Search Documents

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By R Witt, M Lowing

Tanking of tunnels is now often specified when inflows exceed as little as 1 L/s/km with a unit distance of 100 m. To demonstrate inflows over a 100 m segment of a tunnel are less than 0.1 L/s with a standard error of 0.01 L/s by timed, gravity filled, volume measurement up and downstream of the segment, the measuring cylinder volume (L) must exceed 10 Q, where Q is the flow in L/s, and the number measurements taken and averaged must exceed 20 . If a standard error of 0.02 L/s is acceptable then 5Q2 measurements must be taken and averaged. If gravity filling is not possible then the number, n, of repeat pumped container measurement required is given by: where: is the 100 m section leakage is the volume filling time is the standard error of volume measurementZ is the standard normal variateK is a coefficient dependent on physical measurement conditions Based on analysis of field data an indicative coefficient of variation of volume measurement is ~0.05.

Jan 1, 2008

By Shawna Munn, Jakub Hudler

This paper outlines the use of tunneling headwall softeyes for transit construction projects in the Greater Toronto Area (GTA) over the past decade. Due to spatial constraints, tunnel boring machines were used to construct the underground tunnels requiring the design of launch and exit shafts with headwall softeyes to facilitate tunneling operations. Variable ground conditions and shaft geometries lead to the development of innovative headwall and tunnel softeye design applications using fiber reinforced polymer (FRP) elements (beams, reinforcing bars, and tiebacks). This paper outlines the challenges and benefits associated with designing and constructing shafts using various systems. Lessons learned throughout design and construction of more than 20 structures over the past 10 years are outlined. The constructability challenges with using FRP and design performance are also discussed. For over a decade, the City of Toronto has been expanding its metropolitan transit network with a variety of new transit construction projects. Two recent projects in the Greater Toronto Area (GTA) for underground infrastructure include the Toronto York Spadina Subway Extension and the Eglinton Crosstown Light Rail Transit project. These add a total of 31 new stations and 18.6 km (11.5 miles) of underground transit (TTC 2017) (EllisDon 2016). Due to ground conditions and spatial constraints of existing surface infrastructure, these projects utilized tunnel boring machines (TBMs) to construct the underground tunnels requiring the design of various types of shafts and headwalls to facilitate underground tunneling operations. To allow for tunneling through the headwalls, these shafts were designed with “softeyes” - a section of the wall without metal reinforcement that allows the TBMs to tunnel through.

Jan 1, 2018

By Camilo Quintero, Frank Cesario, John Kinnear, Brian Boye

In this paper, an innovative approach was adopted to automatically calculate the effects of tunnel induced settlement on buildings and utilities. The approach resulted in increased output quality, consistency, reduced time, cost savings and a greater ability to respond quickly to design changes. The techniques described have been applied to the Fairbank Silverthorn Storm Trunk Sewer System project, located within the City of Toronto. The automation allowed a very large area of topography, tunnels (6 km), buildings (9000) and utilities (over 1000) to be rapidly evaluated. Visualization of the settlements and impacts also allowed the project design team to optimize the system design to mitigate the settlement impacts.

Jun 13, 2021

By Jurij Karlovšek, Marko Žibert, Scott Keniston

"SUMMARY The importance of information management was recognised in surface construction industry decades ago, and has increasingly being recognised through formal process and laws. Around the world, these laws and codes of practice are currently being drafted and enacted, to reflect the development of software tools and corresponding increasing adoption by industry. This paper deals with specifics of implementing information modelling in tunnelling business utilising BIM (Building Information Modelling) technology developed for buildings as well as similar technology developed for mining industry. Although BIM is recognized initially as a 3D digital representation of physical and functional characteristics of a facility, the real benefits come when complex capability through construction sequencing and even detailed programming (4D) and cost capabilities (5D) are included. INFORMATION MODELLING The Architecture, Engineering and Construction (AEC) industry requires the production of design and construction information, which involves the input from several teams. The tasks allocated to each team need to be carried out in a particular order and coordinated in order to benefit all those involved and the project itself; this is known as “collaborative working”. To ensure the quality, and guarantee that information can be used without change or interpretation, working processes and standards needs to be agreed upon or else it will hinder collaboration and have a negative impact on project delivery. Case studies show that the additional capital delivery costs due to uncoordinated, inaccurate and ambiguous information amounts to 20-25%. The solution to overcome these problems and improve collaborative working in a project is the adoption of BIM. It is a modern approach to the design, documentation, delivery, and life cycle management through the use of project information databases coupled with object-based parametric modelling. BIM requires traditional practices shifting from simple drafting to using 3D native models for building design environment. Additionally, it requires that models are equipped with information that has been traditionally decoupled in a text or other kinds of documents. The goal is not in creating a 3D graphic representation of design intent; rather, it is a comprehensive information management tool based on the simulation of design and construction build around a central repository."

Jan 1, 2016

By Ernest Selig, John Dunnicliff, Delon Hampton

This paper provides a summary of a two-day conference held in New Orleans in March 1980, entitled "Tunnel Instrumentation: Benefits and Implementation." The conference addressed two major questions: First, what are the benefits of using instrumentation during tunnel construction? Second, what contractual relations should be established for conducting instrumentation programs during tunnel construction? Each session consisted of brief formal presentations and extensive panel discussions with participation from attendees. Attendees included owners, designers, contractors, and instrumentation specialists. This paper presents a consensus of views expressed during the conference.

Jan 1, 1981

By John Kinneen, Sunghoon Choi, Arne Fareth, Edward S. Barboe, Kyle R. Ott

A new water treatment plant is to be constructed for a portion of the water supply system of New York City. The project includes construction of new water conveyance tunnels crossing perpendicular and sub-parallel to the existing pressurized water tunnel at two locations. A study was conducted to evaluate the impact of new tunnel construction on stability of the existing tunnel and hydrojacking potential in the surrounding rock mass. This paper introduces a practical approach to evaluate tunnel interaction, expressed in terms of rock-liner interaction, stress-induced stability and hydrojacking failures. A simple method to evaluate hydraulic and mechanical properties of concrete liners and jointed rock mass is also presented.

Jan 1, 2007

By Peck W

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By Björn Johansson

"SUMMARY Every tunnel designer has to consider the power of water ingress when designing a new tunnel. Either you choose solutions with simple methods to divert the ingress water or a robust system with the intention that it will give gain on low maintenance costs and a long lifetime. This article describes a new method to divert ingress water in a robust way and more economical than traditional concrete lined tunnels. This system is based on a bolt grid suspending a water tight membrane, which is reinforced and covered with sprayed concrete. The method has been in limited use in Sweden since 2005 and with continuous improvement, still going on, it is now applied for the large project “Stockholm Bypass”, a 21km long highway project. TUNNEL MAINTENANCE RELATED TO WATER INGRESS The Swedish Transport Administration maintain approximately 190 various tunnels that is constructed by a number of different methods, (Swedish Transport Adm 2015). Commonly the ground conditions are good and fairly low ground support is needed. Contrary water and winter conditions can be sever, which gives high impact onto the tunnel design and in particular methods to protect against “frost and water ingress”. During a tunnels lifetime it is common that maintenance related to water ingress occurs several times and sometimes frequent occasions every year. Such maintenance costs and consequences of lost open time for the tunnel can rapidly become higher than the initial cost of the tunnel. Thereby it is obvious that spending time during design to evaluate requirements for a suitable system against water ingress is preferred. Icicles Icicles are formed when water is below freezing degrees and drips or run from an ingress point. At very cold conditions also water flows running at high velocity freeze into ice and a rapid growth can appear. If the integrity of the tunnel traffic area is interfered by icicles they urgently have to be removed before they cause an accident. Typically the tunnel or a part of the tunnel must be closed to do such maintenance. TUNNELS FROST AND WATER INGRESS PROTECTION IN SWEDEN In Sweden methods to perform “frost and water ingress protection” are primary developed for drill and blast tunnels as it is most common tunneling method. The foundation Swedish Rock Engineering Research has done a comprehensive report SveBeFo Rapport 77 that describes water and frost prevention in Swedish tunnels up to year 2005. Below is only slight description of those various methods. Lately some more attention is paid to concrete lined tunnels made by TBM since TBMs successfully built water tight tunnels in City Tunnel (Malmö) and Hallandsås Project. When environmental demands require maintained ground water levels, water tight tunnels made by pressurized concrete lining becomes more economical and on the same time also becomes protected from icicles and water drips."

Jan 1, 2016

By P. F. R. Altounyan, I. W. Farmer

Groundwater freezing was used to stabilise 8m thick beds of saturated and weakly cemented sands at a depth of 170m, during driving of twin 1 in 4,5.2m o.d. circular drifts from the surface to the Coal Measures through 600m of Permo-Triassic strata. Instrumentation was installed during erection of the lining in frozen and unfrozen ground to measure ground and groundwater pressures on the lining and ground temperatures up to lm into the frozen ground. Observations showed that following thawing, effective lining stresses in the frozen zone were low, indicating minimum strata disturbance during freezing and subsequent machine excavation. Groundwater pressures were lower than expected.

Jan 1, 1981

By Jeff Hammer, John McGregor

"The Twin Tunnels, originally constructed in 1964, have become a major choking point for trafficheading up to and returning from the Colorado high country along the I-70 corridor. To increase traffic flow, the Colorado Department of Transportation undertook the first widening of the East Bound Tunnel in 2013. After the successful completion of that project, CDOT began the widening of the West Bound Tunnel in 2014. Both projects had a limited schedule for tunnel construction of just nine months. The innovative blasting and demolition of the existing tunnel lining was a crucial component to the success of both projects. During the construction of the West Bound project in 2014 a large amount of surface bench blasting using conventional methods ran concurrently to the West Bound tunnel excavation to allow for enough room for the new tunnel portals."

Jan 1, 2016

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By S. Klein, M. McLeod, K. Johnson

The East Bay Municipal Utility District (EBMUD) delivers water to the San Francisco Bay Area through an aqueduct system extending from the Sierra Nevada Mountains to the East Bay. This aqueduct system, the Mokelumne Aqueducts, are comprised of three 82-mile long steel pipelines. The portion of the aqueducts crossing the Sacramento-San Joaquin River Delta is recognized to be vulnerable to seismic and flooding hazards. Previous studies evaluated alternatives for mitigating these hazards and increasing the reliability of the aqueducts for the next 100 years. The preferred solution involves construction of a 16.5-mile tunnel across the Delta and re-routing the existing aqueducts through this tunnel

Dec 1, 2022

By T Isaksson, J Anderson

The procurement process for underground construction contracts, in particular those contacts involving tunnel boring machines (TBMs), is subject to many complex and inter-related variables, including national and local politics, public policy, community involvement and media attention û as well as strict environmental and legal requirements. Other restrictions include the time available to adequately investigate geotechnical conditions and viable technical options to determine the best construction methodologies û including selection of tunnel boring machine characteristics and, those construction means and methods suitable for the specific geotechnical and environmental conditions. The latter are, most often, quite imperfectly understood. æGetting it rightÆ implies that an optimal configuration û of machine type, characteristics and associated methodologies û can be found and successfully implemented for a particular project. æFrom the beginningÆ implies that the lack of time issue can be successfully resolved. Within an international context this paper highlights a number of issues of concern which relate to tunnel procurement systems and the ways in which certain key processes are managed during planning, design and construction. The authors argue that there is considerable room for improvement in the way tunnelling projects are undertaken and an approach is discussed which has the potential for substantial gains in cost and schedule and reduction of risk. Savings, however, may only be fully realised if the new methods can be fully implemented by all parties involved. This, we believe, will require the rejection of ætraditionalÆ forms of management and procurement with associated changes in the roles and responsibilities of owner, engineer and contractor. Additionally, risk identification, assessment and mitigation are essential cost and schedule control process which have, to this point, been underutilised by the underground construction industry.

Jan 1, 1999

By Ronald E. Triplett, George K. Burke, Bernard H. Voor

To accommodate larger double-stack rail cars through a tunnel, the existing active tracks were to be lowered. The tunnel is an elliptical, horseshoe-shape with concrete base support, removal of which would jeopardize the tunnel integrity, particularly since the soils beneath part of the tunnel floor included soft, saturated silt overlying rock. Grouted bar anchors combined with a SuperJet soilcrete strut replaced the existing support in situ prior to floor lowering. Close cooperation and detailed timely engineering support provided a quality project. Project design and construction, ground improvement methods, and the performance of the work are described.

Jan 1, 2001

By Trenton Cohen, Joseph McDivitt, Shimi Tzobery, Joseph Sinacori, Scott Zylstra

The 2-mile Beach Interceptor Sewer Tunnel was constructed in 1954 to then-current mining and construction standards. Due to its lifespan and deteriorating condition it is now being stabilized and rehabilitated using conventional excavation and ground support. At its southern end, below the prestigious Three Arch Bay community, the original tunnel alignment passes under a historic landslide where the tunnel was sand-backfilled and capped by bulkheads in 1957 due to severe and caving ground conditions. Video footage of the existing 21- inch clay pipe showed that the pipe is severely damaged, which could potentially cause a catastrophic pipeline failure and sewage spill into the Pacific Ocean. This paper summarizes the thorough investigation and design process, tunnel realignment construction and monitoring, and the notable cooperation between all parties to overcome the project risks.

Dec 1, 2022

By Thomas J. Crocker, Galen G. Waddell, Eugene H. Skinner

This paper describes a method of measuring initial and long-term deformations which occur in the medium surrounding mine accessways, and discusses the importance of this type of measurement in assessing support-problem areas. Delineated are (1) description of the rock-deformation monitoring equipment, (2) results of two field tests which monitored rock deformation around 4-foot-diameter raise bores, and (3) a numerical-analysis (finite-element) technique to correlate theoretical with experimental results. Instrumentation developed provided the sensitivity and resolution needed to measure rock deformation around a full-scale raise bore during excavation. Results of the tests conducted at the Lucky Friday mine, Mullan, Idaho, show the relationships between (a) de- formation vs. time, and (b) deformation vs. bit progress. Based on theoretical evaluation of the initial deformation, the medium appeared to behave elastically. Using an estimated field stress of 5,500 psi and Poisson's ratio of 0.20, the gross modulus of elasticity of the rock was calculated to range from 3.15 to 6.0 x 106 psi (with one outlier which was determined to be >12 x l06 psi).

Jan 1, 1971

By Herbert E. Lindberg

Laboratory-scale intact and jointed rock masses were tested in field and laboratory experiments to investigate tunnel response in high stress environments. In most of the experiments the tunnels were modeled by a rigid-plastic foam polyurethane with a crush strength of 3.4 MPa (500 psi) and emphasis was placed on jointed rock parameters: joint sets (single set of parallel plane joints versus a double set of orthogonal parallel plane joints), joint plane angle with respect to the direct loading direction, and joint spacing. Other parameters were loading stress, loading direction, and tunnel reinforcement strength. Results show quantitatively the increase in tunnel deformation in jointed compared with intact rocks, double versus single joint sets, and large versus small angle between the joint plane normal and the loading direction. A surprising result was the decreases in tunnel deformation with increases in the number of joints across a tunnel diameter. The efficacy of scale modeling with laboratory-constructed rock was tested by modeling complex reinforced concrete and steel tunnel reinforcements in jointed rock masses and comparing the results with large scale tunnels previously fielded in highly jointed granite. Tunnel response was reproduced in surprising detail, including concrete fracture, steel liner bending and fracture, and critical load to produce these responses. The scale models also allowed sectioning of the jointed rock masses to observe gross sliding along the joints that accompanied tunnel failure.

Jan 1, 1982