Search Documents

By R. F. Favreau

"After a blast, the volume of the blasted rock normally occupies more space that it did before the explosion. The degree of such swell significantly affects the efficiency of digging the muck with a shovel or dragline. This paper explains why swell occurs, and describes the new subroutine SWELL of the blast simulator BLASP A which can simulate blast-induced swell. Results are also presented which display the effect of various blasting parameters on the degree and distribution of the swell within the muck pile of a bench blast. IntroductionIt is a common opinion that fragmentation is the most important of the various aspects which affect the efficiency of excavating rock with explosives. This paper proposes that, in fact, displacement and swell of the blasted rock are as important as fragmentation if the excavation process is to be rapid and efficient. It must ""a priori"" be recognized that a minimum degree of fragmentation is indeed necessary. For a given shovel or dragline, this minimum degree of fragmentation may be defined as follows: even the largest fragment of rock must be easily contained within the bucket. Once this criterion is met, however, there are good reasons to believe that displacement and swell take over as the key criteria which influence the rate of mucking, in cubic metres/hour. If the muck pile is not well displaced and swelled, the teeth of the bucket have difficulty penetrating between the rock fragments even if fragmentation is good and, as a result, the mucking is slow and inefficient. The purpose of this paper is to use computer simulations on the model BLASP A to demonstrate the effect of the blast design parameters on the displacement and swell of the blasted rock."

Jan 1, 1993

By J. Olson

"A model was developed to use near-infrared (NIR) analysis of pulverized ore samples to estimate the recoverable gold content for ores from the Barrick Cortez Hills underground mine. Current routing practices use a ratio of the cyanide soluble gold content and fire assayed gold (CN/FA) to classify ores as oxide or refractory. Prediction accuracy of the NIR model was equivalent to the CN/FA ratio. Prediction accuracy was improved by combining the CN/FA ratio and the NIR spectra. Bootstrap validation estimates the root-mean-square error to be 9.92% with an estimated r-squared value of 0.893. This model will allow more accurate estimates of the variability in recoverable gold content throughout this mine. These data will aid in building an improved geo-metallurgical model or in making better informed routing decisions during the production cycle.INTRODUCTION The contained gold of an ore available for cyanidation is often related to subtle variations in the mineralogy. It is difficult and expensive to collect enough mineralogical information in order to predict how the variable mineralogy will impact the metallurgical results and project economics throughout the life of the mine or mill. Near-infrared spectroscopy may be an effective tool to rapidly and inexpensively collect discrete, quantitative mineralogical data for minerals that contain transition metal oxides, metal sulfides with semi-conduction properties, rare earth metals, and some chemical groups having di-pole covalent bonds such as carbonates, sulfates, and various types of clays (Hunt, 1977). Near-infrared spectroscopy can be a powerful tool for geo-metallurgical characterization of deposits where the presence of these minerals has direct or indirect relationships to metallurgical results such as grindability, regent consumption, or recovery. Near infrared spectroscopy is a rapid analysis that measures the intensity of reflected light in the near-infrared spectrum. The ranges for the ASD-Panalytical units used in this study extend through the visible spectrum and into part of the UV spectrum, reporting reflection by wavelength from between 350 nm to 2500 nm. Absorption peaks visible in this range are a result of interactions with outer valence elections or chemical bonds. The location and intensity of the peaks vary depending on the chemical composition and crystal structure of a solid indicating the presence and abundance certain minerals (Hunt, 1977; Clark, 1984)."

Jan 1, 2017

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

By Susanna G. de Jager, Francis W. Petersen

"The aim of the project was to develop a methodology applicable to different South African coal types to be able to predict with a high degree of certainty what kind of reagent will be suitable for flotation of a certain coal type.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements.The flotation tests showed that the best reagents to float all of the coal samples studied are iso-decanol and dodecene. These reagents produced flotation products that are near to the release curve. Statistical relationship for predicting ash content and yield that can be expected for a certain coal type and selected collector was obtained. From the relationship, the accuracy of the yield is above 95% (p-value below 0.05) with a linear regression of 0.9289. The accuracy of the ash is slightly lower with a linear regression of 0.7841 but also above 95%."

Jan 1, 2003

By Susanna G. de Jager, Francis W. Petersen

"To enable the prediction of reagents suitable for fine coal flotation, it is necessary to develop a methodology applicable to different South African coal types. Statistical confirmation of the applicability of this methodology is important to avoid recommendation of reagents on a trial and error basis.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements. Flotation tests were used to validate expectations from the characterisation of the coal samples.RESULTSThe flotation data indicated that all of the coal samples were amendable to froth flotation. The best results were obtained with the Witbank seam 2 coal and the poorest flotation with Syferfontein seam 5 coal. The flotation tests showed that the best reagents to float all of the coal samples studied were iso-decanol and dodecene. These reagents produced flotation products that were near to the release curve, which are the optimum flotation results (obtained when using iso-paraffin as collector). Dodecene resulted in low ash products and iso-decanol in high yield products."

Jan 1, 2003

By Terry Nichols, Karl E: Warkwick Burgher, Charles J. Wideman

The application of Fourier spectral analysis to records of ground vibration generated by over 100 explosions from an open pit mine is used to develop empirical predictor equations that relate the response spectra to the blasting parameters used to generate the excitation motion. Time series representations of ground particle velocity are transformed into the frequency domain where the appropriate modifications are made such that the inverse Fourier transform yields the time series representation of particle displacement and acceleration. Compensations are made for the transform function of the recording system in the frequency domain. Spectral analysis of the three types of ground motion is correlated with the blasting parameters. The results show that the frequency content of ground vibrations generated from a mine blast can be quantified in terms of the predictor equations.

Jan 1, 1990

By Michael Karmis

This paper reviews the fundamental concepts involved in the development, application and validation of ground movement predic¬tion methods developed by Virginia Polytechnic Institute and State University (VPI&SU) over the past 12 years. Prediction techniques have included empirical or semi-empirical methods, such as the profile function, influence function and zone area methods, as well as numerical methods, based on a finite element formulation which utilizes field subsidence data. The former techniques have been integrated in the Surface Deformation Prediction System (SDPS) software package for personal computers, which allows for the calculation of any component of ground movement in any direction. Comparisons between measured and predicted subsidence and strain values are presented for a selection of case studies, which demonstrate the applicability, accuracy and regional validity of these methods for predicting surface deformations due to underground mining.

Jan 1, 1986

By K. L. Morton, R. .. J. Connelly, P. C. Bouw

Uncertainties in the forecasting of the volume of groundwater likely to enter underground workings present difficulties for mine management in planning and costing the water-related activities of mining. This paper describes a technique that was developed to assess future inflows into a gold mine in the Orange Free State. The approach employed was based on the interactive operation of two separate computer models: a regional-flow model and an inflow model. As a first stage, a regional finite-element model of groundwater flow was set up and calibrated. Predictive runs were made to establish the influence of mining on the water levels from base-line conditions. This step was necessary since observations of the regional water levels were sparse. The predicted water levels were transferred to the inflow model, and the future flowrates were calculated. Both models were calibrated by trial and error until a satisfactory match was obtained between historical records and the values predicted by modeling. In this way, an improved monitoring system to record regional water levels and pressure heads within a mine was established. By the use of information, the initial model predictions can be refined as mining progresses. The models used are based on a non-linear relationship between the area mined and the inflows. A phased behaviour in the rates of inflow increase was noted. In conclusion, the modeling approach can provide mine management with guidelines for dewatering requirements. The confidence levels depend upon the records that have been collected during the mine's history.

Jan 1, 1988

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By J. Andersen

The very large quantities of energy used for size reduction in the minerals processing industry necessitate the accurate prediction of comminution machine power draw for optimum plant design. The JKMRC has developed effective models for predicting ball mill, autogenous mill, semi- autogenous mill and crusher power draw. When combined with comminution models they provide a powerful tool for evaluating not only the size reduction performance of a plant design, but its power utilization efficiency as well. This paper describes the structure of the mill and crusher power models. Data from a wide range of equipment types are presented which illustrate the accuracy of these models.

Jan 1, 1992

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

By Shuai Wang, Gang-hua Fu, Lu Yang, Yu-feng Guo, Tao Jiang

The fluorine-bearing iron concentrate is one of the refractory raw materials for pelletization, which is mainly used in Baotou iron and steel company with lots of problems, such as narrow roasting temperature range and low compressive strength of products. According to its specific character, the effects of roasting temperature, time on the compressive strength and microstructure of pellets were researched. The results show that low melting substances formed during the roasting was the dominant reason of those problems. High melting substances were added in the roasting to investigate their effects on the roasting properties of fluorine-bearing iron concentrate pellets. Low melting substances were reduced when chromite was added. The compressive strength of products was 3100N/P when the 2% chromite was added at the roasting temperature of 1150 ºC, which was increased 700 N/P compared with the pellets without chromite, and the roasting temperature range was expanded by 170 ºC.

Jan 1, 2016

THE record of the development of physical metallurgy since the founding of this Institute embraces by far the greater part of physical metallurgy as this subject is recognized today. Yet it is not to be supposed that the metallurgist interested in the properties and behavior of solid metals at the beginning of this period was without important and even fundamental information. He had an empirical knowledge of the behavior of solid metals which extended backward into prehistoric times and he had the early beginnings of many of the chapters in the science of metals. Industry was burgeoning in many directions, for methods had been developed, especially in the manufacture of steel that provided materials in extremely large tonnages, permitting applications of metallic materials on a very widespread scale. These multitudinous new uses of metals created an increased interest in the behavior of metals, and provided the basis for the rapid development of a science of metals. Indeed, the development of science generally that accompanied the industrial revolution reached a flood tide toward the end of the century, furnishing the metallurgist basic principles in chemistry, physics, mechanics, and crystallography that would shortly be extensively applied to metallic behavior. In this account, the early developments in the wide metallurgical field will be traced, in order that the status of physical metallurgy in 1871, when this Institute was founded, may be clearly seen. The subject of metallurgy in antiquity has been written upon frequently and at length. We shall here no more than indicate the main features that we need to define the position in 1871 and to provide a proper background for discussing subsequent developments. The writings of Pliny,1 23-79 A.D., to which Robex-ts-Austen3 fre-

Jan 1, 1948

By C. Tong, B. Hilscher

"Sensor based ore sorting is being rapidly adopted by the mining industry. The ability to boost mill feed grade by rejecting waste grade rocks early in the process has proven revolutionary for some operations.This paper briefly reviews the current position of ore sorting in the industry, as well as abridged results from specific operations such as Barrick, McEwen, New Gold, and two others. The paper also introduces the concept of “Profit Recovery™”, the measuring of recovery based on rock profitability rather than just metal content.IntroductionSensor based ore sorting is being rapidly adopted by the mining industry. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes have been too invaluable to be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. In addition, the advent of ore sorting has also called for a new standard of recovery analysis. The answer to this is the creation of a new term and concept - Profit Recovery™.This paper evaluates the most recent results of ore sorting in the mining industry, and presents the results from five different mining operations. Additionally, this paper will discuss and evaluate the Profit Recovery™ of each of these operations. The goal of this paper is to address common concerns regarding ore sorting rejects and their actual impact on project economics.State Of The ArtOre Sorting is a sensor-based sorting and pre-concentration technology implemented before the processing stage that is used to reduce the amount of waste reporting to the mill feed. This technology can also be utilized to recover ore from previously uneconomic waste, as well as reduce the mill energy and reagent consumption (Tong, 2012). In greenfield projects, sensor-based sorting can further provide value by reducing processing capital costs. The decline of available high grade orebodies and decreasing head grades has further increased the attractiveness of pre-concentration, and subsequently ore sorting (Lessard et al., 2014).There are currently two notable types of sensor-based sorting: bulk and rock-by-rock. Bulk sorting consists of live, high tonnage sorting that can be installed on a scoop or on a conveyor belt with a diverter. Rock-by-rock is a selective sorting method that scans and sorts individual rocks on a conveyor belt, and rejects rocks using air jets or mechanical levers. Figure 1 shows a diagram for a typical air jet sorter."

Jan 1, 2018

By Phil Keele

Canadian Natural ??Business Approach Efficiency and Execution ?Drive to be the low cost producer ?Focus on exploitation ?Augment exploitation with strategic acquisitions ?Maintain Discipline and Strength while Delivering on the Defined Plan ?Maintain flexibility and control allocation of capital ?Strive for balance (asset portfolio) ?Maintain financial strength

May 1, 2010

By Takayuki Watanabe, Yoshiki Shimizu, Yusuke Moriyoshi

"B-C-N nanotubes prepared by a flush evaporation method using a de arc plasma were mainly characterized by transmission electron microscopy (TEM) and electron energy· loss spectroscopy (EELS). The nanotubes obtained· were divided into three types such as carbon boron nitride and carbon or carbon nanotubes surrounded with boron nitride nanotubes. These types of nanotubes were obtained at higher temperatures than about 3000 K, however, these were not formed at lower temperatures than about 3000K. On the other hand, 11anocapsules were· formed at all the experimental temperatures and nanocapsules with a homogeneous phase were obtained at lower temperatures than about 3000 K. The effect of additives on the formation of B-C-N nanotubes was not clear. Based on these experimental data depending on temperatures and corresponding microstructures, the formation mechanisms of both nanotubes and nanocapsules were briefly .discussed 1 Introduction As reported previously, nano tubes have unique electrical properties1, 3) The preparations of nallotupes have been usually carried out by flush evaporation methods using either a de arc plasma or a laser4 -5) By these methods the reaction rate is so rarid that we have no data of intermediate products between initial raw materials and. final products of nanotubes 6-9). So, the formation mechanisms of nanotubes have been mainly speculated only from the microstructures of resultant nanoiubes. In order to have more reliable formation mechanisms, it is particularly important to have the information of intermediate products at the corresponding temperatures. From the viewpoints, we have studied about the effects of temperatures on the preparation of nanolubes. Here we report mi firstly some problems on the preparation of B-C-N nanotubes 10), secondly the effects of temperatures on the preparation of B-C-N nanotubes, and finally the formation mechanisms of nanotubes."

Jan 1, 2000

Following the preparation of tantalum oxide and carbide (1) an investigation of the details relating to the production of tantalum metal powder was planned. From the literature (2) it was evident that tantalum could be produced either by reduction of potassium tantalum fluoride with an alkali metal or by electrolysis of a fused salt mixture containing a tantalum compound. The latter method appeared to be the more suitable and, as there was considerable divergence of opinion in the literature as to the nature of the reactions involved, it was decided to study the electrolytic process. The ultimate aim in any case was to produce tantalum pOWder for use in an investigation of the problems relating to the preparation of consolidated tantalum.FACTORS GOVERNING ELECTROLYSISAfter a few preliminary exploratory electrolyses several factors which needed amplification were revealed. These will be mentioned before the details of the electrolysis experiments are given.COMPOSITION OF THE BATHWithout the knowledge gained in the preliminary experiments it would be thought that the best material for the bath would be that one which underwent electrolytic decomposition. Consider what at first appeared the most likely - namely - potassium tantalum fluoride. The melting point of K2TaF7 was determined to be 630°C with volatilization and decomposition taking place at that temperature so that it would not have been very satisfactory.

Jan 1, 1946

Much interesting data on cemented carbides has been published over a period of years which, when classified and pieced together, gives a clear picture of this special branch of powder metallurgy. This is an attempt to present the essential information in an ordered account.THE HARD CARBIDES-THEIR PROPERTIES AND PREPARATIONThe so-called hard or refractory carbides are the carbides of a number of metals which are grouped together in the Periodic Classification. These metals are in groups IV, V and VI. They are titanium, vanadium, chromium, zirconium, niobium (columbium), molybdenum, hafnium, tantalum and tungsten. These carbides have attracted the attention of chemists because of their remarkable properties. They possess very high melting points, and are rather difficult to prepare in the pure state. Their outstanding propertyis their extreme hardness, which they share with certain other carbides, such as those of silicon and boron. In addition, these compounds possess distinctly metallic properties, such as lustre (in fused specimens) and high thermal conductivities.(l)t They are capable of forming alloys in two ways:1. With metals, particularly those of the iron group. 2. With each other (a case of solid solubility).The constitution of these substances is not that of ordinary salts, which obey the usual valency rules, but must be likened to that of certain intermetallic compounds. Actually they are "interstitial" compounds(2), that is, they are formed from the ordinary metallic lattice by the insertion of the relatively small carbon atoms in the interstices.. The energy required to fill the lattice completely is high, and this explains the difficulty often found in obtaining the exact stoicheiometric compound. Thus the carbides can have a range of composition, and can be considered as solutions of carbon in the respective metals.Physical Properties of the CarbidesThe hardness of these compounds is so great that it is difficult to compare the individual compounds on this basis. Becker(l) gives values on Moh's scale, which are not very accurate and are of no great value. Burden(3) has reproduced a diagram by Hatfield which indicates that the cemented carbides are between 1,400 and 2,000 on the Vickers diamond scale. However, the pure carbides are harder, tungsten carbide being about 2,200. Hoyt(4) describes a method of measuring hardness applicable to powdered specimenswhereby the powder is rubbed on a standard block of cemented tungsten carbide under standard conditions, and the rate of wear is determined. In...

Jan 1, 1942

By Q. P. Campbell

Activated carbons used in the precious metals extraction industry are characterized by large internal surface areas and a great affinity for metal ions. The purpose of this research is to prepare activated carbon from a South African bituminous coal by physical activation that is suitable and cost-effective for use in the extraction of metals. The quality of the coal-based activated carbon may not prove to be as good as activated carbon produced from other traditional sources, but the production costs involved may make South African coal a feasible alternative feedstock. The activated carbons produced were characterized by Brunauer, Emmett, and Teller (BET) surface area, activated carbon pH, and phenol adsorption studies and the results compared to the results from a commercially available activated carbon, Norit RO 0.8 (control sample). Bituminous coals from various sources including Witbank Seam 4 and Free State coal were used in this study. The preparation method chosen was physical activation using superheated steam. The effects of process variables such as activation time (1-3 h) and temperature (600-800°C) were studied in order to optimize those parameters. The activated carbon surface area was characterized by means of nitrogen adsorption isotherms at 77K. BET surface area analysis showed that Witbank Seam 4 coal activated at a temperature of 800°C and activation time of 3 hours resulted in a surface area of 340 m2/g. Quality control of each sample was performed by measuring the pH of a known amount of the prepared activated carbon in distilled water over time. Results showed that the pH of some of the prepared activated carbons reached a value of 11. Phenol adsorption results for the different activated carbons prepared corresponded well to the results obtained for the Norit RO 0.8 activated carbon sample.

Jan 1, 2012

By Paul Sterling

1. INTRODUCTION. THE general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a "coal-breaker." This name is misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only in the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for domestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Oct 1, 1911