Search Documents

By S. Yokoya

With increasing requirement of steel productivity and quality in continuous casting in the conventional casting system using an immersion nozzle, it is very difficult to establish a reasonable molten flow pattern. In order to overcome this difficulty, we propose a new method of imparting swirling motion onto the flow in the immersion nozzle and to control the flow pattern in the mold. Following results have been obtained during the studies. For the case of slab continuous casting mold: High amplitudes of oscillation with a period of 10 to 15 seconds are observed in the outlet flow of the immersion nozzle and meniscus flow in the conventional casting system, while these phenomena are remarkably suppressed using swirling motion in the immersion nozzle, which leads to very calm and uniform flow pattern at the outlets of the immersion nozzle, in the mold and on the meniscus in the mold; For the case of billet continuous casting mold: (1) heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl, and (2) Quite different mold flow patterns are observed between the divergent and straight immersion nozzles. Heat and mass transport in the mold using the divergent nozzle is much more reasonable compared to that of straight nozzle. The findings, mentioned above, are very useful to control the flow pattern in the slab, and billet continuous casters. Such effectiveness of swirling flow in the SEN on the mold flow has been put into practical use. As a result, remarkable progress on the quality and production of continuous casting products has been observed in practical application.

Jan 1, 2006

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By Svato Prochazka

Content: ? commonly used drive systems ? drive system efficiency ? introduction to SR technology ? SR drive system advantages Commonly Used Feeder Drives Technologies ? VFD + induction motor ? hydraulic drive + hydraulic motor SR drive + SR motor

May 1, 2010

By Jochen Maurer, Dr. Christian Hoyme, Dr. Hans Regler

Currently, it is very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. As a rule, companies depend on reports from on-site experts. There is no end-to-end digitalization due to the mobility of equipment and ever-changing locations. Equipment from different manufacturers, especially in special foundation engineering, is highly specialized. Any data collected by this equipment is recorded in proprietary formats and made available on the manufacturers' platforms. This exacerbates the situation, making simple analysis of performance indicators impossible. Most functions such as construction diaries, equipment utilization analyses, etc. are implemented only as standalone solutions. This does not allow for prompt visualization and intervention in critical process sequences because the construction site process is usually managed using a cost-based method. Furthermore, special foundation engineering requires a high level of expertise in an extremely wide range of construction processes. In this article, the results from a set of non-proprietary performance analysis tools are presented using numerous practical examples. Once a construction element is completed, the equipment data is immediately transferred to the platform using the latest cloud technology. Because the data is normalized, construction progress can be documented immediately, even for mixed equipment fleets. Bottlenecks can be immediately detected by visualizing the current performance of the production process, which is broken down into individual steps. Modern analyses of this equipment data improve quality, thereby providing better information about current performance. These sets of tools are essential for changing from the current monetary or cost-based method of process management to time- and bottleneck-oriented management. This makes it much easier to identify the critical path during projects. The article shows that processes can be documented and managed.

By H. L. Hazen

The uranium mill at Gunnison, Colorado, started crushing ore Dec. 31,1957, and has now been operating four months. The acid leached ore is washed by counter-current decantation through a system of four classifiers and four thickeners and most of the dissolved uranium reports in the overflow from the first washing thickener. This uranium is extracted from the aqueous pregnant solution by solvent extraction using di-2-ethyl hexyl phosphoric acid and tri-butyl phosphate dissolved in a high-flash-point kerosene as the extracting organic. The pregnant organic is then stripped with soda ash solution. The uranium bearing soda ash solution is filtered to remove insoluble carbonates and any sediment reaching that part of the circuit. The clarified carbonate pregnant solution is then acidified to 3 pH, heated to 180°F to drive off the last traces of CO2, and the uranium finally precipitated as yellow cake with MgO.

Jan 11, 1958

By W. B. Hall, Joy D. Lewis

Mine-run ore is received at Vitro in gondola cars and fed directly to a Cedar Rapids impact crusher. Following screening, the undersize travels through a recently installed three-stage sampling plant where successive cuts are executed by conventional Geary-Jennings type cutters to produce a final sample of 1 lb per ton of raw ore fed. Crushed ore is transported to one of three storage silos or to stockpile, depending upon grade and type of amen- ability. This permits the blending of a mill feed with some degree of consistency. Final grinding is accomplished in one of two closed circuit ball mill-classifier systems allowing simultaneous processing of two basic types of ores. High acid consumers may be leached separately in the required environment. Part of the free acid remaining can then be utilized by an ore stream entering later whose component ores require much less free acid for leaching.

Jan 11, 1958

By L. D. Lash

The key to successful liquid-liquid extraction is the solvent. First, and most important, it must be highly selective for the metal desired and yet reject other metal ions present; second, the ideal sol- vent is completely insoluble in the aqueous feed liquor; third, it has rapid phase separation and will not form emulsions; and, fourth, low cost is desirable, since losses occur even though the solvent is recycled. For this application a solvent known as DDPA (dodecyl phosphoric acid) was chosen since it closely met these requirements. DDPA is a long-chain alkyl phosphate developed for AEC by Oak Ridge National Laboratories, Dow Chemical Co., and the U. S. Bureau of Mines. The long chain contributes to low solubility in the aqueous phase and to high extracting power from acidic sulfate solutions, whereas the alkyl phosphates generally exhibit high selectivity for uranium solutions.

Jan 11, 1958

By C. R. Thomas

Although stainless steels have been used to a limited extent in the South African mining industry, the metallurgical development of 3CRI2 has presented materials engineers with a viable alternative for certain materials-handling applications. The various types of wear involved in these operations are described, and an explanation is given of how 3CRI2 is able to offer advantages, particularly in wet sliding applications. Certain applications result in various types of abrasive wear, and the performance of 3CRI2 in these areas is described.

Jan 1, 1981

By T. Bednarski, T. McCallum

"Physical impurity transfer in solvent extraction (SX) has a significant impact on operating costs, electrowinning (EW) performance, and cathode quality. Some operations use a wash stage to limit impurity transfer by diluting the entrained pregnant leach solution (PLS) to prevent direct transfer to EW. Wash stage operating conditions vary impacting impurity transfer. A number of factors impact dilution efficiency including mixer continuity, wash aqueous acidity, and organic quality. The impact of these variables on dilution efficiency was studied and compared to current industry practice. INTRODUCTION With the exception of iron, impurity transfer in copper SX is due to PLS carryover in the loaded organic via aqueous entrainment and crud movement. The quantity of impurity transfer is influenced by many variables including operating set points, organic quality, and settler housekeeping. Crud management and treatment is a common practice aimed at minimizing transfer of impurities to EW. Crud is a complex solid-stabilized emulsion of aqueous and organic[9]. As such, it contains a large aqueous component and the associated impurities (from the PLS). A common practice is to remove interfacial crud to prevent movement. Additionally, mixer continuity can be altered to enable compaction and improve the efficiency of interfacial pumping[10]. Understanding the factors impacting aqueous entrainment and optimizing the available controls should be a key focus for any operation. Aqueous entrainment in the loaded organic can be impacted by: • Mixer continuity • Mixer organic/aqueous (O/A) ratio • Mixer speed and impeller type • Organic and aqueous depths • Specific settler flow • Use of settler internals (picket fences, coalescing packs) • Organic quality • Design and operation of loaded organic tanks Conventional thought is to run the E1 mixer in aqueous continuity to reduce aqueous entrainment. Generally, O/A ratios close to 1:1 result in improved metallurgical and physical performance. Mixer speeds should be chosen to achieve acceptable stage efficiencies while minimizing over-mixing. Organic depths can be increased in the E1 stage to increase retention time and minimize aqueous entrainment. Settler internals can also be used, but require maintenance to maintain effectiveness. The quality of the plant organic inventory will impact physical performance. Poor organic quality can lead to higher phase disengagement times increasing impurity transfer to the electrolyte. Additionally, the design and operation of the loaded organic tank can impact impurity transfer[8]. Despite the variables that can be used to reduce aqueous entrainment and crud movement, impurity transfer is still an issue in some operations. For these operations with high PLS impurity concentrations, a wash stage may be beneficial to manage impurity transfer. Understanding factors impacting wash stage performance is important to optimize performance and limit impurity transfer."

Jan 1, 2016

By Molloy GR, Eaton RA

The crusher development programme for 7ft Super Extra Heavy Duty (SXHD) Symons cone crushers commenced in 1984. The main objective of the programme was to run the crushers at maxi- mum power for the full life of the liners. This would give a finer product sizing enabling grinding and flotation plant throughput to be maximised. The study was conducted along two basic lines of attack, the first main- taining an effective profile through the life of the liners, the second improv- ing the properties of the liners. It has been found that crusher liner life can be extended and crushing efficiency improved by modification of liner composition and profile.

Jan 1, 1988

By R Sinclair, D Landwehr, I Hunter

"The Syama Gold Mine, located in southern Mali, was established in 1990 by Broken Hill Propriety Limited (BHP). The operation began treating oxide, and in 1994 it transitioned to processing hard and refractory ore based on ‘whole-of-ore’ roasting. In 1996, BHP was succeeded by Randgold Resources and the operation ran until 2001, when it was placed into care and maintenance.The Syama ore is classified as a double refractory ore with pyrite occluding the fine grained gold present in the ore and high levels of organic carbon presenting a challenge in terms of preg-robbing behaviour. The ore is extremely competent and this combination of metallurgical features was the main source of metallurgical problems encountered by the previous owners.Resolute Mining Limited (RML) acquired the Syama project in 2004. Following a feasibility study and the development of a revised processing flow sheet the plant was recommissioned in 2008 using a combination of old and new equipment. The revised flow sheet enabled primary sulfide ore to be treated by flotation and roasting of the concentrate to produce a calcine suitable for conventional carbon-in-leach (CIL) processing.Commissioning and ramp up of the plant was a troubled process, with monthly gold production being as low as 3000 oz in 2010. Poor availability of equipment and lower-than-forecast recoveries were the primary contributors.During the last five years, RML has utilised a systematic approach to improve production, focusing on mechanical reliability, metallurgical recovery and process bottlenecks. Modifications to the circuit have been as a result of both innovation and the application of technological improvements. Improvements have been made to the flotation, roasting and CIL circuits and RML has introduced a deslime circuit to treat flotation concentrate, in addition to the very successful commissioning of a new 1 Mt/a oxide circuit in December 2014. These changes have resulted in gold production increasing to more than 20 000 oz per month in 2015.This paper presents the processes, change implementation and outcomes of the modifications made to the sulfide circuit to address the availability and recovery problems.Apart from the expansion of an existing, world-class deposit and discovery of new resources, future improvements on the path to a class-leading gold mine include the continued reduction of the unit cash cost, increase in overall sulfide circuit gold recovery, increased throughput through continued innovation and consistency in the plant’s operation.Citation:Sinclair, R, Hunter, I and Landwehr, D, 2016. Syama Gold Mine - the Journey towards a Class-leading Gold Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 213–224 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Northern Iron Ltd (NIL) is an Australian listed company that recently brought the historic Sydvaranger open pit Magnetite Mine (the Project) in Northern Norway successfully back into production. NIL made the decision to operate the Project on an owner mining basis, due to limited large scale mining expertise amongst Norwegian mining contractors, a long mine life, a limited range in planned mining rate and to minimise costs. As a new mine operator in a country where labour practices are strictly regulated, there was the desire to reduce the risk associated employing and managing skilled personnel. This was achieved by coupling the purchase of the required mining equipment from the original equipment manufacturer&apos;s (OEM) regional dealers with OEM supported Maintenance and Repair Contracts (MARC). This paper examines the process that was followed to implement an owner mining operation in a short time frame; approximately 12 months from the initial requests for quotation to actual delivery of mining equipment to site, and some of the challenges faced. By following a formal and well-tested process, not only was the implementation achieved in the set time frame, but significant value was added through the cost savings achieved in the equipment purchase price and MARC rates that were negotiated through this process.

May 1, 2010

By Bo Forsman

The computer program SYGRISIS estimates number of units of equipment and operating costs on the basis of yearly production for different loading (wheel loader, LHD, digging arm loader) and transport (truck, train, conveyor belt, hoist, pump) equipment either individually or in any specified combination. Input data are yearly capacity, working time and technical data for the equipment. For the cost analysis input data are technical quantities and unit costs. SYGRISIS is written in TURBO Pascal and can be used on IBM compatible PCs with MS-DOS operating system.

Jan 1, 1989

By T. A. Klinefelter

ONE OF THE many services rendered by the Federal Bureau of Mines is the identification and general examination of ore and mineral samples. Many of these, coming from almost every State in the Union, are clay and shale samples. Other Government agencies, State geologists, universities, and other laboratories are often requested to make similar examinations. This publication describes methods of testing these samples. An earlier paper, published in 1943, described Bureau of Mines methods of testing such clays.3 This paper was to be followed later with another (part II) that would describe much more thorough testing than did the rather general outline of part I. Part I has been out of print for some time and needs revision, and part II was never written; hence, the present publication is designed to include part I and also those additions intended as part II. The tests presented in part I were simple, requiring only the ordinary equipment to be found in any good chemical laboratory. The second publication was to include a greater number of test procedures and information on increasing the accuracy and precision of those previously given.

Jan 1, 1957

By J. Stoll

In May 1998, Hanson Aggregates Midwest, as an outcome of mine planning, offered a 10-acre tract of land containing the famed fossil-bearing Silica formation, to the City of Sylvania, OH. in the form of a 99-year lease agreement. The Olander Park System, and Ohio code park operating within Sylvania Township, was then approved by Hanson and the City to manage and fund the park. All parties signed the lease in August of 1999. In November 2001, local residents voted to fund the park by a margin of 2 to 1. The park will consist of a shallow (approx. 20 ft.) former cement production quarry that is 700 ft. long by 300 ft. wide. Hanson’s motivation and vision for the park was fivefold: 1) the site was located away from long-term reserve access; 2) it would serve nicely as buffer property for the active quarry; 3) it had become an area of illegal dumping by locals in the past; 4) trespassing and safety issues would be limited by allowing supervised usage; and 5) the shallow outcropping contains the world famous, fossil-bearing Silica shale. Hanson will supply shale to the park perpetually via stripping activities in the process of uncovering quality construction aggregate limestone and dolomite reserves. Thousands of enthusiastic fossil hunters have already combed throughout the shale in their quest for “treasures”. The park’s master plan also features nature trails, picnic areas, a fossil-themed play area, amphitheater, visitor’s center and gift shop. Given the natural and people resources that Sylvania Fossil Park will have to offer, Hanson is confident that it will become the premier invertebrate fossil hunting site in the United States. It will also remain a solid community relations vehicle for years to come.

Jan 1, 2003

By E. V. Konoplev

Russia is one of the largest manufacturers of potash fertilizers in the world. Processing of potash ores basically is carried out by a flotation way. Potash ores of the Verhnekamsky potash deposit contain sylvite (KCl), halite (NaCl) and water insoluble impurity (up to 8 %), presented silicate- carbonate minerals, easily slimed by ore crushing in rod mills. Ore of some deposit sites, developed by ?Uralkali? Co, contains a significant amount of a carnal-lite (KCl.MgCl2.6H2O). Work practice of flotation potash plants has shown, that increase of car-nallite content in ore leads to increase magnesium ion content in a circulated plant brine (saturated salt solution of potassium and sodium chlorides-sylvite brine) and to deterioration of indicators of ore processing. In the Paper we present results of researches of floatability of various size sylvite and influences silicate-carbonate slimes on sylvite flotation in brines with the various magnesium chloride content. It is established, that with increase magnesium chloride content in the brine mainly decreases the flotation of coarse sylvite and amplifies adverse effect of silicate-carbonate slimes on sylvite flotation. In this connection deterioration of potash ore flotation is caused not only decrease sylvite floatability but also strengthening adverse action of water insoluble impurity on potash flotation. It is shown that the application of frothing agents, which render the stronger dispersive action on the colloidal-micellar structures of amine in the salt solution increases the absorption of collector on the sylvite and improves the flotation of sylvite into magnesium the containing salt solutions. The application of an organic depressor to the greatest degree of decreasing the absorption amine on the slimes and to the smallest degree possessing anionic properties proves to be most effective with the flotation carnallite of the containing potassium ores. It is offered the application the frother on a basis of glycol ethers and organic depressor on a basis of urea-formaldehyde resin. Results of industrial tests developed reagent modes for flotation treatment of ores with the raised carnallite content (to 6 %) on ?Uralkali? Co plant have shown that their application has allowed to receive equivalent indicators potash flotations at change of magnesium chloride content in the brine from 0.7 % up to 2.4 % .

Jan 1, 2014

By William G. Schultz

Sylvite’s potash mine probably ranks as one of the most highly mechanized and automated mining operations in the world. Employing, on a normal 10-hr production shift, one supervisor and a crew of seven operators, Sylvite is able to mine at an average rate in excess of 600 tph. The ore is produced by two Marietta miners weighing 258 tons, making them the largest and heaviest piece of equipment ever taken underground. The ore produced by these two Marietta miners is conveyed to the shaft area, cycled through a 15,000 ton storage system and hoisted to surface completely automatically. The operation of all equipment in the mine can be monitored and controlled from a central control panel located underground.

Jan 7, 1972

By P D. "Takis" Katsabanis

The phenomenon of sympathetic detonations in blastholes is investigated by comparing experimental observations and numerical modelling results. Numerical modelling using the TDL computer code and Forest Fire decomposition rates for commercial explosives has shown the importance of blasthole diameter, impedance of the stemming and host rock. Comparison with experimental observations has also shown that sympathetic detonations cannot always be treated as shock to detonation transition. Examination of previous results which have been obtained from calibrated low amplitude shock experiments reveal that there is an ignition threshold prior to the detonation threshold. The difference between the two thresholds is more pronounced in the case of air bubble sensitized products. The ignition threshold can be very important under the confinement provided by the blasthole and the conditions of application. It also correlates well with the pressures expected at the gap distances of interest in the practical application. It is suggested that critical energies are used as the criterion for cross initiation in blastholes. Practical suggestions based on the numerical calculations and experiments based on these calculations are also given and discussed.

Jan 1, 1991

By C. E. Jackson, E. C. Nelson, A. L. Christenson

Much information regarding the transfornlatio~lal characteristics of a steel as it cools in a known manner from the austenitic state can be obtained from dilatometric studies. This method has received more arid more attention because of its great flexibility, accuracy, and ease of interpretation. &apos;The method is entirely applicable to any rate of heating and cooling although the experumental procrdures for high rates of cooling have offered some difficulties. This paper presents a description of equipment employing cooling rates up to 500 °C. per secorld and the results of dilatometric observations on six commercial steels are included. French and Klopsch1 studied the cooling transformations of a serirs OF carbon steel, using the thermal arrest method. This was followed by the systematic investigatiol1 of Esser and co-workers on the effect of carhon2 and other alloying additions. in which the transforlnation temperature\ were determined by magnetic induction measurements indicated by a string galranoineter. Emphasis was placed on determining Ar&apos; trailsformations and the critical cooling rates for these steels. The maglietic measurements wrere used in an effort to obtain more accurate data at higher cooling rates. Measurements of thermal arrest were made also to check the validity of the magnetic indications, and good correlation was found between the two, although Esser&apos;s,Ar&apos; temperature measurements on iron-carbon alloys were about 200°F. lower than the measurements made by Fresnch and Klopsch. A notable contril~ution by Esser was the introduction gas quenching. wever and Rose4 used a moving-coil galranometcr in the study of the .Ar and Ar" of iron-carbon alloys by the thermal arrest method and obtained somewhat lover Ar" temperatures than those observed by Esser below I per cent carbon and considerably higher ahove. They concluded that the cooling rate had little influcncc on the Ar" temperatures above 0.4 per cent carbon, although Esser had observed a decrease in the -4r" temperature with increasing cooling rate with similar steels. Digges determined the .Ar" temperature4 for a scries of high-purity iron-carbon alloys, and close agreement with his results was obtained by Greninger. The thermal arrest method. together with metallographic observation used in both these studies, represents the latest investigations of this type. Any investigation by thermal analyses is dependent on the heat of reaction and the specific heat of the

Jan 1, 1945

By L. A. Willey

Although the interierometric method for the determination of length changes was devised by Fizeau more than three quarters of a century ago, it has not achieved the widespread use in the metallurgical field that its precision and simplicity would seem to warrant. The interferometer and the basic principle are both very simple. When optically plane surfaces held at a very slight angle to each other are illuminated by monochromatic light, rectilinear, equally spaced interference fringes arc formed. Each fringe corresponds to a defiuitc thikness of the wedge formed by the optical flat.;. The difference in wedge thickness between two consecutive fringes is cqual to one half the wave length of the illuminating light. Instruments for vicwing the intertero~ncter have passed through a number of modifications. Outstanding among the improvements were those Abbe. in 1884. His improved instrument permitted micrometric mcasurements to the order of one-hundredth of the width of an interference fringe (i.e., lengths were measured to the order of one two-hulldredth of the mave length of light ). It also permitted the consecutive use of light of several wave lengths. which made possible the determination of the order number of any fringe and therefore the absolute thickness of the wedge at any point. The Abbe dilatometer and methods of measuretment, including corrections to he applied for the change of index of refraction with change in tempcrature and barometric pressure in an air wedge, have been thoroughly described by Pulfrich.&apos; Pulfrich2 made further improvements in the interference measuring apparatus. His instrument embodied all the features of the Abbe dilatometer but was made more versatile by its complete mechanical separation from the interferorneter. The introduction of an Amici prism in the piece permitted the simultaneous observ tion of the whole set of fringe systems developed in the interferometer from the visible light of a geisler tulle. .Also, the introduction of a direct-vision, reflecting prism made it possible to set the fringes parallel to the two vertical fiducial line. of the instrument without the necessity of rotating the interierometcr. Interferometric methods employed ill this country have been developed and dcscribed by Priest, Pelers and Cragoe," Austin,5 Merritt,= Saunders,? and Nix and MaNair. Since none of these authors used the type of instrument that was employed in the present investigation, they Will not be discussed here. This paper will be limited to the description of the interfernmetric apparatus and method used at the Aluminum Research Laboratories and to the presentation of data so obtained. Apparatus and Procedure A general view of the dilatometer, not including equipment for controlling and

Jan 1, 1945