Search Documents

By Donald W. Frommer

For many years the Bureau of Mines has been con- ducting comprehensive iron ore research programs with the objective of increasing domestic supplies and divising techniques that would enable profitable exploitation of low-grade and complex domestic iron-mineral deposits. Since 1962, much of the Bureau's flotation research at Minneapolis has been concerned with studies on the treatment of low-grade hematitic-goethitic jaspers of the Marquette range, Mich. Ores from Michigan require grinding to substantially minus 400-mesh for liberation that will permit production of quality concentrates. With such fine grinding, diminished flotation effectiveness can be expected because of slime interference. The word "slime" is an ambiguous term. Taggart states "Slimes in an ore pulp are loosely defined as the fine fraction that overflows a desanding separator. . ."

Jan 4, 1964

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that contains between 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

This paper sets out to discuss some of the more common forms of geological data abuse in project development. The paper illustrates various types of abuse and the reasons behind that misuse of data. This paper is only a brief introduction to a very large subject.

Jan 1, 1983

By Richard E. Ellwanger

Methods of utilizing flocculants as settling and filter aids for mineral processing slurries are reviewed. Broad chemical classifications and techniques for proper dilution, multiple addition, and combination treatments are discussed. A variety of custom built and commercially available systems for make up and delivery of flocculants to the application points are in use through- out the mining industry. Those concepts which, in the author's opinion, are particularly important to the successful make up and use of flocculants are presented in relationship to the available make up and feed systems. Actual industrial applications are included in the presentation.

Jan 1, 1980

By Richard E. Ellwanger

Methods of utilizing flocculents as settling and filter aids for mineral processing slurries are reviewed. Broad chemical classifications and techniques for proper dilution, multiple addition, and combination treatments are discussed. A variety of custom built and commercially available systems for makeup and delivery of flocculents to the application points are in use throughout the mining industry. Those concepts which, in the author's opinion, are particularly important to the successful makeup and we of flocculants are presented in relationship to the available makeup and feed systems. Actual industrial applications are included in the presentation.

Jan 1, 1982

By Robert Lewis

Some recent experiments in the use of compressed air for rock drills at higher than usual pressures, up to 150 lb. per sq. in., emphasize the importance of maintaining the compressed-air system in the best condition if the greatest possible over-all efficiency is to be secured. No claim of high over-all efficiency can be made for the compressed-air system of braking that is used on railroad trains, yet the air brake works effectively. Compressed air is not used efficiently in the rock drill, but no other type of machine drilling is yet a serious competitor of the air-driven rock drill.

Jan 1, 1930

By J. W. C. Wong, S. D. Miller, J. J. Jeffery

Pre-mining identification of acid forming mine and waste materials is of concern to the mining industry because of the potential for the generation of acid mine drainage, acid rock drainage, and soil acidity problems. Accurate identification of acid forming material is essential for developing appropriate waste management strategies to reduce environmental problems related to acid generation from sulphide containing wastes. The acid-base accounting procedure, in its various forms , is commonly used for pre-mining screening of mine and mine waste materials. The procedure is generally effective when used and applied correctly but is prone to incorrect interpretation of results which can have significant financial and environmental implications. This paper examines the acid-base accounting Procedure and the possibility of misuse of this method with special emphasis on the sampling method, the sulphide forms, the acid neutralization capacity, and the interpretation of results. Data from numerous coal, base metal, and gold mining operations are used to illustrate the application of the acid-base account. The data base indicates that overall, approximately 1/3 of all waste generated by mining and mineral processing is potentially acid forming indicating the need for correct identification and management. Problems associated with simple application of 'absolute' acid-base criteria for classifying acid forming material are highlighted and the need for developing site specific or 'relative' criteria is discussed and illustrated by case study.

Jan 1, 1991

By Laird CH

Large quantities of brown coal are excava ted from open cut mines in the Latrobe Valley to fire the base load thermal power stations of the Victorian Electricity System. Most of the coal is removed using bucketwheel excavators which have been modified or specially designed for the conditions encountered. The actual digging efficiency of the bucketwheel excavator is strongly influenced by such factors as wheel speed, slewing speed and tooth design and arrangement. The coal deposit, although not difficult to work, is not uniform and the operation of the machine is influenced by the stability re- quirements of the excavation face.

Jan 1, 1978

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933

By H. P. Reid

PORTLAND cement is manufactured under either of two general proc-esses, the wet or the dry. The raw materials in general consist of limestone, shells, marl, cement rock, clay, shale, blast-furnace slag, etc., so proportioned that when calcined the desired composition will be obtained. In the wet process the combined raw materials are ground to extreme fineness in the presence of water, to a resulting slurry of from 30 to 50 per cent moisture content. The moisture of the slurry may be reduced by thickening or filtering processes for feed to the cement kiln or the slurry may be fed to the kiln with its full percentage of water. The dry process differs from the wet in that the surface moisture of the raw materials is removed prior to grinding. For the drying of these materials heat is required and in most cases is produced by burning of raw fuel either on grates or stokers before the dryers or in suspension in the form of pulverized coal, oil or gaseous fuel. The power required for making the cement is sometimes purchased from outside sources; sometimes it is generated from the heat in the waste gases leaving the cement kilns, or generated at the plants direct from raw fuel. We have, then, as the possible requirements of fuel in the cement industry: (1) fuel for power generation, (2) fuel for drying raw materials, including coal before pulverizing, and (3) fuel for burning the raw materials to cement clinker. There is no essential difference in quality required in fuel for burning the materials by the wet and dry processes.

Jan 1, 1932

By Jonathan Ludlow, Robert A. Jankowksi

Introduction A longwall operator can make few changes to increase output, significantly reduce respirable dust, and decrease power consumption. Reducing drum speed, and thereby cutting with increased pick penetration, is one. This article defines the benefits of deep cutting in terms of reduced dust production and power consumption. It also identifies the practical aspects of high pick penetration in terms of shearer performance and coal loading. Before examining some practical aspects of reducing drum speed and looking at the theoretical background, it is worthwhile to summarize what is meant by high penetration and deep cutting, and what potential benefits and pitfalls may be expected. Deep cutting (in the sense of high penetration rather than wide web) can be defined in one or more of the following ways: • Cutting with an average pick penetration distance higher than that used in the past. • Cutting with a pick penetration higher than the longwall operator would have used if the advantages of deep and slow cutting were not considered. • Cutting with a well-designed shearer drum below 40 rpm. All these definitions are slightly arbitrary. They are given to provide a basis for discussion and to make the point that any move towards deeper, more efficient cutting can result in operational benefits. The benefits of deep cutting appear in many different areas. The most noticeable benefit, provided suitable instruments are available, is the reduction of airborne respirable dust. During an experiment on a longwall in the Pittsburgh seam, a nearly four to one reduction in dust levels was seen when drum speed was halved. Not all studies have shown such a big reduction, but it seems that some benefit is almost always obtained when drum speed is reduced. Production rate and specific power consumption are also affected (in a positive sense) by reducing drum speed or increasing pick penetration. Although these changes may not be as spectacular as those in dust level, they contribute to the economic return of the longwall operation. Similarly, improved washability through fines reduction may have a beneficial economic effect. Cutting with shearer drums operating at lower speeds does have some possible deleterious impacts that an operator should be aware of. For example, cutting reactions - loads imposed on the picks by the coal being cut - will be increased as a deeper cut is used. Steps must, therefore, be taken to ensure the stability of the shearer and provide an adequate haulage effort. These increased cutting reactions also result in higher loads on the power transmission system (gearboxes, ranging arms, pick boxes, etc.) from the shearer motor(s) to the pick tip. These higher loads must be anticipated and provided for with the necessary hardware. In particular, extra haulage power must be provided with low drum speeds, since haulage effort required increases roughly in proportion with pick penetration. Because the drum will be rotating more slowly or will have fewer picks, the load on shearer components will also be more variable. If suitable, robust equipment is not used, this increased vibration will decrease reliability. Benefits of Deep Cutting Lower dust levels, decreased specific power consumption, and improved product washability are the most noticeable benefits of reduced drum speeds. Although the benefits will vary greatly with mining conditions and the type of coal, some examples of what can be expected are described below. Reduced Dust Levels Figure 1 shows principal results of a study on the effects of reduced drum speed conducted on a longwall in the Pittsburgh seam (Ludlow, 1981). This figure shows that average dust production was reduced by about 70% when drum speed was halved. By making some assumptions about such quantities as coal density, it is possible to apply this proportional reduction to the quantity of respirable dust liberated per ton of coal mined. When this is done, two kinds of results are obtained: • At 70 rpm, about 1 g (15 gr) of airborne respirable dust is created for every ton mined (roughly one part per million). At 35 rpm, only 0.28-0.37 g/t (3.9-5.1 gr per st) of coal mined become airborne respirable dust. • At 35 rpm, nearly four times the amount of coal may be mined before the compliance level is exceeded, compared with 70 rpm.

Jan 3, 1984

By G. Deschenes, P. J. H. Prud'homme

A laboratory study was carried out to evaluate the effect of oxygen and lead nitrate on the recovery of gold by cyanidation of a free milling gold ore, which contains 0.4 % copper as chalcopyrite. Efficient gold extraction is achieved only under specific conditions. The recovery of gold was increased from less than 90% to up to 98% by addition of lead nitrate. In the pre-leaching, the kinetics of oxidation of soluble sulphides are not an accurate indication for the length of the treatment. Even though the consumption of cyanide was reduced due to the inhibition of the dissolution of chalcopyrite by increasing additions of lead nitrate, cyanide consumption had to the held above 1.85 kg/t to maintain good recovery of gold. The continued addition of lead nitrate above 300 git had no impact on the recovery of gold. It was also found that the addition of lead nitrate at the start of cyanidation gave the same performance as when added during pre-leaching. The addition of oxygen increased the recovery of gold by 1.5%. The concentration ofNaCN had to be maintained in the range of700 mg/L because of the high concentration of copper in solution. The recovery of gold dropped significantly when the average NaCN concentration fell below 640 mg/L. Application of the findings of the laboratory study at the industrial scale led to improved plant performance.

Jan 1, 1997

By Fred DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force? of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are inter-esting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or, elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determina-tion of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L'Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l'uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l'épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003

By H. Brüggemann

The exploration of deposits generates geological data which are suitable for creating a preliminary tectonic and stratigraphic model. Linked with the topographical map and analysis data from exploration drillings, this information forms a numeric representation of the deposit. The following example demonstrates an expert system which connects chemical quality requirements and quarrying criteria, and develops a quarrying strategy based on the calculated model. Additional constraining factors like process technology, quarrying methods, landscape protection regulations, etc. are included. The goal is to guarantee a long-term, homogeneous material flow from the quarry at acceptable production costs - even in the case of an extraordinarily inhomogeneous deposit. In order to fulfil this requirement it is necessary to consider a large number of rules, criteria and instructions which can be structured as an expert system and programmed with LISP at a comparably low cost. The chosen strategy is not necessarily final, but can be changed any time by altering or varying the framework of conditions. The output consists of a block-working sequence which best satisfies the set requirements for appropriate points of quarry opening.

Jan 1, 1987

By Murray D. Fredlund

The consolidation of soil material is central to many types of engineering analysis. Problems such as the building of highway structures, landfills, or buildings over saturated soft clays require application of such theory. It has been found in industry that the application of consolidation theory has lagged significantly behind the theory which has been developed some time ago. The application of small-strain saturated consolidation theory was first proposed in a 1D form by Terzaghi. Although this theory has been available for some time it?s implementation into software packages in 2D and 3D forms has been slow due to inherent complexities in the coupling equations. The flow and stress equations are also inherently somewhat unstable and this further complicates software implementation. Of particular interest in the mining industry is the consolidation of uranium tailings. One such disposal method that has been utilized is the subaqueous deposition of uranium tailings in large pit structures. When performing such deposition the calculation of consolidation rates is central to determining final pit capacity and expected life. Consolidation software can be successfully used in such cases in order to determine pit filling rates. The primary complexity, however, is that tailings are typically deposited in slurry form and therefore the potential deformations are large. Large-strain consolidation theory is therefore required in order to properly solve the deformations over time. This paper presents the use of a large-strain consolidation analysis in order to predict long-term filling rates in a uranium tailings pit.

Aug 1, 2010

By A. J. Benham, H. Kessler

In the UK a high proportion of land-won sand and gravel is extracted from sub-alluvial gravels and river terrace gravels located within river valleys. However, extraction from deposits of this type is increasingly proving to be less acceptable. Quarries within river valleys often have a high visual impact and the cumulative impact of these operations in close proximity to each other can be high (figure 1). River valley operations are almost always restored to open water. Whilst these may be attractive for nature conservation and provide leisure activities, they can also have a serious impact on the natural hydrology of the flood plain. Wet restoration of quarries located close to airports or airfields can also lead to concerns regarding increased risk of bird strike on aircraft. The Civil Aviation Authority recently suggested that an exclusion zone of 13 km be applied around all airports and airfields to reduce the potential for bird strikes on aircraft. This action is likely to have a serious impact on the availability of potential sand and gravel extraction sites in river valleys.

Jan 1, 2005

By D Mather, H R. Asche

"In the civil tunnelling field, the use of tunnel boring machines (TBM) has now overtaken the use of conventional excavation methods (drill and blast / roadheader). This is due to a number of reasons, including the increasing availability and reliability of TBMs, the ability to deal with a wider range of face conditions, and the reduced excavation cost that TBMs can bring.Mining companies have spearheaded the advances in shaft boring by mechanised means, both in blind and raise boring. However, mining companies have been slower to adopt mechanised tunnelling.When contrasted with a conventional mining contract, there are good reasons why TBMs in mining applications are relatively rare. A conventional decline contract may have very little geotechnical information. The decline alignment can be subject to change as the tunnelling progresses. The infrastructure requirements are less for a conventional decline, and the sunk cost prior to excavation commencing is lower. Contract documents can be very simple.The history of TBM use in mining is reviewed and lessons are described. From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.We believe that despite the additional requirements for TBM declines, the cost and time advantage to mining companies is very attractive. The challenge is to recognise and to meet the requirements for success in a TBM drive to achieve the advantages of: faster advance rates reduced rock damage/overbreak reduced support requirements uniform muck characteristics greater personnel safety.From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.CITATION:Asche, H R and Mather, D, 2014. Use of ?tunnel boring machines in the mine environment, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 655–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By Nikolay M. Sirakov, Michael L. Feves, Rumen P. Mironov, Daniel R. Hack

Subsurface investigation of sand and gravel deposits has generally been limited to test pits and borings. These techniques are problematic in terms of the accuracy, usability, and cost of the final data. Innovations in the application of geophysics have been gaining acceptance in the aggregate industry, especially to determine depth to bedrock and the extent of uneconomic inclusions. This paper presents a system to optimize the processing and evaluation of electrical resistivity data. The system uses 3D separation, geometrical reconstruction, and visualization of subsurface objects.

Jan 1, 2002