Search Documents

By Smitham J. B

A selection of Australian washed coal samples was examined to determine the effect of sample hydrophobicity (rank) and particle size on froth stability in the flotation process. The results indicate distinct rank-based variations in froth volume and stability for flotation tests conducted without the use of collector, over a series of particle size distributions.High-rank coals showed a greater tendency to generate stable, high-volume froths than coals of lower rank. Implications for circuit design and operation are outlined.

Jan 1, 1988

By Laura Moore

The southern shoreline of Monterey Bay, extending from Moss Landing to the Monterey Peninsula, consists of sandy beaches backed by an extensive Flandrian and pre-Flandrian dune complex. This length of shoreline, proximal to areas of urban expansion, is currently being considered for development. For this reason, it is extremely important to understand the variability of beach and dune position along this stretch of coast through time. Previous studies of southern Monterey Bay have documented relatively high erosion rates of 2-8 ft/yr due to a net deficit in the sand budget. Although the sediment transport system in this region is not well understood, estimates for the sediment deficit in southern Monterey Bay range from 200,000 to 1,500,000 yd3/yr. A possible cause of the erosional regime in the southern bay is the removal of sediment by coastal sand mining operations. Based on agency reports and mining permit applications, approximate volumes of sand removed by mining range from 300,000 to 450,000 yd3/yr. These volumes are significant when compared with estimated values for the sediment budget deficit. The sand of southern Monterey Bay, a valuable commercial resource because of its hardness, roundness, amber color and range of usable grain sizes, has been removed from the surf zone, beaches and dunes of Marina and Sand City by four companies since 1906. Information regarding the cross-shore location of sand removal and the exact amounts of sand removal through time is proprietary and poorly documented. However, records documenting the time at which each company commenced and terminated mining do exist. This information suggests that the greatest amount of sand was removed between 1950 and 1968 when three mining companies were operating concurrently.

Jan 1, 1994

By D. P. Hatfield, G. de Jager

"Recent developments in image analysis techniques and the power of computer hardware have spurred international interest in the potential uses of image analysis techniques in a range of industrial applications. One of these applications is the control of the complex flotation process. Despite years of work, the flotation process is still poorly understood. Current attempts to control flotation cells focus on consistently duplicating the control achieved by human operators.In human control of flotation two of the dominant visual cues are the froth flow speed and the froth stability. These two factors can be measured and inferred respectively from image analysis of video of the froth surface. Two important hydrodynamic variables for control of the flotation process are the air addition rate and the level of the froth pulp interface.The current work focuses on the relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell. Results are presented that show a strong relationship between flow speed and concentrate yield. These results include tests where the conditions in the cell were not changed, as well as tests involving changes to the cell level and air addition rate. Preliminary results are presented which show a correlation between froth stability and froth percent solids.Future developments of the system will include comprehensive froth texture typing, colour space and stability analyses."

Jan 1, 2003

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By Magnus Evertsson, Rebecka Stomvall, Josefine Berntsson

"Understanding the effect of particle shape on dry rheology is considered to be an important aspect in order to replace natural sand used in concrete with manufactured sand. Crushed particles from solid rock are normally less rounded and have less equally shaped dimensions compared to natural sand. Thus, the flowability and workability of the concrete will be different. In previous research, it has been demonstrated how different crushing techniques affects the shape of the particles. In many cases it is believed that Vertical Shaft Impact (VSI) technology is a way forward to replace natural sand. To be able to study the effect of VSI at the smaller fractions (63-2000 µm) sufficient measurements methods to determine particle shape are required. Optical tools to analyze the aggregates would make it possible to study a large amount of particles at small fractions. The determination of particle shape of aggregates is challenging since the shape is highly irregular and the size span of particles are very large. This study aim to evaluate one of the available optical tools, the Camsizer, for digital imaging determination of shape and size distribution. The available default shape parameters of the Camsizer are studied to understand the meaning of the parameters and their suitability for determining the quality of manufactured sand. To evaluate the capacity to determine particle shape, tests are made with 35 different materials. The results are compared with the dry rheology measured with the standardized "flow cone" test. Dependence has been previously proven between particle shape and the mass flow rate in the cone. Three different shape parameters, aspect ratio, sphericity and symmetry, are studied with the Camsizer and the results are compared with the mass flow rates in the cone. The results indicate a strong linear relationship between the optical parameters and the flow cone test."

Jan 1, 2014

By Cang Daqiang, Bai Hao, Li Ning, Liu Xueting, Lu Xin, Zhao Lihua, Li Hongxu, Wei Wei

"Based on the principle of carbon balance, a model was built to calculate C02 emissions of each process and correspondingly the total course of production in iron and steel making. The data from a typical integrated steelworks in China was applied in the model. The results show that the BF and coking process account for the most emissions. Generally, C02 emissions in integrated steelworks depend on three factors, resources utilization efficiency, energy utilization efficiency and energy consumption structure, which were considered in an equation in this paper. Especially, General Emission Factor (GEF) was proposed to assess the relationship between C02 emissions and energy consumption. The results show that, higher GEF will result in more C02 emissions with the same energy consumption and in iron and steel making, the optimization of energy structure and development of eco-industrial park both have significant benefit on the carbon reduction.IntroductionThe Global Warming resulting from the increase of Greenhouse Gases (GHGs), especially C02, in the atmosphere has become the main reason of global climate change, and the carbon reduction is one of the most important ways for the sustainable development [1]. The iron and steel making is a manufacturing industry based on iron-coal high temperature chemical process, in which plenty of C02 is emitted. According to the data from IPCC (Intergovernmental Panel on Climate Change) in 2001, iron and steel making emitted about 650 million tons ofC02 every year, which is the fourth largest industry of the fossil energy consumption [2]. According to the data from EEA (European Enviromnent Agency) in 2006, iron and steel making is the largest source ofC02 emissions, which accounted for about 18% of the total C02 emissions in European manufacturing industry [3].It is estimated that the application of various well developed energy-saving technology, such as Coke Dry Quenching (CDQ), Top Pressure Recovery Turbine (TRT) and Coal Moisture Control (CMC), can make the C02 emissions reduced by 0.5%-3% in iron and steel making, and the further C02 emissions reduction can be achieved if more new energy saving technology is applied, such as sintering plant heat recovery, electricity generation with steam generated from converter and the various by-products gas and the hydrogen making process from COG[4,5]. In addition, the application of membrane separation technology is well expected in iron and steel making [6]. For example, the application of C02 Capture and Storage (CCS) in blast furnace combined with the Pure Oxygen Top Gas Recycled BF (TGRBF) technology can reduce the C02 ennss10ns greatly by about 50%-60% [4].That is, as a kind of C02 end-treatment technology, CCS applied with other technology of C02 recovery would be more meaningful. Actually, reduction of the C02 emissions by changing the structure of energy consumption and raw materials with new process of iron and steel making, such as direct reduction process or smelting reduction process [4,7,8], is the trend of ferrous metallurgical engineering, which is regarded as a kind of source-treatment technology. In this sense, source-treatment technology is more pivotal for the solution of carbon reduction in the future than the current popular energy saving technology. Hence, it is necessary to build the C02 emissions model based on the iron and steel making process and evaluate the relationship between the energy saving and C02 emission reduction."

Jan 1, 2012

By K. Hodgson, N. C. Joughin

The detailed mechanism of rockbursts and other forms of damage due to rock failure in underground mining is as yet unknown. Studies of the energy changes which necessarily occur when an excavation is made underground seem to provide the best understanding of the phenomena leading to rock failure and damage (see Cook 1). It is common knowledge that the damage and rockburst hazard increases with depth and is greatest at remnants and in regions mined in an irregular manner. The rate at which energy is released as an excavation is enlarged provides an objective parameter to describe mining geometry in terms which are significant to studies of rock failure. In this paper, it is shown empirically that the rate of energy release per unit area increase in the size of an excavation is closely related to seismicity and incidence of damage in the mine. Consequently, it is suggested that the energy release rate is an important parameter in the design of underground mine layouts. Observations were made at two mines: the East Rand Proprietary Mines, Ltd. (E.R.P.M.), at a depth of about 9000 ft, and at Harmony Gold Mining Co., Ltd., at a depth of about 5000 ft. At both of these mines continuous recording seismic networks were in operation. (See Cook and Joughin.3) DESCRIPTION At E.R.P.M. the gold-bearing reef dips at approximately 35 degrees and is presently being mined at depths from 8000 ft to 11,000 ft below surface. The rock surrounding the excavation consists of a very homogeneous quartzite extending far into the hangingwall and footwall. The stoping width is approximately 40 in.

Jan 1, 1967

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By J. Bouchard, R. del Villar, A. Vazirizadeh

"Industrial flotation is a continuous and often multistage process, where particles of a given mineral species (usually the targeted one), present in different sizes, encounter a large amount of gas bubbles (normally air) to produce mineral–bubble aggregates, which are removed from the flotation device (cell or column) as a valuable product (concentrate). The bubble content inside the cell is characterized by the prevailing hydrodynamic conditions (known as gas dispersion variables), which in turn are known to influence the flotation performance. Although most researchers and practitioners agree that the relationship between the hydrodynamic variables and flotation performance exists, the lack of an adequate method foronline measuring the average bubble diameter has prevented such studies.The aim of this study is to apply appropriate hydrodynamic variables for flotation kinetic modeling (as a key feature of flotation performance) for a given introduced particle size distribution (PSD). In this regard, experiments were conducted in a laboratory flotation column (5.6 cm internal diameter for a total height of 650 cm), and mixtures of quartz (hydrophilic gangue) and talc (naturally hydrophobic mineral), classified in four different size fractions. The correlation between the flotation rate constant and given hydrodynamic variables were analyzed. Results suggest that the relative importance of hydrodynamic variables for flotation rate modeling depends on the PSD. Finally the suggested hydrodynamic variables for each of the various particle size-classes considered were used to produce single variable models for the flotation rate constant. INTRODUCTIONIndependently of the prevailing flotation conditions, the mechanisms for bubble-particle aggregation and the residence time of the phases inside the device must also be considered. In this regard, one of the most used approaches to represent the overall flotation process is as a pseudo-chemical reaction between a particle and a bubble, whose rate (at a given time) is proportional to the amount of remaining floatable species. The proportionating constant is called the kinetic constant or the flotation rate constant."

Jan 1, 2016

By Willis I. L, Stevens B. P J, Stroud W. J

The Early Proterozoic metamorphic rocks of the Broken Hill (BH) Block have been recently subdivided into sixteen formations and four groups (Willis et al., 1983b, Stevens et al., 1983). This stratigraphic subdivision has relied upon recognition of distinctive mapped rock units and "associations" of mapped rock units, which characterize particular lithostratigraphic units. The rock units and rock unit associations define local ordered sequences which can be compared and correlated, thereby establishing the stratigraphic succession. In the Clevedale homestead, Thackaringa, BH City, Bores Mine-Freyers mine, Silver King mine, and Brewery Well areas, coherent stratigraphic successions have been interpreted. These areas illustrate the regional variability of the stratigraphic succession and facies changes within individual stratigraphic units. Stratigraphic type sections are located in the Thackaringa, Bores Mine-Freyers mine, Silver King mine, and Brewery Well areas. The principles of stratigraphic interpretation applied in the BH Block can be used in other areas of Willyama Supergroup outcrop such as the Euriowie, Olary and Mount Painter Blocks. The general technique may also have applicability to other highly deformed and metamorphosed terrains.

Jan 1, 1983

By Errol vanHuyssteen

Old tailings from Zn, Au, Cu, and Ni mining operations were characterized. Their mineralogical variation in depth is compared with matching pore water and solids chemistry. A geochemical model was used to predict minerals precipitating from pore water solutions. These are compared with actual secondary minerals occurring. The degree to which the precipitation of secondary minerals controls the sulfate and iron concentration of the pore water was also investigated. The results obtained are related to the selection of the most appropriate modes of tailings deposition.

Jan 1, 1998

Recent geological mapping has indicated changes to the stratigraphy of the Pine Creek Geosyncline. The new stratigraphy and interpreted depositional environments are examined in relation to the distribution and genesis of stratabound mineral deposits. Basinward correlations are made with near-shore carbonate and psammite-rudite units in the Rum Jungle region. Most other units in the same region are condensed, indicating long- lived supratidal, intertidal or shallow conditions during most of the depositional cycle. Units containing most of the mineralisation represent the earliest near-shore developments of strongly reducing partly pelitic and evaporitic conditions and contain mainly uranium and base metals. Restricted distal, strongly reducing facies with associated felsic volcanics are also well mineralised, and mainly contain gold, silver and base metals, although some deposits are probably genetically related to synorogenic or postorogenic granites. Mineralisation in other facies is almost all epigenetic hydrothermal in origin, although minor mineralisation is related to volcanics, or dolomitic parts of the sequence. Areas of potential mineralisation include near-shore environments in the north, and carbonate reefs along growth faults. Two suites of postorogenic felsic volcanics and related sediments deposited in shallow water within and around northwest and east-northeast rift systems, overlie the metasediments of the Pine Creek Geosyncline in the south. The suites have potential for volcanogenic deposits, mostly of uranium, gold and copper.

Jan 1, 1984

By A Maldonado, A Robert, K G. Mercer

The Hamersley Group in the Pilbara, Western Australia, consist of interlayered banded iron formation (BIF) and shale host rock formations within which a large number of open pit iron ore mines have been established. The slope stability of most of the mining excavations developed within these formations is controlled by the relatively low shear strength of the shale groups and shale bands, which are the weakest rock types. Shale formations range from fresh to highly weathered and are generally highly fissile when fresh, and clayey when weathered. An accurate understanding of the shear strength of these materials across the entire weathering continuum is therefore a key importance for assessing the slope stability of these mines.Historically defect laboratory testing results for the Pilbara mines have been analysed mechanically using direct shear testing (DST) to measure a number of geotechnical characteristics of the rock bedding and defects. This paper sets out the current practice in the industry in terms of the laboratory testing and presents a possible application of hyperspectral data to empirically correlate the shear strength of shale bedding with the relative mineralogy abundance on the bedding surface. This was achieved by creating both hyperspectral and geotechnical data sets for the same samples.In the study the shale samples were separated into three distinct assemblages: iron oxide + kaolinite, iron oxide + white mica + kaolinite, white mica + kaolinite, which had 40, nine and two samples respectively. Analysing these assemblages alongside DST data showed that samples with white mica had reduced non-variable shear strength, whereas samples with iron oxide + kaolinite had an overall higher shear strength but with a greater variance. It is inferred that the reduced shear strength in the white mica samples is due to the sheet (or plate) like structure of the mineral, giving it a weak stress plane. Confidence in the trends observed can be reinforced by expanding the data set in future works. The investigation also includes a discussion on weathering grade and addresses the question as to whether mineralogy abundances influence these characteristics in Hamersley shales.CITATION:Maldonado, A, Mercer, K G and Robert, A, 2017. The relationship between mineralogy and shear strength of Pilbara Hamersley Group shales across the weathering spectrum, in Proceedings Iron Ore 2017, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R R. J McAllister, K Moffat, S Heyenga

This paper examines the statistical relationship between quality of life indicators and the gross value of mineral production from Australian regions. We used quality of life indicators, aggregated for 673 local government areas, of household income, housing affordability, access to communication services, educational attainment, life expectancy and unemployment. We find no evidence of systematic negative associations between quality of life and the gross value of minerals production. Instead, mining activity has a positive impact on incomes, housing affordability and communication access across regional and remote Australia. Whilst we do not establish causality between mining activity and quality of life, our analysis prompts a rethink of the æresource curseÆ as it applies within a single country. Nevertheless, our findings are tempered by extensive anecdotal and empirical evidence of the negative social impacts of mining on specific demographic sectors, localities, families of fly-in, fly-out mining operations and individuals. This contrast may be a scale issue, with the regional benefits of mineral wealth masking highly-localised inequalities and disadvantage. We suggest that there is a need to better understand these impacts and, more importantly, the types of policy mechanisms government and industry can adopt to mitigate or avoid them.

Jan 1, 2009

By Paul Cameron Gilmour

Geologically, as distinct from economically, "porphyry copper (molybdenum, gold, silver, etc.) deposits" might be defined as large, disseminated and/or stock-work occurrences of copper-minerals, generally averaging less than 1 per cent cop-per. They are normally associated with small plutons which range in composition from granite to diorite, although, typically, they consist of quartz monzonite or granodiorite. Circumstantial evidence indicates that these "minor" granitic intrusions may represent the intrusive phases of post-orogenic, calc-alkaline volcanism, this conclusion being suggested by: 1. Texture and grain size. 2. Prevalence of intrusive breccias. 3. Relationship to unconformities and estimated depth of emplacement. 4. Spatial distribution in relation to orogenic zones. 5. Age of mineralization and igneous episodes

Jan 1, 1972

By Luis Pommier

The requirements of metals by modern society have created big challenges for mining engineers minerals processing engineers, metallurgical engineers and economists to produce these metals economically from mineral deposits which contain, with time, less and less value. The advances of science and technology allow, today, the exploitation of mineral deposits which only few years ago would not have been considered economical. However, there are limitations both on the minimum grade of recoverable values contained in the ore to be fed to a mill or on the concentrate to be smelted, and on the maximum content of "impurities" i.e. chemical elements which are difficult or expensive to refine from the ore, from the concentrate or from the metal. It is also known that the cost of treatment in a mill or in a smelter, for unit of metal contained in the ore or in the concentrate, increases as the grade of the recoverable values contained in them decreases and also if the content of impurities increases. In order to work a mineral deposit economically it is necessary to ensure not only that it has more than a minimum content of values, less than a maximum content of impurities and that there exists a good up-grading or metallurgical process but also to ensure that the opti-

Jan 1, 1971

By D. R. Lowe

Silicic volcanic ash and its alteration product, bentonite (montmorillonite and cristobalite), occur widely within sedimentary phosphate deposits. The genetic link, if any, between volcanism and phosphate deposition has yet to be satisfactorily established The phosphatic member of the Santa Margarita Formation (upper Miocene) in northwestern Ventura County, California, consists of approximately 15 per cent volcanic ash and bentonite. Ash and bentonite units greater than one foot thick can be subdivided into a lower zone of airfall origin and an upper zone of mixed ash and terrigenous detritus washed in from surrounding land areas. This upper zone also contains up to 20 percent phosphate pellets. These thick volcaniclastic units are typically overlain sharply by thin beds (less than 6 inches thick) of relatively pure, silica-cemented pelletal phosphorite. The shelf basin in which the phosphatic sediments accumulated was characterized by quiet, reducing but not euxenic bottom waters; Abundant decaying organic debris, mainly diatoms, served as a reservoir of readily available phosphate. The sudden influx of a large volume of silicic volcanic ash into this basin and its subsequent alteration to montmorillonite had two profound effects on thechemistry of the interstitial and bottom waters: (1) during alteration magnesium was removed from these waters and incorporated into the montmorillonite lattice, and (2) the pH of these waters increased as alteration progressed Both of these effects led to the crystallization in the bottom waters of carbonate fluorapatite. This accumulated as thin phosphorite beds immediately above the volcaniclastic units.

Jan 1, 1972

Relationships between lead blast furnace performance and the composition and size distribution of sinter were determined from analysis of lead blast furnace operating data. Sintering plant practice was subsequently modified and substantially improved furnace performance resulted.

Jan 1, 1971

Slake durability of rocks is an important property of rock-mass and rock-materials in geotechnical practice. The slake durability of rocks is closely related to their mechanical properties. In this paper, mechanical properties and slake durability tests for weak and clay-bearing rocks from Beypazari Trona Bed in Ankara, were performed in order to assess the slake durability and mechanical properties (especially rock strength) of these rocks as well as to understand the relationship between mechanical properties and slake durability. In performing this relationship, statistical based correlation has been applied.

Jan 1, 2003

By Vilem Petr

Optimization blast design parameters for rounds used at surface mines, quarries or cast blast has taken on a new importance with the increased the cost of the explosives and electronic detonators. This paper addresses the fundamentals of blast design and optimization explosive energy utilized for fragmentation. This laboratory studies shows that one key variable-the strain energy set up in rock mass by blast vibration – can be used to predict the extent of damage done to the rock strata, the degree of fragmentation of the broken rock, and the velocity of the broken rock. It also shows how the dynamic strength of the rock strata is influence the fragmentation size distribution as well as the blastability.

Jan 1, 2008