Search Documents

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years, the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture, and the ductility values can often be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel, Several types of abnormal loss of ductility can be distinguished, of which those caused by excessive amounts of inclusions of undesirable type and those caused by unsuitable grain size and ingot structure are well known. The particular type of abnormal lowered ductility currently under consideration may be distinguished by the fact that the low-temperature aging treatment necessary for its relief is insufficient to cause any visible change in the microstructure as ordinarily observed. As this aging will in fact eventually occur at room temperature, the phenomenon of present interest may be given the symptomatic definition, "Temporary Abnormal Low Ductility." Some hundreds of previous investigations, largely qualitative in nature, have established, beyond reasonable doubt, that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen-, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, The Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. The interest of this investigation thus extends to permanent abnormal losses of ductility, such as are caused by the inclusions which sometimes result from special deoxidizing practices and possibly from metallic nitrides, but as these can be distinguished from the temporary effect of hydrogen, they have been excluded from the work reported here except when they

Jan 1, 1948

By J. Wiese, K. Corin, Z. Song

"Relating flotation performance to the electrochemical characteristics of a pulp is complex both in fundamental research and in practice. In the case of thiol collectors, different Eh values in the flotation system can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system. A variation in pulp potential may also be achieved by the addition of potential modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). There exists anecdotal evidence which suggests that the addition of small amounts of H2O2 to the flotation process can improve sulphide mineral recovery. The objective of the present study was to investigate the effect of the addition of the potential modifier, H2O2, on sulphide mineral recoveries and grades in the flotation of sulphide minerals from two copper bearing ores from China and compare the results to those obtained for a PGM bearing ore South Africa. Batch flotation tests were conducted using the three different ores at the natural pH of the different systems, in the presence of a xanthate collector and the absence and presence of H2O2 as a potential modifier. The results indicate that the addition of carefully controlled low concentrations of H2O2 resulted in improvements in flotation performance. INTRODUCTIONElectrochemical potential as a control parameter in the flotation of sulphide minerals has been widely studied (Allison et al., 1972; Gardner and Woods, 1979; Ross and Van Deventer, 1985; Chander, 2003; Woods, 2003; Javadi, 2013). There is concensus that in order to be recovered during flotation, sulphide minerals require a suitable redox environment. During the flotation process thiol collectors and sulphide minerals are involved in electrochemical reactions which result in the formation of hydrophobic species at the mineral surface (Finkelstein and Goold, 1972; Rand and Woods, 1984). Sulphide minerals act as semiconductors and electrons are transferred during the interaction of the mineral with collector. The resultant potential difference and its magnitude are responsible for the transfer of electrons and the rate of the reaction (Bard and Faulkner, 2001; Fuerstenau et al., 2007). Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, may be manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system (Heyes and Trahar, 1979). The use of potential modifiers viz. reducing or oxidizing agents which include H2O2, NaClO, and NaHS, is an alternative method by which to control the potential of the pulp in a flotation system which may or may not promote the flotation of desired minerals (Rao, 2004). The oxidizing agent, H2O2, undergoes a cathodic reaction which can result in the enhanced flotation of valuable minerals. The potential of the system is increased which results in a shift in the mixed potential of a mineral. The magnitude of the over-potential influences the rate of the oxidation process and thus the flotation response of sulphide minerals (Kocabag and Guler, 2008). Equation 1 shows the proposed oxidation of xanthate by H2O2 (Lipkina and Streltysn, 1970)."

Jan 1, 2018

By Corale L. Brierley

The effect of hydrogen peroxide (H2O2) on growth and respiration of Thiobacillus, thiooxidans, and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uranium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were inhibited after contact with 0.82 mM H2O2. Inhibition of oxygen uptake by T. ferrooxidans occurred at 8.24 mM H2O2, and growth was inhibited after 6 hours exposure to 2.06 mM H2O2. Higher concentrations of H2O2 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface. INTRODUCTION In recent years, hydrometallurgical processes for recovery of metal values from low-grade ore minerals have played an increasingly important role. Dump leaching of low-grade copper waste materials in the western United States now yields 11.5% of the total U. S. copper production. Although scavenger operations in uranium leaching have been successful, the state-of-the-art of in-situ

Jan 1, 1977

By R. Stocker

Flotation recovery of molybdenite particles finer than 15 micrones sharpy decreases with decreasing size. A totally hydrophobic latex agglomerant (UBC-1), which was previously reported to be very efficient in agglomerating hydrophobic fine coal, has been found to agglomerate fine molybdenite particles. The agglomeration takes place only in the presence of MIBC which is commonly used as a frother in molybdenite flotation. Adsorption tests confirmed that MIBC is adsorbed onto molybdenite. The effect of the agglomeration on flotation has been studied by floating fine molybdenite from mixtures with quartz using the UBC-l agglomerant and the MIBC frother. A significant improvement in the flotation of fine molybdenite has been observed in the presence of the UBC-l agglomerant. The best results have been obtained around pH 5.5 which corresponds to the iso-electric-point of molybdenite.

Jan 1, 1997

By A. W. Khair

This paper deals with the analysis of pillar failure in a room and pillar mining operation of a deep underground coal mine. The incident here involved the failure of more than 100 pillars. The mechanism of pillar failure (bump/squeeze) has been studied in detail. The analysis consists of inmine eyewitness observations, laboratory experiments and analytical study of the pillar failure area using finite element technique. Results indicated that the mechanical properties of coal, roof and floor, geologic condition, and the method of operation have affected the mode of pillar failure. Hard roof and floor prevented roof caving and floor heaving in the gob area creating an inhomgeneous stress field on the pillar. This condition developed a yield zone and a core zone in the pillar. Progressive increase of vertical stress further increased the yield zone of the pillar and reduced the core pillar leading to a total squeeze of the pillar. However, the analysis indicated that the pillars were liable to bump provided any sudden shift of load occurred on the core pillar due to some dynamic shock imparted by a local failure of the immediate roof (slickenslided area) or during splitting.

Jan 1, 1986

By A. A. Sirkeci

In the scope of this investigation comparison between impact breakage and compression breakage were carried out for the separation efficiency of minerals using a chromite ore sample. The ore sample was broken below 1 mm employing a laboratory type roll crusher and an impact crusher. Concentration tests were conducted on -1+0.5 mm, -0.5+0.2 mm and -0.2 mm size fractions using a Wilfley type shaking table. Test results showed a remarkable difference between two types of breakage. Both concentrate grade and recovery was in the favour of impact crushing. Furthermore, the shape of the broken particles also showed differences such that in the case of impact breakage they were more spherical compared to compressive crushing. The results of the shaking table con-centration tests showed that a concentrate assaying 48.4% Cr2O3 were obtained with 78.5% recovery in the case of impact breakage. On the other hand the concentrate grade and recovery values were 48.8% Cr2O3and 52.4% respectively in the case of compression crushing. The losses in the tailings were also in favour of impact breakage proving that differential breakage occurred between chromite and gangue minerals.

Jan 1, 2014

By Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, G. M. Walker, N. Iles, R. D. Chandler, Regis Stana, B. Duddy, Patrick Zhang

Phosphoric acid is a major raw material for the production of ammonium phosphate (AP) that is used as an intermediate in fertilizer production. Impurities within commercial grade wet process phosphoric acid are important in producing a fertilizer granule with good handling properties. The impurities identified as being important are; iron (III), aluminium and fluorine-containing compounds. Results show that the viscosity of the AP slurry produced increases by increasing the amount of impurity in the acid. Bench scale tests have been successfully replicated on a plant scale leading to a better understanding of the composition of impurity levels within phosphoric acid required to produce a high quality, free flowing, hard, spherical and non-caking granular fertilizer.

Jan 1, 2002

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019

By I. Cifuentes

Chemical and physical characterization of copper electrodeposits obtained on mesh and plate cathodes in conventional and reactive electrodialysis lab-scale cells have been carried out. The effect of Fe, Mn, Cl and guar on electrodeposit composition and morphology were determined by means of metallographies, scanning electron microscopy (SEM), atomic force microscopy (AFM), inductively coupled plasma mass spectrometry (ICP-MS) and Auger electron spectroscopy (AES). Each impurity influenced the deposit morphology in a different way (e. g. grain size, surface roughness). AFM proved to be a very effective tool for quantifiying and classifiying surface quality.

Jan 1, 2007

By Lawrence Addicks

ONE of the properties of copper, which has done much to give it its present prominent place among the useful metals, is its electrical conductivity, a property which has now become the chief criterion of 'the value of the commerical product. In pursuance of that distinctively American principle that, 1' the best is none too good," metal of the highest conductivity is usually called for even where such extreme purity is of no advantage, for instance, in the making of brass and other alloys. The average brass-founder feels nervous unless his copper is so very pure that it shows a conductivity of 99 or 100 per cent., while the character of the zinc used is usually overlooked in his anxiety. Electrolytic refining has made it possible to produce copper of a' very high degree of purity, the metallic impurities averaging but a few thousandths of 1 per cent.; oxygen, usually present in the form of cuprous oxide, bringing the total up to about a tenth of 1 per cent. The published data bearing upon the relationship between chemical purity and electrical conductivity is, however, very scant,' nearly all the work that has been done having dealt with alloys carrying considerable quantities of the foreign elements. In this paper I have brought together the results of experiments extending over a period of several years that have been carried out with the idea of determining the amount of various elements which would lower the conductivity 3 or 4 per cent.-a series of impure coppers rather than alloys. There are many precautions necessary to keep the conditions

Mar 1, 1905

By H. E. Brauer

PART I INTRODUCTION Among the zinc base alloys used for casting in metal moulds, particularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortness which facilitate casting. Objection to the use of these alloys may bee raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intercrystalline corrosion. In all cases which have come to our knowledge where the conditions of service were known, failure has occurred upon exposure to moisture and heat varying from a hot moist atmosphere to high pressure steam. Moreover, the alloys described in all such cases contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intercrystalline oxidation in zinc-aluminum alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Bauer2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the most part, and Rawdon's3 examinations were made on an alloy containing 0.4 per cent. lead also exposed to the Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to determine the exact nature of this phenomenon and the effect of other metals present as impurities or intentional additions in accelerating or-retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation.

Jan 8, 1922

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By P. Stantke

Glue, thiourea and chloride are the common reagents which are used in copper electrorefining to achieve fine-grained and smooth copper deposition. While thiourea and chloride are clearly defined chemical substances, glue is a natural product consisting of a mixture of amino acids in different constituent parts. The amino acids are continually degraded in the electrolyte by hydrolysis until they finally become completely inactive. This effect is well-known, largely constant and balanced by the continuous dosing of glue. In contrast, the behaviour of glue in the batch container is not always foreseeable. The glue can become partly or completely inactive by contamination with acid or bacteria, for instance. Usually this is not noticed, and partly or fully inactive glue is added to the electrolyte over a longish period, with the result that the copper growth is significantly impaired. Examples from operational practice show that, with the help of the CollaMat system, partly or fully inactive glue batches can be quickly detected.

Jan 1, 2007

By D Schneider, H Elliott

The advantages and disadvantages of using inclined boreholes in blasting has been under discussion for a long time. Some recognized disadvantages are that drilling costs, both operating and capital costs, are higher for inclined holes than for vertical ones, and that drilling accuracy is more difficult to maintain. People who have used angled holes in practice, on the other hand, have claimed that the quality of blast results was improved. In fact, their popularity has increased, especially in Australia.

Jan 1, 1988

By Walter Nelson

Considerable thought and discussion had been devoted toward provision for increased milling capacity at the Allenby concentrator of The Granby Consolidated Mining, Smelting and Power Company operations as early as 1940. During the war, plans for the installation of an additional grindi.ng unit were formulated but were not carried out. It took considerable time after the war to prepare the mine again for its highest rate of production since, with the scarcity of men, development work had been sacrificed in favour of maximum ore shipments. In order to prepare for the expected competitive market in copper, the matter of increasing the capacity of the concentrator was again given serious attention. As ore became available in the mine and the output of the mill was increased, limitations for a satisfactory recovery were observed, due to the overloaded condition of the classifier units at the higher tonnages. From a metallurgical standpoint, the ore from the Copper Mountain mine had always been difficult to treat on account of the finely disseminated character of much of the mineralization and the difficulty of grinding to the desired fineness. This trouble has become aggravated with time as an increasing amount of wall-rock has diluted the ore and lower grade orebodies have been mined. It therefore has been, and is, the practice at the concentrator to maintain the maximum amount of reduction in size of material fed to the flotation units as is possible for the daily tonnage to be milled. This means that all the grinding units are operated for the maximum possible time, and that the classifiers are regulated to return as much feed ?as possible to the mills. The number of tons to be milled for ?the day is determined by the concentrator superintendent after ascertaining the availability of ore from the mine, the condition of the concentrator ore bins, and the need for repairs in the rolls plant. In order to maintain the tonnage des1red, hourly estimates are made of the rate of grinding by weighing the amount of ore contained on one foot of each of the belts conveying the feed to the various ball-mills, and adjustments are made accordingly.

Jan 1, 1950

IT has often been stated in the past that the materials known as inert fillers were merely adulterants nsed in the manufacture of paint, and that their purpose was to cheapen paints made from more expensive pigments, such as zinc oxide or white lead. In recent years, however, practical tests in various parts of the world have proved that many of the inert fillers, when used with wisdom, possess very definite and advantageous properties.Another oft-repeated statement which had a far-reaching effect in the past, and which is not without influence to-day, is that the very best paint must always be made from a pure pigment, without admixture with either a fellow pigment or an inert filler. Both or either of these statements may be true in a few isolated instances, but for the vast majority of ordinary painting conditions there is an abundance of experimental evidence to prove that neither is true.With the desire to further investigate these points and po 'determine the best combination of pigments and fillers for use as an outside white paint on plant buildings, a number of panels were prepared in the laboratory of this company.

Jan 1, 1924

By T. S. Spicer

Inflammability and crossing point apparatuses were used to study the influence of increasing amounts of such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition.

Jan 1, 1962

By Herbert D. Drechsler, James B. Stephenson

"AbstractThe paper identifies the major components of price change which affect the determination of the internal rate of return of a mining project. It illustrates several price indexes which may be used to measure general price increases, identifying techniques which might incorporate them into mine valuation procedures. The ""hurdle rate"" for new investment is discussed.IntroductionDECISIONS regarding the value of an orebody and whether or when to mine an orebody are based on an estimate of the cash flows which would be associated with its exploitation. These pro-forma cash flows represent cash in or out of a possible mineable deposit and include exploration and construction costs, sales revenues, operating expenses, taxes, debt borrowings, interest and debt repayment. It has long been recognized that when combining the cash flows occurring over the life of the mine, dollars received or paid out early have greater value than those received or paid out later. This time value of money has been incorporated into mine evaluation calculations through the use of present-value or discounting techniques. Another factor affecting mine valuation, inflation, is not accounted for by valuation techniques now in use. In recent years, price changes have become more volatile. In the past, price change could easily be ignored when evaluating potential mines. Today, the combination of larger investments and greater price volatility leads to great concern about the effects of price change on mine valuation."

Jan 1, 1977

By Salehi M. R

Although inherent mineral matter appears to have no effect of the reflectivity of inertinite in the reflecting light microscope, it has a marked effect on the grey levels resulting from the backscattered electron response in the scanning electron microscope. Inertinite with a high inherent mineral matter content has a high grey level response but not as high as that of mineral matter. The highest grey level response is with inertodetrinite which at times could be mistaken for mineral matter. Fusinite has a higher grey level response than semi-fusinite. The backscattered electron grey level response corresponds to average atomic number and hence approximately to density. If a porous structure develops and becomes filled with mineral matter such as S, Cl, Ca, Si, and Al the grey level will be higher. Micrinite has an unusual response in that it behaves like an exinite maceral in the SEM rather than an inertinite maceral. It either has a low grey level when relatively free of inherent mineral matter, or a low grey level background with high level granules corresponding to Si and Al dominantly. Similar structures have been found in exsudatinite and resinite. It is thought that micrinite results from the migration of hydrocarbons out of exinite giving a porous structure which usually accommodates inorganic matter.

Jan 1, 1991