Search Documents

By Daniel Kim, Justin McAllister, Shijie Wang

"At the Kennecott Utah Copper Refinery, impurities in the electrolyte are being precipitated in the circulation system and form a hard scale in the piping. This scale must be removed periodically for proper electrolyte flow. Distinct layers of differing composition form as the operating conditions of the tank house change. Scale samples from the inlet and outlet pipes were analyzed to discover the nature of the precipitates. Each sample was sectioned and examined under optical microscopy and SEM. The composition of the scale was analyzed using ICP, XRD, and SEM/EDX mapping. The rate of deposition was determined by measuring the amount deposited on new pipes after elapsed time intervals. In order to determine how to minimize the formation of the scale, the mechanism was studied and the results are presented in this paper.IntroductionIn copper electrorefining, impure copper anodes are refined into pure copper cathodes. The impurities from the anodes are either insoluble and report to the slimes or soluble and dissolve concentrating in the electrolyte. These impurities are controlled by bleeding electrolyte from the system. Over time, the impurities combine to precipitate a hard scale on the surfaces contacted by the electrolyte. The scale causes problems with tank house circulation systems. In order for the refinery to operate properly, the scale must be removed periodically from the walls of the pipes. The first step to control the buildup of scale on the pipes is to understand the composition and the phases that are present in the scale."

Jan 1, 2012

By Ji-He Wei

The ESR of Cu-Cr-Zr alloy has been experimentally investigated. The remelting experiments have been carried out with different slag fluxes in the Cal, + Nal, CaF2 + ZrO2 and CaF2 + NaF + ZrO2 systems on an ESR furnace of 25kg capacity; using a water-cooled copper mould of 96.5 mm diameter, with the forged square bar electrodes of 50x50 mm2. The slag amount was taken to be 1.5 kg. The remelting current and voltage used were 1600-1800A and !5-25K, respectively. The influence of the slag composition on the stability of the remelting process and the losses of alloying elements (2r and Cr) has been considered and examined. The technologies of hot working and heat treatment of the ES ingot have been described and discussed. Some physical properties of the slag in a CuF2 + NaF + ZrO2 system and the remelted Cu-Cr-Zr alloy have been determined. The results indicated that with the slag flux of CaF2 + NaF + l0 mass % ZrO2 and the other operation parameters employed, a high quality ingot of Cu-Cr-Zr alloy may be obtained at the considerably high yields of Zr and Cr by means of ESR. For the remelted Cu-Cr-Zr alloy with a specified composition of 0.5 mass % Cr and 0.1 mass % Zr, the appropriate electrical conductivity, hardness and softening temperature are as high as 45-46S/m, HRB 82-84 and 550°C. respectively. The properties of the Cu-Cr-Zr alloy products are in accordance with and superior to the requirements and specifications of ISO5l82-l99l(E).

Jan 1, 2000

By J. Lui

Inco Copper Cliff Smelter commissioned two new Inco flash furnaces in 1991/1993 as part of its S02 abatement program. Each flash furnace is equipped with a fluid bed dryer. The ~ 12 wt% water content in the concentrate filter cake, flux, reverts and sludge is removed in the fluid bed dryer. The dry solids are discharged from the dryer together with exhaust gases into the baghouses where they are separated. The dry solids are transferred to four storage bins. In September 2003, for the first time since startup in 1991/1993, a large amount of elemental sulfur accumulation was discovered on the walls, roofs and floors of the outlet side of the baghouse chambers. Several baghouse fires were experienced during cleaning and conducting maintenance work in the elemental sulfur contaminated baghouses. Laboratory scale test work at the Inco research lab was conducted to understand the mechanism. A plant solution to minimize elemental sulfur formation was implemented with success. This paper summarizes the efforts to understand and minimize elemental sulfur formation in the baghouse chambers.

Jan 1, 2007

By Chengguo Zhang, Bruce Hebblewhite, Faham Tahmasebinia, lsmet Canbulat

"Coal burst is a dynamic release of energy within the rock (or coal) mass leading to high velocity expulsion of the broken/ failed material into mine openings. This phenomenon has been recognised as one of the most catastrophic failures associated with the coal mining industry, which can often lead to injuries and fatalities of miners as well as significant production losses. This paper aims to examine the mechanisms contributing to coal burst occurrence, with an emphasis on the energy release concept. In this study, a numerical modelling study has been conducted to evaluate the roles and contributions of difference energy components. The energy analysis presented in this paper can help to improve the understanding of energy release mechanisms especially under Australian conditions.INTRODUCTIONCoal burst is one of the most hazardous problems encountered in underground coal mines, which occurs at different locations in a variety of mining systems and operations. This phenomenon always involves a violent and dynamic energy release with large rock mass/coal deformation and ejection that can cause severe damage to openings, equipments and may result in fatalities and injuries.The first coal burst occurrence was reported in Britain in 1738 (Dou 2001). Since then, international experiences are available in Canada, South Africa, USA, former Soviet Union, China, India, France, Germany, Poland and Czechoslovakia. Rice (1935) classified coal bursts as two general types, namely excessive pressure bumps and shock bumps and he further mentioned that pressure bumps are caused when pillar stress exceeds bearing strength. Shock bumps are induced by the breaking of thick, massive strata at a considerable distance above the coal-bed, causing the immediate roof to transmit a shock wave to the coal."

Jan 1, 2016

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By Jiu-ju Cai, Wen-caho Liu, Fei Liu

"With the northern cities of China as study objects, and to confirm Ground-source heat pump system of the environmental benefit and the developing direction. In this paper LCA was applied to the environmental benefit Ground-source heat pump System from raw materials acquisition to system production, utilization and disposal. The conclusion shows that Ground-source heat pump system of the environmental benefit in the northern cities of China. The result showed that Ground-source heat pump system had remarkable environmental benefit. 1. Introduction Life cycle assessment Originate in the sixties of last century, what it paid close attention to is to obtain processing from products raw materials, the processing of products produces, products transportation, products use and maintain to the influence to environment of course. It is a products -oriented environmental management style, it is the environmental management mode of meeting the needs of sustainable development strategy [1]. The research object was in the city and lie in the North of China, would undertake Beijing Olympic Games some football matches in the second half of 08, in order to improve the local environment, adjust the energy structure, reduce the heating consumption of urban coal in the centre, eliminate the coal-burning boiler under 10 tons, since 2005, the local government promotes and utilizes actively the heat pump technology in the source substitute the heating of coal-burning boiler. At present, this area is adopted the technological heating area of heat pump of source reach 20 million square meters, account for this area heat 11.2% of area always, it is estimated, by 2010, adopt the technological heating area of heat pump of source will reach 65 million square meters, the proportion of the area rises to about 30% to account for this area and always heat [2 ]. Study to the whole lifespan of heating system of heat pump of ground source of this area on the basis of LCA method, obtain the products impact on environment of different stages and environmental benefit, find out and reduce or dispel the measure of the influence, improve the environmental benefit of the ground source heat pump heating system.2. MethodologyThe research approach used in this research is the Life cycle assessment, the frame of the research approach is goal and scope definition, the inventory analysis, impact assessment, interpretation.[3][4][5]"

Jan 1, 2008

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By Shulin Nie, Mats Olsson

The mechanism of rock fracture by explosive is a fundamental in rock blasting. It is generally believed that the shock waves from the detonation initiate the fractures. Then the detonation gases penetrate into the fractures and elongate them. However, our previous researches indicated that the detonation gases do not contribute significantly to the fracture propagation. In our latest experiment, blasts have been carried out in 8 large granite blocks. The main goal was to study the fracture mechanism, namely to determine whether the shock waves or the detonation gases fracture the rock.

Jan 1, 2001

By A. Sfougaris

A study on fauna distribution and abundance is being conducted in the Giona Mountain, in central Greece, area of bauxite mining. The specific aims of the study are: a) to estimate and map the distribution of mammals, and especially of the Balkan chamois, b) to estimate and map the distribution and abundance of breeding birds, c) to count the bird species using the area during spring and autumn migration and winter, d) to update the list of mammal and bird species of the mountain, with emphasis on rare and endangered ones, according to 79/409, 92/43 EU Directives and other relevant conventions, e) to compare the bauxite mining areas and species distribution and assess the possible overlap and compatibility of mining activities - species conservation, f) to assess the possible habitat loss due to planned mining activities. All estimations of mammal species distribution and abundance are being carried out by fieldwork using spotlight during the night along selected routes. Especially for chamois, line transects and vantage points with the aid of telescopes and binoculars are being used. Birds are being counted with the point count method in randomly selected plots distributed in all available habitat types and altitudes. The species distribution and mining areas will appear on thematic maps with the aid of a geographical information system (GIS). Finally, solutions for environmentally compatible mining activity in the area will be proposed.

Jan 1, 2007

By D. R. Bomberger

An automatic microscope has been developed to .measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed.

Jan 1, 1963

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By Esperidiana A. B. Moura, Elizabeth Carvalho L. Cardoso, Glauson Aparecido F. Machado, René R. Oliveira

Plastics global annual production exceeds 250 million tons and more than 40% of the total plastic production is used as packaging materials. In recent years polymeric materials derived from biomass have received great attention due to scarce petroleum resources and environmental concerns. PLA is one of the most extensively studied bio-based and bio-compostable aliphatic polyesters; nevertheless, high brittleness and low toughness limits its application. Blending PLA with PBAT (Poly(butylene adipate-co-terephthalate)), an aliphatic-aromatic copolyester, was the solution found due to its high toughness and biodegradability. Differences between PLA and PBAT solubility parameter values lead to the formation of immiscible blends as well as reduction in their mechanical performance besides a poor morphology; so, 5% of pre-irradiated PLA and a previous compatibilized PLA/PBAT (EcovioTM) were added to PLA/PBAT blends in order to improve miscibility phases. Investigations were accomplished on phase morphology (SEM), mechanical properties, thermal behavior and X-ray diffractions (XRD).

Mar 1, 2017

By J. Quinteros-Riquelme

Despite increasing demand, the supply of silver is limited by its inadequate recovery from ores. Due to its scarcity in nature, its high ore variability and complex mineralogy of current silver deposits, its recovery by mineral froth flotation presents a real challenge for process engineers. A silver ore often contains significant amounts of five to ten different silver minerals and knowledge of the mineralogy is a necessary precursor to flotation testing. In this work, a complex silver ore was treated by using batch laboratory flotation, in an effort to find the best experimental conditions to obtain the optimal silver recovery. Mineralogical characterization of feed samples was conducted using a combination of tools, namely the mineral liberation analyzer (MLA) and inductively-coupled plasma mass spectrometry (LA-ICP-MS), which indicated that most of the silver occurred as ?invisible? silver in pyrite. The pyrite assay of the ore was approximately 4%. The ore was processed in two flotation stages. The first stage, sulphide flotation, aimed to collect a sulphide mineral rich concentrate; then a non-sulphide flotation stage was performed by adding sodium sulphide and collectors to the remaining material in the cell, with the objective of obtaining a pyrite rich concentrate. To reach the target recovery of silver from this ore, various variables were altered. In the first stage: mixed collectors, activators, dispersants, and mainstream inert grinding were assessed. In the second stage, the conditions for sulphidization and subsequent flotation were both investigated. From the grade recovery curves for silver and sulphur it was possible to observe a similar metallurgical behavior for both elements, supporting the results given by the mineralogical characterization. Keywords: silver oxide, froth flotation, sulphidization, mig

Sep 1, 2012

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By A. Haldar

The major problem encountered in the casting of hypereutectic Al-Si alloys is the stoppage of flow below the rigidity level of solid fraction. In this study, the flow stoppage mechanism was studied using three Al-Si alloys with 14%, 18% and 22% silicon. The horizontal foam patterns used were 12.50 mm (0.50 inch) wide with two section thicknesses 12.50 mm (0.50 inch) and 6.25 mm (0.25 inch) with a common sprue. The primary silicon distribution along the length of the casting was studied to determine the mechanism of flow stoppage. It was found that the surface of the flow tip of Al-14%Si alloy was smooth with a few undulations. As the silicon level increased, undulations at the flow tip increased. The number and size of undulations were maximum for the Al-22%Si alloy. Microstructural analysis using optical image analyzer revealed that the flow tip consisted mainly of eutectic silicon in the aluminum matrix and a few primary silicon crystals (PSC). The PSC were in the interlocked condition few centimeters behind the flow tip. It was also found that the gap between the flow tip and the PSC concentrated area increased with an increase in silicon level. Phase characterization was done with SEM-EDX to identify the precipitating phases.

Jan 1, 2007

By A. Wahab Khair

This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally con- fined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage.

Jan 1, 1984

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By D. Watson, T. J. N. Grainger-Allan

A technique for studying the mechanism of the froth flotation process in which continuous froth removal does not take place but, instead, an equilibrium is reached between froth and pulp is described. A flotation cell, specially designed to facilitate equilibration, and froth and pulp sampling procedures are described. The main advantage of the technique is that the ability to measure the steady-state froth height allows froth-stability effects to be separated from pulp-process effects. In the flotation of hematite front quartz, linear relationships are found between airflow rate and froth height and between airflow rate and the ratio at equilibrium of mass of values in froth to mass of values in the pulp. A simple mechanistic interpretation of these results is given. It is suggested that froth-stability effects may play a more important role than hitherto allowed. In particular, the way in which concentration and size distribution of gangue particles may affect overall flotation rate is shown.

Jan 1, 1975

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Robin B. Steven

Rio Tinto's Kennecott Bingham Canyon Mine is one of the largest open pit copper mines in the world. In 1988 they completed a $400 million project using a conveying system to transfer the ore from an in-pit crusher to the concentrator. The longest conveyor, C-6, was 17,352ft long and ran in a tunnel through the mountain-side to the concentrator. The belt was removed after 14+ years after carrying 700 million tons of 10 minus ore. The paper discusses the original G6 belt's performance and new splicing methods used to achieve a 60% dynamic splice efficiency on the replacement belt.

Jan 1, 2004