Search Documents

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979

By J. D. Miller, M. Misra

The processing strategy for the effective separation of bitumen from low grade (<l0 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However, the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1981

By Y. M. Zhao

The separating performance of a pilot dry beneficiation system using a gas-solid fluidized bed was investigated with coal from South Africa. The coal used for the study has a low inherent moisture content, a moderate ash content, a moderate volatile content, a low sulphur content and a high calorific value. Its washability is moderate. Experimental results show that the separating quality of the fluidized bed drops gradually as the feed-coal particle size decreases. The probable error, E, values for 50?25mm, 25?13 mm and 13?6 mm coals were 0.04 g/cm3, 0.06 g/cm3 and 0.09 g/cm3, respectively. The cause of the differences in separating characteristics was analysed by particle dynamics and numerical modelling. Furthermore, the pilot fluidized bed was employed to separate 50-6mm coal. In this experiment the coal ash content was reduced from 23.74% to 11.79%, with a probable error, E, value of 0.07 g/cm3and a recovery efficiency of 98.26%. This indicates that the fluidized bed is applicable to the separation of coal from South Africa and has good separating performance and wide applicability. Keywords: feed-coal particle size; gas-solid fluidized bed; dry coal beneficiation; numerical simulation.

Jan 1, 2010

By R A. Anand, N N. Viswanathan, M M. Pande

Slags are the most voluminous solid by-products generated in pyrometallurgical operations, and, as such, finding an application for these oxidic materials is pertinent to maintaining resource efficiency. In particular, pyrometallurgical copper production is associated with high slag rates, typically ranging from 2.2 to 3.0 tons of slag per ton produced copper, which necessitates slag valourisation. A possible application for these iron silicate slags is as supplementary cementitious materials (SCMs), which effectively lowers the CO2 emissions per ton of cementitious material. Although utilising iron silicate slags as SCMs has been studied in previous work, the scientific literature has limited data on the effect of composition on the inherent reactivity in cementitious systems. More specifically, no reports on the impact of FeO/SiO2 ratio have been presented in previous publications. Therefore, the present study aimed to isolate this parameter in a synthetic FeO-SiO2-Al2O3-CaO-MgO-Cr2O3 system. Since the amorphous content is a pertinent parameter for SCMs, a high-temperature confocal laser scanning microscope (HT-CLSM) was utilised to assess the crystallisation behaviour at continuous cooling conditions. Furthermore, high-temperature rheological experiments were conducted to measure the viscosities of the slags in relation to the crystallisation behaviour. The experiments showed that depolymerising the slag by increasing the FeO/SiO2 ratio generated a less viscous slag, which showed higher tendencies for crystallisation. Furthermore, experiments assessing the inherent reactivity as an SCM showed that depolymerising the slag by increasing the FeO/SiO2 ratio as the sole independent parameter generated an initially more reactive slag. However, replacing SiO2 with FeO was found to negatively affect the reactivity as measured over seven days within the tested compositional range.

Jun 19, 2024

By Ken Rahal, Chris Braun

As head grades of mines around the world decline, generation of tailings is increasing. Along with the increased tailings generation, reduction in water availability, and recent tailings dame failures, are causing mining companies to look at different disposal methods. One of the methods that is gaining traction is filtered tailings. Filtered Tailings currently provides the greatest water recovery and the smallest footprint among all the tailings disposal methods. This paper will present two case studies that analyze the filter and air compressor costs associated with a change in the final cake moisture target (i.e. a change from 17-wt% to 15-wt% cake moisture), for a base metal mine and gold mine.

Sep 30, 2022

By C. B. Webber, W. A. Grell

"Sherritt Gordon's Ruttan Mine is a copper-zinc operation located approximately 600 miles north-west of Winnipeg. Open pit mining began in 1973 at 10,000 Tpd., with a change over to underground mining in 1981 producing 7,500 Tpd. Ore is crushed to -3/4"" followed by rod and ball mill grinding (two ball mills in series), differential copper-zinc flotation, and dewatering. The copper and zinc concentrates are trucked 75 miles to Lynn Lake, where they are shipped by rail to the HBM&S smelter at Flin Flon.This paper describes a method used to predict the effect of grind particle size on metallurgical performance, as well as details on the copper and zinc metallurgical performance due to fine grinding in actual plant operation.Initial statistical studies on historical data (including ore source, head gr3de, grind, etc.) indicated that copper and zinc recoveries increased with fineness of grind, in the range of 50 to 65% -200 mesh.In order to extrapolate beyond 65% -200 mesh, and to develop expected nonlinear relations between grind, Cu concentrate grade, and recovery, the assays of screen fractions of copper concentrate and tailing were used to determin8 the relation between net smelter return (a function of grade and recovery) and grinding cost. The optimum economic grind would be that grind at which the net smelter return less grinding cost reached a maximum."

Jan 1, 1982

By Douglas W. Reeve, Hoc Nghia Tran, David Barham

"In kraft pulp mills, the spent pulping liquor is concentrated and used as fuel in the recovery boiler. Extensive deposits are formed in the upper section of the boiler due to the very high ash content of the fuel and the volatite nature of the ash. Deposits are composed of Na2S04, Na2C03 NaCI, some potassium salts and reduced sulphur compounds. Chloride and potassium salts are enriched in the deposits compared to the smelt due to their greater volatility.Severe corrosion of the superheater tubes in a recovery boiler has been traced to three factors: a non-uniform temperature profile in the flue gas, relatively high operating steam temperatures and high chIoride and potassium concentrations in the fireside deposits.The role of chIoride and potassium in superheater corrosion has been explained by increased Iiquid phase in deposits. Together with corrosion studies, this information has shown that kraft recovery boiler superheater corrosion due to the chloride and potassium enriched deposits can be avoided by proper boiler operation and by judicious superheater and furnace design.IntroductionThis investigation of recovery boiler superheater corrosion was initiated by the discovery of severe corrosion of the final stage superheater in a Canadian closed cycle kraft pulp mill(1,2). Metal wastage leading to tube failure was believed to be due to three major causes : the relatively high operating steam temperatures, the uneven distribution of flue gas temperature across the boiler which created a "" hot spot"" and the high chloride and potassium concentrations in the superheater fire side deposit. The mill responded to the problem by i) lowering the superheater steam temperature from 475°C to 380°C, ii) minimizing the chloride content in the spent pulping liquor, by controlling the NaCI input with recovered bleach plant effluent, and iii) changing metallurgy of a portion of the bottom section of the final stage superheater platens from ferritic steel T-22 (2.25% Cr, 1% Mo) to austenitic steel Incoloy 800H (21% Cr, 32% Ni, 46% Fe, 1.5% Mn, 1% Si, 0.6% Al) (Fig. 1). Details of the superheater corrosion experienced in the closed cycle mil! have been reported in previous papers(l ·2,) ."

Jan 1, 1984

By Douglas A. Sloan

AN INCENTIVE or bonus system of payment is commonly used for mine labour. The incentive rates are usually based on the variable units of production, such as dollars per foot of drift advance or cents per ton of ore broken. Portions of the work that must be done to achieve the units of ?production are independent of the production unit and tend to be fixed work for the shift or for the job, irrespective of the production achieved. This fixed work has considerable influence on the equity of incentive rates. The effect of fixed work is to accelerate the loosening or tightening of rates if the production task is over-achieved or under-achieved, and of increasing the loosening of rates loosely set and the tightening of rates tightly set. This gearing of mine contract rates is the reason why changes in conditions, materials, equipment, or methods will change the incentive earnings to a greater degree than would normally be expected. Obviously, therefore, care should be taken in the setting of the task for incentive rates as the gearing makes an inequitable rate even more inequitable.

Jan 1, 1958

By Donald P. Spitzer, Peter V. Avotins

The flow properties of thickener underflow slurries can be characterized by their rheological parameters. Most of these slurries exhibit Bingham plastic behavior, characterized by a yield stress, to, and a Bingham viscosity, nB. Red mud is generated as a leach residue in the Bayer process. The use of new Bayer process flocculants which contain hydroxamate functional groups leads to muds which are qua1itatively considerably more fluid than muds generated with conventional polyacrylates or acrylatefamide copolymers. A variety of rheological tests confirm lower yield stresses and less extended floc structures with the new flocculants, at the same solids levels. Conversely, under given viscosity restraints, the new polymers make it possible to operate at higher solids levels, which offers major benefits in processing red muds.

Jan 1, 1992

By Sparrow G. J

The effect of polyelectrolyte flocculants on the de-watering of a tailing suspension of very fine clay was investigated.Sedimentation and filtration experiments were carried out in the labqratory to characterise the de-watering properties of the tailing. The results were used to calculate the effect of flocculant additions on the drainage and vaporation components of the de-watering of a clay suspension ponded on to a sand drainage bed.A flocculant increased the drainage rate, but decreased the volume of water that could be removed by drainage leaving more water to be lost by evaporation.The sorptivity values measured in the laboratory were used in the de-watering equation previously established for the tailing to estimate the effect of flocculant additions on the time required to de-water the suspension from 18.2 to 60 per cent solids w/w. The calculated de-watering times were found to increase or decrease depending on the volume of water removed by drainage and the prevailing evaporation rate.

Jan 1, 1980

By Mohammad Mehdi Salarirad

Fouling of activated carbon by different organic species is a great concern in carbon in pulp and carbon in leach circuits. The rate of gold adsorption onto activated carbon from synthetic gold solutions which contained different amounts of potassium ethyl xanthate (PEX), potassium isobutyl xanthate (PIBX), and methyl isobutyl carbinol (MIBC) were evaluated through batch adsorption tests. The results of these experiments showed that the gold sorption rate rapidly decreases by increasing the concentration of collectors including PIBX and PEX up to 20 mg/L and at higher concentrations, the kinetic rate constant (i.e., k value) gradually leveled off to 53 h-1 for PIBX, which is 46% lower than the 99 h-1 for PEX. At low concentrations of up to 15 mg/L of MIBC, a gradual decrease of the rate constant was observed, while at higher concentrations, the decrease was found to be more pronounced. The gold loading capacity and the rate of gold adsorption onto activated carbon from a gold cyanidation pulp in the presence of flotation reagents were also evaluated. The results of these experiments showed that the flotation reagents have no significant effect on the gold loading capacity of activated carbon at prolong adsorption period, meanwhile the rate of gold adsorption continuously decreases by increasing the concentration of flotation reagents in the leaching solution.

Oct 1, 2011

By A. Tsubouchi, F. Noguchi, T. Takasu

"A high current density operation is desired to improve the productivity in copper electrorefining. However, a lot of problems still remain such as passivation at anode, dendritic deposition at cathode and impurity behavior during the electro refining.Effects of the current densitY on the morphology of copper deposition on the cathode, and passivation at the anode were investigated at various fluid velocity of electrolyte in the present study.Although a granular appearance of the copper deposition was obtained with increasing high current density, it was depressed by an increase of the fluid velocity of the electrolyte. A uniform deposition on the cathode was also observed when the fluid velocity of the electrolyte become higher. It was ascertained that passivation at the anode was suppressed by circulating electrolyte during electrolysis. INTRODUCTIONIt is desirable to operate at high current density in copper electrorefining in order to improve plant productivity without enlarging the size of electrodes(1). However, there are many problems in copper electrorefining at high current density with the usual commercial practice, for example, anode passivation, dendritic deposition and an increase of impurities in the cathode.In general, it is effective to agitate the electrolyte in order to suppress these problems(2). Smith et a1.(3) have performed electro refining experiments at various current densities in the range of 8 to 32 Aldm2 and at electrolyte fluid velocities in the range of 40 to 120 mlmin, and they obtained well consolidated, void free copper even at high current density in a high electrolyte velocity. However, they did not discuss the recovery ratio and the passivation behaviour at the anode. Walsh et a1.(4)(5)(6) experimented with the rotating cylinder electrode, and ascertained that electrolysis can be carried out at high current densities under the condition of pure electrolyte.With regards to anode passivation, there are several papers by previous workers(7)(8). Our group ascertained the process of producing anode slime during electrolysis(9). However, these experiments were carried out without forced circulation of electrolyte. Therefore, in the present study, to solve these problems, we electrolyzed at current densities in the range of 4 to 50 Aldm2 with circulating electrolyte in the range of 0 to 48 mlrnin. The effect of electrolyte fluid velocity on the surface morphology of deposited copper at cathode and passivation at anode were investigated when electrolysis were carried out with circulating electrolyte at high fluid velocity and at high current density."

Jan 1, 1997

By M. S. Greenfield, E. Cocchiarella, S. Chubbs

"At Dofasco sNo.4furnace a variation of the basic oxygen steelmaking process, Klockner Oxygen Bottom Maxhutte (K-OBM), is used to produce steel. Large amounts of hot gases and particulate are evolved during the oxygen blowing phase. A quencher and a venturi scrubber are used to collect over 99.5% of the particulate. In 1990, the authors investigated the effect of foamy slag on the particulate emissions from the furnace. The amount of lime added early in the oxygen blowing cycle was reduced, making the slag more viscous and foamy for a six minute period. Instantaneous particulate emissions were monitored throughout the blow by analyzing quencher and venturi scrubber water samples. Particulate emissions were reduced up to 59% during the foamy slag period.IntroductionThe reduction of the amount of waste generated or control of emissions at source is at the top of the ""3R"" hierarchy of waste management (Reduce, Reuse, Recycle). Process and operating practice changes are often the most economical ways to control emissions. At Dofasco, they investigated the effect of operating practice changes, specifically the formation of a foamy slag, on particulate emissions from steelmaking furnaces. They wanted to determine if a foamy slag changed the quantity and nature of the fume evolved from the K-OBM furnace over the oxygen blowing phase.The Basic Oxygen Steelmaking ProcessesThe basic oxygen steelmaking process (BOP) generates large quantities of very fine metal oxide fume during the production of steel. In this process, scrap steel and molten iron (hot metal) from blast furnaces are charged into a steelmaking furnace. Then pure oxygen is injected and a lime flux added . The oxygen reacts with carbon dissolved in the molten iron to form carbon monoxide. Oxygen lances can have secondary nozzles which introduce oxygen above the bath. This secondary oxygen, known as post-combustion, bums some of the carbon monoxide radiating the heat back to the bath. Particulate and gases rich in carbon monoxide are ejected from the furnace during the oxygen blowing phase and are collected by a gas cleaning system. Typically, more than 99.5010 of the particulate is scrubbed from the gases by high energy venturi scrubbers or electrostatic precipitators. The oxide sludge or dust collected may have elevated zinc and lead which is unsuitable for recycle to blast furnaces. Due to the presence of these undesirable elements, treatment and disposal of steelmaking oxide dust is difficult and costly."

Jan 1, 1993

By R. P. Benson, D. H. MacDonald, D. R. McCreath

1 - INTRODUCTION The Canadian Shield is well known as being among the older exposed areas of the earth&apos;s surface. Except for local zones, its extent from the Arctic to central North America is characterized by strong and durable crystalline rocks. It is generally regarded as highly competent for tunnelling and underground excavation and, as a result, many openings are excavated in it with minimal temporary support. If hydraulic efficiency is not a factor, tunnels do not usually require continuous concrete linings. A high percentage of the crystalline rocks of the Shield are of metamorphic origin and as such one of the dominant characteristics is their foliation. Zones of sheared or faulted rock are common in the Canadian Shield, particularly in association with foliation. These zones may be created during the late stages of the metamorphic process, leaving shear zones as an integral feature of foliated rock. As foliation is a preferred direction of weakness, deformation and rupture during subsequent tectonism may also create parallel shear zones. These "foliation shear zones", as described by Deere (1973), are an adverse feature of the otherwise durable rocks of the Canadian Shield. The zones may range from faults of major proportions to seams only a fraction of an inch thick. If fault gouge or alteration products exist in the zone the strength of the rock mass may be great1y reduced. As foliation is usually continuous, large unstable wedges of rock may be created if the opening is subparallel to the foliation. The effect on the construction of underground openings in terms of excavations, support and scheduling can be significant.

Jan 1, 1974

By J. A. Ryder, M. U. Ozbay

An ERR-based methodology is presented for use in the re-assessment of the performance of stabilizing pillars, taking into account the effects of fracturing that can occur in pillar foundations under conditions of high stress. It is shown that the damage in the foundations of under-designed pillars can cause up to 30 per cent increases in ERR compared with the ERR for pillars with unfractured foundations. Despite this reduction in assessed performance, stabilizing pillars are still generally found to result in substantially lower ERR levels than alternative methods of reducing ERR, such as the use of stiff backfill or backfill ribs.

Jan 1, 1990

By Michael D. McGill

The effect of fragmentation size distribution as it relates to front end loader productivity was evaluated by comparing loader cycle times to fragmentation size of the shot rock. At Gold Mine in Southern Utah, a gold deposit containing both limestone and sandstone formations were blasted in the same shot.

Jan 1, 1994

By Michael D. McGill, Jeff Freadrich

There are many factors which affect the productivity of a front end loader. One of the most obvious is the characteristics of the material being mined. Characteristics such as size distribution, swell factor or heave, and material hardness / abrasiveness will all effect the efficiency of the mucking cycle. The focus of this paper is to look specifically at the size distribution of blasted material, and quantify the effects on loader productivity.

Jan 1, 1994

By M. H. Moys, C. Bhondayi, Eric Tshibwabwa

"The relationship between froth bubble size as represented by intra-bubble impact distances (IID) and flotation performance is investigated. Experiments using an artificial ore comprising of limestone as the floatable component and silica as the gangue material were carried out in pseudo-steady-state circuit. A method to measure IIDs developed by Bhondayi and Moys (2014) was then used to measure froth bubble sizes as a function of froth height, superficial gas velocity and feed rate (pulp residence time). Samples for flotation performance evaluation were also taken. Results indicate that as froth height increases, the average IID values increase resulting in a decrease in limestone recovery while the grade increases. Increasing gas rate results in lower IID values that are accompanied by high recovery and low limestone grade. The effect of feed rate on both flotation performance and average IID values depended on froth depth and gas rate. Average IIDs largely remained the same at the two feed rates investigated.INTRODUCTIONIt is regarded as obvious that froth bubble size distribution (FBSD) will have an effect on plant grade and recovery. As the average FBSD decreases, the bubble surface area flux will increase making possible an increase in recovery and a decrease in grade. The opposite trend will be involved if average FBSD is increased. However: no method for measuring FBSD has been available, so these trends have not been studied in any detail. Bhondayi and Moys (2014) developed a novel technique to measure or estimate froth bubble sizes. Although they established a potential to use this method in understanding froth performance, no data have been presented to assess the correlation between the estimates of bubble sizes and actual flotation performance. In this work experiments are done to establish how the change in froth phase bubble sizes affect flotation performance. Flotation performance will be evaluated using recovery and grade. How water recovery to the concentrate changes with changes in bubble sizes will also be evaluated. It is known that water recovery is approximately inversely proportional to the square of the overflowing bubbles sizes. It will be interesting to establish how the rate of change of bubble sizes changes with water recovery."

Jan 1, 2016

By F. G. Miller

To improve coal flotation Bethlehem Steel Corporation&apos;s Research Department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies5 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the bas is for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14M x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level.

Jan 1, 1968