Search Documents

By I. M. Eitani, M. Karmis

Ground control presents the most serious problem in underground thick seam mining. In addition to parameters such as depth thickness and inclination of the seam and nature of the coal and the immediate strata, the stress interactions caused by the mining sequence must be carefully evaluated and understood, if safety and productivity objectives are to be fulfilled. In this paper, the most widely-accepted thick seam coal mining methods are reviewed and suggestions are made for future work pertaining to ground control problems.

Jan 1, 1981

This paper describes thick seam mining as practised at Westfalen Colliery, Redbank via Ipswich,in South Queensland. The author describes the develop- ment of the mine from conception to the time of successful operation and compares the two systems of mining adopted at the colliery.

Jan 1, 1976

The author describes 1. The classification and characteristics of various thick seam mining techniques in various Japanese coal mines. 2. Practices of thick seam mining methods experienced in Taiheiyo Coal Mine. Currently, thick single lift, simultaneous multi lift and non simul- taneous multi lift mining methods are adopted as underground flat thick seam excavations in Japan. These are now reliable and effective in increasing the extraction ratio. At Kushiro Colliery of Taiheiyo Coal Mining Co., these three thick seam mining methods have been used. According to the results, if solidification of the top lift goaf is essential, the non simul- taneous multi lift mining method is the most effective in increasing the extraction ratio without minimising productivity of each lift and it points out that further development of this method is necessary.

Jan 1, 1976

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24v0 of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50v0 of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include: • extraction of thick seam in ascending order with stowing; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. • Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof; four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 1, 1988

An approach to underground mining of shallow dipping, thick seam coal is proposed in broad outline. The method is based upon overhand slice and fill, with hydraulically emplaced washery refuse as the filling material. Likely fill behaviour and character- istics are discussed and likely problem/investigational/ research areas defined.

Jan 1, 1976

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By Yan Beygelzimer, Alexander Spuskanyuk, Victor Varyukhin

"The main idea of the report is that the yield surface can be presented as thick, ""foamed surface"" with dimensionality exceeding two. By other words, perhaps, the yield surface is fractal, i.e. it belongs to the class of geometric objects with fractional dimensionality. Apparently, fractal structure of the yield surface is determined by the fractal structure of natural materials. ""Cloud of internal stresses"" term is introduced to describe the stress distribution in representative volume element. Its plastic flow is determined by the interaction of this cloud with the thick yield surface. Thick yield surface and internal stress cloud concepts allow to determine an additional correlation between micro mechanical models of polycrystals and phenomenological theory of plasticity.1. IntroductionClassical plastic flow models are not satisfying the modem requirements. There are two main directions in their development. The first, mathematical, is connected with the development of the general theory of rheological relationships; the second, physical, is connected with the development of the representative volume element (RVE) models which are based on specific ideas about deformation mechanisms. Within the framework of the first direction, the macroscopic experimental data is formalized; the second approach deals with the generalization of physical research results for the different scale levels that are involved in plastic deformation.These approaches have advantages and disadvantages. In phenomenological theories, the advantages are the mathematical simplicity and laconic formulation of constitutive relations, which allows using them in practical calculations. However, the mathematical models of this class can not be considered as general, they are useful only for the description of limited range of deforming processes. On the other hand, physical theories that are based on the description of real plastic deformation mechanisms are very explanatory and predictive, but they lack mathematical simplicity. The above circumstances lead us to the necessity of compromise that can be found in determining the constitutive relations for RVE, which structure and parameters would bear the information about rnicrolevel and mesolevel phenomena. In this synthesis direction, the fundamental role belongs to [1,2], etc."

Jan 1, 2001

By James M. Johnson, David Landriault, Frank Palkovits

The term “Paste Technology” was first used in the late 1980’s. It was used to describe a high fines (15 wt% or greater minus 20 microns), low water content backfill material that could be transported underground through a borehole/pipeline distribution system (4” to 8” dia.) at a yield stress similar to fresh concrete (100 to 400 centipoise). This “Paste Backfill”, unlike slurry transported backfills does not segregate into separate solid and liquid phases at low pipeline transport velocities or upon disposal into the underground stope. Paste backfills can consist solely of fine material, or can include fines plus sand and aggregate similar to a concrete mix. Pipeline transport of paste requires that sufficient fine material (minus 20 micron content) is contained within the mix to lubricate the pipeline walls to create a plug flow condition. For concrete, the fine material is supplied through the cement addition to achieve high compressive strength. For paste, the fine material is generally available in large quantities in the form of mill tailings. The paste tailings can be transported underground for use as backfill or discharged on the surface in a tailings management facility (TMF). This natural abundance of fine grained material is not exclusive to mine tailings but is common to many waste streams in many different industries. This makes the disposal of many waste materials very amenable to paste pipeline transport and placement as a non-segregating slurry. The potential use of paste technology for a wider group of waste materials was realized by these authors and others over two decades ago. Through the effort of this small group the use of paste technology has expanded over the years to become recognized as a low cost, environmentally superior, and technologically controllable method of transporting and placing specific material waste streams with a low water content and high placement density. The high yield stress nature of a paste also lends itself well to the blending of one or more coarse waste materials into the fine waste material paste stream. This allows all the waste materials to be transported by pipeline, increases their placement density; decreases the supernatant release/treatment, reduces contaminant mobilization, hydraulic conductivity and oxygen/water reactivity through encapsulation in the paste matrix. The following paper describes the present state-of-the-art use of paste technology in the world today. It also describes future uses of the technology that are under development and speculates on the overall use of the technology for waste management in the future.

Jan 1, 2005

By V. L. Mitsopoulos

This paper provides a summary of tailings disposal techniques and the improvements that have been made through the introduction of thickened tailings disposal. The general properties and characteristics of thickened tailings are described, as is a design process for selecting appropriate technologies for thickening, pumping, transporting and storing tailings. The factors affecting the selection of an appropriate disposal site and operational considerations for the effective utilisation of tailings storage areas are also documented.

Jan 1, 2006

By Jonathan Matthews

Efficient and effective management of mine tailings is essential for continued successful development of Alberta?s vast oil sands resources. Syncrude Canada Ltd. continues to research novel tailings management techniques in an effort to improve production efficiency and environmental sustainability. During the summer months of 2001, Syncrude Canada Ltd., in collaboration with members of the Canadian Oil Sands Network for Research and Development (CONRAD), conducted field-scale trials of thickened tailings technology at Syncrude?s Aurora mine, north of Fort McMurray, Alberta. This paper provides an overview of the test program including discussion of objectives, test configuration, and program observations. 0Data collected during the field trial indicate that substantial swings in feed slurry composition challenge effective thickener operation. When coarse mineral solids dominated slurry composition, thickener rake torque rose to unmanageable levels. It was determined that the end-of-pipe depositional characteristics of thickened oil sands slurry were generally consistent with present understanding of oil sands tailings slurries. After shear, thickener underflow product exhibited very shallow beach angles and a limited capacity to keep coarser particles in suspension indicating that stacking of ?paste-like? thickener underflow product from a conventional thickener is not practical in an oil sands setting unless process adjustments can be made to increase the underflow density and/or preserve the initial high yield stress of the underflow during transport and deposition. These technical challenges notwithstanding, Thickened Tailings technology offers considerable promise for recovery of warm water from oil sands process tailings.

May 1, 2003

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022

By Leena Vesa, Antti Remes

Design of thickeners is based on laboratory test work, characterizing the material and determining the optimal reagents, dosages and settling regimes. Several methods for dimensioning plant scale equipment exist. Kynch and Talmage-Fitch design procedures has been applied widely for a long time. Nowadays, besides them, a dynamic laboratory test work is applied for design of high rate thickeners. In that the laboratory unit is operated with known solids load per area, feed and flocculation conditions and with raking of the underflow. All these test methods afford useful data for setting up and calibrating a dynamic simulation model of a plant scale thickener. This paper presents a flocculation kinetics based dynamic thickener simulation model and a procedure to calibrate the model parameters. With the model, the underflow stream composition can be simulated over time as a function of the thickener operating parameters, which are: the feed rate and composition, underflow pumping rate, flocculant dosage and dilution of the feed. In addition, the model incorporates calculation of the slurry bed level, the cone pressure, the yield stress and the rake torque. Such a dynamic modeling scheme enables setting up simulation aided operator trainings and developing and testing of advanced control strategies, for example. The unit model can be integrated as a part of concentrator-wide flow sheet simulation model as well. Here, calibration of the kinetic flocculation model based on a laboratory test case data and further the operation of a simulated plant scale thickener are presented.

Jan 1, 2014

Thickener Modelling - Incorporating Shear Effects

Sep 13, 2010

By R. J. Smith

Hornestake's Mclaughlin Mine is the first commercial application of pressure oxidation pretreatment of gold prior to cyanidation. Inherent to the autoclave process are several liquid/solid separations. Flocculant consumption represents a significant portion of the consumable reagent costs at McLaughlan. This paper focuses on the efforts of the Operating, Metallurgy and Engineering groups to improve thickener operation and minimize flocculant consumption. An operating philosophy incorporating feed solids control, increasing flocculant dilution water and minimizing flocculant solution shear has resulted in a reduction in 1986 flocculant costs of $0.054/t ($0.06 st) versus 1985 costs. Additional changes are projected to result in a further cost reduction of $0.20/t ($0.22/.st) in 1987.

Jan 1, 1988

By Donald L. King

This paper has been prepared with the objective of providing basic information on thickening equipment as applied to mineral processing plant design. Thus, by design, the content is elementary, yet sufficiently informative to advise the reader concerning the thickening and clarifying process, equipment configurations, installation and operation. Practical considerations are provided for slurry samples for testing, evaluation of testing, preliminary sizing, duty classification, and thickener selection to enhance operation, see icing and control. Illustrations are provided to both inform and demonstrate present state of the art features and capability.

Jan 1, 1978

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thickners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter.

Jan 1, 1949

By Thomas W. Healy, David V. Boger, Yee-Kwong Leong, Lee R. White, Peter J. Scales

The concentration of mineral slurries by conventional thickening devices is discussed. The role of additives on the compression of mineral slurries is also examined. Results for a range of flocculation conditions are presented. The compression of flocculated mineral slurries is found to be highly dependent on the fundamental particle-particle interaction forces and hence, the rheology of the particulate fluid. It is demonstrated that a detailed knowledge of the properties of both the mode of operation of the thickening device and of the solid/liquid interface is required for improvement in the rate and in particular, the extent of dewatering.

Jan 1, 1995

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014

By H. Hamza

Oil sand tailings are disposed of in large ponds in which MFT (Mature Fine Tailings, a stable suspension of fine particles in water) forms after many years of settling. Long-term storage of large volumes of MFT is costly to maintain and also poses an environmental liability. The Advanced Separation Technologies laboratory at CANMET Western Research Centre has worked closely with oil sand companies to eliminate MFT generation by applying paste technology to oil sand tailings. In this process the fine tailings are flocculated to produce a thickened material that has the potential to consolidate to a dry landscape, while warm water is recovered and recycled for reuse in the extraction process. This paper presents some results of an extensive technical program involving bench-scale tests for flocculant selection and continuous thickener pilot tests.

Jan 1, 2002

By W. Julian Patron

TREATMENT of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro- separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low- grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. OPERATION AND TYPES OF SETTLING EQUIPMENT Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1946