Search Documents

By L. Yuan, J. H. Rowland III

"In 1995 and 2003, the Mine Safety Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) being used in underground coal mines in the United States. The survey reports showed data for the different AMS manufacturers, the different types of equipment monitored, and the different type of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along the belt haulage entries. As of December 31, 2009, point-type heat sensors were prohibited for use for an early fire detection system; instead carbon monoxide (CO) sensors are now required. This report will examine the number of AMS currently used in underground mines in the United States to see if there is a change in their use. The locations and parameters monitored by AMS are also discussed. INTRODUCTION The last survey conducted by the Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems (AMS) used in underground coal mines in the United States (US) was in 2003 [1]. The survey report states that since 1995 there had been a steady increase in the use of AMS in underground coal mines as the technology of CO sensors was improved by manufacturers. AMS had become more reliable and some CO sensors could be purchased with the capability to discriminate between the CO produced from a fire versus CO produced from diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed for the miners to take the necessary action to put out the fire or exit the mine. It should also be noted that at the time of last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than using point-type heat sensors [2]. Finally, since the last MSHA survey, regulations have changed on the type of automatic fire detection systems permitted to be used in conveyor belt entries. As of December 31, 2009, point-type heat sensors are not permitted to be used for fire detection in underground coal mines in the US; instead CO sensors are required as a replacement (30 CFR 75.1103-4). This study will examine how the changing of the above regulations has impacted the use of CO sensors in underground coal mines in the US compared to their use based on the last MSHA survey. Importantly, in the previous MSHA survey, the data was recorded for producing and non-producing coal mines. In this study, only the data from the producing coal mines was recorded. Data was collected from a total of 235 coal mines for this study with the help of the MSHA district offices."

Jan 1, 2017

By J Abols, T Hughes

The selective recovery of gold and silver from solutions containing other metals, such as copper, is possible using AuRIX«100 resin in conjunction with the Gekko Resin Column. Selectivity is driven by controlling the solution pH, which enables activities such as loading copper, gold and silver and then selectively stripping copper before gold and silver. Alternatively gold and silver can be loaded and the copper left in solution. The selective loading of gold while reducing the silver loading has also been demonstrated, opening the possibility of producing high grade gold dorT from high grade silver pregnant leach solutions. This paper reviews the AuRIX«100 resin and Gekko Resin Column Technologies, discusses the uses of AuRIX«100 in the recovery of gold and silver and the chemistry relating to several projects for which AuRIX«100 is being tested.

Jan 1, 2005

By Tim Hughes, A. H. (Sandy) Gray, Jennifer Abols

"The selective recovery of gold and silver from solutions containing other metals such as copper is possible using AuRIX®100 resin in conjunction with the Gekko Resin Column. Selectivity is driven by controlling the solution pH, which enables activities such as loading copper, gold and silver and then selectively stripping copper before gold and silver. Alternatively gold and silver can be loaded and the copper left in solution. The selective loading of gold while reducing the silver loading has also been demonstrated opening the possibility of producing high grade gold doré from high grade silver pregnant leach solutions. This paper reviews the AuRIX®100 resin and Gekko Resin Column Technologies, discusses the uses of AuRIX®100 in the recovery of gold and silver and the chemistry relating to several projects for which AuRIX®100 is being tested.INTRODUCTIONGekko SystemsGekko Systems specializes in the design, development and distribution of innovative mineral processing equipment and systems with a particular focus on gravity separation for the gold and diamond industries. The company, which has been around since 1996, has five main products: the InLine Pressure Jig, the InLine Spinner, the InLine Leach Reactor (ILR), Gekko Resin Column and Modular Systems.The InLine Leach Reactor is an intensive cyanidation reactor that uses high cyanide (0.5 – 2 % NaCN) and high oxidant (20 ppm dissolved oxygen as O2 or hydrogen peroxide) to dissolve gold from medium and high-grade gravity or flotation concentrates. The ILR, which typically replaces a shaking table in the gold room, is available in both batch and continuous models. There are 42 installations worldwide. Further details on this technology can be found in papers written by Gray et al (2003) and Longley, McCallum and Katsikaros (2003). By replacing a shaking table with an ILR, the overall gravity and plant recoveries can be increased significantly. Other advantages include reduced security risks, lower operating costs, reduced operator involvement due to the automatic process and increased safety for gold room operators."

Jan 1, 2006

By Noakes M. J

Research and development into alternate gold and precious metals adsorbents has resulted in the development of a new technology named the AUROSAVE adsorption process (ARGOSAVE'" for high silver con- tent ores). Adsorbents called VITROKELE'" can be tailored for either Gold I (cyanide leach) or Gold III (halide leach) applications. VITROKELE consists of a chemically synthetic adsorbent carried on an inert substrate, often a polystyrene bead. It is suitable for both in- pulp and in-solution use. VITROKELE adsorbent offers certain advan- tages over both carbon and ion exchange resin adsorbents. This paper describes testwork on Australian ores and commercial solu- tions obtained from operating Australian plants demonstrating the kinetic loading characteristics, elution methods and other operating parameters of VITROKELE adsorbent in the cyanide system. Brief reference is made to VITROKELE in the Gold III system.

Jan 1, 1988

By K. R. Robilliard

The Peru based tin mining company, Minsur S.A., commissioned Ausmelt Limited to design, supervise construction and commission a tin smelter and refinery for production of refined tin metal. The plant is located 240km south of Lima, near Pisco, Peru and is operated by Funsur S.A., the wholly owned subsidiary of Minsur S.A.. Selection of the Ausmelt Technology followed a series of crucible scale test work and pilot plant trials conducted at Ausmelt's facility in Dandenong, Australia and two feasibility studies undertaken by Ausmelt in 1991 and 1993. Ausrnelt began the plant design in 1994 with the construction phase following in 1995. Commissioning of the plant commenced early in 1996 with a target throughput of 30,000 tonnes per annum of concentrates. In mid 1998 oxygen enrichment of the Ausmelt lance air was introduced to expand the capacity to the throughput of 40,000 tonnes per annum of concentrates. The process route involves the use of an Ausmelt furnace for primary concentrate smelting, followed by a conventional tin pyro-refining circuit to produce high grade tin suitable for sale. Further work continues between Ausmelt and Funsur to investigate the use of an alternative, more economical, fuel source and the installation of a second Ausmelt furnace. The paper reviews the project to date with details of ongoing operations and developments at the Minsur Tin Smelter.

Jan 1, 2000

The Use of Automated Mineralogy to Interpret the Batch Flotation Performance of Merensky Reef Ore

Sep 13, 2010

By D. McConchie

The use of Bauxsol? (physically and chemically modified alumina refinery residues) to treat acid rock drainage (ARD), and sulphidic waste rock and tailings, provides new options for managing some intractable environmental problems at both derelict and active mine sites. Treatment of ARD waters using the Bauxsol technology shows that the effectiveness of raw Bauxsol material can be enhanced by including modest amounts of selected industrial minerals or common chemical additives. The type and amount of additive required and the amount of the blend needed to treat the water depends on the initial composition of the water and the target water quality; for some ARD waters, optimum treatment may require one or more changes in the type or amount of additive used. Maximum treatment efficiency can be achieved only when a balance is maintained between the rate of trace metal binding and the rate of change in water pH; adding treatment reagents faster than can be accommodated by the reaction kinetics will not result in more rapid water treatment. This paper presents the results for treating several ARD waters to illustrate the importance of blend selection and treatment procedure. Although treating ARD water is often necessary, this strategy treats the symptoms rather than the cause. The best permanent solution is to treat the sulphidic waste rock or tailings such that they do not continue to oxidise and produce acidic metal-rich leachates; sulphide oxidation needs to be stopped or slowed to a rate that can be accommodated by normal environmental processes. Capping lined impoundments is not a solution because all caps and linings will inevitably fail some time in the future creating a nasty surprise for some future generation. Adding lime is also less than ideal because the lime leaches from the treated material; treatment often appears to be effective for a few years and then fails. Bauxsol technology offers effective alternatives to conventional liming and capping procedures and Bauxsol blend application rates and procedures can be planned to ensure that no acidic or metal-rich water can ever escape from the site. Bauxsol can be physically mixed with the sulphidic mine wastes or it can used to form subsurface permeable reactive barriers, or both. Bauxsol treated waste rock and tailings can be immediately and effectively revegetated. In this paper we present leachate quality and plant growth rate data for several sulphidic waste rock and tailings deposits treated using the new technology.

May 1, 2003

By John Hughes

Fundamental to the use of rotary bit drilling equipment for oil and gas drilling is the requirement to maintain a cooling and lubricating environment for the bit and a means of conveying the cuttings from the drilling operation to the surface. The vast majority of such functions are provided for by the use of water based drilling fluids, commonly known as the drilling mud. One of the basic constituents of drilling mud is bentonite, a montmorillonite clay. Bentonite, when mixed with water at approximately 6% solids, will produce a fluid which has several important features in connection with its role as a drilling mud:

Jan 1, 1983

By Hector Simchas

"1. BENTONITE: THE CRUCIAL CONSTITUENT OF SLURRYSuspensions of bentonite and water are used in a variety of applications in underground engineering. For the construction of underground elements like slurry walls or piles, bentonite slurries offer support to the excavation of loose soils and counter pressure against hydrostatic pressure of ground water, especially where soil permeability is high. In addition, for the construction of tunnels by the slurry-shield method or when hydromills are used for excavation, bentonite suspensions transfer the loosened soil to the surface. In applications like pipe jacking and microtunneling, or where high revolution drilling is required, bentonite also provides lubrication and cooling.To fulfill these functions, the properties of a bentonite slurry need to remain stable, or at least predictable, during the course of construction. Unfortunately, when a suspension mixes with earth, ground water and/or impurities, its properties may be compromised resulting to reduced performance, which would in turn lead to increased construction costs and the risk of the excavation collapsing. Our experience in the lab and onsite is presented herewith.2. MOST USUAL FACTORS OF PERFORMANCE FAILUREWater and soil quality are important factors defining the behavior of suspensions. In an extensive program of measurements in our technical laboratory, the effect of frequently encountered harmful substances on bentonite suspensions has been examined and the results are summarised in Table 1.Some tests show that the conductivity of water has a direct relationship with Marsh Viscosity. For example, we have seen that if the quantity of bentonite required to achieve a 40s Marsh Time ranges between 50-52 kg/m3 at water conductivity below 100 µS/cm; when conductivity is increased to 1,400 µS/cm, we need 65-68 kg/m3 in order to achieve the same property."

Jan 1, 2015

By J. Jacob, A. G. Guézennec, F. Savreux, S. Nanaa, M. Delclaud, P. d’Hugues

Mining wastes can contain base and precious metals, but also metalloids and rare earth elements that are nowadays considered as highly critical for the industrial development of the European Union. The development of alternative routes to conventional processing is still required in order to decrease the cost associated with the treatment of these resources, which are more complex in composition and with lower grades. An ecologically acceptable and yet economic alternative for processing of low-grade sulphidic primary ores as well as mining wastes is the extraction of metals using bioleaching processes. The purpose of this study was to test the potential of bioleaching procedures for the extraction of residual metals contained in sulphide-rich tailing wastes coming from a European copper mine. These wastes are mainly composed of pyrite (60%) and contain cobalt (0.06 %) and gold (0.95 g/t). Bioleaching experiments were performed in 2 L stirred reactors in batch mode and in pilot tanks (110L) in continuous mode, using the "BRGM-KCC" bacterial consortia. High metal extractions were obtained (cobalt dissolution > 90%), which confirm that bioleaching is an effective process for this tailings material. Experimental results were used to design a global treatment process scheme and to perform a preliminary economic evaluation, showing good profitability of a hypothetical industrial project.

Jan 1, 2014

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

Past and present developments in the use of blast furnace slag in the manufacture of glass are outlined. The crude slag from Port Kembla is beneficiated by the Mineral Resources Division of Australian Consolidated Industries Ltd. at Mascot using a dry magnetic separation process which reduces the iron level in the slag to an acceptable value, The chemical and physical properties of both the crude and beneficiated slag are given and compared with those of other slags used in the manufacture of glass. Slag is added to intro- duce alumina into the glass and its addition to the glass batch also results in faster melting and refining. Slag was first used in Australia in 1968 and its use has increased steadily year by year. At present about 16 000 tonnes of slag are used per year, mainly in amber and white glass. Beneficiated slag is used'in three plants to supply all the alumina required in the amber glass and in four plants to supply part of the alumina required in the white glass, the amount added depending on the acceptable iron level in the glass. Slag is also used in limited quantities in the manufacture of both dark and light green glass.

Jan 1, 1979

By Andrea Brickey, Ethan Marcoux

The South Dakota School of Mines and Technology (SD Mines), located in Rapid City, South Dakota, is one of only a few universities in the United States that offer a Bachelor of Science in Mining Engineering. The Department of Mining Engineering and Management (MEM) at SD Mines teaches courses that introduce students to concepts related to mining, including a course covering explosives engineering. Students are taught the basics of explosives theory and application in the mining and construction industry through a series of lectures and assignments. With limited field experience, many students find some topics difficult; these include: flyrock, ground vibration, timing, and others. Some US mining schools have an experimental mine in which they can simulate field conditions and conduct hands-on training, but not all universities have such facilities. For those without, teaching certain concepts can be more challenging in a pure classroom environment. To counteract the lack of an experimental mine, the mining department at SD Mines implemented Paradigm (Version 18.4.4984.0; McKenzie, 2017) a computerbased blast modeling software to improve the learning environment.

Jan 1, 2019

By J C. Diaz, C R. Scherpenisse

Blasting represents one of the most relevant unit operations in the process of mineral extraction. The final objective of this operation is that of obtaining an adequate final fragment size distribution such that the combined costs of drilling, blasting, excavation and transport, and crushing/grinding, are minimised, while at the same time producing the minimum possible level of damage to the surrounding rock mass. The strong influence that drilling and blasting has over the subsequent processes involved in the operational cycle makes it imminently desirable to have access to experience and technology which make possible the evaluation and optimisation of this unit operation. The correct use of vibration monitoring techniques offers a number of benefits in terms of their ability to examine any blasting process in detail. In effect, the measurement of particle velocity levels that result from the detonation of each explosive charge offers a means by which it is possible to measure relative efficiency of each charge, interactions (productive and counterproductive) between adjacent charges, and a definitive indication of general performance of any given blast design and its implementation. In this way the monitoring of blast vibrations in rock due to the blast event, can be used as a diagnostic tool, given that the correct interpretation of the vibration traces allows the determination of the level of interaction between the design and operational variables of the blast event. This makes it possible to evaluate, for example, the presence of out of sequence detonations, statistical scatter in the detonation times of pyrotechnic delay detonators, deficient detonation of charges, instantaneous detonation of charges and sympathetic detonation of charges, as well as the general of vibration levels in terms of peak particle velocity, acceleration, and displacement. Another important use of such data is in the construction of a database relating vibration levels to charge weight, hole diameter, and distance, for any given rock type, enables the calibration of predictive vibration models which in turn make it possible to predict the damaging effects of blasting. Knowledge of both the vibration levels induced, combined with quantitative measures of the geomechanical competence of a rock mass make it possible to estimate the probability of producing blast induced damage. The high levels of vibration generated by some blast events may damage the rock mass, producing new fractures or extending and dilating existing fractures. The vibration in this context may be considered as a dynamic stress provoking strain in the rock mass. This paper describes the application of the vibration monitoring technique, particularly in the underground mining environment, and its importance in diagnosis, modelling, control, and optimisation of the development blasting process. The potential of the technique is assessed in the context of achieving substantial techno-economic improvements development blasting results, increasing output whilst minimising the operational costs of the mining process.

Jan 1, 1999

By Paine GG

In coal mining each of the unit operations are interrelated with each preceding operation having an effect on subsequent operations. This presents difficulties for determining when the lowest overall costs for a particular mining system are achieved. Drilling and blasting is the first mining operation for production and is known to have an effect on the subsequent loading, hauling and crushing operations. Computer blasting models developed over the past 15 years can be used to describe the drilling and blasting operation. This paper describes the ICI Blasting Model "SABREX" in detail. Methods of using the model are discussed. This involves field measurements of geological structure, shallow refraction seismic surveys, laboratory measurements of rock properties and high speed photography of blasts. The predictions are compared with actual blast results for fragmentation sizing and muckpile profiles. Outputs from the model are described and these can be used for input to models of subsequent operations.

Jan 1, 1987

After the minim operation, most raw materials that occur in the earth's crust require some form of processing or refining before they can be converted into a final end product. In the mineral industry these remarks apply to materials such as iron ore, bauxite, limestone, copper ore and many others that are found in Australia in large quantities. Processing plants for these raw materials operate more efficiently, however, if the feed to them is consistent in both physical and chemical characteristics. Such uniformity rarely occurs in nature so that some form of homogenisation, or blending, is required ahead of the processing plant. Bending also assists the mining operation itself by reducing; the need for selective mining and, by combining high and low grade materials, a more uniformly graded, commercially acceptable product can be obtained, thereby increasing the commercial life of a mine or quarry. Bed blending is the most efficient of the processes available, and following its development in the United States in 1905, over 100 plants have been installed, or are under construction, all over the world. The original process, the Robins--Nessiter system, has been the subject of continued improvements and refinements, so that economical capacities are possible from less than 100 l.t.p.h. up to 10,000 l.t.p,h. and beyond.

Jan 1, 1969

By George C. Carter

It was just a little over three years ago that the "Go" button was pushed to start operations on the blending piles at Oro Grande. As is usual with any new installation, there were problems that had to be solved. This paper will concern itself with those problems directly related to quality control. To obtain a consistent outgoing quality level at the most economical level for a finished product requires two main points: 1. Measurement of variations in the process, 2. A method of making a predictable change to adjust for variations. The manufacture of cement requires a relatively high degree of accuracy if a consistent outgoing quality level is to be maintained. The blending piles were our solution to this problem.

Jan 1, 1962

By Ron Robinson

Booster fans have been in regular use in British coal mines since the first half of this century, but a large increase in their use did not take place until after the Nationalization of coal mines in 1947. From that time the need was identified to improve standards of ventilation in general and mining engineers specializing in ventilation were appointed at all levels in the mining industry. A comprehensive approach to ventilation surveys and planning, together with the realisation of the benefits of booster fans, led to their more rapid introduction. Many coal mines in the U.K. are at moderate depth and have virgin strata temperatures of 30°C or less. The ability to control climatic conditions by increased ventilation rather than resort to cooling systems has led to the introduction of booster fans and recirculation systems in these mines. Large makes of methane and high levels of coal dust production due to increased mechanization have also required enhanced ventilation standards. This paper deals with the reasons for selecting booster fans and the specific safety considerations involved in their use. Numbers, types and sizes of booster fans in the U.K. are outlined, together with notes on installation and performance. Remote monitoring and control from the surface is dealt with, and current legislation. The evolution of controlled recirculation is also covered starting with auxiliary fan systems in 1970 and leading to very large district schemes in the late 1980s. The research at Newcastle upon Tyne University and other establishments in the climatic conditions associated with recirculation is summarised and its use in assisting existing and proposed conventional and recirculation systems is indicated.

Jan 1, 1989

By D. M. Schubert

As a clean and renewable energy carrier, hydrogen is an important component of most alternative energy portfolios. Hydrogen combines very high energy content by weight with excellent environmental attributes. Since hydrogen reacts with oxygen to produce only water with release of energy, it can be used to power fuel cells, combustion engines, and turbines, without production of greenhouse gases at point of use. However, because of its low volumetric density, storing pure hydrogen is impractical. Thus implementation of hydrogen technologies requires materials that can safely store and release large amounts of hydrogen (1,2). In recent years, the U.S. Department of Energy (DOE) and other governmental agencies around the world sponsored extensive research on hydrogen storage materials, including those based on boron. These efforts have resulted in significant advances in hydrogen storage technologies. Boron materials stand out as leading candidates for hydrogen storage among the many options investigated. Combining excellent hydrogen densities, release rates, and safety characteristics, some boron materials can hold substantially more hydrogen by weight and volume than even pure liquid hydrogen (3-5).

Jan 1, 2010

By Rodney H. Sergent

After being forgotten or ignored for nearly 100 years, the ability of bromine chemistry to extract gold from ore has been rediscovered. While bromine chemistry is similar to chlorine, there are some important differences. Bromine in its elemental form is a dense, fuming, red liquid. Elemental chlorine is a gas and requires a substantial amount of equipment to handle, store and deliver to solution. Bromine has an advantage in its ability to rapidly and completely oxidize heavy metals to water soluble halide salts. The first patent for use of bromine chemistry for gold extraction was issued in 1881 (1). By 1895, work done in Colorado concluded well roasted ores required approximately 1-1/2 lbs/ton of elemental bromine for superior extraction of metals (2)). At that time, bromine was deemed to be cost effective vs. chlorine even though it was more expensive on a pound basis than chlorine. The advent of cyanide technology virtually eliminated both chlorine and bromine from consideration for leaching of ores. Cyanide was so inexpensive that it made deposits requiring unique technologies unattractive for mining. Only since the deregulation of gold price has bromine/chlorine technology been considered for those ores not amenable to cyanide. While chlorine has found its way into the pretreatment steps, bromine is just beginning to realize its niche in the marketplace.

Jan 1, 1998