Search Documents

From the viewpoint of mechanical efficiency, charges should be fully coupled and, upon detonation, should just fail to break the rock in compression. But because mining thrives on its cost-effectiveness rather than its mechan- ical efficiency, the explosive which generates maximum energy per $ should generally be used, even though the mechanical efficiency of this explosive's detonation products may be sub- optimum. Wherever possible, each charge should have a length:diameter ratio of about 20 or more and should shoot to a concavely biplanar free face that is both parallel and reasonably close to the blasthole. Success in obtaining parallel effective faces often demands the drilling of angled blastholes and, hence, will require intensified research and development efforts by drilling manufacturers, especially where hard strong rocks are encountered. Blastholes should be drilled on equilateral triangular grids and fired in a Vl or shallower V-type sequence using inter-row delays which ensure that good pro- gressive relief of burden is achieved. The conventional method of calculating Se/Be values (on the basis of planar effective faces) is often invalid.

Jan 1, 1986

During the extensive research which has been conducted in the Metallurgy Department of the University of Melbourne, into the properties of lead and its dilute alloys, the Brinell test has been used for the determination of hardness.The work described herein represents part of an investigation into the influence of various factors on such determinations, particularly when carried out on different qualities of "pure" lead. It is intended to publish the more theoretical and controversial aspects of this research elsewhere.MATERIALS USED AND THEIR PREPARATION FOR TESTINGThe tests to be reported have been conducted on a specially pure electrolytic lead, and several brands of commercially "pure" lead. The analyses of the samples upon which most of the work has been carried out are given in Table 1.Note: Oxygen was not determined, but from the work of H. W. Worner, in the Rosenhain Memorial Laboratory, it appears probable that it was approximately 0-0003% in all samples.

Jan 1, 1940

By Roger Altman

The solubility of copper in primary spinel crystals encountered in reverberatory slag samples has been determined by electron microprobe analysis. These spinels, which ranged in composition from 22% A12O3 to pure magnetite, contained small quantities of dissolved copper (0-0.4%). Based on literature data it was estimated that the solubility limit of copper in solid magnetite is no greater than about 1% at 1200°C and about 2% at 1250°C. However, it was found that practically every spinel crystal examined contained significant amounts of matte inclusions. Further examination of converter slag revealed large quantities of irregularly shaped precipitated magnetite crystals which contained a large proportion of copper inclusions. Additional experimentation showed that the total copper content in reverberatory slag samples was greater than the sum of the estimated en- trained plus dissolved matte in the slag. This difference is believed to be significant and is due to the presence of matte inclusions in the spinel crystals. In the present reverberatory slag samples these inclusions accounted for about 1/2 of the amount of sulfide directly entrained in the slag.

Jan 1, 1976

The corrosion behaviour of a low carbon steel was investigated in synthetic seawaters with and without Sr2+. It was found that strontium substitutes for calcium in aragonite, rather than precipitating as discrete strontianite (SrCO3). The aragonite deposits that formed in the presence of Sr2+ were finer than those that formed in the absence of Sr2+. It is believed that an increase in the strontium content of aragonite induces a decrease in its solubility, which in turn results in a higher nucleation rate of the precipitates. Furthermore, the growth rate of aragonite is decreased by the presence of Sr2+in the solution. It is concluded that Sr2+is an essential ingredient in any artificial seawater when calcareous deposits are investigated on steel. Keywords: corrosion, seawater, calcareous deposits, strontium, aragonite.

Jan 1, 2007

By M. Mpofu, B. Maphalala, S. Khan, S. Ngobese, D. Roberts

This paper details an assessment of stemming practices at a South African opencast coal mine and their influence on ground vibration and air blast. Quantitative and qualitative analysis methods were used for the study. The parameters assessed for the quantitative analyses included stemming length, stemming material type, blast-hole depth, burden, and spacing. Pre-blast data from the mine was analysed to determine the deviation between actual and mine design stemming parameters. Mine design stemming length was also compared to the rule-of-thumb stemming lengths. Peak particle velocity (ground vibration) and air blast data from seismograph stations around the mine was analysed to determine the correlation between stemming length and excessive ground vibration and air blast. The qualitative analysis involved observations of blasting procedures at the mine to determine compliance with mine procedures. Some level of non-compliance of actual stemming parameters to design stemming parameters was found, which initially suggested that non-compliance may have contributed to excessive air blast. However, further analysis of the seismograph results indicated no direct correlation between stemming length and excessive air blast and ground vibration. Since stemming parameters are interrelated, it is crucial that all blasting procedures, including stemming, are executed in accordance with best practice, and recorded accurately. There is a need for digital systems for capturing on-bench blasting parameters, as the currently used manual data recording and reporting systems are inefficient and prone to error. Improvements to blast designs are possible through efficient and accurate data recording and reporting systems.

Jan 1, 2021

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

By John L. Hill

Over 50 mines of the Appalachian and Illinois Basins are presently experiencing poor ground conditions believed to be caused by overlying stream valleys. The Bureau of Mines is conducting research into the causes of this problem with the aim of developing a predictive method for determining the safe limits of mining beneath stream valleys. In addition, the factors that control instability in these regions will be analyzed to provide design guidelines for adjusting support requirements. This paper presents the theorized causes of poor ground conditions beneath stream valleys and compares the theories with the results of a Bureau study of the Birchfield Mine No. 1 and a preliminary investigation of the Davidson Mine, both of southern West Virginia. The Birchfield Mine excavated four main entries beneath a 50-ft wide stream with only 50 ft of overburden. The valley flood plain is over 500 ft wide, flanked by valley wall slopes of 25 deg and relief of over 950 ft. In-mine monitoring of strata movement and detailed geologic mapping revealed that roof rock strength was greatest under high cover and weakest along outcrops and beneath the valley, with localized areas of decreases in rock mass quality. To improve the rock mass quality beneath the stream and reduce the threat of inundation, an extensive drilling program was undertaken to inject grout into the overburden from the surface. As a result, mining beneath the stream was practically routine from a ground control perspective, and water was not encountered until mining had advanced to a point beneath the floodplain that had not been grouted. The only ground control problems which were encountered were entirely a result of localized poor rock mass quality. In contrast to the Birchfield Mine, the Davidson Mine experienced failure of intact roof rock at a depth of 300 ft beneath a V-notch shaped valley with no change in rock mass quality. Finite element analysis was conducted to study the premining in situ stress at the two sites. The results are discussed within this paper and provide insight into the causes for the types of failure seen beneath valleys of varying shapes and depths.

Jan 1, 1988

By Charles W. Schwartz, Subash Kolluru

INTRODUCTION Creep of rock in situ, like most rock mass behavior, will be largely governed by the behavior of the natural discontinuities -- bedding planes, faults, and joints, in particular, Several past studies have investigated various aspects of the time-dependent deformation of rock discontinuities; examples include Amadei and Curran (1980), Engelder and Scholz (1976), Johnson (1975), Kaiser and Morgenstern (1979), Solberg et al. (1978), and Wawersik (1974). These studies have provided much insight into the general phenomenon, but they have also produced some inconsistent conclusions and left many unanswered questions. This paper will attempt to shed some light on one of these questions: What is the influence of stress level on the creep of unfilled rock joints? The discussion will follow a two-part approach to the problem: (1) laboratory creep experiments on small scale jointed specimens, (2) a simple theoretical mechanism to explain, at least in qualitative terms, some of the results from the experimental program. EXPERIMENTAL PROGRAM Uniaxial creep tests were conducted on intact and jointed samples of a specially formulated gypsum plaster "synthetic rock." Synthetic rock materials have several advantages over natural rock for long-term creep testing: (a) higher creep rates, (b) lower strength and therefore lower loading requirements, (c) simpler specimen preparation, and (d) more controlled and consistent properties. Gypsum based plasters have been used previously in studies of short-term strength and deformability of jointed samples (Patton, 1966; Einstein and Hirschfeld, 1973). Furthermore, Williams and Elizzi (1977) demonstrated that natural gypsum, at least, creeps in a manner similar to that of most other creep-susceptible natural rocks.

Jan 1, 1982

By G. Peinaar

Superhardening is a new development by which a substantial increase in hardenability above the normal can be achieved in Iow-alloy steels. This paper concerns the reversible temper-embrittlement behaviour of steels with a superhardenability characteristic. Steels of type BS 530A40 with manganese modifications varying from 0,72 to 1,27 per cent in the superhardenable and conventional condition were compared. It was concluded that superhardenability in itself does not affect the susceptibility of a particular steel to temper embrittlement. However, an increase in manganese content, which was intended to increase the base hardenability of the steel, caused serious deterioration of the temper-embrittlement properties. As the use of manganese, chromium, and nickel to increase base hardenability results in an increase in susceptibility to temper embrittlement, it is suggested that this effect should be countered by the addition of 0,2 to 0,3 per cent molybdenum.

Jan 1, 1984

By B Indraratna, A Dey

The surface geometry of a rock bolt plays a very important role in the rock/resin/bolt load transfer mechanism. Very little work has so far been reported on the influence of the bolt surface geometry on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness condition in the laboratory. To study the shear behaviour of the bolt/resin interface a series of shear tests with an initial normal stress between 0.1 to 7.5 MPa has been conducted on the flattened bolt surface of two most popular bolt types currently being used in Australia. Bolts with deeper ribs offered better shear resistance at low initial normal stress conditions whereas bolts with shallow and closer ribs offered better shear resistance at high normal stress conditions. The maximum dilation occurred at a shear displacement of 60 per cent of the rib spacing irrespective of the bolt type and depth of the rib.

Jan 1, 2000

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By K. Lillkung

The use of secondary sources has become a very attractive option in the production of platinum group metals as the demand for these metals has increased. One of the promising sources are the spent catalysts, which provide an attractive source as they have relatively high metal content compared with the ores where the metal is originally extracted from. The concentration of platinum group metals in catalytic converters is in the range of 0.1-1 mg/g as the concentration in ores is usually less than 10 ppm. Aqueous chloride solutions are claimed to be a cost effective way in which platinum group metals can be brought into solution and concentrated. In this work the effect of different parameters on the dissolution rates of Pt, Pd and Rh were investigated. The parameters investigated were the Cl- concentration, the temperature and applied potential. Chloride concentrations used were 62.5, 90, 125 and 250 g/l. Temperatures were 25, 40, 60, 80 and 94°C. Potentials were 950, 1050, 1150 and 1250 mV vs. SCE for Pt and Rh and 380, 410, 440 and 470 mV vs. SCE for Pd. Dissolution rates were calculated from the current densities determined by potentiostatic measurements. Thin wire electrodes were used in the measurements. As expected, higher temperature, higher potential and higher chloride content generally increasedthe dissolution rate. However, the effect was nonlinear and slightly different for different metals. The results show that strongly oxidizing conditions are needed in order to achieve reasonable dissolution rates. With the highest chloride content and at potential of 1250 mV vs. SCE and 94°C the dissolution rate of Pt was nearly 1 mm/h, whereas in similar conditions Rh achieved a rate of only nearly 100 µm/h. Similarly, with the highest chloride content and at potential of 470 mV vs. SCE at 94 °C the dissolution rate of Pd was nearly 1 mm/h. Keywords: Pt, Pd, Rh, redox potential

Sep 1, 2012

By J. K. Jeyapalan, A. P. S. Selvadurai

Plate loading tests which use surficial loading of a rock mass are employed quite extensively for the determination of in situ deformability characteristics of rock masses. The cable jacking method is essentially a surficial plate load test in which the test load is provided by reaction against a cable anchored at some depth below the rock surface. The results of the test are usually evaluated within the framework of the classical theory of elasticity to generate estimates for the bulk deformability properties of the rock mass. In the conventional evaluation of this test it is assumed that the test plate is rigid and that the embedded anchor load has no influence on the test plate settlement. The purpose of this paper is to examine the possible influences of the plate flexibility and the anchor load location on the effective settlement of the test plate. The variational estimates presented in the paper are valid for moderately flexible test plates which are characterized by a relative rigidity parameter Numerical results are developed in the form of correction factors that should be applied to the cable jacking results to arrive at the deformability characteristics of the tested rock mass.

Jan 1, 1982

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By Angus D. Campbell

"IntroductionThe subject assigned to me tonight gives unlimited scope. The material available is so voluminous and leads into so many ramifications, and the memories of the Camp are so vivid and treasured, that it is difficult to decide just what to use. Then, too, the geologists are the story-tellers of our tribe - I am only a hard rock miner.Members of the Cobalt Branch and Cobalters everywhere will agree without question that this Cobalt camp has been the greatest of all influences on Canadian mining. To those who do not know Cobalt, our opinion may seem prejudiced and our statement exaggerated.Be that as it may, discussion on this subject can be profitable, since it is worthwhile now and then to think on 'whence we came' and 'where we are going'.In the revival of interest in the Cobalt camp, we hope our guests may feel some of the old Cobalt Spirit, which has become the Spirit of the North.Visitors may even, while here, catch a glimpse of that whimsical little guardian spirit of the camp - the original goblin, the Kobold - for which Cobalt was named.While Kobold brings that good luck which plays so important a part in mining, he can have his evil moments, as in his original German home. There, when he made the silver disappear from their good ore, they cursed the grey ore, calling it Kobold.Although this little goblin bas frequently upset our best mining plans and geological calculations, be has played the game as well. He placed •some silver on the surface, and when he hid ~t at depth he left dues .for its finding. He has rewarded many who sought his treasure and is still rewarding those who have persevered and had faith in him. t:lis influence and that of Cobalt camp has probably had a greater influence on your work and your mining areas than you realize"

Jan 1, 1950

By E Kasai, T Nakamura, E Shibata

In the present study, formation of PCDD/Fs from carbon particles like æsootÆ, so called de novo synthesis, was experimentally simulated using the powder mixture of graphite and metallic chloride. Composite states of graphite and chloride particles were varied by the preliminary treatment, ie high-energy ball milling for different time or heating at different temperatures. These samples were subjected to the measurement of the rates of weight loss mainly due to the oxidation of carbon, the formation of absorbent organic chlorides (AOX) and the formation of PCDD/Fs at 300¦C. The amount of PCDD/Fs formation increased by applying certain pretreatments. Further, linear relationships were obtained among the formation rates of PCDD/Fs and AOX and the weight loss of sample. These results will give useful information to investigate the mechanism of PCDD/Fs formation from unburned combustible carbon and hydrocarbon in thermal processes.

Jan 1, 2002