Search Documents

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec's first diamond mine by 2013.

Jan 1, 2010

By Tom Hanke, Joe Strobbe

The 80 year old Theodore Roosevelt Dam built in a scenic canyon near Globe, Arizona is currently undergoing a major renovation. The old stone dam, built by hundreds of skilled stonemasons, is being covered with a new concrete face that will increase the dam height by 77 feet. The renovated dam will improve flood control and provide increased electrical power and recreation area. The contractor, J.A. Jones is constructing the new dam and powerhouse for the Bureau of Reclamation.

Jan 1, 1993

By R. M. Kleine

In the fall of 1968, Sheridan Geophysics leased the Renzy Mine property 50 miles northwest of the town of Maniwaki, Quebec. A 500-tpd flotation mill was dismantled at Belleterre, Quebec, trucked into the mine over a winter road and re-erected during extreme winter conditions. Approximately one billion gallons of water were removed from Renzy lake to expose the orebody. A 3,000-hp diesel generating plant and a self-supporting community were set up during the early part of 1969. This was a remark-able achievement considering that most of the work, including the pouring of foundations and the draining of the lake, had to be done during the winter months. Despite this, the project was completed ahead of schedule and one million dollars below budget. The mill is now treating an average of 800 tpd.

Jan 1, 1970

By J. Dorsey

In 1910, Colonel Boyce Thompson, who owned Inspiration (now Cyprus Miami) and various other mining interests, formed the Magma Copper Company and leased the Silver Queen claims around Superior, Arizona. At the same time, he purchased other claims around the Silver Queen claims from what was then called the Magma Mine. The mine continued to operate until 1982 when Newmont Mining Company, who owned Magma Copper Company, shut down the operations due to high costs and low copper prices. When Magma was spun off by Newmont as an independent company in 1987, new studies of Superior were started. It was clear from these studies that the mine had been shutdown and over 1400 employees laid off for two basic reasons: first, as a resu1t of a mine plan that was technically flawed and second, be-cause of very high production costs mainly due to the low productivity from a very high cost work force. During 1989 a plan was formulated to re-open Superior with the determination to over-come the problems that resulted in closure. A new mine plan was developed and a management style developed that promotes team work and high productivity.

Jan 1, 1992

By A. Thoraval, K. B. Slimane, O. Ozanam

The REP experiment is part of the research programme conducted by Andra to investigate the possibility of reversible radwaste disposal in a Jurassic (Callovo-Oxfordian) argillite formation at the Meuse/Haute-Marne underground laboratory site in northeastern France. The experiment focuses on the hydromechanical response of the formation to sinking the laboratory access shaft. Modelling of boreholes and shaft sinking operations has helped to optimise measurement point locations based on initial stress tensor anisotropy, while minimising interaction between instrument boreholes. Analyses were made of model sensitivity to intrinsic rock characteristics, hydromechanical coupling properties and sensor installation procedures. L’expérimentation REP fait partie du programme de recherche pluridisciplinaire engagé par l’Andra pour étudier la possibilité d’un stockage réversible des déchets radioactifs dans la formation Callovo-Oxfordienne des argilites du site de Meuse/Haute-Marne (Commune de Bure - France). Cette expérimentation permettra d’étudier la REponse hydromécanique de la formation aux sollicitations engendrées par le fonçage du Puits d’accès du laboratoire souterrain de recherche. Afin d’optimiser le positionnement des points de mesures, compte tenu de l’anisotropie du tenseur des contraintes initiales, et de minimiser les interactions entre les forages d’instrumentation, des modélisations des forages et du creusement du puits ont été conduites. Des analyses de sensibilité aux caractéristiques intrinsèques de la roche, aux propriétés de couplage HM et aux protocoles d’installation des capteurs ont été faites. Die REP-Untersuchung ist Teil des multidisziplinären Forschungsprogramms, das die ANDRA im Callovo-Oxfordian-Tonstein in situ am Standort Meuse/Haute Marne (Gemeinde Bure – Frankreich) im Hinblick auf eine Eignung zur reversiblen Lagerung radioaktiver Abfälle durchführt. Dabei soll das hydro-mechanische Verhalten der Formation auf die Beanspruchungen, die durch das Abteufen des Zugangsschachts zum Untertage-Forschungslabor erzeugt werden, untersucht werden. Zur optimalen Positionierung der Messpunkte unter Berücksichtigung der Anisotropie des Tensors der Ausgangsspannungen und zur Minimierung der gegenseitigen Beeinflussung der Instrumentierbohrungen wurden ein Schachtabteuf- und Bohrmodelle entwickelt. Zur Untersuchung der inhärenten Eigenschaften des Gesteins, des gekoppelten HM-Verhaltens und der Installationsprotokolle der Messsonden wurden Sensibilitätsanalysen durchgeführt.

Jan 1, 2003

By H. Thomasson

THE war, like all destructive agencies, has focused attention on salvage and conservation, and to such an extent that a decade of normal progress has been crowded into a few months. This is particularly true as regards the repair of cutting tools. As a consequence, there has arisen a wide demand for comparable data by those engaged in such work, and for basic information by others who wish to repair tools. These repairs may be grouped in three classes: (1) The repair of broken tools of relatively slender cross-section, such as broaches, reamers, drills, etc., of a type that could be returned to service if a means to join the broken surfaces were available, as fortunately it is in the low-temperature silver solder process; (2) the repair of tools that possess shanks, tangs, and other non-cutting portions that may be broken or damaged to the extent that only the addition of metal will permit their return to service; and (3) the repair of special rotating tools, such as end-mills and milling cutters, that may have portions broken from the cutting edges or have their edges so worn in service as to require building up.

Jan 1, 1943

By P. S. Pashkovsky, S. N. Smolanov

The essence of the method consists in creation of drop of opposite sign at the isolating stoppings, by which air losses through the accident district change direction of their motion. The period of reversal is selected in that way so that air may not find itself in the zone of burning. The method of fighting the fire considered was repeatedly used in the coal mines of the Ukraine. The theoretical basis of efficiency and two examples of use of this method by fighting the underground fires are adduced in the paper.

Jan 1, 2003

By E. L. Atkinson, G. W. Leach

The paper discusses the reasons for the introduction of load-haul-dump (LHD) units into Greenside Colliery, and the circumstances leading to the replacement of conventional mechanized equipment on a trial basis in the mining operations on No. 2, 4, and 5 seams. An outline is given of the factors governing the selection and introduction of these units into coal mining, and the associated mining and engineering aspects involved in the optimization of their use. Operating statistics comparing the performance of conventional and LHD equipment are included.

Jan 1, 1979

By A. V. Glembotsky, N. A. Greshnova, V. P. Seregin, V. A. Glinkin

Based on a new alternative depressant of zinc sulphide - dimethyldithiocarbamate- modern technology has been developed for the treatment of complex polymetallic ores. In addition to its general function (depression of sphalerite and iron sulphides to some extent), this double-acting reagent is a promoter for galena and silver minerals. Laboratory and plant tests, as well as industrial experience have all shown consistently higher silver recovery to the lead concentrate as compared with sodium cyanide, resulting in less pollution and a safer environment

Jan 1, 1995

By J. Owens

The methodology of quarrying changed significantly in the Indiana Limestone industry in the sixty years between September 11, 1941, the date of the Pentagon groundbreaking ceremony and September 11, 2001 when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on September 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction (and Indiana Limestone) industry can accomplish when working toward a common goal.

Jan 1, 2004

By H. N. Wolcott

AMONG the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It, therefore, seemed to the writer that the case described below was worthy of record. FIG. I.-GROUND MASS OF CHALCOPYRITE (C) CONTAINING ROUNDED GRAINS OF PYRITE (P) SHOWING DIFFERENT DEGREES OF REPLACEMENT BY QUARTZ (Q), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town Mine, in Russell Gulch, and are in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy- rite, with some grains of tetrahedrite. The polished surface of some of

Jan 6, 1917

By J. A. H. Church

The report is too voluminous to be considered in detail within the scope of a single paper, so I will confine my consideration of it to the broader aspects, leaving other members to deal with points of particular interest. The method of presentation leaves one with an uneasy sense of prolixity and confusion of thought; the foreword by the Chairman may well be accepted as a true index of the whole. His argument amounts to this: Recognizing at the outset the futility of divided counsels, it was deemed advisable to arrive at unanimity. To this end, some members subscribed to views to which they do not whole-heartedly assent, thus giving weight to conclusions with which they were at variance. Unanimity cannot be qualified-either it exists or is absent-and, moreover, in the text of the Com-mission I can find no word that unanimity is required. Surely it would have been preferable to have a unanimous report covering such aspects as were acceptable to all members, with minority reports by individual members on such other aspects as were controversial, leaving it to the Government to give such weight to the divergent views as the personality of their sponsors might warrant. In the final analysis the value of an opinion varies directly as the personality of its exponent.

Jan 1, 1926

By Warren C. Bracewell

At your request, am submitting to you several suggestions for the amendment of our safety code which you felt should be kept up to date. These suggestions are the individual opinions of the several members of the Committee who have expressed (heir wishes to me in the form of letters. I am particularly indebted to Mr. Daniel Harrington, Mr. Wm. Littlejohn, Mr. Warren Bracewell, Mr. James Dalrymple and Mr. Hugh McLeod. Would recommend the following amendments Section 1. Wherever practical trolley wires should be securely hung to roof or timbers at a distance of not less than five feet and not more than six and one-half feet above rail and six inches to one side. Spacing of hangers should be from 20 to 25 feet apart. (Adopted.) Section 2. 500 volts D. C. should not be allowed in any installations. Trolley wires should not carry a voltage of more than 250 D. C. nominal voltage. (Referred back.) Pumps, mining machines and other small machinery units where A. C. power is used should not carry a voltage of more than 220. Large units, such as pumps, motor generator sets and hoists, may use a volt- age of 2,200. When power cables to operate same are of armored construction, cables should be securely buried at all crossings, on haulage-ways or where men travel. (Adopted.) Section. 4. Where power lines pass through door frames or stop- pings they should be properly insulated with porcelain compound or rubber tubing. Wherever men get on or off man-trips in vicinity of trolley wires same should be secure1y guarded and should also be protected with a cut- out switch, same to be pulled before men are allowed to get on or off trips. (Adopted.)

Jan 1, 1926

By CADEN VITTI, Barbara J. Arnold

Mine tailings, the byproduct of mining and mineral processing, are increasingly mass produced as a result of increased demand for metals and minerals as well as the advancement in technology that allows for the exploitation of lower-grade ores. Lower grades can increase the volume of tailings that may contain new gangue minerals that should be evaluated for the presence of critical minerals and other valuable metals. The practice of reprocessing, while relatively new, is crucial to reducing environmental damages, obtaining valuable critical minerals from waste, and contributing to more sustainable repurposing and disposal methods. With the increase in tailings dam failures in recent years, there is a large motivating factor in remining and removing the potential hazard to benefit the safety of potentially impacted communities. In analyzing the perspectives of various domestic and international studies, this literature review will determine the feasibility of reprocessing and reutilizing mine tailings waste for a more sustainable future while exploring current practices that have benefitted ecosystems and communities.

Jan 1, 2022

By CADEN VITTI, Barbara J. Arnold

Mine tailings, the byproduct of mining and mineral processing, are increasingly mass-produced as a result of increased demand for metals and minerals as well as the advancement in technology that allows for the exploitation of lower-grade ores. Lower grades can increase the volume of tailings that may contain new gangue minerals that should be evaluated for the presence of critical minerals and other valuable metals. The practice of reprocessing, while relatively new, is crucial to reducing environmental damages, obtaining valuable critical minerals from waste, and contributing to more sustainable repurposing and disposal methods. With the increase in tailings dam failures in recent years, there is a large motivating factor in remining and removing the potential hazard to benefit the safety of potentially impacted communities. In analyzing the perspectives of various domestic and international studies, this literature review will determine the feasibility of reprocessing and reutilizing mine tailings waste for a more sustainable future while exploring current practices that have benefitted ecosystems and communities.

In most States of Australia it is a legislative requirement for underground mines to have a separate means of egress from the normal means of ingress to permit the safe evacuation of workers to the surface in event of an emergency. Such egress may be in the form of a ladderway equipped shaft/underlie or trafficable incline/decline. Additionally, there is a general requirement to have one or more airways, separate to the main shaft or other principal entrance of an underground mine, extending to the lowest level to permit ventilation to all parts of the mine. Fulfilling these requirement is difficult in the development phase of a mine when access underground is achievable by only a shaft or decline in the process by being sunk. What is frequently practiced in Australia is for production to then commence, sometimes in association with continuing development, in the same configuration without the establishment of this separate method of egress to the surface nor additional airway/s with reliance on refuge chambers to cater for back up in any emergency. Not only, could this jeopardise the health and safety of workers in case of an underground emergency it could be construed as a statutory breach of legislation. While recognising that refuge chambers are often used throughout underground operations nowadays their equipping and the criteria for their location needs to be bought into focus. This presentation discusses how such legislative requirement can be met alongside the use and appropriateness of refuge chambers.

Jan 1, 1998

By H. A. D. Kirsten

The skills differential between manpower supply and demand is due to deeply rooted socio- and politico-educational misconceptions that can be remedied only by a concerted cooperative effort on the part of the general public, the State, organized industry, organized engineering, and engineering education. This will require the general public to recognize that the reasons for the shortages in engineering manpower should be regarded as critical. Public perceptions of engineering, of the vocational and educational prospects in engineering, and of the skills required are poor. The spectrum of engineering vocations, the corresponding function profiles, the interaction between the vocations and the relative proportions of the vocations in the engineering team are in general not adequately appreciated. The recruitment and training of students and teaching staff, teaching facilities, educational curricula, practical training, qualifications, professional registration, and financing are aspects of engineering education that should be brought to the attention of all concerned. . In addition, the educational curricula for the various vocations need to be specified clearly and definitively if the overall mission of engineering education is to be properly appreciated. The uncertainties between university and technikon education and the pursuant vocations need to be resolved. This can be done only by defining the respective curricula in terms of the mental skills and scientific techniques required. The remedial actions with regard to the rationalization of engineering education comprise informing of the public; establishment of an active political lobby; revision of existing education policy; rationalization of existing educational infrastructure; promotion, development, and guidance of engineering student intake; financing of engineering education; accelerated creation of new employment opportunities; and monitoring of the supply and demand of high-level manpower. The parties required to nitiate these remedial actions are various State departments and corporations involved in engineering and industry, various departments of education, the Directorate of Technology of the Department of Trade and Industry, organized engineering education, organized engineering, organized industry, and the Human Sciences Research Council. Only if these interest groups actively initiate the various actions under the coordinated guidance of organized engineering wil the required results be achieved. The South African Engineering Association has proposed a comprehensive programme as strategy to solving the problem, and has obtained broad consensus from various State departments, organized engineering education and research, and the private sector. A joint venture between the Foundation for Research Development, the South African Engineering Association, and organized industry has been charged by the State President with the task of launching the programme.

Jan 1, 1991

By H. A. D. Kirsten

Written contribution by L.J. Besaanst I am a Mechanical Engineering Technician (T3), and wish to further my education to at least NHD (T4) level. I read your paper in the Journal of The South African Institute of Mining and Metallurgy with great interest, and must compliment you on its brilliance. However, there are some questions I should like to ask, and certain points I should like to highlight. I should appreciate your comments. Written contribution by J.F. Curtis The comprehensive and finely detailed survey of, and proposals for, engineering education in South Africa reflects the author's wide experience in the needs for, and the provision of, such education. This paper wil make a major contribution to the enhancement of the profession of engineering and the improvement in quality of engineering activities in South Africa. Contribution by G.W. Annandalet I have studied your paper in some detail, and am of the opinion that it makes an important contribution to the topic of the development of technological manpower, which is currently being debated in South Africa at al levels. Debate on this topic has risen above the level of academic discussion; it has been discussed by the Economic Advisory Council of the President, and is being considered at Ministerial level. Author's reply to L.J. Besaans Thank you for your contribution and complimentary remarks. As you have pointed out, there are certainly many aspects that will have to be addressed in the resolution of the crisis in engineering education. I trust that the following comments satisfactorily answer the queries you have raised. Author's General Comments Since publication of the paper, attention has become focused on the provision of employment opportunities an aspect not dealt with specifically in the paper. The following comments serve to indicate some of the directions in which job opportunities will have to be developed in the numbers that will be required.

Jan 1, 1991

By Alder KF

Nuclear power stations to be installed in Australia will be fuelled from Australian resources of raw materials. This will require the establishment of new manufacturing industries and the eventual expansion of established activities, especially in uranium mining and the preparation of precision metal products. This paper presents some predictions of the possible growth of nuclear power installations in Australia. These might amount to 4000 MWE by 1985 and 11,500 MWE by 1990 and towards the end of the century, about 50% of new generating plant might be nuclear. Predictions are given of the demands for materials (uranium and zirconium) and fuel manufacturing services for four reactor systems which might be considered in the programme. - The availability of raw materials and technical capability place Australia in a particularly good position to undertake the manufacture of nuclear fuel'; in addition to satisfying the domestic demand we should actively seek export markets for these products.

Jan 1, 1970

Nuclear power stations to be installed in Australia will be fuelled from Australian resources of raw materials.This will require the establishment of new manufacturing industries and the eventual expansion of established activities, especially in uranium mining and the preparation of precision metal products.This paper presents some predictions of the possible growth of nuclear power installations in Australia.These might amount to 4000 MWE by 1985 and 11,500 MWE by 1990 and towards the end of the century, about 50 per cent of new generating plant might be nuclear.Predictions are given of the demands for materials (uranium and zirconium) and fuel manufacturing services for four reactor systems which might be considered in the programme.The availability of raw materials and technical capability place Australia in a particularly good position to undertake the manufacture of nuclear fuel; in addition to satisfying the domestic demand we should actively seek export markets for these products.

Jan 1, 1971