Search Documents

By Hayward B. Oblad, Gary F. Meenan

Two optoelectronic detectors were developed by CONSOL R&D for fine coal processing applications. One sensing device is used to estimate the amount of fine coal in the solids fraction of the froth flotation tailings slurry. The other probe, based on similar technology, is capable of measuring sol ids concentrations as high as 10 weight percent in fine coal slurry streams. These patented optoelectronic sensors are installed in several CONSOL coal preparation plants and are an integral part of the fine-coal control systems.

Jan 1, 1993

By E Asakpo, S Chaffer, A Heath

Newmont has had continuous production at their Ahafo operations, Ghana, since 2006. In 2013, Ahafo initiated an efficiency programme to improve mill performance and reduce energy consumption. Following this assessment, a Turbo Pulp Lifter (TPLTM) was installed in the Ahafo SAG mill in April 2015 to replace the existing radial pulp lifters. Plant operational data showed delivery of a power saving of 10 per cent, an improvement in throughput of 3.3 per cent, with no loss of grind size. Pulp lifter life was also doubled from 11 to 22 months.However, during subsequent relines when the grates were removed it was found that one in four of the outer pulp lifters were wearing at a faster rate than the remainder. This was investigated by Discrete Element Method (DEM) modelling, which predicted some overtopping and internal recycle within the pulp lifter. Significantly, the model predicted that the recycled material would pass back down every fourth outer pulp lifter, matching the field observations. Subsequently, the DEM investigation was continued and became an R&D project to improve the TPL design. The results are summarised here, leading to the development of the next generation Spiral TPLTM.CITATION:Heath, A, Chaffer, S and Asakpo, E, 2018. The development of optimised pulp lifter design for the Ahafo SAG mill using discrete element method modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 585–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Martin G. Wafforn, George J. Greer

"In early 2014, Pan American Silver Corp. commenced a project to construct a second shaft at its La Colorada underground mine located in Zacatecas State in Mexico. This was the first new shaft development project undertaken by Pan American Silver in the history of the company. The existing mine workings permitted the use of a raise bore for the excavation of the shaft opening, utilizing directional drilling in poor ground conditions to advance the pilot hole. This was an interesting project with many challenges and successes, and numerous lessons learned. The project was successfully completed in 2016, with the shaft operating at full mine production capacity within weeks. INTRODUCTION The La Colorada Mine has a long history dating from at least the 1920’s. The mine is located in the northern portion of Zacatecas State in Mexico in the Chalchihuites area, an approximate two hour drive south from the city of Durango. Pan American Silver acquired the La Colorada mining concessions in 1998, with mine production at that time consisting of only a few hundred tonnes per day. Over the course of the following 15 years, with the addition of an oxide processing plant and some expansions to the sulphide processing plant and site infrastructure, production was eventually increased to a maximum of 1,250 tonnes per day, all of it generated from conventional cut-and-fill stopes in the underground mine. An existing shaft was used to hoist the ore to surface, and over the years Pan American Silver had deepened the shaft and had changed out some of the hoisting plant. However, there were historic workings in close proximity to the shaft that made it unsuitable for personnel transport, and shaft maintenance was becoming difficult. The shaft was increasingly considered as a risk to the long term production continuity, and also to further deepening of the mine. In addition, expanding the capacity of this old shaft was not possible. Drilling of the La Colorada mineralization at depth commenced in 2010, with very good exploration success. As a result, by the end of 2013, the mine reserves had grown to a total of 6.5 million tonnes of high grade ore (388 g/t Ag, 0.36 g/t Au, 2.4 % Zn, and 1.3% Pb). Furthermore there were more (and higher grade) sulphide reserves than oxide reserves at depth. Following the completion of an internal study in 2013 with assistance from one of the international shaft contractors, a decision was made to increase the production from the mine with the construction of a new shaft and a new sulphide processing plant, a project with a calculated payback of 2.2 years."

Jan 1, 2019

By Norman O. Lotter, Lori Kormos, Greg J. Wilkie, Peter J. Whittaker, Johannes S. Stickling

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from Mineral Processing and Mineral Science.More recently, Process Mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX / WDX capabilities and an XRD, the development of Process Mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By J. S. Stickling, P. J. Whittaker, N. O. Lotter

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from mineral processing and mineral science.More recently, process mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (quantitative evaluation of materials by scanning electron microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX/WDX capabilities and an XRD, the development of process mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By Renato G. Bautista

"The development of processing methods for the preparation .of three electronic materials with rare-earth components is discussed. The resulting processing innovations are the results of a search for an economically competitive pilot scale or industrial production flowsheet without compromising the required properties of the final products. The three cases highlighted in this presentation are: 1) The preparation of high energy (Pr-Nd-Ce)FeB magnets for MRI application from a mixed-rare-earth oxide with a narrow range of composition directly prepared from the solvent extraction circuit of bastnaesite ore. 2) The kg production of the giant magnetocaloric effect Gds(SixGe1-x)4 magnetic refrigerant materials from commercial grade gadolinium metal (95 to 98 at. % pure) instead of high purity gadolinium metal (99.8 at. %); and 3). An industrial chemical synthesis flowsheet for the production of the superconductor precursor of YBa2Cu3O7.INTRODUCTIONIn the laboratory discovery stage, the synthesis of a new material is carried out using very high purity components, usually the highest purity available. As the new material is studied and characterized, the effectiveness of its desirable properties becomes better defined and understood. The evaluation of the effectiveness of the .property over the range of a given parameter and other interactions are further studied. Once it's potential application becomes clear, a practical and economical processing method need to be developed. The successful material processing flow sheet does not necessarily have to be a scale up of the laboratory procedure. At this stage, substitution of starting components and with lower purity materials is considered as the economics of the processing becomes a major issue. In addition, other approach to it's synthesis"

Jan 1, 2000

The following paper on the development of processes for the treatment of crude ore, accumulated dumps of tailing and slime at Broken Hill, has been prepared by a committee of the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy, with the object of recording, in chronological order, the developments of the various processes which have led up to the metallurgical practice of the present day.

Jan 1, 1930

There is a well-known saying, variously attributed to the great King Solomon and other sages of antiquity, to the effect that 'there is nothing new under the sun'. The inventive genius of man, as far as it is personified in the metallurgist, has often had the truth of this statement poignantly brought to mind when investigating the priority of ideas in its own particular branch of science. Not infrequently some operation, at first inilocently taken for a novel procedure, has later been found to have had an irrefutable precedent in the more or less remote past.When confronted by a question of this kind the metallurgist can generally much simplify his search if he at once turns his scrutinising gaze towards that ancient home of metallurgy, Germany. Vast departments of the smelting art have originated there, and even when Germany has not been in position to claim priority of invention, it has at least been characterised by a distinction equally as worthy - ie that of the faithful and authoritative exposition of the theoretical grounds on which the invention rests.In the present instance, in endeavouring to trace the history of pyritic smelting, the writer has naturally turned in the abovementioned direction, and not without some result, although the recorded data are, as might have been expected, meagre. A complete history of the art of beneflciating ores by means of fire, in all its many ramifications, still remains to be written. Possibly it may never be written, for the extent of the subject is tremendous. It is even practically impossible to clearly trace the development of one of its most modest sub-branches in satisfactory detail, or to present that branch without going to a considerable extent into related matters of a merely general character. For the purpose of dealing with the subject it will be convenient to divide it into two concurrent heads, and to distinguish, for historical reasons as well as for metallurgical ones, between that branch of the general method of matte smelting, which, until about 1891, has been called 'pyritic smelting', and the more recent offshoot of the latter, which, by distinction, may be called 'pyrite smelting'. The nature of pyritic smelting was clearly defmed by Dr John Percy in 1880, and his interpretation3 may be accepted as well known. To recall the characteristics of the method we may perhaps paraphrase Dr Percy's meaning by describing the process as a special method for the smelting of lean or dry silver or gold ores, which do not contain sufficient lead or copper for these metals to act conveniently as collectors of the precious metals. The operation is conducted in a blast furnace, with an amount of carbonaceous fuel sufficing to produce an exclusively reducing atmosphere, and with the addition of pyrites, in order to form a regulus in which the precious metals shall be concentrated, the pyrites themselves being either argentiferous, auriferous, or cupriferous, or any combination of these three, or wholly barren of metal values. In the common acceptation of the term, it is understood that the use of the reverberatory furnace is excluded.

Jan 1, 1994

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By R. Heunis

The hazard of rock bursts and rock falls as experienced in South African gold mines is examined in the light of recent research findings. The problem areas include high fatality rates, losses in production and equipment, and a detrimental influence on the recruitment of labour. The nature of the hazard is analysed, and it is shown that rock bursts are strongly related to the spatial rate of energy release by mining but that rock falls are not. The role of blasting and geological discontinuities is discussed. Practical rock-burst control strategies are compared, including the use of stabilizing pillars, back-filling and, in particular, techniques for reducing the frequency and severity of accidents resulting from large rock bursts. The latest stope-support experiments and their potential implications to mining are consid~red. It is concluded that a better understanding of the rock-burst and rock-fall hazard has resulted from the industry's research efforts. The findings can be applied towards obtaining an improved underground environment for men and machines.

Jan 1, 1980

By Blott S. F

The smelting plant and equipment at Mount Isa, as originally designed and built, was described by J. M. Callow (1) *.F. A. Forward (2) described alterations and additions to the plant and discussed the metallurgy of mixed carbonate-sulphide concentrates at Mount Isa, prior to 1933, in the Proceedings of this Institute.In 1933, A. F. McAskill (3) gave full mechanical details of the plant in a paper presented to the Institution of Engineers, Aust.FLOW SHEETSFig. No. 1 represents the present general flow sheet. Forward's (2) flow sheet is reproduced here as Fig. lA, and will serve for comparison in depicting subsequent deletions from, and alterations and additions to, the plant.Fig. No. 2 presents the daily tonnage flow sheet of 1939 practice.ALTERATIONS SINCE 1933General. Many changes in metallurgy and operation have taken place, particularly subsequent to March, 1935, when the treatment of a mixture of carbonate and sulphide ores was discontinued and the mill commenced operating on all-sulphide ore. This alteration brought about the elimination of gravity concentration-Jigs and Tables and resulted in the production of all-floatation concentrates of a very fine sizing. Refer Table No. 2, page?) Radical changes in the analyses and physical nature of concentrates also followed (see Table Nos. 1 & 2, page ?) and, similarly, radical changes in the smelting plant have been slowly brought about.

Jan 1, 1939

By L L. Kuhar

The AMIRA International P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project is an interdisciplinary research collaboration between 17 global mineral companies and four research organisations aimed at providing support for the emerging industry trend of geometallurgy. The main aim of the project is to develop predictive geometallurgical indices which can be incorporated into a resource block model to maximise the commercial value of an orebody and to minimise the social and environmental impact of mining operations.Researchers at the Parker Centre/CSIRO have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. The focus of the small-scale leach tests has been to determine the leach index (relative indication of leach performance), recovery, impurity deportment, reagent consumption, effect of size/degree of liberation and mineralogy of samples for their relative ranking. Predictive tests for heap leach hydrology (related to agglomerate characteristics) and slurry rheological behaviour are also being developed.

Sep 5, 2011

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By A Satyanaga, H Rahardjo, K G. Mercer

The soil-water characteristic curve (SWCC) is one of the most essential soil properties in unsaturated soil mechanics. The water flow and storage characteristics of an unsaturated soil are closely related to the amount of water contained in the pores and the negative pore-water pressure in the soil. These are both in turn, related to the particle-size distribution and the plasticity of the soil. The SWCC is obtained by laboratory testing which is difficult to perform, costly and time consuming. There is a significant advantage in establishing typical SWCC envelopes for different soil types from a geotechnical design and analysis viewpoint. This paper presents some of the research work undertaken by UWA and NTU to develop SWCC envelopes for soil types classified in terms of the ASTM D2487 Unified Soil Classification System (USCS). This was done by establishing a large database of soils from across the world, classifying them according to ASTM D2487 and undertaking SWCC testing for each soil. This paper presents the SWCC test results from a selection of three of the most common soil classifications encountered in geotechnical engineering practise.CITATION:Mercer, K G, Rahardjo, H and Satyanaga, A, 2018. The development of soil water characteristic curves for soil types classified according to the USCS, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 263–273 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A. Gourlie

"This paper describes the performance properties of a new 95 ksi minimum yield strength, oil well casing grade designed specifically to resist hydrogen sulphide stress corrosion cracking, SSCc. The new grade, Soo-95SS, demonstrates NACE Tensile threshold values greater than 90% specified minimum yield strength, SMYS, and NACE Bent Beam values in excess of 12.7 x 1()4 psi. The new Soo-9588 grade also exhibits superior collapse and notch toughness values. IntroductionIn recent years, a trend toward casing grade specialization has resulted in the introduction of numerous proprietary grades designed specifically for particular production environments, In response, Algoma Steel has developed, as part of a "" grade for service"" philosophy, two new 95 ksi minimum yield grades. The two grades are Soo-95, High Collapse (HC), and Sour Service (SS). This paper describes the development of Soo-95 Sour Service.Four main objectives were established:1. Definition of the steelmaking and continuous cast processing practices2. Determination of the acceptable maximum and minimum levels for all chemical elements3. Definition of special processing requirements4. Definition of the physical characteristics and ranges of the product properties.This paper provides a description of the experimental approach, followed by a presentation and discussion of the trial results . Finally, a number of conclusions are given."

Jan 1, 1988

By V. Nemec

The paper deals with further progress of the space and time models achieved since some of the previous APCOM symposia (1970, 1975, 1980) where original methodology was presented. Various transformations, de- and retectonization of space models, transfer of patterns, interactive time models are among the most important improvements. Enlarged possibilities of practical applications of the developed system are shown.

Jan 1, 1986

By Derek C. Shelton

This chapter covers the preparation of specifications for a dry crushing and wet grinding comminution circuit.

Jan 1, 1982

The paper explains the genesis of the Ballarat College of Advanced Education to its unique position in mining engineering education. A description follows of the development of the Graduate Diploma in Occupational Hazard Management which commenced in 1979 in the cooperative mode of four groups of three weeks full- time study followed by twenty-three weeks in industry. In particular an analysis will be given of the state of origin of students, ages and employing industries. Given the experience from the evolution of this course a similar process is described for the Graduate Diploma in Mining which has been accredited to commence early in 1987.

Jan 1, 1986

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003

By F. Doxey

Introduction In order to improve outputs and to reduce or hold mining costs, many attempts have been made to mechanize the getting and loading of coal in the major coal producing countries, and machines of various kinds and sizes have been designed and manufactured. Some of the most important are: Joy Continuous Miner Joy Coal Auger Goodman Mining Machine Lee-Norse Koal-Master Jeffrey Colmol Cardox Hordsecg Recovery Drill German Coal Plough British Coal Plough with agitated blades M. & C. Samson Stripper AB Meco-Moore Cutter Loader Joy Gloucester Getter The three last named are the chief longwall machines in use and the AB Meco-Moore and the Samson Stripper are doing a good job in their respective applications. It is understood that the Gloucester Getter recently installed in a British colliery also shows reasonable promise. It was felt, however, that to meet the conditions of the mines in Nova Scotia, any machine developed must have certain distinctive characteristics. It must: ( 1) Be able to cut and deliver coal in quantity and of the right sizes ( 2) Be easily manoeuvrable ( 3) Be suitable for longwall operations ( 4) Not interfere with timbers already set ( 5) Cut its own stable (6) Work on reasonably heavy gradients

Jan 1, 1951