Search Documents

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By Haoran Zhang, Chu Ho

A recent design-build project in New York involved various degrees of additions and improvements to four existing transit stations. Reuse of the existing foundations was considered a more sustainable alternative than constructing new foundations for the project. This approach mitigated the extent of demolition work and limited the amount of downtime for track operations. A key challenge for reusing the existing foundations was the lack of as-built drawings. In order to obtain some measure of confidence for the proposed foundation reuse, non-destructive investigation technology was adopted to evaluate the structural integrity of the piers and foundations. A total of 47 piers for the existing passenger platform were investigated for possible reuse. Several test pits, excavated to verify the foundation type and configuration, indicated the piers were founded on a combination of shallow footings and drilled shafts. Pile integrity tests were performed to verify the length of the drilled shafts. Geotechnical capacity of drilled shafts was evaluated for side friction and end bearing resistance, and confirmed using a proof load test conducted from the existing platform structure. This paper presents the investigation methodology and discusses the approach adopted for geotechnical design of the existing foundations for reuse.

Sep 8, 2021

By F. Z. Schellenberg

(Pittsburg Meeting, March, 1910.) SYSTEMATIC exploitation in the Pittsburg coal-seam on a large scale is simple where the boundaries of the property do not interfere by forcing drainage-, ventilation-, and transport-lines of entries to be run to particular confined fronts. A prime condition governing development is the natural direction of the seam's perpendicular cleavage-planes, giving long lines of smooth faces near together and parallel, bearing about 65° to the left of the meridian and therefore crossing the basins. The gradients of dip into the basins change from 10 per cent at the east rim to practical flatness northwestward across the great coal-fields, a hundred miles wide; the clip being halved in rate at each successive crossing-over of an anticlinal crest. Elevations above sea-level on this transverse section, in scope of present development, differ by 1,000 ft. between low trough and high outcrop. Local irregularities of dip are found, but the main feature to be recognized is the pitch of the basins-the general rise northeastward at 20 ft. per mile, from 100 ft, below sea-level at the low point near the. SW. corner of Pennsylvania to 1,500 ft. and more above tide, and the appearance then, at the surface, of the lower coal-seams carried in the next deeper-lying thousand feet of rock-measures; below which series come the oil- and gas-sands of Oliphant's charted column of strata, reaching down altogether 3,000 ft. below the Pittsburg coal-seam. Because of -the general regularity of occurrence of the coal-seam, the mine-map depicting the courses of economic operation to be undertaken and the steps in controlled exhaustion, need be but a projection of two dimensions on the horizontal plane of space, and this for the most part composed of natural, almost unbroken lines, on the face and on the end of the coal, co-ordinating rectangularly.

Jul 1, 1910

By Matthias Pulsfort, Jiarui Du, Torsten Wichtmann, Achim v. Blumenthal, Diethard König, Rowena Verst

The influence of the interaction between support fluid and soil, e.g., filter cake formation, on the shear stress transfer in the soil-concrete interface of diaphragm walls and bored piles is still controversially discussed. Actual research on the soil-concrete interface using bentonite suspensions indicates that shear stress transfer is underestimated by existing standards. Investigations on the soil-concrete interface using polymer solutions are rare. Therefore, complementary field investigations and systematic laboratory studies were conducted to analyse the soil-concrete interface using both bentonite suspensions and polymer solutions. Thickness and composition of real-scale filter cakes were investigated on several slurry wall construction sites, where bentonite suspensions were used. Direct shear tests (60 mm x 60 mm) were executed for soilbentonite mixtures with varying amounts of bentonite and different granular fines representing a realistic bandwidth of in-situ filter cake compositions. Larger direct shear tests (300 mm x 300 mm) with preceding horizontal penetration, subsequent vertical tremie concrete placement, and filter cake consolidation were performed using both bentonite suspensions and polymer solutions. The results support the view that shear stress transfer in the soil-concrete interface can be described by a wall friction angle in a range of 25° to 30° for bentonite suspensions and between 35° and 40° for polymer solutions in non-cohesive soils.

May 1, 2022

By Jochen Petersen

Design and operation of heap leach processes are still largely based on,operator experience and rule of thumb. Although considered a low-cost, low-tech route for mineral extraction, the underlying physical, chemical and biological processes are actually rather complex. Numerous heap leach models have been devised over time, but the majority of these tend to simplify the true process and are of limited use in practise. The modelling approach presented here combines the more conventional reaction-diffusion model with models accounting for equilibrium reactions in solution, bacterial growth kinetics, complex reactions schemes, gas flow, heat conservation, etc. One particular model application is discussed in the context of developing a novel high temperature heap leach processes using thermophile micro-organisms. The complexity of processes such as this can only be appreciated with the aid of a systematic model. For the designing engineer an accessible, personal computer based model should be an indispensable tool for the design and optimisation of efficient heap leach operations.

Jan 1, 2002

One of the important directions of further increase of quality and efficiency of control of mining companies and branches is the creation of the operation and development monitoring systems of such facilities. The main purpose of these systems is to provide managers with reliable and timely information on the current state and typical tendencies of operation of the facilities under control. However until the present time no scientific and methodical ground for system monitoring of the mining companies and branches has been created. Therefore, the authors of the report have aimed to assess the current situation with regard to the researches in this field and to do analysis of the most important aspects and ways of solution of the issue under consideration.

Dec 6, 2010

By Deepak Malhotra

The economic viability of mineral companies not only depends on maximizing mineral recoveries but also on their ability to do so at minimum cost. Increasing pressure to cut costs has resulted In reduced staff, thereby decreasing the capabilities of routine metallurgical audits. This paper reviews a systematic approach to plant auditing which has been used successfully at several operations. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1991

By Zhaohui Wang, Jiachen Wang

"Effective surrounding rock control is a prerequisite for realizing safe mining in underground longwall faces. In the past three decades, longwall top-coal caving mining (LTCC) and single pass large height longwall mining (SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increase the difficulty of ground control. Longwall face failure is a common problem in underground mining, which is induced due to low strength and high fracture density of the coal seam. Moreover, the stiffness of main components included in the surrounding rock system also greatly influences longwall face instability. Correspondingly, the surrounding rock system is developed for LTCC and SPLL faces in this paper. Mechanical conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata, and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between its ultimate bearing capacity and the load imposed on it. The influence of coal strength, stiffness of the coal seam, roof strata, and hydraulic support, as well as the movement of roof structure, are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.INTRODUCTIONThe concentration of coal mining in China is gradually shifting to the west region, and there are a large number of thick coal seams in the newly formed coal mining area. Therefore, the surrounding rock control problems related to mining of thick coal seams will become the focus of research in the field of mining engineering in the future. There are two kinds of mining methods for thick coal seams in China, including single pass large height longwall mining (SPLL) and longwall top-coal caving mining (LTCC). Both methods can accomplish the goal of excavating the full thickness of thick coal seams at one time. SPLL mining benefits from the improvement of the development level of associated equipment. The appearance of large hydraulic supports and high power shearers ensure that the height protected by the hydraulic supports and the height of the sheared coal are the same as the coal thickness. LTCC mining benefits from mining technology advantages. The thick coal seam is divided into two sub-layers, and the working face is normally installed in the bottom layer, while the top coal is caved under the compressive forces due to mining. Therefore, there is a scraper conveyor at the front of the hydraulic support for transporting the sheared coal and another one at the tail for transporting caved top coal. Both SPLL and LTCC methods realize one-off recovery of thick coal seams."

Jan 1, 2018

By Mayank Srivastava, Satya Harpalani

Production of methane is an inevitable consequence of mining coal. Although the number of mines practicing recovery of methane prior to, or during, coal mining is increasing, ventilation air methane (VAM) is still a significant source of methane addition in to atmosphere. Recent studies have shown that there are ways to recover the VAM energy, while simultaneously reducing the methane emission in to atmosphere. This paper discusses a case study, currently underway, to develop a technique to quantify the VAM emission from a mine. It also presents the different VAM utilization techniques and the suitability of one for the mine being studied. Finally, the paper summarizes the research issues that require further investigation.

Jan 1, 2005

By Jan Willem van Bloois

IHC Merwede is world market leader in the construction of specialist dredging equipment; it is a company with a rich history. The Netherlands is a coastal western country for which water management is a very important issue. Without the enclosure of the coastal areas with dikes and dunes almost two third of the Netherlands would be flooded. These activities are mostly performed by the dredging industry and are the foundation of the dredging industry as it is today. Besides land protection this industry also carries out infrastructure maintenance and performs land reclamation projects. In essence the dredging industry is specialized in horizontal excavation activities and operations in shallow waters with the purpose of gathering bottom sediments and disposing it at a different location. The development is that the activities are moving to deeper waters to a depth of up to 150m. A few years ago IHC Merwede received a request to perform the shallow water excavation techniques at a depth of approximately 2000 meters for the deep sea mining market. In response to the increasing number of requests for deep sea dredging and mining application solutions, IHC Merwede combined all of its activities in this sector to create a new, specially equipped operational unit, IHC Deep Sea Dredging & Mining (IHC DSDM).

Jan 1, 2010

By J. Lampke

The superior characteristics of iron ore pellets compared with natural ore and sinter are well known. Due to the higher grade and bulk density they show improved transport and material handling properties. While charging blast furnaces with pellets an increased productivity is realized through pellet?s uniform structure and composition. The increased productivity is caused by a high permeable furnace burden with a decreased coke usage via fuel injection and oxygen enrichment. Therefore, a narrow pellet size distribution and a minimum content -6.3 mm are necessary (Meyer, 1980). The required pellet size distribution can be achieved on the one hand by screening the fired pellets after the induration furnace and recycle the undersized pellets. On the other hand it is possible to produce high quality iron ore pellets with a high degree of sphericity, the important narrow grain size distribution ranging between 9 to 16 mm with high green strength directly in the pelletizing device. To produce high quality green pellets, possibilities and knowledge about adjustments of the pelletizing device are necessary. The paper presents a classification of state of the art pelletizing systems in accordance with the advantages of the pelletizing disc and pelletizing drum in issues like adjustability, green pellet quality, the recycling rate and the space requirement. By a systematization of the influences on pelletizing the common reliance of objectives on influence like pelletizing moisture, disc inclination, rotational speed, mass flow and rim height are given. A variety of industry-proven examples are shown, too. Keywords: Pellet, iron ore, pelletizing, pelletizing disc

Sep 1, 2012

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By H. D. Goodfellow, R. A. Elliott

"This paper covers the evolution of large mills and autogenous grinding and compares grinding practice in the iron ore industry with that in the base metal industries. Comments on novel methods of grinding are presented for discussion. Recent developments in the field of classification are briefly reviewed. A systems analysis approach to grinding circuits is discussed. Finally, a point is made for establishing a group within the industry with the purpose of developing a comprehensive evaluation of grinding research and development."

Jan 1, 1971

By R. V. Ramani, T. S. Kovach

In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas that have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development, and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

Jan 1, 1985

By G. Mihaylov

The basic principles of systems analysis are presented. A model has been designed to determine the location of the Main opening in the presence of three or more stock orebodies. The necessary condition is to find a location for the Collection point which is an essential element in opening up each orebody (stock). The model takes into account the total transportation costs from each orebody to the collection point. Three variants are considered provided that the orefield is divided into two levels at least: - a collection point is designed at every level; - a collection point is designed at the lowest level, i.e. where the so-called concentration level is formed; - the collection point is located at a point between the planes of the two levels; The effect of the depth of mining and mine output on determining the method of opening up the orefield has been analyzed by considering a vertical and/or an inclined shaft. A function has been constructed which allows for investigating in both a static and dynamic regime the capital costs for constructing the whole complex including the shaft. The character of the function does not allow finding the global limits. Therefore, it is of particular importance to specify the limiting conditions. In this case these are the flow capacity of development openings and the shaft. The basic groups of cost and natural indicators for assessing and selecting an optimal technological solution have been systematized. The combined analysis of the two approaches to finding the location of the Main opening and determining the mining method enables us to determine when an inclined shaft is best, and the depth at which opening by a vertical shaft has no alternative. Thus, a transition area is formed for which the selection of an optimal technological solution requires an analysis similar to that proposed in this paper. Conclusions are finally drawn which serve as a basis for determining the areas of application of each opening, including the use of a combined scheme of mine opening. The approach presented can be used in both investigating the possibilities for opening up new orefields and reconstructing existing ones in cases when the mining operations go deeper.

Aug 1, 2013

By M Stewart, J Petrie, L Basson

This paper explores tools which have the potential to promote and assess the formation of partnerships between the minerals and energy industries to enhance the economic, environmentally responsible and socially acceptable use of energy. There is a need to look at energy provision and energy services in an integrated manner with key drivers for economic development û both locally and regionally. The minerals sector will remain highly significant to regional economic development in a number of globally significant regions in the medium term. Furthermore, mining, minerals and metalsÆ projects are both consumers and, in some cases (potential), generators of large amounts of energy (electricity included). It is therefore appropriate to focus on the promotion of partnerships between energy providers and the minerals sector which seek to improve resource efficiency within the combined minerals/energy envelope, guided by the tenets of Sustainability.Whilst there has been considerable development of systems analysis tools in recent years to address this sort of æcomplex systemsÆ analysis (Life Cycle Management, Cleaner Production and Industrial Ecology arguments for example), there is no effective roadmap available to decision makers to guide the selection and exploitation of these tools in different contexts. Our previous work developed a Decision Support Framework (DSF) which provides some guidance here, but only within the context of coal-based power generation. The DSF employs the tools of Multi Criteria Decision Analysis (MCDA), within which trade-offs between competing objectives are explored in such a way that alternatives can be compared without necessarily reducing all the different cost and benefits to a common basis (eg a monetary basis). Even if the existing DSF is extended to include all aspects of supply-side management, it is still lacking the necessary tools to analyse energy providers as dynamic network partners within minerals projects (or indeed any resource or manufacturing sector). New models are required for this, which firstly, seek to characterise such network structures, and secondly, enable the application of the necessary analytic tools to exploit these partnerships and networks for optimal performance.This paper explores the development of such an integrated set of network analysis tools, and their relation to the DSF. Due consideration is given to the choice of the attributes needed to characterise partnership linkages and network integrity (eg security of supply of electricity), and the efficiency of material transformations within any node of the network (as a function of energy consumption), and the impact that this has on the viability of other linkages (eg due to reduced availability of raw materials). We discuss how these perspectives help shape the form of objectives to be considered by MCDA.

Jan 1, 2004

By Teresa Sikora

For over 40 years the Institute of Innovative Technology EMAG has specialized in the development of systems and equipment for laboratory and on-line monitoring of coal quality parameters, as well as the implementation of these systems and devices in mines and power stations. Some of these systems, based on advanced radiation detection techniques such as ?-ray backscattering (ALFA-06 and ALFA -06/T systems) or dual energy ?-ray transmission measurement (ALFA-06/2E ash meter), and also the ALFA-06/3E system applying microwave technology for the measurement of moisture, have had numerous applications in Poland. At present, over 100 systems and devices are used in Polish hard and brown coal mines. For over 10 years, EMAG has been specializing in the development of systems and devices, based on natural gamma measurement technology. An on-line ash meter, RODOS and RODOS Ex, based on measurement of natural gamma radioactivity of coal, has been developed and put into operation. This technique has been also used in developing the portable ash meter WALKER and laboratory analyzer GAMMA NATURA. The paper briefly presents features of the above-mentioned devices, their limits and their obtained accuracy, but in particular refers to the laboratory analyzer, GAMMA NATURA, as the first such device in the world, and presents the results of ash and moisture content measurement in hard, brown coals and potassium salts. The possible applications and advantages of the device in coal mines are discussed. The paper also presents the implementation results of the portable ash meter, WALKER, and the on-line ash meter, RODOS, that is used underground in coal mines.

Aug 1, 2013

By G R. Howard, G Back

Management of information systems for data collection is essential to maintain data integrity and continuity, and manage loss control on a large world-class mine such as Telfer Gold Mine. This paper aims to describe the individual systems and protocols of geological data capture at Telfer, then focus on Quality Assurance Quality Control data as an example of loss control in practice. Loss control systems are required to provide capacity, flexibility, structure and management tools to enhance data interrogation. The data that have been collected can then provide geological, financial, environmental, and contractual information to optimise management of business best practice. Telfer Gold Mine is a wholly owned and operated subsidiary of Newcrest Mining Limited. The mine is located in a remote area of NW Western Australia, and has been operating for 20 years. Geological data have been collected at Telfer since 1973. The data include drilling, assay, geological, survey, structural and geophysical data. Data management has evolved through many systems with data stored on many different hardware and software platforms. Commencing in 1995, collation, standardisation and validation of the historic data was completed. This has resulted in the first Access based drill hole database incorporating all available drilling data. This drill hole database, now hosted in SQL Server, is the hub for all geology related data management systems. The Telfer Gold Mine Geology Department has developed a series of inter-related database systems in order to manage the core geology business issues. Databases relating to drill hole planning, drill contract management, geological logging, accounting (standard costing, forecasting, invoice reconciliation), quality control (QAQC), and environment rehabilitation have all been developed to manage loss control. Management effort to provide adequate data systems and protocols has driven the system from concept to utilisation. The improved productivity, data integrity and data analysis capabilities provided by the new database systems at Telfer have allowed for greater confidence in decision making. Systems such as the drill hole and QAQC databases, when utilised in the proper manner provide up-to-date data analysis for resource audits and contract negotiations. The loss control systems are essential to maintain confidence in data integrity and hence directly effect the future of mining at Telfer.

Jan 1, 2000

By Donald E. Scheck

Blasting practices based on sound engineering principles are well established but the successful application of these practices requires accurate information about the overburden geology and close supervision of the drilling and blasting operations. Good design alone is not sufficient to insure good results, but the process may be difficult to control unless steps are taken to measure the variables and to provide management and the operators with the information they need to establish and maintain control. Satisfactory blasting can be defined as loosening and fragmenting the rock so that it can be handled by the excavating equipment, while at the same time, governmental regulations on air blast and ground vibrations are not violated. Optimum practices achieve these objectives at the lowest combined cost of the drilling and loading operations and the blasting materials. Total system optimization, that is, taking into consideration the effect of fragmentation on the cost of operating and maintaining excavating equipment as well as drilling and blasting costs, probably is not a reasonable goal at the present time.

Jan 1, 1984

By T. P. Weldum, B. J. Mahoski, R. S. Rasmussen

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After an overall review of the flow-sheet, two operating circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modeling system, and, on this basis, a quality-assurance program for data gathering was implemented. A number of circuit-design and operating variables were investigated. Statistical analysis of plant-test results revealed relationships previously unquantifiable by any other modeling technique. Improvements in the classification system and in mill grinding efficiencies were demonstrated. As a result, there was significant energy cost savings.

Jan 1, 2000