Search Documents

By A. E. Cameron

The curve of coal production in Nova Scotia over the past forty years shows a definite maximum reached in 1913. Continued production to this maximum will require a greater tonnage per man-day, and this means there cannot be any increase in total man power used in the operations. There are still large reserves of coal but much of it will require washing or beneficiating to make a usable product. By-product recovery based on the present product ion is relatively satisfactory. Further development of secondary industries requires adequate markets for the bulk materials produced by the processing. It also requires access to other raw materials as well as markets for the principal product of the operations. Scientific investigation and research are needed to prove the quantity and value of lower grade or poorer quality coals, and methods for their recovery and utilization. Economics of further processing of present and future production must be investigated beforehand, if a successful development is to be assured. Such development cannot be expected largely to replace present markets. Production of coal for genera l use must continue to form the major function of the coal industry of the Province. Costs per ton must decrease, or subsidies or other assistance must increase, if the industry is to survive. Costs of investigation and research and costs of capital outlay for further development muse be met.

Jan 1, 1944

By Z. H. Liu

We experimented with slurry which from one of coal preparation plant in Guizhou province and made researches on double hump gradation, one of critical factor of gradation technology, which can influence pulping character in the process of making coal water mixture (CWM). The purpose for it is to find the best particle gradation which can meet the requirements in concentration, viscosity, and stability for CWM. The final result is that the concentration, viscosity, stability of CWM can meet the requirement for industrial use while the rate of fine particle in the slurry is 70%~75% and the maximum concentration of 62%.

Jan 1, 2014

By Edward W. Parker

This plant was built in 1907 at the Bankhead mines to manufacture briquettes by the Zwoyer process under license from the Zwoyer Fuel Co., of New York, N. Y. The building was constructed to contain two units, each of a capacity of 10 tons per hr.; one unit was installed at the time the building was constructed, and the second unit is now being built. The coal used is an anthracite, which is more friable than that of Pennsylvania, and, as a consequence, a larger percentage of dust or waste is produced, which was formerly thrown upon the slack-pile as waste, but is now passed to the ? dust-bin " in the breaker, from which it is conveyed to the briquette-plant.

Jan 5, 1908

By B. F. Bush

THE coal-fields of Missouri, situated hi the northern and western portion of the State, are distributed, in whole or in part, over 57 counties, embracing an area estimated by Mr. Broad-head to be practically 23,000 sq. miles, including small detached beds and outliers in St. Louis, St. Charles, Lincoln and Warren counties in the eastern part of the State. This area includes about 8,000 sq. miles of Upper or Barren Measures, 2,000 sq. miles of exposed Middle, and 12,420 sq. miles of exposed Lower Measures. In a general way, the Missouri coal-field is bounded on the east by an imaginary line entering the northern part of the State just east of the 92c1 Meridian and passing across the State in a southwesterly direction to a point on the Kansas-Missouri line a little below the southern boundary of Barton county. An important part of the field overlaps this line and extends down the northern side of the Missouri river, under¬lying the greater part of Randolph, Howard, Boone and Audrain counties. In all, 34 counties produced coal during the year 1903. Fig. 1 shows the position of the coal-fields in Missouri. GEOLOGICAL FEATURES. The Coal Measure formations, all of the Carboniferous age, rest unconformably upon the rocks of the sub-Carboniferous or Mississippian series, and, in some cases, upon the rocks of the Devonian and Silurian ages. From their outcrop on the eastern and southeastern borders of the field, the Measures dip west to northwest at the rate of 10 ft. per mile, reaching a maximum thickness estimated by

Jan 1, 1905

By MARIUS R. CIMPBELL, Edward W. Parker

DESCRIPTION. ACCORDING to the estimates prepared by the U. S. Geological Survey, the area underlain by workable coal-beds in the United States is 496,776 sq. miles. Of this total area, 480 sq. miles contain the entire anthracite coal-fields of Pennsylvania. The bituminous coal-fields are estimated to be contained in areas aggregating 250,051 sq. miles. The grade of coal between bituminous and lignite, and which is designated by the Geological Survey as " sub-bituminous," is estimated to be contained within areas aggregating 97,636 sq. miles, while the areas containing lignite aggregate 148,609 sq. miles. The coal-fields are divided, for the sake of convenience in classification, into six main provinces, as follows: 1. The Eastern. Province, containing the anthracite coal-fields of Pennsylvania and the bituminous coal-fields of the Appalachian region-namely, those of western Pennsylvania, Ohio, Virginia, West Virginia, Kentucky, Tennessee, Georgia, Alabama, and small outlying areas in North Carolina. 2. The Interior .Province, containing the bituminous coal-producing regions of Michigan, Illinois, Indiana, western Kentucky, Iowa, Kansas, Missouri, Oklahoma, Arkansas, and Texas. 3. The Gulf Province, containing the lignite-areas of Alabama, Mississippi, Louisiana, Arkansas, and Texas. 4. The Northern or Great Plains Province, containing the lignite and sub-bituminous areas of North and South Dakota, eastern Montana, and northeastern Wyoming. 5. The Rocky Mountain Province, containing the bituminous and sub-bituminous areas of western Montana and western Wyoming, Colorado, Utah, and New Mexico. 6. The Pacific Coast Province, containing-the areas of Washington, Oregon, and California.

Apr 1, 1909

By JO. E. SHERID

THE Dawson coal-mines are owned and operated by the Stag Canon Fuel Co., of which Dr. James Douglas is President and E. L. Carpenter general manager. The property is situated in Colfax county, N. M., and the openings now in operation are in townships 28 and 29 N. R. 20 E., and township 28 N. R. 21 E., shown in Fig. 1. The mines are part of the southern end of the Raton coal-field, which extends north into Colorado and embraces many coal-camps of the Trinidad section. II. GEOLOGY. Geologically, the coal-measures, commonly known as the Laranmie series of the Cretaceous system, have a thickness of about 800 ft. in the vicinity of Dawson. The coal makes an excellent coke, and, according to some authorities, its coking properties are clue to the action of intruded sheets and sills of igneous rock, the sheets occasionally thickening into masses resembling laccoliths, at such places making nearer approach to the coal and sometimes producing small areas of natural coke. There are but few dikes through¬out the entire southern portion of the field and little or no faulting along the dikes. In some parts of this great coal-field the intrusive sheets are far removed in the green shales below the coal-measures, and are so much altered as to be difficult of identification. There is but little disturbance of the strata through¬out the Raton coal-field in as far as it extends into New Mexico. There are two workable seams in the coal-measures, and two or three smaller coal-seams, ranging from 1 to 2.5 ft. in thick-

Jun 1, 1909

By Edward Pesout

THE McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.1 EARLY PULVERIZING PLANT Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a finer product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. [ ] It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. 0-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1945

By John Tyssowski

IN 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temper-atures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several parti-cles had become one unit. From this dis-covery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the appli-cation of about 30c0 tons pressure on a 10-in. piston. Stout decided that cathode copper pro-duced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H, Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles.

Jan 1, 1940

By John Tyssowski

IN 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temper-atures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several parti-cles had become one unit. From this dis-covery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the appli-cation of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper pro-duced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable

Jan 1, 1940

By M Colwell

The Coal Mine Roof Rating (CMRR) is a rock (roof) mass classification (RMC) system/index that was originally developed by the United States Bureau of Mines (USBM) for aspects of underground coalmine geotechnical design and was first introduced to Australia as a part of the original Analysis of Longwall Tailgate Serviceability (ALTS) project conducted in 1997/1998. In subsequent years further refinement to its calculation was undertaken, such that the CMRR is now an industry standard for quantifying the structural competence of the primary bolted roadway roof interval and has been routinely/widely used by Australian collieries over the last 25 years with great success for roof support/chain pillar design. There have been many publications discussing the use and calculation of RMC systems and this paper also provides an important update and recommendations in how best to calculate the CMRR. However, it is rare to find an explanation as to why and how a RMC system/index satisfactorily takes account of the mechanics and rock mass behavioural issues associated with ground reinforcement. This paper provides such an explanation and insight with respect to the CMRR so it is: 1) better understood, 2) to allay any concerns, and therefore 3) will continue to be confidently used by and for the collieries’ benefit.

Nov 29, 2022

By T. Sterry Hunt

BUT little was known of the coals of Southeastern Ohio until the present survey of the State under Dr. Newberry began its work. The results of the geological investigations of Prof. E. B. Andrews in this region, and of the chemical investigations of Prof. T. G. Wormley, both of which appear in the reports of the survey for 1869 and 1874, and more recent special reports by the former, together with some data for which I am indebted to the kindness of Dr. Newberry, and my own limited observations, have served me for the preparation of the following notice of the coals lying on the western border of the great Appalachian coal-basin in the region drained by the Hocking River and its tributaries, and belonging to the Lower Coal-Measures. Some uncertainty exists as to the place in the succession of the lower coals to be assigned to the seams known and mined in the Hocking Valley. It is the opinion of Prof. Andrews that the inequalities of the original surface were such that we cannot identify in that region the lowest coals known in Northwestern Pennsylvania and the contiguous parts of Ohio, but that we must rather count from above downwards. These conclusions Dr. Newberry is not prepared to accept, and further researches will be necessary before certainty can be attained in this matter. Meanwhile it seems, from a study of its relations to the Pomeroy or Pittsburgh seam, that what is known as the great vein of the Hocking Valley, occupies the horizon of the Upper Freeport coal, E of the Pennsylvania survey, or No. 6 in Dr. Newberry's enumeration, counting from the base. This seam, in the region in question. assumes certain characteristics which, taken in connection with its geographical position, give it a great importance among the coals of the State. The area to be noticed includes the whole or parts of several townships in Perry, Hocking, Vinton, and Athens Counties, lying near the margin of the basin over which the vein in question assumes the character of a dry-burning or splint coal, and has a thickness varying from six to ten and even twelve feet. Its precise limit southward cannot at present be clearly defined, but it has been found as far south as the line of the Marietta and Cincinnati Railroad, with a thickness of six feet, and is mined at various points along the valley of the Hocking River, near Nelsonville, where it attains six or seven feet. To the northward, along the tributaries of this river, Sunday and Monday

Jan 1, 1874

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By G. S. Hill, B. J. Huls

This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed the authors to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flowsheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit.

Jan 1, 2006

By Gregg S. Hill, Bert J. Huls

"This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed us to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flow sheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit. Details of the technology behind each unit operation will be presented in later publications.INTRODUCTIONSince 1996 BHPBilliton and MEL (Minera Escondida Ltda.) have developed a process to recover copper from coarse particles in the rougher tailings. Copper recovery from fresh tailings is not new. Several operations in Chile, such as Chuquicamata, El Teniente (AMEC, 2003), Mantos Blancos and others have operated various forms of tailings circuits. Both Chuquicamata and El Teniente practice cascade flotation scalping off froth containing fine copper particles after allowing sufficient retention time, air inducement and, sometimes, additional reagent addition. Chuquicamata tailings are not segregated but floated in sequential cascade and conventional large cell arrangements. At the Valle Central operation of El Teniente a coarse fraction of mill tailings is ground and floated, with the rejects recombined with fine tailings and subjected to cascade flotation through a sequence of concrete launders as the tailings flow towards their final deposition area. Mantos Blancos cyclone the rougher tailings and blend the underflow with scavenger concentrate from elsewhere in the principal circuit prior to flotation in Wemco Cells. Kemess in BC, Canada operates a 160 m3 Outokumpu cell to reduce the tailings sulfur content (Rasmussen, et.al, 2004)."

Jan 1, 2005

By Dan Marshall, David H. Watkinson

Abstract - Cobalt, Ontario, is renowned for the 12.6 billion grams (445 million ounces) of silver produced from the area since discovery in 1903 by workers of the Timiskaming and Northern Ontario Railway. Native silver generally occurs with cobalt arsenides and sulfosalts in near-vertical carbonate veins cutting the Huronian sedimentary rocks of the Gowganda Formation, the Archean metavolcanics and/or the Nipissing diabase. All major deposits have been found within a few hundred meters of the unconformity between the Archean and Huronian rocks in general proximity to the Nipissing diabase and volcanogenic sulfide mounds within the Archean meta-volcanics. Silver has been mobilized from one or more of the local country rocks by hyper-saline brines and deposited in or near zones of mixing where the saline brines encounter paleometeoric water transported to depth along the unconformity or local structures. Previous work has shown that chloride complexes are the dominant ligands responsible for silver transport. These hypersaline brines, represented as halite-bearing fluid inclusions at room temperature, have been trapped as primary fluid inclusions within vein minerals. Pressure-temperature conditions of vein formation have been derived from mineral equilibria, maximum lithostat and fluid-inclusion studies. These data are consistent with vein formation occurring over the temperature range 300°C to 350°C, with pressures constrained between 60 Mpa and 136 Mpa (600 bars and 1360 bars).

Jan 1, 2000

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to '85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

By Arthur Forsyth

A SEARCH through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1.

Jan 1, 1940

By Thomas S. Falk, Nils G. Lindberg

The first industrial COBO (Cold Bound) pelletizing plant began operation in May 1975 at Trollhiittan, Swede n. A technical description of the process, together with operational experience with the plant, forms the basis of this paper.

Jan 1, 1976

The objectives of this paper are to introduce the International Code of Practice for Risk Management of Tunnel Works and to illustrate to the participants of the 13th Australian Tunnelling Conference 2008 how the insurance industry would like to see the future of tunnelling insurance. Tunnel construction projects have suffered large losses over the years as can be shown from various loss examples and a list of major losses over the last ten to 15 years. Since the consequences of insufficient risk control had to be borne by insurers, these losses have heightened the need for improved and adequate risk management measures so that insurance cover can also in future be provided for this hazardous industry sector. Observations are made as regards to the prevailing trends in the tunnelling industry, which contribute to the increase in risk and have adverse consequences for the insurance industry. To find a solution to this dilemma various options are examined with the suggestion of a Joint Code of Practice for Tunnel Works being agreed by all stakeholders, which would become essential to secure future insurance protection for such project work. The British Tunnelling Society has, in cooperation with the Association of British Insurers, developed such a code, which the International Tunnelling Insurance Group has now adopted for global application in international markets. The content and concept of this code is explained to establish a framework of understanding and applied risk management principles for tunnel works. This initiative also has the support of the International Tunnelling Association and the International Association of Engineering Insurers. The international application of this new code is demonstrated with a few examples, which also includes Australian projects. It is the aim that this code forms in future part of the insurance coverage for tunnelling works in order to put this risk segment on a more sustainable basis. For that reason the insurance industry is seeking the support of all stakeholders of tunnelling construction projects.

Jan 1, 2008

By M. Reda

Inorganic oxidizing agents of the type MeOx-z such as Chromate, Vanadate, Tungstate, and Molybdate... etc. are widely used as corrosion inhibitor. In non acidic solution these oxidizing agent are reduced on the surface of the meta, according to OX + m e + p H20 Red + n OH" In which y = (n-m)/m. The purpose of this publication is to show that for many metals the value of y for any oxidizing agent determines the possibility of that oxidizing agent being an inhibitor or activator for the corrosion process. The inhibition efficiency for other ions such as Pertecnetate and Tellurate which have not been extensively studied can be predicted. A mathematical, equation was derived to express the relationship among the concentration of oxidizing agent, degree of retardation of the corrosion process I cord cor ° (ratio of corrosion current in the solution containing inhibitor to the base solution) , ionic strength of the solution and the coefficient y. The validity of y and the mathematical, equation were verified by many experimental, works on various metals such as zinc, aluminum and steel. Al, the above research works are based on the published research works of Prof. Mikhailoviskii (from 1979 til, 1998) from the Russian Academy of Science.

Jan 1, 2010