPTION OF ORE BODIES The shape of the ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions, extending from unknown depths below the bottom level at elevation 250 ft below sea level, to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the ore body extended to surface and was mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upperside of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and clay sedimentaries of Miocene and later age. The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-stained by the descending meteoric waters. It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pct Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pct. On the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. Some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. This probably can

Jan 1, 1947

By T. Brady, R. Langston, J. C. Johnson, H. Kirsten

An experiment is described in which instrumented rock bolts were used to measure strain in the rock mass during drift development at the Stillwater Mine, Nye, Montana, USA. Two strain-gauged rock bolts were grouted into the middle of the rib next to the face. The drift was excavated in three advances, each one-half drift wide. Strains were recorded hourly by a data logger. Results show that the average change in axial bolt strain for the first and second advance was about the same and that there was almost no change in strain after the third advance. Bending strain was observed 19 cm from the head of the bolt.

By Malte J. M. Gurgel, Axel Preusse

The planning, construction, and monitoring of underground storage facilities is a key factor in meeting upcoming challenges as part of the energy transition from fossil fuels to renewables. Therefore, the many years of knowledge and expertise in ground control gained from coal mining are highly valuable for new mining and storage operations. For such applications, our previous work examined cavity registration, combining structure from motion and LiDAR through a case study in a former lead ore mine. Building on this, the results of this recent case study are discussed regarding the possible application in sites for nuclear waste disposal in Germany including a view on the situation in the United States. Photogrammetric methods are particularly suitable as part of long-term monitoring, which relies on both precise survey results and a large variety of detailed visualization. In order to gain a better understanding of the resulting application potential for holistic monitoring, both existing repositories sites in Germany and ones yet to be found are examined. This search and selection process for high-level nuclear waste disposal is studied in detail together with rules resulting from the (German) mining law, regulations, and other guidelines. Hereby, key requirements of photogrammetric products like oriented images, point clouds, and three-dimensional (3- D) models are identified for different case studies. The findings on accuracy and integrity of the generated models are not only of interest for future repository sites or underground pumped storage power plants, but also offers various possibilities for underground mining of coal and other commodities.

Jul 1, 2023

By P. W. Conrad, C. Todd, N. West, R. Kramer

"Surface subsidence caused by both underground room-and-pillar mining operations and solution mining operations have each been studied separately, but never combined. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. PROJECT BACKGROUND FMC Minerals (FMC) has increased the production of trona from its Westvaco Mine near Green River, Wyoming, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 1,600 feet. Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed. The location from which the trona was removed and the size of the cavern created by the solution mining operations is important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found that would allow for the use of surface subsidence measurements to estimate the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find a relationship between the measured subsidence and the solution mining activities. The project attempted to model the relationship between the measured subsidence and the solution cavern using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI), to determine the program’s usefulness for locating and developing the cavern created by solution mining activities. The project also attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The data used in this study were collected over a seven year period, 2008 through 2014."

Jan 1, 2016

By P. W. Conrad, C. Todd, N. A. Degerstrom, N. West, R. Kramer

"Surface subsidence caused by underground room-and-pillar mining operations and by solution mining operations have been studied separately but never in combination. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Using Salt_Subsid, a subsidence software package from the Solution Mining Research Institute, and ArcGIS, Esri's mapping platform, researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. Project backgroundFMC Minerals has increased the production of trona from its Westvaco Mine near Green River, WY, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 488 m (1,600 ft). Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed.The location from which the trona is removed and the size of the cavern created by the solution mining operations are important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found between surface subsidence measurements and the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find relationships between the measured subsidence and the solution mining activities. The project attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The project attempted to model the relationship between the measured surface subsidence and solution mining production using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI, Clarks Summit, PA) to estimate the location, size and shape of the solution mining cavern. This study would determine the program’s usefulness for locating and developing the cavern created by secondary solution mining activities. The subsidence and production data sets used in this study were collected over a seven-year period from 2008 through 2014."

Jan 4, 2018

By M. D. Mwema

Copper oxide ores deposits in the Katanga province of the Democratic Republic of Congo (DRC) contain at variable level cobalt oxide minerals. In contrast to copper oxide minerals which readily dissolve in the sulphuric acid solution, the cobalt oxide bearings are difficult to dissolve, especially if cobalt is present in the third oxidation state (Co2O3). This species become soluble after reduction of Co+3in Co+2. In practice, the use of reducing agent is therefore necessary in order to transform the insoluble minerals into soluble cobalt sulphate species. The following reducing agents are currently used at the Shituru plant: ferrous ions, which are present in leach solutions, pulverised copper or sodium meta bisulphite (MBS). Due to the high consumption of reducing agents (0,8 t MBS/t of solubilized Co; 1,2 t Cu/t-Co), cobalt production is expensive. The use of sulphur dioxide as reducing agent was then investigated in order to reduce operating cost. This reagent also presents the advantage of sulphuric acid production during the leaching process. It has been added in the leaching vessel (tank). From the laboratory and industrial tests, selective leaching of cobalt (78%) has been performed. The cobalt leaching kinetic depend on sulphur dioxide dosage. Dissolution of copper, iron and manganese remained very low. No emanation of SO2 gas was observed during the process.

Jan 1, 2002

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By J. W. Wilson, Y. P. Wang, M. H. Erten

The use of water is still the most effective and economical means for dust control in underground coal mines today along with dilution by the ventilation current. Studies have shown that the dust capturing capacity of water is a result of a balance of many intermolecular forces. Surfactants are known to reduce such forces by affecting both the surface tension of the liquid and its interfacial tension against a solid. Surfactants can be added to the water sprays to facilitate the dust capturing capacity. A laboratory scale model has been developed in which surfactants were added to the spraying water and preliminary data indicates positive results.

Jan 1, 1991

By Rebecca S. Stanevich

BACKGROUND Diesel exhaust is an animal carcinogen, although evidence of the carcinogenicity in humans is "limited". (World Health Org. , 1989) Of the eight cohort studies in the 19808, five found an increased risk for lung cancer among workers who may have been exposed to diesel exhaust (RR from 1.3-1.5, SMR from 101-132). (Howe, et al., 1983) Only two studies accounted for smoking indirectly. Of the ten case-control studies in the 1980's, eight reported increased risk of lung cancer among those populations purportedly exposed to diesel exhaust. (Benhamou, et al. , 1988) All but one of these adjusted for smoking and other occupational exposures. The odds ratios ranged from 1.2 to 2.1. In two of these studies, miners experienced a two to three fold risk. (Benhamou, et al., 1988) Bladder cancer has also been linked to diesel exhaust in cohort and case-control studies. Excesses of approximately 50% were observed among truck drivers in studies by NCI. (Hoar, et al., 1985) In the National Bladder Cancer Study, risks for truck drivers rose with duration of employment. A study by NIOSH in Ohio also found an excess of bladder cancer among truck drivers, particularly among those with 20 or more years of employment. (Steenland, et al, 1987) Despite the large number of studies in which the relation between diesel exhaust exposure and lung cancer has been examined, exposure to diesel exhaust has been quantitatively estimated only in the studies of railroad workers and truck drivers. (Woskie, et al., 1988) The excess lung cancer risk experienced by workers in these two occupational groups was modest, ranging from 40 to 90% for those with long-term employment. However, diesel exhaust exposure among railroad workers and truck drivers is lower than that seen among miners. Several markers of diesel exhaust have been utilized in these studies. Diesel exhaust is a complex mixture of particulates, vapors and gases. One group of these gases, the nitrogen oxides, react with polynuclear aromatic hydrocarbons, forming mutagenic and possible carcinogenic nitrated derivatives. (World Health Organization, 1989) For this reason, and because it is easy to measure and analyze, NO, was frequently used as a marker of diesel exhaust exposure. As part of the Garshick (Garshick, et al., 1988) study of railroad workers, Woskie measured NO, exposures of 477 railroad workers. (Woskie, et al., 1988) Geometric mean exposures of 13 job groups ranged from 12 to 80 ppb. In a New Mexico potash mine, (Attfield, et al. , 1982) exposures of from 100 to 3300 ppb nitrogen dioxide

Jan 1, 1992

By L. A. Rose

AMONG the half-dozen major research search projects now being conducted at the Michigan College of Minim, and Technology under the terms of an FERA grant, an important one relates to the use of suspensions in ore dressing. The study has resulted from the constantly widening industrial use of metals and minerals. The modest demands of a few decades ago for these minerals could be easily met from richer deposits. Now, at least in some localities, the richer deposits are nearing exhaustion. Furthermore, advances in the industrial arts and the competition of other minerals and metals have changed the specifications of materials needed by the manufacturers. Premiums and penalties enter into the sale value. Hence, to meet the requirements for amount and quality, washing and other ore-dress-

Jan 1, 1935

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. It was shown that this selectivity was the result of preferential adsorption of the polymer on the surface of the iron sulfide minerals. The different types of interaction between the functional group on the polymers and the sulfide mineral surfaces could explain the trends observed in the flotation results.

Jan 1, 2003

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. These results are significant considering the differences in ore type, proportion and type of iron sulfide minerals present, and grinding medium used in this study.

Jan 1, 2003