Search Documents

By Alicia Esther Ares

This study was conducted to investigate the directional solidification of Zn-20%A1 and Zn20% A1-1O%Si-3o/oCu alloys under different conditions of heat transfer at the metal/mould interface. The type of structure obtained in both cases was analyzed and related to the solidification thermal parameters such as cooling rate, growth rate, thermal gradient and recalescence which were determined from the temperature versus time curves. These parameters were correlated with the structure-like length of columnar grains and size of equiaxed grains. The metallographic analyses were done performing quantitative metallography and composition analysis of the different alloying elements along the cast samples by SEM (Scanning Electron Microscopy) and EDXA (Energy Dispersive X-Ray Analysis). Correlations between properties, structures and thermal parameters were found.

Jan 1, 2008

By S. K. Samal, B. Mishra, M. K. Mohanty, S. C. Mishra

Steelmaking industries consume the majority of chromium and manganese ferroalloys to impart several properties in steel and also for other purposes. The quality of ore governs the process kinetics as well as the process economy of the ferroalloy industry. The present study demonstrates the thermal transformation behavior of chromite and manganese ores with varying compositions. Simultaneous thermal analysis (DTA/TG) is employed for such ore samples where the transformation of mineral phases is correlated with the thermogram characteristics and quantified. Phase, microstructure, and compositional analysis results of individual ores corroborated with thermal analysis are in good agreement. Chromite samples are ferruginous with goethite and gibbsite contents, whereas manganese ores vary in composition and also exhibit multiple and/or overlapping transformations.

Jan 21, 2021

By SUMANT KUMAR SAMAL, BHAGIRATHA MISHRA, MANOJA KUMAR MOHANTY, SUBASH CHANDRA MISHRA

Steelmaking consumes the majority of chromium and manganese ferroalloys for purposes such as to impart various properties to steel. The quality of ore governs the process kinetics as well as the process economy of the ferroalloy industry. The present study demonstrates the thermal transformation behavior of chromite and manganese ores with varying compositions. Simultaneous thermal analysis (differential thermal analysis/thermogravimetry, DTA/TG) was conducted on these ore samples, where the transformation of mineral phases was correlated with the thermogram characteristics and quantified. Phase, microstructure and compositional analysis results of individual ores corroborated with thermal analysis are in good agreement. Chromite samples are ferruginous with goethite and gibbsite contents, whereas manganese ores vary in composition and also exhibit multiple and/or overlapping transformations.

By E. Nurminen

Thermal transport properties of copper flash smelting flue dust have been investigated. Such values of the dust are needed to correctly model the process and to optimize its heat recovery performance. Dust accretions on heat recovery boiler walls may have a significant influence on the boilers heat transfer efficiency. Measurements of the thermal transport properties have been made for industrial flue dust and for pure sulphate components. The measurements have been conducted at temperatures up to 400 °C and the effect of porosity on these properties has also been investigated. The results indicate that the flue dust and the sulphate components are effective thermal insulators and the dust build-up on the boiler walls is likely to greatly decrease the heat transfer efficiency of the boiler.

Jan 1, 2007

By S M. J Koleini, F Hedjazi

The purpose of this research was to study the calcination of lead-zinc flotation tailings from the Angouran lead and zinc flotation plant in Iran as a pre-concentration step prior to hydrometallurgical processing of the oxidised tailings. There is an abundance of these tailings in the Angouran region and making use of these tailings would help preserve national wealth and also reduce the serious problems of environmental pollution caused by the tailings. At the optimal conditions of calcining at 750 - 800¦C for 45 minutes, the sample showed a mass loss of about 19 per cent. Mineralogical analyses showed that under these conditions the carbonate minerals including smithsonite (ZnCO3), calcite (CaCO3) and dolomite (Ca Mg (CO3)2) decomposed to their respective oxides. Hemimorphite (Zn4Si2O7 (OH)2.H2O) converted into willemite (Zn2SiO4) and this transformation postponed the formation of silica gel in the leach solution. The grade of zinc increased from 22.20 per cent to 29 per cent. These mineralogical changes resulted in desirable reactions in the acid leach process.

Jan 1, 2004

By I. Gaballah

Jarosite contains up to 15 % of heavy metal compounds 'HMC'. The current waste disposal methods will not be allowed in the near future due to new environmental regulations and pollution risks. For these reasons, thermal treatments of raw or decomposed jarosite, in controlled atmospheres, were investigated. The aim of these treatments is to decontaminate the jarosite and/ or to recover the HMC for recycling. According to physico-chemical characteristics of the samples, the thermal treatments in controlled atmospheres N2, CO+N2 and C12+air lead to the extraction rate that vary from 93 to 98 %. Heavy metal compounds were separated by cooling the gaseous phase. The treatments' residue was almost free from HMC. Between 700 "C and 800 "C, the chlorinating treatment was successful of eliminating more than 97 % of HMC contained in four different samples.

Jan 1, 1999

By K. Chomyn, R. Veenstra, P. Zangeneh, Hatch Ltd., C. Van der Woude, H. Ghorbani

"The furnace is the heart of smelting operations, and therefore the performance, reliability, and campaign life of the furnace are critical considerations. Furnace refractory is exposed to high temperatures and other harsh operating conditions causing brick erosion, crushing, and cracking, typically limiting the furnace campaign life and requiring costly furnace shut-downs for refractory re-lining. Despite extensive study, the in-service thermal / mechanical stresses in these complex refractory systems are not generally well understood. Hatch has developed a thermal-mechanical finite element analysis (FEA) based furnace refractory modeling approach that allows for the quantification of refractory movements, load distribution, and thermal / mechanical stresses.Due to the complexity of the refractory system, a range of models are used to identify and assess damage mechanisms and design improvements, including: 2D models, to capture expansion and movement of individual bricks, changes to load paths, and thermal stresses; and 3D models, to include the effect of differential expansion between bricks in each course, and assess overall load distributions. The 2D and 3D analyses include the effect of nonlinear temperature-dependent properties, thermal expansion, movement of individual bricks with frictional contacts (i.e., gaps can open, bricks can slide), and brick tensile or compressive failure. Both as-built and damaged conditions can be investigated (e.g., after bath zone brick erosion), for circular and rectangular furnaces. 3D models also include papering and brick joint & interface action.Analyses using these models have shown the importance of thermal stresses, papering, and geometry / arrangement of individual bricks. Results have been used to identify and assess damage mechanisms, showing good alignment with furnace autopsy observations. By using this FEA-based approach to quantify the refractory design, the risk of damage can be significantly reduced, low-cost design changes can be identified, and the furnace campaign life can be extended.INTRODUCTIONThe furnace is the heart of smelting operations and therefore the performance, reliability, and campaign life of the furnace are critical to the success of the smelting operation. Furnaces are inherently exposed to high temperatures, often in excess of 1600°C (Holappa, 2004), and furnace operating power has progressively increased over time (Voermann, Gerritsen, Candy, Stober, & Matyas, 2004). The refractory system must withstand high temperature, high heat flux, and other harsh operating conditions. These conditions are particularly significant for the furnace hearth, and can lead to damage including brick erosion due to molten material flows, crushing due to thermal expansion loads, and cracking due to severe thermal gradients within the bricks. Refractory damage typically limits the furnace campaign life, requiring costly furnace shut-downs for refractory re-lining (repair or replacement). In some cases the refractory may lose integrity causing damage to nearby equipment and harm to personnel."

Jan 1, 2016

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4)-air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) measured thermal-runaway pressures of lithium iron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 4260 psia (294 bar) of pressure during a thermal runaway, far exceeding minimum pressure containment specifications for conventional explosion-proof enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce thermal-runaway pressures to levels below that expected for CH4-air ignitions. Measured thermal-runaway temperatures were below the minimum autoignition temperature of CH4-air.

By Frederick J. McGarry, Parviz F. Rad

Although tunneling machines have attained very high advance rates in medium-hard rocks, the need for frequent repairs has slowed their use in very hard rocks. Laser- assisted tunneling is expected to improve tunneling machine performance by improving either specific energy or amount and quality of muck. The beneficial effects of lasing are the initiation and growth of microcracks from differential thermal expansion of grains, and overall spalling in the vicinity of the lased area. Using a constant thrust rock cutting device with disk cutters, the effects of cutter geometry, cutter diameter, thrust, and speed variations on specific energy and muck were explored and the improvement in performance of disk cutters caused by lasing was evaluated. It was found that the improvement depends on beam power and density, beam speed, pattern of heating, and cutting pattern and procedure. A focused beam slightly offset from the cutter path gives the most improvement both when cutting on a smooth surface and when cutting in previously cut grooves.

Jan 1, 1971

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By Imre Gombköto, Barnabás Csoke

"Raw material management means not only mining and processing of primary raw materials like ores, but means also collecting and processing secondary sources of raw materials. Recycling is one of the most developing field of raw material management in Europe, and its solutions are derived from mineral processing roots and principals. Complexity and challenges of the field of recycling results innovative solutions of material processing- Since European Union identified 20 raw materials as critical (CRM) due to lack of primary sources within the border of the EU, recycling become more recognised as source of different raw materials. WEEE is the waste streams contains many of the critical elements and along them at least 15 different species of plastics of which recycling is delayed by a lack of effective separation technique. Most paper deals with separation methods based on different specific gravity, triboelectric charge or surface properties of plastic species. Plastics however have differences of thermal properties and thermoplastics, duroplasts and elastomers can be recognised. The experiments described in the paper aimed to determine thermo adhesive behaviour of plastic species often identified in WEEE streams for separation purposes. According to the results, some plastic types as PS, PP. PC or PVC and PET pairs are possible to easily separate from each other, however different additives are changing thermo adhesive properties of most of the plastics that makes industrial process difficult to develop. Along thermo adhesive behaviour, combination of physical interaction can be used to enhance separation selectivity.INTRODUCTIONPlastics has a relatively long term of history as a light, multi-functional material in construction, packaging, automotive industry and electric and electronic products. There are a numerous types of plastic species can be used for various applications therefore they amount are growing from year to year. This quantity however become part of the waste stream and while metal recycling has been done for decades due to its economic value - cheap plastic parts are less desirable as secondary products. In 2013 an annual 5% of plastic production growth has been estimated with a base data of 265 million tonnes at 2010 (Guiqing & Zhenming, 2013). Since landfill requirements are increasing while—especially in Europe where actual regulations are trying to deflect waste from landfills - landfill capacities are decreasing, costs are become more and more expensive, Applications like energy production based on plastics as a fuel or recycling are some of the options can be applied. Direct incineration of plastics are applied at many plants - in most cases where waste consist of dangerous substances are incinerated because plastics high calorific value helps correct average mixture composition enable operators reaching high enough temperature for combined power and heat generation while most of substances—like PAH, PCB or dioxins—are destroyed. Another path is using low temperature reductive cracking due to pyrolysis process, however the chance having higher concentrate of carcinogen substances in the products are higher since it applies around 400°C during the process."

Jan 1, 2016

By I. D. Ustinov, V. A. Arsentyev, A. O. Mezenin, A. M. Gerasimov

"The solid mineral raw materials of the sediment deposits containing the argillaceous variations such as the coal and the potash ores are the most multi-tonnage solid minerals mined and processed in the territory of the Russian Federation. Both types of the deposits have relatively simple geology aspects with large and medium-sized solids and as a rule, the most often, with the regular bedding which are characterized by the fitchery thickness and the internal structure. Such deposits are very difficult for mining and processing. The thermal modification of this of ores allows changing the physico-chemical properties of its components in such a way that their further processing - grinding, separation, transportation and storage can be carried out without the use of process water or significantly reduces its consumption. The purpose of the present study is to increase the efficiency of the mineral processing containing the layered aluminum silicate by reducing their negative impact on the basic dressing processes, the separation of suspended matters and the storage of waste. INTRODUCTION Many deposits of minerals are associated with the presence of layered silicates such as the argil, mudstones, argillaceous slate - highly hydrophilic mineral varieties which have the ability to swell in the water. This ability to self-disperse creates the great difficulties both for the extraction and the processing of such ores. Since the dressing of most minerals is associated with the use of wet processes, where in contact with water the swelling layered silicates are dispersed to a particle size of less than 50 µm, but due to their high hydrophylic property they form bonds that promote the formation of so-called structured suspensions having increased viscosity. In this case the structured suspensions make it difficult to perform the separation operations as the classification, the gravity and magnetic separation, the flotation and thickening and filtration operations."

Jan 1, 2018

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of individual particles, which differs for different species of mineral. When a mixture of fine material is exposed to a radiant energy source, the various solids components present in the mixture will absorb heat energy depending on their composition and there will be difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz of 6 x18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Mar 2, 2022

By D. PATIL, B. K. Parekh

Water is the mainstay for the beneficiation of fine-size coal and minerals, but it is also the least desirable constituent of the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of the individual particles. When a differentially heated solid mixture is placed on a moving belt that has been coated with low-temperature melting resin, the hotter component of the mixture will stick to the belt while the relatively cooler component will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz particles of 6 × 18 mesh size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary test results show that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

By Shadia Ikhmayies

Thermo-Calc software was used to investigate the phase diagram of the calcium silicon (Ca–Si) system for the range of Si mass percent 0–100, and temperature range T = 200–1800 K. The melting points of Ca and Si deduced from the phase diagram are very close to the values obtained experimentally. Three stable intermediate solid phases were found, which are Ca2Si, CaSi, and CaSi2, where the first one appeared in the Ca rich side of the phase diagram, and the third one in the Si rich side. In addition, three eutectic points were found at Si mass percents of 3.95, 33.00, 62, and temperatures T = 1048.7, 1519.14, 1308.5 K respectively. Atomic Si (Diamond structure) is found mixed with CaSi2 intermediate phase for temperatures less than 1305 K, and mixed with a liquid CaSi for higher temperatures. These results are important for thermodynamic and metallurgic studies of these intermediate phases.

Mar 1, 2018

By Shadia Ikhmayies

In this work Thermo-Calc software was used to calculate the phase diagram of the Fe–Si system. The deduced phase diagram includes twenty fields, where three fields represent pure phases; two solid solutions and a liquid phase. There are several fields of two co-existing phases; mixed solid phases, and mixed solid with liquid phases. A set of eutectic and eutectoid points were found, where transformation reactions and temperatures were identified. The results were compared with results in the literature and good agreements with some differences were found. This study is a step to understand the phase diagram of Ca–Fe-Si system for refining metallugical grade silicon (MG-Si).

Mar 1, 2018

By M. Fafard, M. Dupuis, P. Goulet, J. Bédard

Start-up of a Hall-Heroult cell is a delicate task that can affect pot performance and pot life. Modem practices for high amperage cells involve preheating the lining before the molten electrolyte is poured in. Different preheating methods and heat-up schedules are used throughout the industry, and the optimum between a short start-up and damage minimization to the cell is elusive. Direct electrical coke-bed preheating is one of the most common techniques. This practice typically results in a non-uniform surface temperature distribution and can generate detrimental thermal gradients in the cathode blocks. Numerical modeling is an invaluable tool to study this complex problem and can help improve the preheating procedures. The modeling of the mechanical response of the lining is critical to detect risks of cathode block cracking or the development of gaps where liquids could leak into. Taking into account the baking of ramming paste, the quasi-brittle nature of carbon and the contact interfaces between different materials are examples of key elements to consider. A finite element slice model of a cell was built and simulations of different electrical preheating scenarios were performed using the inhouse code FESh++ to demonstrate what can be learned through thermo-chemomechanical modeling. The potential industrial application of the model is discussed.

Jan 1, 2006

By Tracy Brettmann, Melis Sutman, C. Guney Olgen

"The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their behavior during temperature changes. This paper focuses on the thermo-mechanical response of three full-scale energy piles installed in Richmond, TX. The behavior of test piles subjected to thermo-mechanical loadings was studied in situ with the aim of quantifying the thermal influence on the performance and capacity of energy piles. An extensive field test program, including conventional pile loading tests and application of heating-cooling cycles was conducted on the test piles during a period of six weeks. For thermal load applications, the heat exchanger fluid with maximum temperature of 113°F (45°C) and minimum of 47°F (8°C) was circulated in the geothermal loops placed at the center of the test piles. Optical fiber sensors, vibrating wire strain gages, thermistors and thermal integrity profile wires were installed to monitor the strain and temperature variations along the energy piles throughout the field tests. The strain and temperature profiles during heating-cooling cycles on the test piles under static loads and without a maintained load were monitored to investigate the effect of thermo-mechanical and pure thermal loads on the energy piles, respectively. Conventional pile load tests were applied before and after the application of thermal cycles. The results of the pile load tests are compared to evaluate the effect of temperature cycles on pile capacity.IntroductionEnergy piles are deep foundation elements designed to access and exploit the relatively constant temperature of the ground and its heat storage capacity for efficient heating and cooling of buildings. The deep foundation elements that are already in place for structural support are integrated with adsorber pipes to perform as heat exchangers connected to ground source heat pump (GSHP) systems. With the use of energy piles, the heat energy is fed into and withdrawn from the ground for cooling in the summer and heating in the winter, respectively.Energy piles present an innovative way to harvest near-surface geothermal energy and to provide lower carbon emissions, however, there are still pending question on their performance. During heating-cooling cycles, energy piles experience temperature changes, which result in expansion or contraction of the piles."

Jan 1, 2017

By C. Y. Tang, Z. H. Chen, T. C. Lee

"In sheet metal forming process, the forming limit and strain distribution are governed by plastic instability and fracture following strain localization. It has been proved that the temperature gradient caused by plastic deformation as well as friction is one of the crucial factors to induce the strain localization in high-speed metal forming processes. In this paper, a numerical simulation of the sheet metal extrusion process has been conducted by using thermal-mechanical coupling finite element method. An improved mixed finite element method has been used to solve the large deformation elasto-plastic problem. In thermal phase, the transient heat transfer finite element method together with the Crank-Nicholson algorithm has been employed to determine the temperature field. Both the numerical results and the experimental observations reveal that the temperature gradient plays an important role in inducing the strain localization, which eventually leads to fracture failure in the sheet metal extrusion process.IntroductionSheet metal extrusion is such a process where the extrusion punch penetrates into one surface of the sheet metal material to let it extrude and flow towards the outlet of the die. This process can be used to produce protruding parts on a strip material. In engineering applications, the quality of the product is affected by many factors such as stress state, loading speed, material properties and lubrication condition. The research on failure mechanisms and improvement of formability in sheet metal forming processes by exploitation of differential thermal conditions has been of great interest recently [1-3]. It has been proved that the temperature gradient caused by plastic deformation, heat transfer, and friction between sheet and tools is one of crucial factors to affect 'the formability in high speed sheet metal forming processes [4]. In our previous study of sheet metal extrusion, it has been observed that plastic deformation is highly localized and some specimens are subjected to fracture failure in the form of crack propagation [5]. To understand this failure phenomenon, the effects of temperature gradients must not be ignored."

Jan 1, 2001

By Avijit Moitra

The behavior of the solidifying shell in the early stages of solidification has an important influence on the final quality of continuously-cast steel slabs. In order to understand the thermal and mechanical behavior of the shell, a two-dimensional transient piecewise-coupled finite-element model has been developed. The model simulates a transverse section of the slab as it moves down through the mold and incorporates the effects of heat conduction, solidification, shrinkage, turbulent fluid flow, thermal distortion of the mold and the visco-plastic behavior of the steel. Coupling between the thermal and the mechanical model is based on the mutual dependence of heat transfer across the interface between the shell and the mold and the size of the gap. The effects of mold distortion and taper on the gap size are also included. The effect of fluid flow has been incorporated via a heat flux imposed at the solid-liquid interface, which is obtained from a separate fluid flow model. The high temperature creep and plasticity of the steel is incorporated through a unified constitutive law defining the inelastic strain rates as a function of temperature, time and stress state. The model can be applied to various problems in continuous casting, such as the formation of surface defects and the design of mold taper.

Jan 1, 1992