Search Documents

By R. S. Scheetz

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity: .the gas, itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used mining today are the vertically simulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Penn State coal methane simulation model.

Jan 1, 1989

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

The Effects of Collector and Grinding Environment on the Flotation Selectivity of Rosh Pinah Pb/Zn Ore

Sep 13, 2010

By Bin Xu, Qian Li, Ya-xuan Wang, Yong-bin Yang, Xi Zhang, Tao Jiang

The effects of common associated sulfide minerals including pyrite, arsenopyrite, galena and sphalerite on thiosulfate leaching of gold were studied in this work. Sulfide minerals had significant effects on gold leaching because that the dissolved products of sulfide minerals precipitated on gold surface to form coating layer. The degree of sulfide minerals impact on gold dissolution decreased in the order of pyrite ≈ galena > arsenopyrite > sphalerite, while the degree of effects on thiosulfate consumption decreased in the order of pyrite > arsenopyrite > sphalerite > galena. The additive CMC (Carboxymethyl cellulose) could not only reduce thiosulfate consumption but also increase gold dissolution. The mechanism of this might be that CMC could restrict the decomposition of thiosulfate by cupric ions and the precipitates on gold surface.

Jan 1, 2015

By Li Qihou, Li Yuhu, Liu Zhihong, Liu Zhiyong, Yang Xiaofeng

Scorodite samples were synthesized, in adding or without crystal seed respectively by using Atmospheric Scorodite Process (ASP), Hydrothermal Scorodite Process (HSP), and Improved Atmospheric Scorodite Process (IASP) individually; and their crystal structure, crystallinity, morphology, particle size, specific surface area, Fe/As mole ratio, as well as the leaching stability were characterized, aimed to reveal the relationships among the synthesis methods, the compositional and structural properties, and the leaching stabilities of scorodite. The results show that synthesis methods have significant effects on the compositional and structural properties of scorodite. Scorodite samples of high crystallinity, small specific surface area, and low Fe/As mole ratio, possess high leaching stability. The order in the leaching stability of scorodite samples synthesized in this study is as follow: ASP<HSP<IASP. Scorodite particles in the sample synthesized by IASP without crystal seed are in large sizes and of pyramidal morphology enclosed mainly by crystal planes of {111}; and the sample possesses the crystallinity of 84.5%, the particle size (D50) of 28.2 m, the BET specific surface area of 3.72 m2/g, and the Fe/As mole ratio of 1.05; after leaching this sample by using acetate buffer solution of pH 4.95 for 10 days, the total arsenic concentration in the leaching solution is merely 1.14 mg/L.

Jan 1, 2015

By H. B. Oblad

The WEMCO® SmartCell™ flotation machine is a continuously-stirred tank reactor in which solids are suspended in water and are contacted with air. The reaction is particle flotation resulting in the separation of valuable material from gangue. The effects of several operating variables on the flows of water and air and on motor power were measured. A miniature magnetic flowmeter was installed in the draft tube that allowed measurement of the water flows into the rotor. This work has led to a better understanding of machine function which will lead to improved performance and better operation. General equations for optimization, design, and scale-up were inferred.

Jan 1, 2002

By Les W. Armstrong, Stephen B. Richardson, Neville T. Moxon

A study was carried out to determine how different degrees of stemming confinement, that is the retention of the explosives gases, effects fragmentation and movement during blasting.

Jan 1, 1993

By J F. C L Costa, J C. Koppe, C Diedrich

Currently mineral resources evaluation is firstly expressed in terms of volume. Next the resources are transformed into tonnes by using an average bulk density applied to the whole deposit or, in some other circumstances, various different densities to distinct geological domains. Previous work in uranium, copper and nickel deposits used linear correlation between grades and bulk density to derive the density. Geophysics methods are also another good way to obtain density indirectly.These approaches do not take into account that two samples with the same grade but with different bulk densities can characterise different sample supports, leading to severe bias in grade and tonne estimates. It is important that the systematic measurements of bulk density are included into the estimation process, particularly when density is not correlated with the grades. Additionally, the extra time and costs involved in obtaining the bulk density data have made the mining industry disregard it.This study reports the impact in resource estimates by using a methodology that includes the bulk density variability. It involves the determination of a variability model for the bulk density and another model for the composite that was weighted by density as well as by its length. Next, these variables are estimated by kriging and the final grade estimates are obtained. The tonnages are obtained with the bulk density estimates. The conventional methodology was also applied and both estimates are compared to the reconciliation data from a major copper deposit. The results show a significant difference between the tonnage and grade estimates obtained from these two methodologies.The results show that considering density variability when compositing leads to a more accurate methodology resulting in better grade and tonnage estimates locally and globally.

Sep 26, 2011

By Michael C. Montoya, Craig Hopper

It has been well established that the ability to soft start a conveyor will give many benefits to the conveyor user. The effects of deceleration on belt tension have not been as extensively studied. This paper presents the findings of field measurements on the belt tension of a conveyor undergoing various rates of deceleration. The control of conveyor drive motors by Variable Frequency Drives (VFDs) allows the conveyor to be controlled during both acceleration and deceleration. The conveyor is allowed to ramp to a stop without putting unnecessary stress on the belt or conveyor structure.

Jan 1, 2000

By E. K. Soper

Introduction It has been observed that where veins or other types of orebodies are intersected by cross faults, the continuation of the ore deposit below the fault is often of lower grade than that portion above the dislocation.1 In some mines, the reverse of these conditions has been noted, and the richest ore is found to occur in that portion of the vein beneath the fault intersection. Such instances seem to be less frequent than those where the richest ore is above the offset. The important and widespread influence of fault and vein intersections upon the localization of ore shoots is well known 2 but the factors that govern the position of the ore shoot relative to the fault intersection seem to be less clearly understood. The richest ore may be above or below the fault,. or it may occur at-the point of intersection, or there may be no change. Recent observations made by the writer in mines in Idaho and Montana suggested a possible explanation for the changes in the richness of ore below certain types of fault intersections. These observations have been supplemented by a study of the literature containing detailed descriptions of ore deposits at a large number of mines in North America. The results of these studies are presented herewith in the hope that they may lead to further discussion of this important phase of ore deposition.

Jan 10, 1917

By A. Wahib Khair

"This article first describes the impact of respirable dust on the health of miners in underground coal mines in the United States of America. Second, it identifies the major sources of dust generation, namely cutting tools in the road headings. Two surveys associated with cutting tools were made to determine the useful life of these cutting tools, and to determine the effect of cutting tool wear on productivity of the continuous miners. Third, this article presents the results of a series of experiments carried out in the Rock Mechanics Laboratories at West Virginia University in order to study: 3.1 the effect of cutting tool rate of wear on respirable dust generation, 3.1.1 the effects of rock materials on tool wear and respirable dust generation, 3.1.2 the effect of cutting tool geometric parameters on respirable dust generation, and 3.1.3 the effect of tip materials used in the cutting tool on respirable dust generation. Recommendations in regard to cutting tool design are also presented in this paper.Silica and coal dust are the two major elements affecting the health of underground miners. According to Lemen [1] approximately 1,500 men died due to breathing in silica dust in 1936 while tunneling through a mountain of mostly silica, near the town of Gauley Bridge, West Virginia. Coal dust resulting in lung diseases in one of the major health hazards in underground coal mines. The impact of black lung on miners, coal workers' pneumoconioisis (CWP), has ranged from 16,000 to 23,000 each year since 1982 [1].The trend for conventional mining to continuous machine cutting of coal, using more productive machinery, is inexorable. Intolerable level of dust generated at the face is an indication of inefficient coal/rock cutting by these machines. The federal goverment of the United States paid about 11.7 billion dollars in workmen's compensation to more than 470,000 miners with CWP [2]. Bieniawski and Zipf [3] reported that annual benefit payments were about 2 billion dollars. The enactment of the Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanisms and cutting tool designs.The surveys concerning the utilization of cutting bits and performance of continuous miners in underground coal mines were made in order to have first hand information about bit consumption and coal produ¬ction.Three types of used bits, commonly utilized cutting tools on continuous miners, were collected from different coal mines. The used bits were grouped into symmetrically and asymmetrically worn bits. Distribution analysis for weight loss and conical height loss was done. Details of the results are presented elsewhere [4], here the results are summarized briefly. The analysis shows that approximately 50% of the collected bits have worn asymmetrically, which shows that many bits do not rotate properly during cutting. Analysis of the distribution of bit wear showed that the degree of bit wear varied from one type to another and with mining conditions. On average, the weight loss of the used bits was 4% to 7% with a maximum of 31%. Correspondingly, the loss of the conical height was observed to vary between 11% and 23% with a maximum of 71%. Figure 1 shows typical data associated with some of the used bits."

Jan 1, 1998

By Emre Biringen

"Results from a small-scale laboratory experimental program show the changes in the vertical stiffness and strength of a soft clayey soil adjacent to the shaft of an inserted pile (i.e. expansion of a cylindrical cavity). The experimental program provides a realistic axi-symmetric physical model of an element of a cylindrical pile and the surrounding soil. The study interprets the improvement and assesses its magnitude in vertical stress-strain-strength properties of a normally consolidated soft cohesive soil in response to preloading impact in the radial direction. The results verify that insertion of a cylindrical pile causes densification of surrounding soil in a radial direction due to change in stress state around the pile, and thus consolidating and stiffening of the soil.The test results indicate that most improvement in modulus and strength takes place within a distance of 4 times the radius of a pile, though significant improvement is realized to a distance of 8-10 times the radius, beyond where there is negligible effect. Settlement characteristics of the surrounding soil in a zone of 12 times the pile radius improve significantly after the formation of a cylindrical cavity. The miniature vane shear strength tests show a 1.5 times increase in a zone of 4 times the pile radius compared to the strength at 10 pile radii. The results also imply that the spacing of cylindrical piles should not be more than 4 to 10 times pile radius, so that the surrounding soil matrix may improve the vertical bearing capacity under any foundation or embankment loading.INTRODUCTIONThe engineering community is familiar with different techniques to improve the bearing capacity and settlement characteristics of weak cohesive and organic soils. Some of the in situ techniques to improve the properties of soft ground (e.g. soft clays) prior to placement of foundations are vertical preloading, deep cemenUlime mixing, stone columns, and grouting (Henn 1996; Moseley 1993). In addition to these methods, researchers have recently showed interest in achieving soft ground improvement by means of applying radial compression method for which different names exist including expanding pile (Kelleher et al. 2001 ), Preload™ Pier (Biringen and Edil 2003), and sand compaction pile (Lee et al. 2004). Handy (2001) has described how preloading can also be achieved by imposition of radial loading in soft ground with an expected improvement in stiffness. The idea behind the latter method is densification and consolidation of soft soil in the radial direction by controlled displacement for which the process can be viewed as a cavity expansion problem (Vesic 1972)."

Jan 1, 2005

By J. A. Finch

"This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified. IntroductionThis paper summarizes the findings of a detailed review of available technical information on the operation of rod mills. One of the basic problems in historical comminution testwork has been the lack of a standard measure of circuit performance. The Bond Operating Work Index, not introduced until after 1950, has proven of immeasurable value in this regard, but first has to be carefully considered in terms of its utility and limitations. Its prescribed use is described in a later section of this paper.During this review, it became apparent that rod mill performance is generally not well understood. Because of combined interactions, the effects of different operating variables may be difficult to assess, and even at times appear erratic. It is obviously difficult to rationalize plant testwork or circuit adjustments when the results are highly unpredictable. The purposes of this review, therefore, were:a) to establish what basic facts have been learned about rod mill performance;b) to define some genera l guidelines for efficient rod mill design and operation; and,c) to establish a basis for specific recommendations for plant tests or adjustments with minimum risk, and maximum potential for circuit performance improvement."

Jan 1, 1986

This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified.

Jan 1, 1986

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be re-handled. Prior studies have shown that by only changing blast hole timing with the same blast design, fragmentation and throw alters. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum inter-hole delay for fragmentation has been found by studying timings from 0ms to 45ms. Instantaneous timing between holes increased the throw by over 100 ft, but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw. This paper investigates this optimized inter-hole timing while altering top and bottom column primer time to potentially improve throw while maintaining optimum fragmentation. Timings studied are top initiation, bottom initiation, and top and bottom simultaneously. INTRODUCTION Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading, and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.” Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is re-handled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators has allowed for precise delay timings to be used between rows, holes, and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation. This study consisted of 3 full scale bench blasts at a granite quarry in Talbotton, GA. Each blast was characterized by the timing delay between the top and bottom primer in the blast column of each hole; one simultaneous blast with a 0 ms delay, a bottom-initiated blast with a 1 ms delay, and a top-initiated blast with a 1 ms delay. Fragmentation analysis of the resultant muckpiles was performed using a combination of the PortaMetrics handheld point-and-shoot rugged tablet from Motion Metrics and the software WipFrag from WipWare. Throw was measured by placing strategic distance markers on the floor of the bench and then taking overhead photographs of the muckpiles after each blast. High-speed video footage was captured of each blast using an MREL Blaster’s Ranger II camera."

Jan 1, 2017

By Eugene V. Cilento, George B. Georgellis

The hypothesis that freshly-sheared quartz makes it more reactive in lung tissue than aged quartz was tested by its ability to stimulate superoxide anion (02-) release from single adherent pulmonary alveolar macrophages (PAM). Fresh quartz was prepared by grinding for 30 min and then used within 2 hr, while stale quartz was from the same stock but aged 15 days prior to use. Also, dipalmitoyl lecithin (DPL), the major constituent of lung surfactant coating the alveoli surfaces, was coated onto the particles. Release of 02- was measured after 40 and 180 min of direct contact with quartz dust (225 µg/ml). Fresh quartz was more reactive than aged quartz, as indicated by the 78 and 63% increase after 40 and 180 min, respectively. A time delay and suppression of 02- release was observed in the ability of the DPL- coated fresh or stale dust to stimulate PAM. These results supported the hypothesis that the natural process of surfactant coating of inhaled particles in the alveoli may play a role in their phagocytic removal by PAM.

Jan 1, 1991

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA), U.S. Department of Labor, employees who serve as accident investigators for serious accidents and fatalities as part of their job duties. The subjects responded anonymously during a workshop on stress. The subjects consisted of randomly selected individuals, representative of locations across the country and representative of all mining commodities: coal, metal, nonmetal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalization, and reduced personal accomplishments. The average results of the scores for each of the three subscales fell in the moderate range for the study group of MSHA accident investigators. The scores within the moderate range show that the subject population was at the lower end of the range for emotional exhaustion and depersonalization, tending toward a lower burnout risk, while the group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. It is concluded that overall this group is at moderate risk for burnout, and the authors recommend follow-up with this population.

By Robert E. Barrett

The history of mine safety legislation in this country is also a history of mine explosions. Nearly every piece of safety legislation that has been introduced or amended has resulted from some type of a disaster. When coal was first discovered and mined, it was extracted from along outcrops. As the coal became depleted near the surface, underground mining developed. When the first mine penetrated the outcrop, a great number of problems developed, many of which remain with us today. One of those problems is the potential for mine ignitions and explosions. Naturally, when underground mining progressed a few feet into the outcrop, some type of artificial light was needed. Early accounts of mining in Spain, Italy, Japan, and Great Britain indicate that torches served to light the mines. Later, candles were used, and still later, earthern oil lamps containing fish oil were used. As workings got deeper, explosions began to occur. When one did occur it was thought to be the work of goblins or the devil. As explosions became more frequent, it became very obvious that the use of open flames for lighting was very dangerous. A substitute was sought. Dried fish skins which gave off a weak phosphorescent light were tried. A mixture of flour and lime made from oyster shells called Canton phosphorous was also tried unsuccessfully. Fireflies in a bottle were also used.

Jan 1, 1976

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By Dale S. Preece, Stephen H. Chung

Electronic detonators and the attendant precise detonation timing that they facilitate are having a measurable effect on rock blasting in terms of improved fragmentation and vibration control. These improvements are increasingly well documented which is driving the expanding use of electronic detonators. In spite of the growing body of positive evidence concerning the benefits of precise delay timing, very little work has been done to document the impact of electronic detonators on the movement of rock. In this study 3-D computer programs, used to predict blasting induced rock heave, including the effects of detonation timing, are used to simulate the effect of precise timing on rock movement. Implementation includes quick, precise timing between blastholes going down a row and then much longer delays between rows of blastholes. For example an effective blast design might call for precise 3 ms delays between blastholes along a row and then 60 or 72 ms between rows. Several options are studied in this paper using computer simulations to draw some conclusions about the underlying physics affecting the process and how precise timing might have a positive impact on blasting induced rock motion.

Jan 1, 2005