Search Documents

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By J. Jávor

The response of the air/water interfaces to deformation in presence of surfactants is affected by the adsorption/desorption rate, re-orientation and exchange rate of surfactant. These surface properties can be observed using equilibrium and dynamic surface tension and surface elasticity measurements. However, the effect of these parameters on bubble size in dynamic conditions has not been studied due to the difficulty in capturing freshly formed bubbles in dynamic conditions. The paper presents a new experimental set-up designed and built at the Aalto University, called Shear Force Observation Chamber(SOC). The setupallows the monitoring and analysisof freshly formed air/liquid interfaces in dynamic conditions and facilitates the study of the effect of dynamic surface tension and surface elasticityon freshly formed air bubblesin presence of surfactants. The method helps to establish correlation between bubble size and dynamic interfacial properties and bubble-bubble interaction in turbulent flow. Dowfroth 200, Nasfroth 240 and Dowfroth 250 commercial flotation frothers were tested in this study. The results show a marked difference between results obtained in dynamic conditions compared to the static conditions. The results are presented and the reasons and implication to flotation modelling are discussed in the paper. Keywords: shear force observation chamber, flotation frothers, flotation bubbles, critical coalescence concentration

Sep 1, 2012

By T. A. Muhlare

The use of electrolyte additives to smoothen cathode deposits during copper deposition is practised worldwide. These additives absorb on the cathode surface and take part in the electrochemical crystallization process. However, these additives also affect the quality of the cathodes when they are inadequately controlled. Electrolyte additives used by Palabora are glue, thiourea, Avitone and chloride. Their effects were determined on cathode quality, the size of the current density region that gives the desired compact morphology, and current efficiency. This was done in a small-scale cell. Small cells have different hydrodynamics from industrial-scale cells, which makes it difficult to simulate the operation of industrial cells in a laboratory. The approach used here was to use a rotating cylinder cathode to attain controlled hydrodynamics. The rotation speed was chosen to give a diffusion layer thickness that is similar to that of an industrial-scale cell. It was shown that even fairly small changes in the additive levels can significantly affect the cathode morphology, and the current density range over which this morphology can be obtained. Keywords Copper, electrorefining, glue, thiourea, avitone and chloride.

Jan 1, 2011

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By Alain Jardy, Thibaut Quatravaux, Denis Ablitzer

"A numerical model of the Vacuum Arc Remelting process has been developed and applied to simulate remelting of various metallic materials, such as specialty steels, titanium and zirconium alloys. In practice, electromagnetic stirring is sometimes used, resulting in a complex 3D molten metal flow. After having validated the numerical model for different remelting conditions, we can use it to study the effect of applying a constant or alternated magnetic field on the thermohydrodynamic behaviour of the melt pool. The intensity of flow turbulence, computed with a classical k-E model, is shown to depend strongly on the nature of electromagnetic stirring.IntroductionThe principle of the Vacuum Arc Remelting (VAR) process, illustrated in figure I, consists in melting a consumable metallic electrode of the required grade under a high vacuum, in order to obtain a sound ingot of good structural quality.During remelting, an electric arc is maintained between the tip of the electrode and the top of the secondary ingot, in order to ensure melting of the electrode. The metal droplets fall through the arc plasma and progressively buid up the ingot, which solidifies in contact with the walls of a water-cooled copper crucible. The secondary ingot formed in this way contains three distinct zones, corresponding to the liquid pool, fully solidified metal and intermediate mushy zone. In order to stabilize the arc, it can be confined with the aid of a magnetic field created by an external induction coil. This field can also be used to stir the liquid metal, the rotation induced being in the orthoradial direction. By reversing periodically the coil current, stirring can be alternated."

Jan 1, 2004

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By I Zh Bunin, V A. Chanturia, V G. Minenko, M V. Ryazantseva, A L. Samusev

A promising source for the extraction of rare metals and REEs in Russia is the eudialyte ores of the Lovozero deposit, which do not contain active uranium components. The eudialyte ore reserves of the Lovozero Massif are considered virtually unlimited and therefore have the potential to become a primary source of a number of rare and rare earth metals. The goal of this study was to comprehensively examine the effect of the parameters of high-power nanosecond electromagnetic pulses (HPEMP) and dielectric barrier discharge (DBD) on the leaching performance of eudialyte concentrate and the selective separation of zirconium and REEs from productive solutions. Using scanning electron microscopy and infrared spectroscopy, the mechanism behind the intensification of acidic dissolution of eudialyte as a result of pretreatment with energy impacts was described. During the HPEMP treatment, weakening and destruction of the eudialyte surface was observed, which at the substructural level is expressed in the deformation and local destruction of Si10O27, Si9MO30 resulting in formation of microcracks. During the DBD treatment, the formation of characteristic defects was observed in the form of imprints of dielectric breakdown microchannels and individual mineral fragments. Pretreatment of eudialyte concentrate using HPEMP made it possible to increase the recovery of zirconium into the pregnant solution of leaching by 3.4–4.3 per cent (from 86.6 per cent to 90.9 per cent) and by 4.1 per cent (from 86.6 per cent to 90.6 per cent) when using DBD. The increase in the total recovery of REEs was 1.2–1.8 per cent (from 87.7 per cent to 89.2 per cent). The effect of pH values, solution temperature, initial concentrations of valuable components on the successive recovery performance of zirconium and REEs from the pregnant solutions nitric from the acid leaching of eudialyte concentrate by chemical precipitation was examined. The possibility of selective separation of the zirconium product and rare earth elements with a zirconium recovery of 99.95 per cent and a REE recovery of 87.5 per cent was established. REE loss with the zirconium product was 8.0 per cent and 4.5 per cent with the spent pregnant solution.

Aug 24, 2022

By David Deglon, Martin Harris, Mehdi Safari

This paper investigates the effect of energy input on the flotation of galena in a novel oscillating grid flotation cell (OGC). Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Previous work was limited to quartz (-100 µm). Galena (-150 µm) was floated in the OGC at power intensities from 0.5 to 3 W/kg using 0.13, 0.58 and 0.82 mm mean bubble sizes (d10) and at three collector dosages. Results show that the effect of power intensity on flotation kinetics is strongly dependent on both particle and bubble size. For fine particles (-19 µm), increasing energy input increases the flotation rate at a low collector dosage but leads to an optimum at both the moderate and high collector dosages. For intermediate particles (+19-38 µm), increasing energy input has no effect on the flotation rate at the low collector dosage but leads to an optimum at both moderate and high collector dosages. For coarse particles (+38-150 µm), increasing energy input has no effect on the flotation rate at the low collector dosage and leads to a general decrease at both moderate and high collector dosages. Optimum conditions for fine particles are using small bubbles at a moderate collector dosage and an energy input of around 2 W/kg. Optimum conditions for moderate particles are using small bubbles at a high collector dosage and energy inputs of around 1.0 W/kg. Coarse particles do not benefit from agitation.

Jan 1, 2014

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By S. K. Utimurd, D. C. R. Espinosa, J. A. S. Tenório

"Waste Electrical and Electronic Equipment (WEEE) has become an environmental issue due to technological advance and waste plastic is one of the main polluters. The excessive discard of these plastics result in a difficult to dispose it to landfill and need further separation with technique in order to produce high added value plastics. There are many kinds of plastics in extensive use at the present time and the co=on are the acrylonitrile-butadiene-styrene (ABS) and high impact polystyrene (HIPS) used in the production of electric appliances. These plastics are difficult to separate because they have similar densities. Flotation of plastics is one possible separation technique and using selective wetting agents. The separation may be possible given close control at particle size and the concentration of the reagent. The process was able to produce a concentrate of HIPS with at least of 93% purity and a concentrate of ABS with 99% purity.IntroductionThe current situation of municipal solid waste (MSW) management especially in emerging economies like Brazil, the growing population and economic activity will result in a significant increase in the generation of waste in the coming decades. It is worthwhile to review and update the sources, amounts and recovery technologies of specific materials from waste, particularly from municipal solid waste (MSW).The growing impact of the current waste management practices stresses the need for a change in how waste is handled. The 2012 survey and the Brazilian Association of Public Cleaning and Special Waste Disposal Companies (ABRELPE) reports the generation of 62 Mt urban MSW in that year, which is an increase of 13% compared to 2011. It has been reported that in Brazil about 90.17% of the generated MSW is currently collected, which indicates an increase in the coverage of collection services compared to 2011 [ l]."

Jan 1, 2014

By Majid Sadeghi, Ali Naghi Dehghan, Kaveh Ahangari, Seyed Mahdi Pourhashemi

"Instrumentation and monitoring of ground deformations in tunneling is a principal means for selecting and controlling the excavation and support methods among those foreseen in the design, for ensuring safety during tunnel construction (including personnel safety inside the tunnel and safety of structures located at ground surface) and, finally, for ensuring construction quality management. In this paper, the effect of Hakim Tunnel excavation on the behavior of the surrounding ground was investigated based on the geotechnical instrumentation. This tunnel with 1080 m length, 18 m width and 12.6 m height is being constructed using the SEM/NATM along the Hakim Highway in Tehran. The results which are obtained from recorded displacements by geodetic pins (on the tunnel wall and roof), extensometers and settlements pins (at the ground surface) demonstrate the tunnel stability during the various stages of excavation. However, it is concluded that the rate of excavation in different sequences could have a major role on stability of tunnel. In this case the surface and underground openings were monitored as well as needed for controlling the face probably collapse. INTRODUCTION Tunneling is increasingly being used world-wide to provide the infrastructure required for sustainable urban areas. The high demand for space and the disturbance of existing infrastructures by construction measures increasingly forces future infrastructure projects to be conducted underground. One of the important purposes of tunneling projects in urban area is not only to minimize displacements but also to control them during the construction (Pourhashemi et al., 2015). Normal method of tunnel stability analysis is not able to evaluate the real rock and soil mass behavior. Hence, instrumentation is a practical method to monitor displacements, to evaluate the stability of underground openings, and also to determine the rock and soil mass properties (Dehghan et al., 2012. Dehghan, 2013). Rocks and soils are materials with properties that can change instantly and significantly from one point to the next. Some complications may often happen due to uncertainties in the loads that the new facility must withstand during construction and operation. Instrumentation and monitoring provide quantitative information on actual behavior of ground and adjacent structures. A lot of deformation monitoring studies for determining and analyzing different kinds of engineering structures such as tunnels, bridges, high-rise buildings and dams are implemented. Considering the type of the structure, its environmental"

Jan 1, 2016

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines fired seven test blasts in a 22-ft bench of limestone, screening the material to investigate the influence of explosive type and between row delays on fragmentation. Four 4-hole, single-row test shots were conducted evaluating dynamite, ANFO, emulsion, and a 60-40 emulsion-ANFO mix. Three 12-hole shots, with three rows of 4-holes, evaluated delays between rows of 24, 36, and 120 ms. Accurate in-hole electronic delays were used, firing within 1.5-ms of the nominal delay. All seven shots had a 6- to 7-ft burden, 10-ft spacing, with a hole diameter of 3-1/2 in fired on a 12-ms delay between holes in the row. The tests were instrumented with strain gauges grouted in the burden region examining stress wave and gas pressure effects. Fiber optic probes were used to confirm timing and to obtain detonation velocities.

Jan 1, 1989

By Nicholas J. Welham

"The effect of extended ball milling has been studied for two industrial processes: (1) the processing of metal sulphide concentrates; and (2) the carbothermic reduction of ilmenite to synthetic rutile. The plant concentrates were a gold ore with 128 g/t Au of which 8% was non-refractory and a zinc concentrate with copper impurities.The gold concentrate showed complete dissolution of the gold bearing minerals after milling giving almost complete gold liberation. The zinc concentrate showed almost all of the sulphides had solubilized leaving the gangue and elemental sulphur. A study of pure pyrite and arsenopyrite shows that selective dissolution should be possible by a simple leaching process directly after milling.The milling of ilmenite and coal together results in a temperature decrease of 150°C in the subsequent carbothermic reduction of ilmenite, in addition to improving both the rate of reaction and the selectivity of reduction to rutile. IntroductionAlmost all mineral processing plants use mills for the size reduction of particles prior to physical and chemical processing. When continuing beyond size reduction the energy transferred causes deformation, breakage and realloying of particles giving a steady-state particle size. The breaking also causes increasing damage to the crystal structure by formation of smaller grains giving an increasing number of grain boundaries and increasing crystalline defects due to deformation. The increasing number of grain boundaries and defects leads to increased reactivity, which can be seen directly by a reaction within the mill, or indirectly, via a decrease in the subsequent annealing temperature required for reaction."

Jan 1, 1997

By D. C. R. Espinosa, P. Aliprandini, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel and cobalt are the main value metals in nickel laterite ore. Cyanex 272 is an extractant used to separate nickel from cobalt present in leach solutions. Previous studies demonstrated the extraction of cobalt, magnesium and manganese at pH 5 using Cyanex 272 as extractant, while nickel remained in aqueous solution. However, it is difficult to separate cobalt from a solution containing magnesium and manganese. One possibility to change the metals’ behavior during the solvent extraction process is to change the mixture of extractants used. In order to study the solvent extraction of cobalt from a solution containing manganese, magnesium and nickel, a mixture of two extractants was investigated. Cyanex 272 (CY) and Versatic 10 (VC) were selected as extractants in the organic phase. The extractant concentrations used were: 20% CY; 15% CY, 5% VC; 10% CY, 10% VC; 5% CY, 15% VC; and 20% VC. In all cases, kerosene was used as a diluent, at 80 vol%. The synthetic leach solution used in this study was prepared according to the composition of a typical nickel laterite leach solution. The pH value of the solution used was 5, and the aqueous/organic ratio used in solvent extraction testwork was 1/1. The study has shown that the composition of the organic extractant mixture did not increase cobalt separation.INTRODUCTION Sulfide and laterite deposits are the main sources of nickel. However, production from nickel sulfide ores has been decreasing over the years, relatively speaking, increasing the focus on the exploitation of laterite nickel ores (McDonald & Whittington, 2008). Laterite ore deposits are found in tropical and subtropical regions. A characteristic of laterite ores is the presence of a complex and heterogeneous mixture of metals (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011; Georgiou & Papangelakis, 1998; Gupta, 2003; Kesler & Simon, 2015; Moskalyk & Alfantazi, 2002; Oliveira, 1990). Nickel concentrations in laterite ores are typically 1–2% (Dalvi, Bacon, & Osborne, 2004)."

Jan 1, 2017

By James M. Fragomeni

"The mechanical behavior of an Al-Li alloy was studied and related to the extrusion processing parameters, the plastic metal flow during defonnation, the anisotropy, and the microstructure. The extrusion temperatures, strain rates, extrusion ratios, billet temperatures, and extrusion geometries were varied during processing and correlated with the microstructure and properties. The extrusion processing variables were related to the mechariicar behavior, anisotropy, and microstructure through the ZenerHollomon parameter i.e., the temperature compensated strain rate. Based on optical and electron microscopy studies it was found that regardless of the extrusion conditions, the various microstructures for the most part were unrecrystallized for both the as-extruded and the solution heat-treated conditions. Smaller grain sizes were correlated to larger Zener-Hollomon parameters. The extrusion temperature and ratio did not significantly affect the strength or ductility as did the section geometry, which had a large affect on these mechanical properties. The anisotropy of the properties varied substantially when comparing the extruded longitudinal versus transverse grain orientations.IntroductionThe extrusion process also has a substantial influence on: the microsfructure and mechanical properties of a material that is Athens, Ohio, 45701 fonned The plastic defonnation that occurs during the extrusion process alters the grain size, crystallographic texture, anisotropy, subgrain size, dislocation density and various other microstructural features. Often the material being extruded is not homogeneous, therefore variations in the microstructure and properties occur across the cross-section of the final extruded product. The mechanical properties and microstructure can also vary with length since it is hard to maintain a constant temperature throughout the extrusion process. The extrusion temperature often varies from the heat generated during the extrusion process. The demonstration material that was extruded for this .study was an aluminum alloy containing 2.6wt, % lithium and 0.09wt.% zirconium. This alloy was strengthened by heat treatment causing nucleation, growth, and coarsening of coherent metastable o' (Al3Li) precipitates in the microstructure. The ? precipitates which are a consequence 9f artificially aging the AlLi alloy, are spherical, ordered, and coherent with the aluminum matrix and impede the dislocation glide inotion during plastic defonnation. Theo particles grow homogeneously in the matrix, and have the Cu3Au (L 12)"" superlattice crystal structure. Aluminum-lithium alloys are used primarily for aerospace structural applications since they have attractive properties such as a lower density and higher elastic modulus than conventional 2XXX and 7XXX alloys."

Jan 1, 2000

By Keith G. Wallace

The effect of face resistance on ventilation air leakage through stoppings was measured in a twin development heading. Face resistance was varied by alternately tightening or loosening the face line brattice to change the line brattice leakage. Results indicated that tight brattice lines are necessary to maintain acceptable airflow at the face but result in higher leakage throughout the entire system, reduced overall ventilation efficiency, and higher operating costs. Conversely, a low face resistance which simulated an auxiliary fan/duct system gave reduced stopping leakage losses, higher quantities of air at the last open cross-cut and greater entire system efficiencies

Jan 1, 1984

By Enver Alan, MerkeziYapı

People are migrating because of economic, social, natural and political reasons. These natural and humane factors effects the distribution of populations. The need for tunnels has grown in order to provide a comfortable life and reduce losses such as waste of time, labor, energy, efficiency and so on. It is inevitable to carry out excavations in rock tunnels (shears, platforms, lines, connections, wastewater, distribution, energy, transportation etc.), that will be built by excavating with conventional method, by controlled blasting regarding with constrains. In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. Six microphones were used to measure the air shock and eight geophones were used to measure the parameter values of the vibrations (particle velocity, frequency, displacement, acceleration, amplitude, wavelength etc.), which were placed at predetermined points of the surface, occurred during the blasting applications. Data from the geophone and microphones were recorded on six seismographs. The coordinates and the distances between the shot points and the measurement stations are determined by an electronic theodolite. The total number of seismic records, recorded in seismographs, is 118. The number of records of vibrations that crossed the faults is 42 and the number of records of vibrations that did not cross the fault is 76. The particle velocity, frequency, amplitude, acceleration, displacement and wavelength were measured in transverse, longitudinal and vertical directions. The total number of measurements is 354. By evaluating all seismic records, the effect of delay intervals, faults and scaled distances on the particle velocity, frequency, amplitude, displacement, acceleration, wavelength and air shock were investigated. When the vibrations formed during the Research & Development (R&D) blasts were examined, it was determined that the parameter values of vibrations that crossed the faults are lower than the ones that did not cross the faults. In addition, when the particle velocity values of all vibrations are examined according to the present circumstances, it is determined that the waves did not cross the fault in all delay intervals are superposed in all directions, and that the least superposing occurred in the 50 ms delay range.

By Enver Alan

In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. S

Feb 1, 2020

By Takeshi Yoshikawa, Kazuki Morita, Yuichi Kato

"A composite composed of carbon fiber and a Cu-Si alloy is a promising candidate for next generation brake disc materials used in high-speed trains. The composite can be prepared by vacuum infiltration of the Cu-Si alloy into the fibrous carbon matrix. The activity of Si in the alloy plays an important role in controlling the formation of SiC; this formation is attributed to the reaction between the Si in the alloy and the carbon fiber during the infiltration process. Because Fe has strong affinity with Si, the addition of Fe is expected to decrease the activity of Si in the alloy. In the present work, the variation in the activity of Si in the alloy with the addition of Fe has been investigated by equilibrating a Cu-Fe-Si alloy with solid SiO2 and graphite under controlled CO partial pressure. The first-order and second-order interaction parameter of Fe on Si in molten Cu was determined to be -16 and 160, respectively. The negative value of the first-order interaction parameter clarified the addition of Fe to the Cu-Si alloy is effective in decreasing the activity of Si in the alloy.IntroductionIron-based materials have been commonly used for brake discs in high-speed trains. It becomes critical for brake disc materials to withstand high thermal loads with an increase in the maximum speed of high-speed trains. The fabrication of high heat-resistant, light-weight brake disc materials is then crucial for their use in next-generation high-speed trains. Carbon fiber is known to be a light-weight, high-strength material, and is considered to be a promising matrix material for use in brake discs. The Cu-Si alloy exhibits high thermal conductivity. The composite in which the Cu-Si alloy is added to the carbon fiber matrix is expected to be a high performance material for brake discs. The composite can be prepared by the infiltration of the Cu-Si alloy into the carbon fiber matrix at a temperature higher than 1700 K."

Jan 1, 2012

By H. Bradley Johnson

A number of Federal laws affecting safety and health in the mining industry has been enacted and revised over a period of many years. We have tended to classify these laws and their applicability into three categories: 1) coal mines, 2) metal and nonmetallic mines, and 3) mines with Federal supply contracts. With the growing attention which is being given to mine safety by the Federal government, the entire mining industry should keep aware of all developments in the administration of each of these laws.

Jan 1, 1970