Search Documents

By C. Sui, J. E. Nesset, M. Li, J. Y. Kim, S. L. Chryssoulis

"A plant study of zinc rougher flotation at Brunswick Mining was conducted using lime, soda ash and a combination of both as the pH modifiers in order to establish the effects on sphalerite and pyrite kinetics and mineral selectivity. The plant sampling and analysis was augmented by surface analysis using TOF-LIMS, SEM and XPS as well as fundamental precipitation and surface-charge studies in the sphalerite Ca/C03/S04 system.The results revealed the important role of carbonate ions in cleaning the sphalerite surface for effective activation by CuS04 to occur, and the beneficial role of combined soda ash and lime in increasing pyrite and galena depression.1.0 IntroductionThe studies reported in this paper were initiated as part of an investigation into the causes of a particularly pronounced seasonal deterioration in metallurgical performance at the Brunswick Mining concentrator during the summer of 1995. The concentrator treats a complex base metal ore having a typical feed composition of 9.0% Zn, 3.5% Pb, 0.4% Cu and 100g/t Ag at a current throughput of 9,000 TPD, although at the time of the problem in 1995, the average production rate was closer to 10,500 TPD. Zinc, lead, copper and bulk (zinc-lead) concentrates are produced with overall metal recoveries of 86% zinc, 63% lead, 60% copper and 60% silver; results which are typical of the lower recoveries associated with fine-grained, highly complex VMS and SEDEX type deposits. The main economic minerals of interest are an iron-containing (7% Fe) sphalerite, galena and chalcopyrite with the main diluent (about 60% wt) being pyrite.Figure 1 shows a simplified flowsheet of the Brunswick milling circuit while the seasonal decrease in summer metallurgy in 1995 is illustrated in Figure 2. Of significance is the rapid drop in copper and lead recovery in June while there is an apparent delay until late August-September before the zinc deterioration reaches its lowest point. A more typical seasonal effect within the experience of the authors is the reverse of the Brunswick situation, namely an improvement in summer performance thought to be associated with improved differential flotation kinetics during warmer weather leading to better mineral selectivity. The historical Brunswick experience was particularly severe during the summer of 1995 with estimated incremental losses of $10 Million for this period. The potential of the very significant economic benefits to be gained from understanding and hopefully improving the annual drop in performance led to an investigation involving the minesite metallurgical group, the Noranda Technology Centre (NTC) as well as researchers in Professor Jim Finch's group at McGill and the surface analytical services and interpretive skills of AMTEL."

Jan 1, 1998

By Madgwick J. C

Leaching column techniques and microbiological methods have been described in detail in Madgwick and Ralph (1980) and Madgwick, Ralph and Sadler (1981).Sixty-nine kilograms of copper porphyry ore (0.4 per cent Cu, 2.7 per cent Fe) (particle size 2.4-11.2 mm; 60 The effect of sodium chloride (O.6M) irrigation on bacterial leaching of Bougainville copper porphyry ore was studied.Viability of suspended Thiobacillus ferrooxidants was reduced to less than 10 cells/ml in NaCI (O.6M) compared with 10' eells/ml in dilute II,SO, (0.01 M, pll 2). Salt irrigation had no significant effect on heterotrophic and sulphur oxidizing bacteria. Increascd short term recovery of copper (145 g/tonne/ 15 days) was followed by a marked decrease in tenors to less than 20 mg/litre/day compared with an acid leach, steady release, of 110 mg/litre/day. Resumption of acid leaching restored average solution copper to 46 mg/litre/day and the viability of suspended T Ierrooxidates to 10 cells/ml.Quantitative removal of sodium ehloride from ore particles was difficult and t races of NaCI remained for more than 200 days.

Jan 1, 1982

By F. F. Aplan, G. Simkovich

Zinc oxide, an n-type semiconductor, and nickel oxide, a p-type semiconductor, were studied in electrostatic separation experiments in pure and doped forms. In addition, pure potassium chloride and potassium chloride containing one volume per cent silver were also investigated. It was found, in agreement with theory, that the presence of dopants in the oxides could either increase or decrease the electrical conductivity of the base compounds and, thus, control the response of these particles to electrostatic separation. Further, it was shown that the same dopant in the n- and p-type semiconductors produced opposite conductivity effects; again in accord with theory. Finally, it was found that the presence of dispersed silver particles in the normally insulator phase potassium chloride produced sufficient electronic conductivity to cause the silver containing particles to respond as would materials possessing "medium-type" conductivities.

Jan 1, 1980

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By B Tadesse, L G. Dyer, B Albijanic, M Jung

The presence of high concentrations of dissolved ions in groundwater, sea water or recycled water may alter the water structure, particle surface wettability and colloidal interactions between bubbles and particles and can have a significant effect on mineral flotation. While the impact of water quality on the flotation of precious and base metal minerals is well established, no relevant published study exists currently regarding the effect of water salinity on the flotation of rare earth bearing minerals. This paper attempts to quantify the effect of water quality variation on flotation recovery and grade of rare earth minerals and gain an understanding on which ions existing in saline water affect flotation behaviour. Specifically, it is aimed at investigating the effects of water quality on the flotation of monazite in the presence of cations such as Ca2+, Mg2+, K+, and Na+. Flotation tests, zeta potential measurements, and adsorption tests were performed to explain the flotation behaviour. It was found that monovalent ions such as Na+ and K+ have negative impact on rare earth minerals recovery and grade. The result of single mineral flotation tests showed that the floatability of monazite was significantly depressed in the presence of Ca2+ and Mg2+. The result of single mineral flotation test showed varying depression levels in the presence ions in the order of Ca2+ > Mg2+ > Na ~ K.

Aug 24, 2022

By James A. Finch, Xiangzhou Ding, Yue Hua Tan

"The Jameson Cell is one of the choices of flotation machine in coal, base metal processing and other specialist applications. This paper determines the effect on vacuum pressure and bubble size of two design variables, orifice size and downcomer length, and the operating variable air-to-water (AWR) ratio. The main findings are: orifice size and downcomer length impact the vacuum but have limited effect on bubble size; AWR < 1 favours high vacuum, conditions are identified where vacuum is maintained at AWR > 1, and water flowrate has slightly greater impact on bubble size than air flowrate.INTRODUCTIONFroth flotation, the most common technique for mineral separation, has been in use for over a century. The process takes advantage of the difference in wettability of mineral surfaces to achieve the separation of valuable minerals from non-valuable minerals, or gangue. Numerous flotation machines have been invented and patented over the years. The Jameson Cell, invented by Professor Graeme Jameson in the late 1980s, is one successful example. First trialed at Mount Isa Mines (Queensland, Australia), Jameson Cells have been installed at operations around the world for the recovery of fine coal (Mohanty and Honakeri, 1999; Cowburn et al., 2006; Hacifazlioglu and Toroglu, 2007; Uçurum 2009), minerals of copper (Farr 1992; Atkinson et al., 1993; Harbort et al., 1997), lead/zinc (Rohner, 1993; Munro, 2003) and gold (Bennett et al., 2012; Lauder et al., 2003), and in water treatment (Yan and Jameson, 2004), solvent extraction de-oiling (Miller and Readett, 1992; Miller et al., 1997; Harbort et al., 2003; Young et al., 2006), oil sands processing (Neiman et al., 2012), and various food industries (Brenneman, 2014). One of the largest units is the 650 cm diameter separation tank with 24 downcomers installed in an Anglo American operation (Osborne and Euston, 2015). Scale up is relatively straightforward: to increase capacity the number of downcomers is increased with corresponding increase in size of separation tank.The Jameson Cell comprises two main parts: a vertical tube (downcomer) which provides self-aspiration and intense bubble-particles contact, and a (separation) tank where particle-bubble aggregates disengage from the pulp. The intense bubble/slurry mixing in the downcomer with air holdups reaching 60% (Marchese et al., 1992) accelerates particle collection enabling the greatly reduced cell volume compared with mechanical flotation cells and columns. The disengagement of the particle-loaded bubbles from the slurry in the separation tank is usually aided by addition of washwater."

Jan 1, 2018

By Helmut Thielsch

IN recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsification and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.1 In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously.2,6 From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time-i.e., improving the plant efficiency-great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. APPARATUS The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2 ½in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1946

By Stephen C. Tadolini, Yunqing Zhang, Thomas M. Barczak

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high-loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

By Stephen Tadolini

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high¬loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

Jan 1, 2003

By J. A. Wates

Stope backfilling in South African gold mines uses the coarser cyclone fraction of the gold tailings. The disposal of the overflow from the cyclones, which is finer and of higher moisture content than normal gold tailings, presents some problems. This paper describes an investigation undertaken to define the parameters that are required for a quantitative and qualitative assessment of the operation and stability of slimes dams built of such material. However, seeing the investigation was conducted on the slimes from only one mine, it is recommended that, until a wider range of data becomes available, tests should be conducted for each individual mine.

Jan 1, 1988

By A. P. E. Dirige

In order to maximize the recovery of ore in variably dipping ore zones of moderate width, cemented backfill is normally placed to serve as structural support. With the intention of saving on costs, backfill of low cement content can be used, which are often supported by a sillmat of higher strength. The stability of the low cement backfill face, exposed during adjacent mining, must be carefully studied to provide very effective, safe and economic mining operations. Improper design of these stope support structures may result in fill mass failure resulting in relaxation and failure of the stope walls, with consequent losses of production, ore dilution, and in safety problems. This paper presents a study conducted to assess fill performance during adjacent pillar mining and to provide a comprehensive understanding of backfill behaviour, the failure modes that may occur and the consequences to production, ore dilution and to safety problems, and accurately predict their stability. The design study investigated the effects of stope width and height, orebody geometry and inclination, and wall roughness on the stability of cemented backfill during adjacent pillar mining. Fill properties used were based on paste fill specimens cured for 28 days. Paste fill performances were assessed based on analytical and numerical modeling studies for the different mining conditions. Analytical modeling was carried out using limiting equilibrium analysis and numerical modeling was carried out using FLAC3D. The modeling results suggested that, for stopes that are inclined with smooth wall rock conditions, backfill failure, driven by the fill self-weight, has minimum dependency on the binder content and is reduced by resisting forces developed on the footwall-fill contact. For inclined stopes with rough wall rock conditions, wall roughness contributes significantly to the stability of the backfill during adjacent pillar mining. The analytical modeling approach was demonstrated to be useful in providing some approximate parameters for predicting the behaviour of paste fill exposed faces during adjacent mining, but cannot predict the mode or mechanisms of failure. Numerical modeling not only assess the stability behaviour of paste fill free faces, but also is able to provide a better idea of paste fill failure modes and possible failure mechanisms. The depth of failure and the potential for instability for a simulated stope filled with paste fill can be predicted, and may be useful in estimating the mass of material that could possibly fail and ore dilution levels.

May 1, 2009

By William A. Dupree, Mark J. Schultz, William J. Francart

Maintaining intake escapeways clear of contaminants from mine fires has been an issue for many years. Removing fire sources from these entries reduces the risk of contamination greatly. In recent years, concerns have been raised related to contamination of the intake escapeways by leakage when fires occur in adjacent airways. This paper discusses measured leakage rates for multiple stoppings at various pressure drops across stopping lines in a number of actual coal mines. Also addressed are methods for reducing the contamination risks for the intake escapeways, considering the ventilation system employed. The Effects of Air Leakage The effects of air leakage through ventilation controls has been well documented. While normal leakage is expected through stoppings, overcasts and other structures, abnormally high leakage results in an inefficient ventilation system and can increase operational costs for a mine. In addition, excessive leakage results in less control over mine ventilation airsplits. This may compromise the isolation of mine escapeways, and allow adjacent entries to be rapidly contaminated by products of combustion in the event of a mine fire. A study was conducted at ten mines in which air pressure and quantity measurements were taken near the active sections. The method used to construct the ventilation controls to separate airways was also noted. Stopping Construction Table 1 shows the type of stopping construction commonly used in the 10 mines included in this study. Main entry stoppings were normally built with mortared joints (wet stacked) with sealant applied to the high pressure side of the stopping. In most cases the entire face of the stoppings were sealed. In one case only the joints between blocks were sealed but the perimeters were sealed in all cases. Some mines also sealed the low pressure side of the stopping. Solid blocks were normally used for main entry construction and hollow blocks were sometimes used for longwall panel development. [ ]

Jan 1, 1993

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By B. Z. Weiss, N. R. Comins, F. Blum

Some aspects of the mechanical behaviour of chromium-containing dual-phase 3CR12 steel were investigated as a function of the temperature and strain rate. The yield stress was found to depend on both the temperature and the strain rate, with no substantial differences between the longitudinal and the transverse directions. The strain-rate sensitivity decreased with increasing temperature. The yield stress could be presented as a function of a temperature-strain-rate parameter. Impact test results showed substantial differences between the energy absorption of the transverse and longitudinal specimens above the ductile-brittle transition temperature. Changes in energy absorption with temperature were gradual for specimens in both orientations, and the transition from ductile to brittle behaviour occurred between 373 and 173 K. Strain rates ahead of the tip of notches with different geometries were calculated and measured experimentally.

Jan 1, 1990

By M. Jahazi, P. P. Bhattacharjee, K. Chadha

The present work investigated the effect of strain reversal during high pressure torsion on the evolution of microstructure, texture and hardness properties of two different materials with different dynamic recovery behavior, namely, high purity (99%) Aluminum (2N-Al) and Aluminum-Magnesium (Al-2.5%Mg) alloy. In the two aluminum alloys subjected to different routes, the evolution of the ultrafine structure followed same trend. At lower strain level, sub grains with prominent LAGBs network were observed and at higher strains, ultrafine equiaxed grains separated by HAGBs were observed throughout the disk. The texture evolution in monotonically and strain reversal processed 2N-Al and Al-2.5%Mg showed presence of typical torsion texture components at different strain levels. The strength of the components was observed to follow different trends depending on the processing routes.

Jan 1, 2015

By J Slade, R Trueman

Unplanned dilution has the potential to seriously undermine the economic viability of a mine, and in some cases results in mine closure. The effect of stress damage on dilution has become increasingly relevant as mining depths increase. In the case of narrow vein mining, the incremental extraction of long-hole rings has the potential to result in a moving high stressed zone at the stope brow. This leads the hanging wall and footwall to experience a spike in the stress to strength ratios as the brow passes. In some cases, the stress to strength ratio may be high enough to result in fracturing or damage to the rock mass. The aim of the study described in this paper was to investigate whether stress damage results in a significant increase in dilution. The study involved analysis of overbreak from 410 case studies from the Kundana Gold mine in Western Australia. Site personnel had already undertaken calibration studies of the stress levels that result in rock mass damage. This calibration, in conjunction with numerical modelling showed that stress damaged stope walls at this mine had on average 50 per cent more overbreak than stope walls where stresses had not exceeded the damage criterion. For a design mining width of 1.5 metres, and with both walls impacted, this represents 36 per cent increase in dilution. After adjustment for possible sources of bias the difference reduced to an average 0.10 metres per stope wall, representing 13 per cent dilution for the mining width under consideration. The potential for stress damage related overbreak should therefore be considered as part of any assessment of narrow vein dilution.

Jan 1, 2005

By R. W. Hughes, R. Koopmans

This paper investigates the effect of varying stress levels on the determination of deformation moduli and examines the sensitivity of the borehole dilatometer in measuring rock mass scale features and its ability to represent rock mass characteristics. Cubical blocks of sandstone, limestone and granite were tested in the laboratory under triaxial stress conditions. Field programs were conducted in both granite and sandstone rock masses surrounding underground openings. The dilatometer&apos;s zone of influence was determined by conducting tests within an instrumented concrete cylinder and by performing a finite element analysis. Laboratory and field results suggest that the deformation modulus of a rock mass can be substantially affected by the stress field and that the borehole dilatometer is sensitive enough to profile deformation moduli as dictated by the in situ rock mass characteristics.

Jan 1, 1986

By James G. Tilton

Subsidence resulting from mining operations, has been the object of sporadic study for many years. Reports have shown that subsidence has ranged from minor settlement detected only by precise measurements to great slips where buildings are destroyed, roads disrupted, and large fissures opened at the surface. For years, a controversy has raged over the question of whether there is a positive or negative angle-of-draw. None of these questions can be given a flat answer for the variables controlling, subsidence are infinite. Generalizations can be made for various situations and areas but some means of control must be executed.

Jan 1, 1966

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

By Tumilty JA, Schmidt CG

Sulphide ion is a powerful poison in gold cyanidation, however, the detrimental effect is less severe in plant practice. This is thought to be due to the presence of depassivating elements in the ore, mainly lead. Trace amounts of lead can counteract the poisonous effect of considerable amounts of sulphide. The reaction is instantaneous and is likely to be a direct involvement in the electrochemical surface reaction. Lead addition cannot be regarded as an all-round cure when experiencing poor leach efficiencies. A possible beneficial effect depends on the mineralogy of the ore and has to be determined individually for every material.

Jan 1, 1989