Search Documents

By G. G. O. O. Uwadiale

Starting from a crude ore assaying 45.6% Fe, a fine-grained oolitic iron ore was concentrated by the oil agglomeration technique to 90% Fe recovery and 65% Fe assay. The ore required grinding to minus 5 µm to effect adequate liberation, and the technique yielded optimum results at pH 9. The roles of pH, collector, and bridging liquid concentrations on selectivity and yield of iron minerals in the concentrates are discussed.

Jan 1, 1991

By G. G. O. O. Uwadiale

Because mineral matter is finely distributed within the matrix, Nigerian Labia coal is nonresponsive to conventional processing techniques. However, testing has shown that Lafia coal can be upgraded by selective oil agglormation. The optimum oil concentration was found to be 10 mL of paraffin per 25 g of coal. A product containing 6% ash and 1.9% sulfur was obtained with a yield of 90%. Optimum results were achieved with a grinding; time of from 2.5 and 3 hrs, which produced a 98% -400 mesh product. However, further grinding wars found to be deleterious to the process. Also, high pH adversely affected concentrate yields. Utilizing kerosene as a bridging liquid, a product containing 4% ash and 0.33% sulfur was achieved at a natural pH of 6.3 with a yield of 85%. At pH 9 and 10, a product containing 4.5% ash was achieved with a yield of >90%.

Jan 1, 1997

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module (Fig. 1). The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information. Key for Fig. 1 A-Helium-3 neutron detector B-Wax moderator for neutrons C-Irradiation chamber D-Funnel for receiving ore E-Gate F-Transducers G-Biological shield for neutron source H-Transfer tube for neutron source I-Neutron source J- Microprocessor K-Accumulator for hydraulics L-Control panel M-Electro-hydraulic servo valve to control movement of the source N-Electro-hydraulic proportional valve to control movement of the gate O-Hydraulic power unit Irradiation and Counting Equipment Irradiation of the ore is achieved using a 1 X 10 7 neutron*s-1 californium-252 neutron source. The source is contained in an iron capsule and pneumatically transferred between the irradiation/counting and storage chambers. The irradiation/counting chamber possesses 12, 600-mm (24-in.) long helium-3 thermal neutron detectors embedded in an annulus of wax (Fig. 1). Two sets of six detectors are each interfaced to a preamplifier, amplifier and single-channel pulseheight analyzer system, and the two systems are connected to a scaler. A special timing unit controls the transfer of the source and the on and off switching of the detector assembly, in sequence with the movement of the source. Results and Discussion In the experimental demonstration, using the 107 neutron.s-1 source, a 10% uranium ore was measured to ± 10% (2o total error) in 10 cycles and ±6% (2o) in 100 cycles. Since a larger source was not available, it can be statistically predicted that a 109 neutron-s-1 source could be used to measure a 0.1% ore to ± 10% (20) in 10 cycles. The uranium can occur as discrete nonhomogeneous particles in the ore, and the error caused by such a distribution of particles is ± 4% (2o), as determined by

Jan 1, 1984

By S. Shapiro, R. G. Ames

Background Research on the respiratory health of coal miners has focused predominately on the relationship between coal mine dust exposure and ventilatory function impairment (Lapp et al., 1972; Jacobsen, 1976), on the prevalence of coal workers' pneumoconiosis (Lainhart et al., 1969; Morgan et al., 1973), and on coal miner mortality (Ortmeyer et al., 1974; Rockette, 1977). Lesser attention has been paid to the effects of other mining exposures. For example, underground exposure to diesel exhaust emissions (Reger et al., 1980; Ames et al., 1982,1984). An omission in US coal mining research, however, has been identified by the US Office of Technology Assessment (OTA) as the failure to study the effects of inhaled polyvinyl chloride (PVC) thermal decomposition and combustion products (Seltzer, 1979). These products may be released in the mine environment by cable fires, cable explosions, smoldering cables, and conveyor belt fires. In addition to the OTA concern, recent findings of chronic respiratory conditions and other health complications resulting from exposure to PVC decomposition and combustion products in firefighters (Peters et al., 1974; NBS, 1980; NIOSH, 1982; Wallace, 1982), and in survivors of several large scale PVC-fueled fires (Dyer and Esch, 1976; Wallace, 1981, 1982), add immediacy to the concerns. PVC decomposition and combustion PVC decomposition is initiated at temperatures far below ignition (Hartstein and Forshey, 1974; Wallace, 1981). Hence, exposures to decomposition products from smoldering cables may be important health hazards in addition to cable insulation combustion products. Hydrochloric acid (HCL) appears to be the principle toxic substance from the thermal decomposition of PVC since up to 60% by weight is released as HCL (Barrow et al., 1979). HCL is released both as a gas and as an adsorbant on soot particles (Stone et al., 1973), thus allowing penetration of respiratory defenses. In addition, laboratory results indicate that phosgene (carbonyl chloride), a potentially lethal gas, may be produced in significant quantities from electrical arcing of wires covered with PVC insulation (Woolley, 1971; Brown and Birky, 1980). Health concerns related to PVC Toxic effects resulting from high level exposures to PVC pyrolysis and combustion products in animals (Cornish and Abar, 1969) and in humans (Wallace, 1981) is beyond question. Analyses have reported acute, or short-term, health effects resulting from exposure to PVC decomposition and combustion products (Peters et al., 1974; Polakoff et al., 1975). Recently, however, several studies have found that acute effects are often followed first by apparent healing, and then by delayed chronic effects. This pattern of consequential respiratory involvement among persons involved in major PVC-fueled fires has been noted in firefighters, specifically the 1975 New York Telephone Exchange fire (Dyer and Esch, 1976; Wallace, 1982), and the survivors of the 1977 Beverly Hills Supper Club fire (Wallace, 1981). An obstructive syndrome (low FVC and FEV1) was seen in 15% of workers three months following fighting a PVC-fueled fire (Colardyn et al., 1976). Long-term respiratory symptoms seen in studies of survivors of PVC-fueled fires include the bronchitis symptoms of cough and phlegm, and lung dysfunction (Wallace, 1981). Additional support for the thesis of longer-term respiratory effects resulting from PVC-fueled fires is derived from the finding that four persons who initially survived the Beverly Hills Supper Club fire died within nine months of the fire of severe respiratory impairment (Wallace, 1981).

Jan 1, 1986

By Timothy C. Siegel

A piled raft refers to a shallow foundation that is structurally connected to the piles, while composite ground refers to a soil-pile matrix where the piles are not structurally connected. The design objectives for both a piled raft and composite ground are (excluding special considerations such as expansive soil): (1) to provide a sufficient ultimate resistance and (2) to distribute the load into the soil-pile matrix so that the settlement experienced by the shallow foundation is within tolerable limits. A simplified model is proposed for a shallow foundation on composite ground where the foundation settlement is estimated as the sum of the downward movement of the piles plus the downward movement of the shallow foundation relative to the pile head. The proposed simplified model is applied using conventional geotechnical analyses for two hypothetical examples of shallow foundations undergoing compression settlement.

Jan 1, 2011

By J. W. Jang, I. Iwasaki

Introduction Grinding ball wear in wet grinding is due to a complex combination of abrasion, corrosion, impact and their interactions. The ball charge is continually falling from a height greater than half of the ball mill's diameter, and contact is made with ore particles or other balls. Abrasive wear occurs through penetration and plowing of media materials from the ball surface by hard ore particles (Gangopadhyay and Moore, 1985). Electrochemical interactions between the abraded and unabraded areas of the ball surfaces, as well as between the grinding media and the minerals, occur in grinding mill pulps (Adam et al., 1986). The wear depends on the media composition, the hardness and the corrosive/abrasive characteristics of the slurry. The marked-ball-wear test method was used to evaluate the performance of grinding media under nitrogen and oxygen atmospheres. Also, the wear mode was studied by observing the grinding media surface under a scanning electron microscope. In general, grinding media of high hardness and high chromium contents were found to have better corrosive wear resistance than those of low hardness and low chromium contents (Jang, Iwasaki and Moore, 1988). The purpose of this investigation was to determine the size distribution and the shape of wear debris in a study of the wear rates and wear behaviors of grinding balls. Experimental Materials The grinding ball alloys used in this investigation were: •martensitic stainless steel (MSS; 0.96% C and 16.2% Cr), •high-carbon, low-alloy steel (HCLA; 0.89% C and 0.53% Cr), and •mild steel (MS; 0.22% C and 0.09% Cr). The mineral used in this study was synthetic corundum, because it was on hand and contained no magnetic impurities. Debris A 203- mm (8-in.) diam porcelain mill was used for grinding the corundum. The mill charge consisted of: •1200 g of 12-grit synthetic corundum, •770 mL of 0.05 mole/L Na2SO4 (61% solids), and •125 steel balls of nominally 25-mm (1-in.) diam. To minimize the debris corrosion, nitrogen was introduced into the mill. Grinding with MSS, HCLA-steel or MS balls was conducted for 2 hr at 51 rpm. The grinding time using the MS ball was varied from 0.5 hr to 2 hr in an attempt to study the debris amount and shape as a function of time. The debris was collected with a hand magnet from the ground slurry and separated from the corundum particles using a Davis magnetic tube. After the separation, the debris particles were immediately washed with acetone and then filtered and dried. Debris size analysis Buckbee-Mears 3-in.-diam, micro-mesh sieves and an electromagnetic shaker were used for determining the debris size distribution. In sieving, isopropyl alcohol was used. The debris fraction collected from each sieve was washed with acetone, dried and then weighed on an analytical balance. [ ]

Jan 1, 1993

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity -clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 10, 1985

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity-clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 1, 1986

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

Introduction Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 12, 1986

By D. M. Avant, A. J. Solomon, S. M. Pickering, W. R. Fox

Introduction Most high purity silica is produced from crystalline quartz, generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found that is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies, Illinois Minerals Co. and Tammsco Inc., mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, IL. Both companies mine from various locations within a 10-mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Co. mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, AR. Geology The southern Illinois white tripoli area is on the southern flank of the Illinois Basin. The commercial silica zone is a facies of the Clear Creek chert of Lower Devonian Age. To the north, where it occurs deep in the basin, the Clear Creek is a siliceous limestone. In the mining area, thin overburden has allowed access by surface ground water, which has leached away the carbonate content and left a quite pure silica residue. Fossils characteristic of sea bottom deposition, such as brachiopods and trilobites, are occasionally encountered in mining. The structure of the mining area is poorly known, due to infrequent outcrops. Strata in most mines are inclined at dips of 5° to 20°. There appear to be occasional high angle normal and reverse faults, but these are seldom of any significance in mining. The friable white silica zone mined in the Clear Creek chert is overlain by dark brownish-red chert and siliceous shale. Exploration drilling to date has not encountered the base of the microcrystalline tripolitic zone. Chemical content Leaching by ground water solution has removed virtually all the carbonate from the original siliceous limestone. Impurities encountered are red to yellow iron oxides, aluminous clays, and occasional black manganese oxides. The silica has no detectable formula water. A typical chemical analysis and physical properties are listed in Tables 1 and 2. Mineralogy and crystallinity Southern Illinois friable tripoli appears amorphous under the polarizing microscope. No crystal structure and only occasional, vague, patchy anisotropism is evident. However, the material gives an excellent quartz X-ray diffraction pattern. Thus, so far as X-ray mineralogy is concerned, the material is clearly

Jan 12, 1986

By K. Mulukhov

Introduction The depth of open-pit mines continues to increase. The typical designed depth for large quarries is now in the 300 to 600 m (1,000 to 2,000 ft) range, with some quarries even reaching depths of 700 to 800 m (2,300 to 2,600 ft). The cost of handling material from such deep mines can be 60% to 70% of the total cost. The capacity of using a cyclic means of transport, such as trucks or skip hoists, continues to drop as the depth of the mine increases. In addition to the problem of maintaining relatively low slope angles for haul roads, increases in environment pollution and increased fuel consumption make the use of trucks ineffective below 100 to 150 m (300 to 500 ft). In handling large quantities of bulky materials, i.e., more than 15 to 20 Mt/a (16 to 22 million stpy), under fixed terminal points, belt conveyors are preferable in almost in all cases. An exception is when the lump size of the load is too high for the conveyor to handle. Belt conveyors in mines can handle loads having a maximum lump size of no more than 250 to 300 mm (10 to 12 in.). The use of a movable crusher prior to the belt conveyor in an open-pit mine would make the process very expensive. Such an operation could not compete with truck haulage on a cost basis. Belt-car conveyor The main factor that restricts the lump size for conventional belt conveyors is collision impacts between the load-carrying belt and idlers. These impacts are completely eliminated in the belt-car conveyor, which was previously described by Mulukhov (1977). The unique feature of the conveyor is that the load-carrying belt is supported by moving cars. Each car consists of a troughed cross strap that supports the belt with the load and two rollers, on which the cars move along upper and lower rails. Cars are connected by two endless chains revolving over sprockets. The system uses conventional drive pulleys, tail pulleys and return idlers. There are no fasteners between the carrying belt and the car cross straps. The conveyor belt simply drives the cars along by the force of friction between the belt and the straps. A belt-car conveyor was first installed in 1970 at the Karatau mining operation in Kazakhstan. The system was an elevating conveyor with an inclination of 20° and was located on the final part of the truck haul road. The conveyor transferred blasting phosphate ore from the quarry to the crushing plant. A bunker was mounted between the trucks and the conveyor. The maximum lump size was typically 1,200 mm (48 in.). However, there were some lumps as large as 1,500mm (60 in.), which was greater than even the belt width (Fig. 1). Because the prototype belt-car conveyor was intended only for industrial trails, it had a relatively short length of about 50 m (160 ft). Nevertheless, the conveyor yielded a substantial profit over the cost of truck haulage. Naturally, the first question one might ask is why such a system is not now widely used. The reason was the further development of a huge transporting complex for the whole quarry at the base of the belt-car conveyor. After successful industrial trials from 1971 through 1973, which demonstrated the systems engineering feasibility, the State Planning Committee of the USSR included the development of the belt-car conveyor in its plan for the development of the national economy. However, mistakes were made. First, a single organization was not in charge of the development. Second, a plant that was not specialized in belt conveyors was put in charge of the design and manufacturing of the conveyor system. In addition, the crusher was installed before the stacker, which negated the major advantages of the belt-car conveyor. For loading the conveyor, a special blade feeder with pendulum suspension was developed, but it was found unreliable. The main conclusion was that, in-

Jan 1, 2003

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By F. D. Mendes, A. H. Martins

The high copper grade in the Igarapé Bahia (Brazil) gold-copper ore restricts the direct application of the classical cyanidation process. Copper oxide and sulfide minerals react with cyanides in solution, causing high leach-reagent consumption, raising processing costs and decreasing gold recovery. According to studies, a feasible solution would be to pretreat the ore to remove copper minerals prior to cyanidation. The goal of this experimental work was to study the conditions for the removal of copper from the Igarapé Bahia gold-copper ore by sulfuric acid leaching, applying a statistical approach to the experimental design. By using the Plackett Burman method, it was possible to select the variables that exhibited the largest influence on copper extraction at the sulfuric acid leaching stage. These variables were leach solution temperature, stirring speed, sulfuric acid concentration in the leach solution and ore particle size. The individual effect of these variables and their interaction influences on the experimental response were analyzed by applying the replicated full-factorial design method. Finally, the selected variables were optimized by the ascending-path statistical method, which determined the best leach experimental conditions for maximum copper extraction. The optimized leaching conditions resulted in a copper extraction of 75.5%. Keywords: Copper, Gold, Extraction, Sulfuric leaching, Optimization

Jan 1, 2003

By John J. Dran

The elaborate analytical techniques for risk analysis used by the large mining companies in conjunction with the valuation of mineral reserve sites are totally inappropriate for the small miner. The small miner does not possess the financial and technical resources which are available to the large companies for such risk analysis. Even if these resources were available to him, the relatively small size of his investment would not justify a huge expenditure for risk analysis. What is required by the small miner is an improvement over the single point estimates provided by the valuation techniques that he currently uses. Such improvement should provide an indication of the extent to which the true value (known only after the fact) might differ from his estimated value of the mineral reserve site. In addition, a rough indication of the chance of occurrence of various differences between the true and estimated values would be helpful to him. These improvements must be obtained at low cost to be useful to the small miner. Such improvements would have to be based on a simple system requiring very few additional estimates by the miner. The small miner is not accustomed to dealing with sophisticated risk analysis techniques. Hence, any complex, time-consuming approach would be doomed to disuse or possible misuse. A simple, uncomplicated approach requiring a minimum of additional estimates by the miner can be based on a system devised by Frederick S. Hillier Although Hillier's method can be applied to various mineral reserve valuation methods used by the small miner, this note is specifically oriented to the discounted cash flow model. The basic discounted cash flow (DCF) approach provides a single point estimate of value and introduces the concept of risk (i.e. the possibility that the annual cash flows may differ from their estimated values and thus lead to an incorrect investment value) through the use of a risk-adjusted discount rate. This approach simply lowers the present value estimate with increases in the discount rate (i.e. increases in the risk assessment). The single point estimate still remains. Although the lower value estimate makes it less likely that the risky investment will be deemed profitable and undertaken, it provides no indication of risk that is suitable for examination and analysis. In addition to the "best guess" estimate of annual net cash flows required in the DCF model, application of the Hillier risk analysis model requires that the miner

Jan 1, 1976

By V. B. Achanti, A. W. Khair

Developing a laboratory procedure for the determination of coal-seam compressive strength has been a subject of discussion for many decades, and the reliability of laboratory determinations is often the subject of debate. A coal seam’s characteristics, the method of sample collection, the specimen preparation method and the testing procedure can often result in drastic variations in the test results. In this paper, the development of a laboratory testing procedure for the determination of coal-seam compressive strength is presented. Two samples that were collected from different coal seams were tested in this study. First, the inherent characteristics, i.e., coal structure. Hardgrove grindability index (HGI), Slake durability index, proximate analysis and mechanical properties (Young's modules and Poisson's ratio), of each coal were determined. The results were used to categorize the coal scams in terms of the characteristics liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes, cylindrical and cubical, were tested to determine which shape produced the most reproducible strength values. Third, four loading rates within the static testing range, i.e., 0.007, 0.07, 0.34 and 0.7 MPa/s (1.0, 10, 50 and 100 psi/sec), were used to determine the ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics, were established. Background Laboratory testing of coal specimens for the determination of seam compressive strength has been a subject of discussion since the early 1900s. Many researchers have tested coal specimens to estimate coal-seam compressive strength for use in pillar design to insure the safe operation of [ ] mines (Unrug et al., 1986; and Hirt et al.. 1992). Yet, there is a lack of a universal procedure, and, no matter which approach is used, it becomes the subject of intensive debate. A great deal of work has been performed on the subject, and there is much information available in the literature. Some of this work concerns quantifying the influence of specimen shape and size on compressive strength (Bieniawski. 1968: Barron et al.. 1992: Khair and Xu 1994; and Khair 1994). As indicted in the literature, coal is a heterogeneous material, consisting of discontinuities such as cleats and bedding planes, which are likely to produce variable strength results (Holland, 1964; Unrug et al., 1986). Some of the prominent issues that influence the determination of coal-seam compressive strength in the laboratory are: •the collection of a representative sample from a coal seam; •the geometry, i.e., shape and size of the specimens to be prepared and tested: •the loading rate at which the specimens are to be tested:

Jan 1, 1997

By Gordon A. R

The effect of various types of solid carbonaceOlls reductants on the rate of fuming of zinc from lead blast furnace slag was investigated at I250°C.The results of the laboratory experiments indicated that the rate of removal of zinc from slag depended primarily on the volatile matter contents of the reduclants. The effects of fixed carbon, moisture and ash contents were less significant.

Jan 1, 1992

By Ghosh I, Vanangamudi M

Experiments have been made in a laboratory heavy media separator at various specific gravities of separation using zinc chloride solution and magnetite suspension as media for different types of coals. The results indicate that the magnetite bath gives at better separation than zinc chloride solution. Even though the probable error remains the same for most conditions of operation, the error area is found to have a wide variation which emphasises the importance of the error area over probable error in evaluating the performance of a cleaning unit.

Jan 1, 1981

By R. K. Mehta, C. W. Schultz, J. B. Bates

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained. Experimental equipment and procedure The arrangement of the column cell and auxiliary equipment for continuous flow testing is shown schematically in Fig. 1. The feed sump [O] is filled with a sufficient volume of prepared sample to permit a large number of tests to be performed (typically 12). Past experience has shown this is necessary to control sample variability and variability in the size distribution resulting from ultra fine grinding. The feed slurry is maintained at about 20% solids and is constantly recirculated and stirred. The sample is metered from the circulating pipe by a peristaltic pump [O]. The feed slurry is diluted with reagentized water [O] by a second peristaltic pump [O]. Wash water [O], also reagentized, is supplied through a third peristaltic pump [O]. While this feed system may seem unduly complex, it does permit users to independently vary either the wash water rate or the net solids content of the cell. In the tests reported here, the feed rate and net percent solids were constant at 12.5 gms/min. and 3.3%, respectively. Diluted feed enters the column through 6.35 mm-diam (0.25 in.-diam) copper tubing and is discharged upwardly at the center of the column. Tailings are discharged through flexible tubing that can be adjusted so as to control the position of the pulp-froth interface. The column is 76.2 mm-internal-diam (3 in.-internal-diam) and 1090 mm (43 in.) high. It is made from lucite tubing and is fitted with a 51-mm-diam (2-in.-diam) fritted glass air sparger having an average pore diameter of 50 µm. In performing a series of tests, the concentrate and tailing are allowed to discharge continuously. The system is allowed to equilibrate for 30 minutes after the pulp and froth reach operating levels. Concentrate and tailing samples are taken simultaneously for timed intervals (five to 15 minutes, depending on the volume of sample desired). After sampling, a change in operating conditions is made and the system is again allowed to equilibrate. The tests to determine the effect of the pulp-froth interface level were part of a larger series of tests in which the objective was to optimize the conditions for a rougher flotation stage in a two stage circuit. The sample used in this series of tests was an Alabama shale ground to d90 = 23.1 µm and d50 = 7.9 µm. The operating conditions remaining constant in this series of tests were as follows: Column height - 1600 mm (63 in.) Air sparser - 50 µm (average pore diameter) Spray water - 130 cc/min. Feed rate - 12.5 gm/min (0.4 oz per min) (dry solids) Percent solids - 3.3% Frother (Dowfroth 250) - 45 ppm The variable test conditions are tabulated in Table 1. Positions of the pulp level (pulp froth interface) and feed entry are presented as a percentage of column height (as measured from the face of the air sparser). These test conditions are presented Fig. 2. At each of these test conditions, individual tests were performed at varying air

Jan 1, 1992

By Mahoney M

For gas content analysis in recent years, it has been standard procedure to report results on a 'dry ash free' (daf) basis, under the assumption that gas only adsorbs onto coaly material. In order to test the relationship between ash and sas content, samples of various rock types were taken from two drillholes in the Newcastle Coalfield. The results of this study confirmed the correlation between gas content and ash, providing an accurate means of relating gas contents for all carbonaceous rock types.

Jan 1, 1995

The addition of binder to full plant tailings significantly affects the rheology of a backfill mixture and, consequently, the pressure gradients in the pipeline. The binder increases the yield stress and apparent viscosity of the mixture, and the transition velocity between the laminar and turbulent flow regimes. In a test conducted at a slurry relative density of 1,72 with binder addition, the mixture also exhibited time-dependent behaviour owing to the hydration of the binder.

Jan 1, 1993