Search Documents

By N. E. Norman

The big hole drilling industry is a relatively new one. In fact, very little big hole drilling was done prior to 1950. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry. Let us examine the three main features of big hole drilling and determine how each applies to mining. Let's also look at the good qualities and the limitations of each of these character traits.

Jan 1, 1968

By Adrian Brown

INTRODUCTION The primary tool which is available to improve the stability of an open pit mine at a given slope angle is control of groundwater pressure. This paper sets out the methods by which water pressure control can be achieved in large mines in different materials. The emphasis of this paper is on large mine slopes because. these slopes exhibit the greatest need for groundwater control, the greatest economic benefit from groundwater control, and the greatest technical challenge in achieving groundwater control. STABILIZATION USING MTER PRESSURE CONTROL Groundwater pressures reduce the stability of slopes in two fundamental ways, as shown schematically in Figure 1. In the example, a horizontal failure surface intersects a vertical joint or weak zone. Water pressure acts: o On the base plane to reduce the normal force on the sliding surface and hence reduce frictional resistance to sliding, and o On the vertical back plane, to create a driving force for the system.

Jan 1, 1983

By Peter N. Calder, Alan Bauer

INTRODUCTION One of the most important decisions involved in the design of an open pit mine is the selection of a slope angle. Despite this fact, engineering procedures have developed slowly in this field. Only recently have the instruments and know-how become available to undertake a design based on sound engineering principles. The effect of blasting on open pit slope stability is one aspect in which the state of the art has not developed fully. These effects include: a) the effects of the ground motion associated with blast waves on slope stability, and b) the fracturing of rock in the vicinity of slopes caused by blast waves. Natural rock jointing plays an important role in both of these. SUMMARY OF BLASTING EFFECTS In recent years there has been a trend to larger sizes of blast holes in open pits to the extent that today 9% in. and 12% in. diam. holes are the most common. The reasons for this have been economic. Larger machines are more efficient and produce at a lower overall cost per ton. As the size of blast holes have increased, so have the other factors associated with blasting. Bench heights have increased, the tons/ft. of hole yield has risen significantly and the explosive load per hole has increased. Quite naturally the rupture radius for a single blast hole has increased along with the vibration level produced per blast hole. Open pit blasting operations can result in two types of unwanted damage: 1. Damage to structures, such as buildings, dams and slopes by ground vibrations initiated by the blast. 2. Fracturing of ground beyond the planned excavation limits. Let us first consider item one. Vibration effects are determined by the type of blast which is fired and the type of medium through which the blast wave is being transmitted. They are strongly influenced by the weight of charge per hole, the number of holes per delay, the distance from the shot point, the mode of initiation, the point of interest relative to the blast, etc.

Jan 1, 1971

By Jacob Carr, Christopher C. Jobes, Chenming Zhou, LaTasha R. Swanson, Jennica Bellanca, Jingcheng Li

Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM— the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered.

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By A. N. Brown

This title of is not that originally chosen for the Colloquium, which was 'A high gold price'. Such a title would have been unfortunate because it would have related the Colloquium only to the high gold price of the past two years, which reached the dizzy peak of 850 dollars per ounce in January 1980. The chosen title is, of course, the right one because it places the whole problem in the right perspective. It relates to a situation that has occurred many times before. Over the course of the past century, the gold price has periodically been inhibited from rising, so that it has undergone a succession of stepwise increments. With each increase, the relationship of the working cost to the gold price alters, and gives rise to a jump in ore reserves. Award for CMI fuelling technique Consolidated Metallurgical Industries Limited - the Lydenburg-based ferrochromium producer in the J.C.I. group - was one of the five recipients of the 1981 National Productivity Institute annual award.

Jan 1, 1981

By G Senanayake, J Andreazza

The general experience in gold cyanidation research activities and plant practice is that high oxygen and cyanide concentrations improve gold leaching kinetics which in turn reduce residence time and increase throughput. This paper shows how the improved pre-oxidation method for the pyrrhotite rich gold ore of Bounty Gold Mine has increased gold recoveries at lower reagent consumption rates. The installation of a pipe reactor, in conjunction with a Multi Mix Systems oxygen injector, has lowered the amount of oxygen required to achieve a dissolved oxygen level target of 20 mg/L. The improvement of the pre-oxidation stage and lead nitrate solution addition has led to a reduction in the free cyanide concentration required for leaching, resulting in a decrease in cyanide consumption rate by 36 per cent to achieve a one to two per cent improvement in the gold recovery.

Jan 1, 2002

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place. There are two possible mechanisms describing this process:(a) Gas nucleation, caused by nano bubbles inside the film.(b) Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals).Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film."

Jan 1, 2003

Resource rent tax is a form of taxation or royalty, which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax (APT). The implications of the current form of Additional Profits Tax for shareholder cash returns are that the tax burden on the operation may suddenly increase at some stage in the life of the mine, if and when the threshold level of profitability for the tax to be triggered is exceeded. From that point in time onwards the cash return to the shareholders on the capital invested is greatly diminished. For mining companies in Papua New Guinea, the effective tax rate increases from 35% to 57.75% as a result of the onset of Additional Profits Tax. This tax rate penalty is so severe that there appears to be merit in considering the concept of managing profitability through time rather than purely maximising annual pre-tax profits as is currently the case in most mining operations. This would have the benefit of deferring or perhaps preventing altogether the onset of the tax. One possible method for the effective management of profitability is through the control of average mining grade by cutoff grade manipulation. Traditional cutoff grade theory has usually considered taxation as a direct cost at a fixed or variable percentage of annual profits. As a result of this most analyses are conducted on a pre-tax basis. If tax is included in analyses it is usually present as a time independent function of gross profit. Additional Profits Tax is both time and rate of return dependent and therefore not adequately accommodated by currently accepted cutoff grade theory. A review has been made of the effects of resource rent taxes on both the investment decision-making process as well as possible development and mining strategies which may be employed by mining companies faced with Additional Profits Tax. The review includes examples based on the structure of Additional Profits Tax which is levied in Papua New Guinea.

Jan 1, 1997

By H. B. Arntzen, P. O. Grøntvedt, T. Lindstad, R. J. Ishak, M. Syvertsen

Better utilisation of electric power and coke is vital in reducing production costs and CO2-emissions in production of ferromanganese. All FeMn smelting operations consume 10 to 30 % more carbon than the carbon needed to reduce MnO and FeO to metal and the carbon contained in the alloy. Potassium which re-circulates and builds up in the furnace has been shown to be the main culprit causing both excessive carbon consumption, by catalysing the Boudouard reaction, and increased electric power consumption. The reaction between CO2 and ordinary metallurgical coke or coke impregnated with potassium has been studied at temperatures from 800 to 1100°C in a thermobalance apparatus. Ordinary coke did not react to any great extent at temperatures up to 1000°C, whereas the addition of potassium (2-10 %) resulted in a huge increase in reaction rates. The ultimate goal is to fit the results into a reaction rate model containing the equilibrium constant for the solid-gas heterogeneous reaction between CO2 and a free active site on the carbon reactant producing CO and adsorbed oxygen (an occupied site). The model includes the partial pressures of CO and CO2, a reaction rate constant that is a function of both the total number of reaction sites of carbon, and the potassium content. The potassium dependency is taken care of by introducing activity coefficients for the carbon sites. As the first step towards such a model, a regression line for the Boudouard reaction rate has been established.

Jan 1, 2004

By S Adamson

Morphological analysis of alluvial gold recovered from the same segment of a placer by four common commercial methods indicates that gold shape and the presence of quartz intergrowths or sulphide overgrowths substantially influence the recovery efficiency of each method. The amount and types of gold saved by each method varies according to the different hydrodynamic conditions under which each of the methods operates. Reverse circulation drilling has the lowest efficiency and preferentially loses moderate-high flatness gold and intergrown or overgrown gold particles with relatively low density. Gravity riffle, hydraulic riffle, and jigcentrifugal concentrator systems respectively save progressively more of these problematic gold morphotypes, but still lose significant and sometimes substantial amounts (of profit) to the tailings. Because of the differences in recovery efficiency, reverse circulation drilling probably underestimates the grade of most placers and may have resulted in bypassing several economic deposits. Losses to tailings by commercial recovery plants arise from inadequacies in fundamental plant design features. These inadequacies compromise plant efficiency by limiting the ability of plants to simulate the wide range of hydrodynamic conditions necessary to operate effectively throughout placer systems. Incorporation of sand pumps and multiple recovery methods into the more sophisticated plants only partly overcomes these inadequacies. At best, efficiency will be maximised in a few segments of the placer determined by individual plant design, and will decrease progressively upstream and downstream of those segments. Without prior knowledge of the morphological characteristics of the gold to be mined, it is difficult to choose the most appropriate plant design, or to estimate what proportion of the gold will be recoverable by any given plant. If the relevant relationships are not considered beforehand, the recovery plant is likely to lose a significant proportion of the gold, and sacrifice maximum profit.

Jan 1, 2001

By Katri Avarmaa

Aluminum and copper are large volume metals in electronic appliances, while tin and indium exist as common minor elements. All of these non-ferrous metals are aimed to be separated and recycled from the end-of-life electronics into non-ferrous scrap fraction(s), and further through pyrometallurgical and/or hydrometallurgical processes to pure metals. Depending on the mechanical pre-treatment processes, aluminum and copper liberation from each other varies. This study focuses on the influence of alumina on indium and tin distributions between copper alloy and iron silicate slags with 0, 9 and ∼16 wt% of Al2O3. The experiments were executed with an equilibration-quenching-EPMA technique in an oxygen pressure range of 10−10–10−5 atm at 1300 °C. The metal-slag distribution coefficient of indium remains constant as a function of alumina in slag, while that of tin increases. Therefore, aluminum in feed or alumina addition to the slag improves the recovery of tin into copper. Nevertheless, oxygen pressure has clearly more significant influence on the behavior of both the metals in the smelting conditions.

This investigation was planned to determine:1. The precipitation-hardening properties of the copper-nickel-phosphorus alloys; and2. The influence of arsenic and bismuth, singly and together, on the mechanical properties of these alloys.It was carried out in conjunction with an investigation, previously published in these Prooeedings on "The Influence of Various Elements on the Mechanical Properties of Copper containing a small percentage of Bismuth," and also formed part of a study of the influence of bismuth, nickel and phosphorus on the properties of commercial arsenical-copper.The first part of the present investigation arose out of a discovery some years ago of precipitation-hardening in phosphorus-deoxidized coppernickel boiler tubes, containing approximately 2% nickel and 0·03% phosphorus, supplied to an Australian Railways Department. At that time there was little information available on precipitation-hardening in copperrich copper-nickel-phosphorus alloys, but at the end of 1935 a short paper on the subject was published by E. C. Rollason and T. G. Bamford(2) and at the beginning of 1940 a comprehensive account was published by D. K. Crampton, H. L. Burghoff and J. T. Stacy.(3) Although the investigation carried, out independently by the present author was not as comprehensive as that of Crampton, Burghoff and Stacy, the results are in agreement with those of the American as well as of the British authors; hence, only a summary of this aspect of the work is needed here to establish a basis for a study of the influence of bismuth and arsenic.PREPARATION OF TEST PIECESAll alloys were melted under charcoal in plumbago crucibles in an oil-fired furnace and were poured out of contact with air into oil-dressed moulds to give billets either 7· 5 in. long X 0.83 in. diam. X 1·3 lb. weight or 12 in. long X 1·125 in. diam. X 3·3 lb. weight depending on requirements (the larger size was used, for example, in establishing the annealing characteristics of the precipitation-hardening alloys). The raw materials were electrolytic copper of the composition described in the previous paper(I) 6% copper-arsenic, 14% copper-phosphorus, 1:7% copper-bismuth, and Mond nickel in the form of "shot." The method of producing test pieces from these billets and the annealing treatments ana tests to which the pieces were subjected have been described in the previous paper.

Jan 1, 1944

By William W. Leathen

Acid mine drainage became a reality through the exposure of the first bituminous coal seam, either by man or by nature. At first the small amount of acid formed was quickly and efficiently neutralized by basic rock strata and by neutral or alkaline water. As soon as extensive mining operations overtaxed nature's own defensive measures, acid mine drainage became a problem of concern to government and the coal industry. It was the purpose of the studies conducted at Mellon Institute to accumulate knowledge, both applied and fundamental, relating to the formation and disposal of acid mine effluents. It was during this program that the microbiology of acid mine water was studied. Most bituminous coal mine effluents are highly acidic and contain, along with other ions, high concentrations of ferrous iron. The acid is sulfuric, and. the iron is present as the sulfate; both are the oxidation products of iron sulfides (FeS2) which are present in the form of pyrites, marcasites, or other sulfuritic minerals. The oxidation occurs, in the absence of moisture, according to the following reaction: [ ]

Jan 1, 1959

By Newell R

The situation in which a gas stream flows through a bed of solids is found in many extractive metallurgy operations. Examples include blast furnace smelting, sintering and pellet firing. In such cases the resistance of the bed to fluid flow and heat transfer is of major significance to the operation of the process. This depends on the structure of the bed, which in turn is influenced by the manner in which the materials are charged to the bed. In this work, packed beds of hematite pellets of two different sizes were prepared in which the pellets were charged as a uniform mixture and in layers. The porosity, flow resistance and heat front velocity were measured and compared for the different bed configurations. For layered beds, the overall porosity and heat front velocity increased while the flow resistance decreased when compared with the values obtained for the uniform mixture. The size of the layers also had an effect on flow Properties.

Jan 1, 1991

By H. N. Lawrie

Introduction. THIS study was undertaken on account of the lack of definite knowledge concerning the influence of bismuth on wire-bar copper, and the small elimination of bismuth from copper-matte during the smelting-operations. The early workers who studied the influence of bismuth on copper confined their investigations to malleability and ductility-two physical properties which are related to the others so intimately that their determination is of primary importance. Karsten ' and Levol,2 using bending- and mealleability-tests, seem to have been the first to take up the subject, and while their results are incomplete, they agree in the main with the later work of Hampe.3 The bending-tests used by the first investigators consisted in bending the specimen until it failed. The malleabilitytests were made by beating the material to a knife-edge with a hammer. Hampe not only determined the percentage of bismuth which would cause red-shortness and cold-shortness of the alloy, together with other influences of bismuth on the malleability and ductility of copper, but also took up the influence of the bismuth protoxide, BiO, on copper, and of bismuth sesquioxide, Bi2O3, on the copper protoxide, CuO. Hampe's conclusions of the influences of these two latter compounds of bismuth on copper are as follows "If the protoxide of bismuth be alloyed with metallic copper, it is not changed to metallic bismuth, but remains mechanically distributed throughout the copper.

Sep 1, 1909

By Daniel Johansson, Markus Danielsson, Håkan Schunnesson

In sublevel caving, blasted material flows gravitationally into the drawpoint from above in a periodical manner. This type of flow behavior entails muck pile conditions that are variable along the course of extraction. The effect of this variability on the LHD (Load-Haul-Dump) operation in terms of loading efficiency and ability to undermine the blasted ring is not fully understood as of today. This paper presents results from a field test in LKABs Malmberget mine in Sweden, where the influence of fragmentation on the loading operation has been studied in detail. Drawpoint filming was conducted for extraction of two rings equivalent of roughly 10000 metric tons (~9842 long tons) of material each. The analysis includes fragmentation measurements, muck pile classification, and general estimations in terms of loadability. Further, an evaluation of LHD machines from two different manufacturers was conducted to identify and highlight differences. The results show that fragmentation, muck pile compactness, and flow characteristics are all interdependent. Flow disturbances and the subsequent loading of compacted fine material in the back of the ring have been identified as the main reason for occurring problems and prolonged digging times. However, the ability to sufficiently undermine the blasted ring has been identified to primarily depend on digging depth which is only observed to be high during flow disturbances. An absence of flow disturbances seem to promote high loading efficiency but simultaneously limit the maximum digging depth. A mid-range particle size distribution with a low amount of fines has proven beneficial for overall loading efficiency. The various LHDs employed showed significant variations in terms of ability to handle difficult loading situations (e.g. compactness, boulders, etc.).

Jan 1, 2018

By Cindy L. Williams

"The Blue Star subdistrict in the Carlin Trend, Nevada, includes multiple mines with 33.9 t Au in reserve and past production totaling 89 .1 t Au. The deposits are characterized by zoned alteration mineralogy and gold grades. From orebody centers outward the zones include: 1) a silicified core with erratic gold grade; 2) adjacent mill-grade (> 1.37 Au git) intense quartz-sericite-pyrite alteration; 3) enveloping leach-grade (0.21 Au g/t to 1.37 Au git) weaker sericite-kaolinite-quartzpyrite alteration; 4) surrounding decarbonatized and intensely argillized waste and leach grade ore; 5) pervasively decarbonatized waste rock; and 6) peripheral waste with weak decarbonatization and local propylitic alteration. Zoned alteration extends as much as 1500 m beyond orebodies.Understanding Blue Star subdistrict zoned alteration assemblages and gold grades has increased geologists' ability to provide practical and economically significant information to geotechnical engineers, mine planners and drill and blast personnel. Alteration influences geotechnical pitslope design because each assemblage has distinct rock strength. Geotechnical engineers use three-dimensional models of incompetent alteration types as a foundation for pit-slope design. In the drill and blast cycle, hard and soft alteration types require modified practices (powder column, blast hole spacing, delay design etc.) for optimum blast energy distribution. Further, geotechnically instable alteration types require careful blast procedures to prevent backbreak whic~ damages ultimate walls. In addition to mine planning and mining applications, zoned alteration assemblages extending beyond orebodies provide a useful exploration guide. Metallurgical character also varies with alteration type. Intensely quartz-sericite-pyrite altered or silicified ore has relatively high partical-size dependency and poor leach recoveries. Moderately sericite-kaolinite-quartz-pyrite altered rock, in contrast, shows little size dependency and good leach recoveries.The author sincerely thanks L. Schutz, P. Williams, C. Clode, W. Trudell, P. Herrera, M.DKunkel, M. Goings and numerous other Newmont geologists, metallurgist, engineers and support staff who made this paper possible."

Jan 1, 1997

By V. G. Papangelakis, G. A. Moldoveanu

"One of the major commercially viable secondary sources of rare earths elements (REE) are the ion-adsorption ores, containing 0.05-0.3 wt% rare earth oxides physically adsorbed on the surface of clay minerals formed during weathering of lanthanide-rich rocks. Although ion-adsorption deposits are substantially lower grade than other types of rare earth sources, this is offset by the easier mining and processing costs and the low content of radioactive elements. The conventional extraction route involves ion exchange leaching with monovalent cation solutions (usually ammonium sulphate) under ambient conditions; during the process, the lanthanides are desorbed and transferred into solution, being replaced by the exchange cation. While ammonium ions are known to perform best, there is increased environmental motivation to investigate alternative lixiviants in order to minimize ammonium sulphate impact via reducing its use without considerable loss in rare earth recovery.The objective of the present research was to screen various cations salts (alkaline and alkalineearth metals present as sulphates, chlorides and acetates, respectively) in order to comparatively evaluate lanthanide desorption levels and provide a theoretical base of the observed behaviour. The overall aim is to gain a better understanding of how both cation and anion may affect the overall REE recovery from ores in order to provide alternative processing routes. The distinct exchange capabilities of cations were explained in terms of differences in cation hydration enthalpy within the same group, i.e. Cs+ > NH4 + > K+ > Na+ > Li+ and Ba2+ > Ca2+ > Mg2+. For the same cation, it was determined that REE extraction efficiency follows the order sulphate > acetate > chloride, based on dissimilarities in constants of formation values. Various process implications scenarios will be described based on using mixed cations and anion matrices."

Jan 1, 2016