Search Documents

By G. A. Gillett, C. F. Bonney

"The Davy McKee combined mixer-settler (CMS), is a liquid-liquid contactor, which has been commercially applied to the recovery of uranium from dilute sulphuric acid-bearing leach liquors. CMS differs from most other solvent extraction systems in that the mixing and separation of the phases is carried out in the same vessel.IntroductionTypical solvent extraction plants for the recovery of uranium operate at organic to aqueous feed flow ratios of 1 : 2 to 1 : 30. Because it is beneficial to mix the organic and aqueous phases at an organic/aqueous (O / A) ratio of between I : 2 and 2 : I there is incompatibility between the over-all and operating O /A ratios.Conventional mixer-settler designs require an external recycle of the minority flow which results in the possibility of over-mixing, increased settling requirements and entrainment losses. Other workers have approached this problem in terms o f enhanced sett ling and this has been partly successful.Davy McKee's approach involved a radical rethink of the principles of liquid-liquid contact and separation.Description of CMSThe CMS has the important advance that the required mixing O/A ratio can be achieved without external recycle and is not affected by the O /A ratio of the feeds. Three zones co-exist within the CMS unit-a central mixing zone and upper and lower separation zones. A pump impeller on a draught tube is installed within the mixing zone and baffles are installed above and below the mixing zone. Conventional mixer- settlers have several undesirable features which ca n largely be eliminated using the CMS system:"

Jan 1, 1983

By David C. Girard, Larry Williamson, Leonard R. Benson, Ronald E. Bizzarri

On the east side of Washington DC, the DC Water & Sewer Authority is developing a Facility Plan for the Anacostia River CSO Control Projects, including 8 to 12 miles of CSO storage/conveyance and flood relief tunnels and associated facilities. The project includes major technical and non-technical challenges, including: completion under a Federal Consent Decree schedule; large diameter (estimated 25 to 35 ft) soft ground tunnels and shafts up to 200 ft depth; operations without use of active flow control systems; and close coordination with several major public and private construction and development projects that are being advanced in the project area.

Jan 1, 2007

By H. Herbert Hughes

In the years following World War II, L. de Roll S.A., Zurich, Switzerland, perfected its vertical kiln. De Roll first became interested in cement-manufacturing equipment in 1947, not only kilns but also the crushing, grinding, and handling equipment required for a complete cement plant. The parent company, Louis de Roll Iron Works, S.A., Gerlafingen, Switzerland, was founded in 1804. In its six plants, and with its associated companies, de Roll manufactures and installs equipment for a wide variety of industries-chemical and metallurgical operations, fats and oils plants, and municipal refuse incinerators and sewage disposal installations. Vertical shaft kilns, of course, are as old as Portland cement itself. Their fuel economy has long been recognized, particularly in Europe where fuel costs are high. But the disadvantages of old-type shaft kilns have been the lack of consistent quality of the clinker, the small capacity, and the relatively high labor costs.

Dec 1, 1956

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

By Z. Kwela, A. Manhique, W. W. Focke, W. van der Merwe

"The main features of the de Wet improved alkali fusion process for the manufacture of AZST are: Fewer process are steps necessary; radioactivity is removed by leaching rather than by precipitation; fewer waste streams are generated; there is less waste to discard and alkali reagent is recovered in the form of a sodium silicate solution that is essentially free of radioactivity.Here we report on our efforts maximize the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated. The fusion products were characterized by infrared spectroscopy, X-ray diffraction and by wet chemical analysis.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since these compounds do not hydrolyze in water they limit the recovery of alkali in the sodium silicate product stream. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed."

Jan 1, 2003

By Michael J. Shulman

The DEAREX knowledge acquisition and engineering system is a teaching and exploration tool designed to facilitate the under- standing and development of expert systems by explorationists without the aid of a knowledge engineer and without recourse to expert system languages. To fulfill its objective, the DEAREX system considers the selection of exploration methods in desert areas. The system consists of three parts: 1. A tutorial which introduces the basic and selected advanced concepts of expert systems, 2. A sample program illustrating how an expert system works and can be used, and, most importantly, 3. A knowledge acqusition and engineering program which enables users to develop their own expert systems. The tutorial provides a brief and concise introduction to expert systems, a 10 rule exploration example which defines, explains and illustrates the basic concepts and design of expert systems, and a glossary of expert system terms including cross references. The sample program is a larger, self contained example of an expert system with some commentary illustrating addition- al expert system concepts and the role of the knowledge engineer in particularizing rules and ascertaining the knowledge base. Restricting itself to the selection of exploration methods in desert areas, the knowledge acquisition and engineering program questions the user and converts the answers into an expert system. Questions pertain to geology, infrastructure, availability of instrumentation, personnel, etc. Additional information may also included. In conclusion, some salient points concerning knowledge engineering toolkits, shells and knowledge acquisition capabilities such as contained in DEAREX are discussed.

Jan 1, 1992

By G. A. Campbell

Mining companies have been very interested in the presence of a number of small but high-grade ore bodies of base metals in northern Wisconsin and the west/central section of the Upper Peninsula (UP) of Michigan. The region is rural with outdoor recreation/tourism and lumbering being the key industries. The economy of the region is based on the use of its natural resources, and mining is not a new activity to the region, especially the UP. The western UP was historically a key mining district for copper and iron, and today the central UP has a significant iron-mining district. However, all efforts to develop the base metal ore bodies have been met with a storm of controversy involving the local community, regional activists, Native Americans, and the state government, and only one mine has gone into operation. There is concern by some stakeholders about the sustainability of mining in communities that depend on the environment for tourism, recreation, and other commercial activities. There have been four attempts to get the necessary approvals to mine in this region: the successful Flambeau Mine effort (Wisconsin), the failed Crandon project (Wisconsin) and Lynne project (Wisconsin) efforts, and the continuing effort to get the Eagle Project (UP of Michigan) approved. The cases are presented to illustrate the project situation, the history of the permitting effort, and the opposing parties and their concerns. The case of the Eagle Project is looked at in detail by using the method of discourse communities and discourse analysis. Results of the analysis provide insight into the communication efforts to address community concerns about sustainability and what more can be done to improve this dialogue.

Jan 1, 2008

By Stanley J. Gasior, Albert J. Forney, Joseph H. Field

Most bituminous coal mined near Eastern industrial areas requiring high-Btu pipeline gas is caking and therefore unsuitable for fixed-bed pres- sure gasification by present techniques. If the caking property of such coal can be destroyed, the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work, strongly caking coals of 1/8- to 1½ -in. size were converted to a noncaking coal char by treatment in a static bed in about 3 hours1 and coal of 18-100 Tyler mesh in a fluidized bed in about 5 min.2 An inert gas such as steam, nitrogen, carbon dioxide or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a noncaking form in free-fall in about 2 sec by dropping it through a countercurrent flow of steam containing 4% to 7% oxygen at 1150º-1200°F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 3, 1965

By B J. Wilde

Evaluating the resources and reserves in a mineral deposit requires many interdependent subjective decisions. The decision of stationarity is arguably the most important. This decision includes: the choice of domains that subset the entire deposit, modelling the boundaries of each domain, and understanding and considering the nature of the contacts between domains. Reasonable choices are made in consideration of the geological context, the available data, the goals of the study and the available resources for the study. This paper reviews aspects of the decision of stationarity in modern resource assessment with a focus on quantifying uncertainty and using numerical/statistical tools to help the geomodeller. The use of volume/distance functions to quantify uncertainty in domain limits is particularly important and is presented in detail. The use of contact plots provides help with the continuity of grades across domain boundaries. Realisations are not assembled as a branching combinatorial of all possibilities, but as a set of realisations that provide a measure of uncertainty. This paper amounts to a definition of stationarity for modern resource assessment.

Sep 26, 2011

By H. O. Hofman

WITH the exception of lead sulphate, all common metallic sulphates are completely decomposed upon heating into metallic oxide, sulphur trioxide, sulphur dioxide and oxygen. Some give up their trioxide readily at a low temperature, others require considerable heat and much time to be completely freed from sulphur. Kerl in 1881 arranged the principal metallic sulphates as they are decomposed by a rising temperature in the following order: silver, iron, copper, zinc, nickel, cobalt, manganese and lead, lead sulphate being decomposed only slightly at a white heat. The researches of Bradford, published in 1903, show, however, that ferrous sulphate is decom¬posed at 590° C., cupric sulphate at G53° C. and argentic sulphate at 1,095° C. By the present investigation it will be seen that zinc sulphate is decomposed at 739° C. As far then as our present knowledge goes, the order in which the decomposition of the leading metallic sulphates takes place is the one given in Table I.

Jan 1, 1905

By W. Mostowitsh

I. Introductory LEAD sulphate occurs as anglesite, and is formed in every roasting of lead sulphides or sulpho-salts containing lead. In smelting in the blast furnace an ore containing natural or artificial lead sulphate, a large part of the sulphur present goes to the formation of the intermediary product matte which requires further treatment for the recovery of the values it contains. It is therefore of importance to study the behavior of lead sulphate at elevated temperatures, both without and with reducing agents, especially as the information available gives data which are more or less conflicting. II. Decomposition of Lead Sulphate by Heat The dissociation of PbSO4 into PbO and S03 or S02 and 0 has been discussed by many metallurgists. The following data are considered to be representative. Doeltz and Graumann1 found that PbSO4 was not affected by heat at 800° C.; that dissociation began at 900° C., and was rapid at 1,000° when the salt lost in 1 ½ hr. 14.3 per cent. of its weight, the dry salt containing 26.43 per cent. SO3. Hofman and Wanjukow2 summarize their work upon the dissociation of metallic sulphates with the statement that the decomposition of PbSO4 begins at 195° C., but progresses very slowly, with the formation of the basic salt 6PbO.5S03 at 705°; that this salt undergoes a transformation at 847°, begins to be decomposed at 888°, to sinter at 896°, and to fuse at 910°; rapid dissociation begins at 952°, and is accompanied by volatilization of PbO; retardations at 958° and 962° indicate an acceleration of decomposition which, however, is not complete. Proske3 found that PbSO4 gave off at 900° C. in 30 min. only 0.63 per cent. of its SO3, and that the loss increased with

Jan 5, 1916

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, ? bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of 2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, 1£ bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By W. WANJUKOW, H. O. Hofman

(New York Meeting, February, 1313.) I. INTRODUCTION. IN the metallurgical treatment of most metallic sulphides it is usually necessary to carry on a roasting-operation. In some cases the raw ore will have to be roasted.; in others the intermediary product, matte, produced in smelting the ore; again, both ore and matte may have to be subjected to oxidation at elevated temperatures. Most metallic sulphides, when given an oxidizing-roast, pass through the state of sulphate before they are converted into oxides. All metallic sulphates are completely decomposed by heat, with the exception of those of lead and bismuth, but the temperatures at which decompositions take place vary with the metals. Some metallic sulphates are converted directly into oxides, others first form basic salts. Alkali-earth sulphates show a behavior similar to that of metallic sulphates, while alkali sulphates do not part with their sulphur trioxide even at elevated roasting-temperatures. The older data on the decomposition of metallic sulphates by beat are only approximations. Thus Kerl 1 gives the order in which metallic sulphates are decomposed with increasing temperatures as (Ag2, Fe, Cu, Zn, Ni, CO, Mn, Pb) SO4. More recent statements give definite temperatures and modify the formerly accepted order of decomposition. But the temperatures given by various observers do not agree. The reasons for this are to be found mainly in the method and manner of carrying out experiments. Four methods have been used: 1. Heating in an evacuated tube; 2, heating in a tube closed at one end, without air-cur-

Sep 1, 1912

Experimental investigations were made into the decoppering of lead, tin, and bismuth using a technique which approximates on the small scale to industrial practice.Decoppering lead with sulphur alone in the absence of tin and silver did not proceed to low copper values. With a minimum of 0·02 per cent Ag or 0·10 per cent Sn, lead was decoppered to less than 0·01 per cent Cuby stirring with 0·2 per cent S over 10 min. Decoppering of tin or bismuth proceeded rapidly to very low levels in the absence of any "catalytic" impurities, at any rate in excess of those concentrations normally encountered in commercially pure tin or bismuth.

Jan 1, 1971

By Henry Hebley

IN recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and clean-ing of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal.

Jan 1, 1933

"TREVIICOS CorporationINTRODUCTIONThe Walter F. George lock and dam was constructed on the Chattahoochee River between 1955 and 1963 with the double function of improving navigation and generating power. Its 82 ft. by 450 ft. (25m x 137m) lock can accommodate large barge traffic and its four generating units with a plant capacity of 150 MW have an average energy output of 453,000 MWH. The dam consists of a 1,496 ft. (456m) long concrete structure housing the spillway, a non overflow portion, the power units and two earthen wing dams extending to the Georgia and Alabama sides, respectively 5,810 feet and 6,130 feet long (1770m and 1868m). As soon as the reservoir was impounded it became apparent that excessive seepage was occurring. From 1962 to 1985 a series of remedial works was performed using several techniques, but the problems continued under the dam, jeopardizing its generating potential and possibly undermining its stability.Finally, the decision was made to construct a deep cutoff primarily under the concrete portion of the dam to remedy the problem. PROCUREMENTOn July 5th, 2001 best and final offers were solicited by the Corps of Engineers (COE) for the construction of a deep cut-off to be built in front of the concrete portion of the dam from the bottom of the lake and tied into it. The cut-off had to cross an existing lock structure and an underwater retaining wall, as well as the remnants of a steel coffer cell left in place from the initial construction.The specifications required that the wall be built with a minimum thickness of 24” (600mm) and that it extended from the bottom of the lake to elevation -5 (1.52m) into the Providence formation, an impervious layer.While the land portions of the wall were on average 208 feet (63.4m) deep, the marine portion started from up to 90 feet (27m) of water and continued through different rock formations for another 100 feet (30m).Contractors were invited to propose their own method of constructing the cut-off and offers would be evaluated using several criteria, including technical, economical, organizational and experience.Three proposals were received and on August 14, 2001 an award was made to the Joint Venture (JV) of Treviicos and Rodio."

Jan 1, 2014

By A. Tarigan

The integration of the ESZ orebody and DOZ orebody resulted in a much larger footprint than the original DOZ Mine shape. The significant change in footprint geometry presented new cave front management challenges, specifically: longer undercut drifts. Using a constant blasting rate, more time is required to complete caving in each drift which ultimately influences the number of active faces at any point in time. The number of manageable active drifts is controlled by the planned square-meters of undercut blasting, lead/lag restrictions and other specific conditions such as the need to blast pre-charged explosives. In early 2008, an evaluation of the existing plan showed that significantly more active undercut drifts and longer cave fronts would occur in the next five years. Difficulties associated with the long cave fronts led to a decision to redesign the caving sequence. Several different boundary options based on operational, geotechnical and ore grade parameters were investigated. This paper describes the issues faced with long cave fronts, the constraints and requirements to effectively manage the caving sequence and the options considered to mitigate this situation.

Jan 1, 2010

The Kiirunavaara apatite-magnetite orebody is about 4 km long and approximately 100 m thick sheet-like body, which lies roughly in a north-south direction and dips from the horizontal plane along its entire length, in towards the town of Kiruna. The origin of this orebody has been a matter of controversy, with both magmatic and hydrothermal origins proposed. Traditionally and for practical purposes this rich apatite-magnetite ore has been divided into two main types: low phosphorous ore (B-ore) and high phosphorous ore (D-ore). Further the low phosphorous ore is divided into the low alkali (B1) and the high alkali (B2) ore.

Jan 1, 2006

By Federico Pagliacci, Marco Chiarabelli, Salvatore Miranda

The paper describes the adopted technologies and performance controls related to a special geotechnical engineering solution provided within the scope of the Galataport Project, in Istanbul, Turkey. The scheme is the one applied to the new quay of Salipazari, which is a combination of retaining structure and ground improvement, formed by a combi-wall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high profile Project. The results of the in-situ and laboratory tests carried out on the improved soil are also presented. Main discussed points are: • History of Galataport and main Project details. • Design principle and soil condition for the new quay of Salipazari. • Difficulties encountered during execution of DSM. • Preliminary field trial tests conducted to establish the operational parameters, with relevant in-situ and laboratory tests executed. • Preliminary tests on material used for DSM (seawater and CEM IV SR). • Electronic equipment mounted on the rig, which allows the automatic execution of DSM columns. • Final QA/QC tests conducted to verify the performance of DSM, mainly consisting in: coring with relevant laboratory tests on samples (UCS + Es), seismic refraction tomography and seismic cross hole tomography. Correlations between UCS and Es, and between Es and Edyn are also presented. • A cross section of the executed treatment could be inspected on site during excavation. Photos and considerations are also presented.

Jan 1, 2018